Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel property prediction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

A phenomenological rate of injection model for predicting fuel injection with application to mixture formation in light-duty diesel engines

Fuel injection rate laws are one of the most important pieces of information needed when modeling engine combustion with computational fluid dynamics. In this study, a simple phenomenological model of a common-rail injector was developed and calibrated for the Bosch CRI2.2 platform. The model requires three tunable parameter fits, making it relatively easy to calibrate and suitable for injector modeling when high-fidelity information about the internal injector’s geometry and electrical circuit details are not available. Each injection pulse is modeled as a sequence of up to four stages: an injection needle mechanical opening transient, a full-lift viscous flow inertial transient, a Bernoulli steady-state stage, and a needle descent transient. Parameters for each stage are obtained as polynomial fits from measured injection rate properties. The model enforces total injected mass, and the intermediate stages are only introduced if the injection pulse duration is long enough. Experimental rates of injection from two separate campaigns on the same injector were used to calibrate the model. The model was first validated against measured injection rate laws featuring pilot injections, short partially premixed combustion pulses, and conventional diesel combustion injection strategies. Then, it was employed as an input to engine computational fluid dynamics simulations, which were run to simulate experiments of mixture formation in an optically accessible light-duty diesel engine. It was found that, though simple, this model is capable of predicting both pilot and main injection pulse mass flow rates well: the simulations yielded accurate predictions of in-cylinder equivalence ratio distributions from injection strategies for both partially premixed combustion and pilot injections. Also, once calibrated, the model produced appropriate results for a wide range of injected mass and rail pressure values. Finally, it was observed that usage of such a relatively simple model can be a good choice when high-fidelity injection rate input and highly detailed information of the injector’s geometry and operation are not available, particularly as noticeable discrepancies can be present also among different experimental campaigns on similar hardware.

42 ENGINEERING↗
DOE OSTI2026

Multiphysics simulation of TRISO fuel compacts and the effects of homogenization on silver release predictions

This work studies the impact of explicit and homogenized modeling approaches on the multiphysics simulation of TRistructural ISOtropic (TRISO) fuel compacts in prismatic High Temperature Gas Reactors (HTGRs) and the silver release predictions. TRISO fuel compacts exhibit complex double heterogeneity that significantly affects heat conduction, neutron transport, and fission products release. In this work, we use Cardinal, a multiphysics tool based on the Multiphysics Object-Oriented Simulation Environment (MOOSE) framework, to couple neutron transport and heat conduction. OpenMC is used for neutron transport and the MOOSE heat transfer module is used for the heat conduction. Then, we use BISON for the silver release predictions. Two different modeling approaches—explicit modeling of individual TRISO particles and homogenized representation using effective thermal properties—are compared at high TRISO packing fractions (20% and 40%) across varying power densities. Results demonstrate that homogenization significantly under-predicts peak temperatures, for the case of high power/TRISO, there is a difference of 83.73 K in the maximum temperature. Additionally, homogenization underestimates the silver release predictions compared to explicit modeling. Specifically, the temperature and power density differences lead to significant differences in silver release predictions. This work demonstrates the importance of accurately modeling heterogeneity of the TRISO particles to reliably predict fission product release and assess reactor safety margins.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Modeling and design of a separate effects irradiation test targeting fission gas release from Cr-doped UO 2

Fission gas release (FGR) from nuclear fuel during operation can diminish heat transfer properties across the pellet-cladding gap and increase the fuel rod internal pressure, thereby posing a concern to fuel reliability and safety during an accident. Enlarging the fuel grain size, which has been shown to improve fission gas retention, can be achieved by doping the fuel feedstock prior to sintering. In this work, the BISON fuel performance code was used to predict FGR from undoped and chromia-doped UO 2 (referred to as Cr-doped UO 2 ) fuel specimens with different grain sizes and across various temperatures. The BISON models identified the irradiation conditions for which FGR is most significant, and a separate effects irradiation experiment in the High Flux Isotope Reactor (HFIR) was then developed targeting those conditions. Further, the experiment leveraged the MiniFuel irradiation capability at Oak Ridge National Laboratory and consisted of 12 fuel specimens of varying grain size and Cr content. A coupling scheme between BISON FGR results and the ANSYS finite element thermal model used for experiment design was formulated to predict cumulative FGR from each fuel specimen based on expected irradiation temperature histories. The fuel samples were fabricated and characterized as a part of this work, and the fuel compositions modeled in BISON were representative of the specimens used in the experiment. This combined modeling and experimental effort aims to study the effect of fuel grain size and Cr content on FGR and to provide simulated BISON FGR results that can be used for future model validation activities.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Formation of late-generation atmospheric compounds inhibited by rapid deposition

Reactive organic carbon species are important fuel for atmospheric chemical reactions, including the formation of secondary organic aerosol. However, in parallel to atmospheric oxidation processes, deposition can remove compounds from the atmosphere and impact downstream environments. To understand the impact of deposition on atmospheric oxidation, we present a framework for predicting and visualizing the fate of a molecule on the basis of the physicochemical properties of compounds (Henry’s law constant, vapour pressure and reaction rate constants), which are used to estimate timescales for oxidation and deposition. Further, by implementing our deposition rates in chemical models, we show that deposition substantially suppresses atmospheric reactivity and aerosol formation by removing early-generation products and preventing the formation of large fractions (up to 90%) of downstream, late-generation compounds. Deposition is frequently missing in the laboratory experiments and detailed chemical modelling, which probably biases our understanding of atmospheric composition.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1981

Autoignition characteristics of aircraft-type fuels

An investigation was conducted of the ignition delay characteristics of five liquid hydrocarbon fuels in air. The test apparatus developed permitted independent variation and control of temperature, pressure, air flow rate, and fuel/air ratio in order that the effects of each parameter could be investigated independently. All of the fuels tested behaved in a predictable manner, that is, ignition delay time decreased as temperature, pressure, and fuel/air ratio increased. The results for the different fuels tested (Jet-A, MP-4, No. 2 diesel, ERBS, and cetane) were directly comparable, since it can be shown that the fuel spray characteristics from the multiple conical tube injector are relatively insensitive to small changes in fuel properties (viscosity, surface tension, and density).

Spadaccini, L. J.↗
DOE OSTI2025

Caustic Neutralization and Precipitation of Acidic Dissolved Simulated Stainless Steel–Clad Plutonium and Plutonium/Uranium Nuclear Fuel

Simulated dissolved stainless steel (SS) clad Pu and Pu/U nuclear fuel in HNO 3 was neutralized to a free hydroxide (OH - ) concentration of 0.6 M. A thermal neutron poison, Gd, was added to the simulants at concentrations of either ~3 - 6 g/L or ~37 - 38 g/L. The supernate Pu concentration the day of neutralization ranged from 0.48 to 8.75 mg/L. The supernate Pu concentration of a simplified simulant neutralized to 0.6 M OH - above precipitated solids containing Pu was demonstrated to decrease over 18 days. A significant portion of precipitated Pu was found to be insoluble in 8 M HNO 3 at ambient temperature, but essentially quantitative Pu dissolution was achieved in 11.5 M HNO 3 /0.1 M KF at 100 °C. The difficulty in dissolving the Pu precipitate is believed to be due to the formation of refractory PuO 2 •xH 2 O during the neutralization process. Initial Gd concentrations of ~37 – 38 g/L were found to result in a greater Al precipitation when neutralized to 0.6 M OH - than initial Gd concentrations of ~3 – 6 g/L. Physical properties of the resultant slurries were measured and used to calculate limiting flowrates and slurry velocities by gravity only in transfer piping between the Savannah River Site’s H-Canyon Facility and the Concentration, Storage, and Transfer Facility (CSTF). These results were compared to calculated deposition velocities to predict if solids would settle during the transfer. The Newtonian model was found to be reasonable for each diluted slurry evaluated. Deposition velocities of Pu containing slurries are lower than nuclear fuel slurries primarily composed of U due to the high density of Pu solids. In conclusion, dilution of slurries reduces the margin between the slurry and deposition velocities due to the reduction in viscosity because higher viscous forces on the particles promote maintained suspension.

Actinide Neutralization↗
DOE OSTI2025

Experimental confirmation of first-principles thermal conductivity in Zirconium-doped ThO 2

The degradation of thermal conductivity in advanced nuclear fuels due to the accumulation of fission products and irradiation-induced defects is inevitable, and must be considered as part of safety and efficiency analyses of nuclear reactors. Here, this study examines the thermal conductivity of a zirconium-doped ThO 2 crystal, synthesized via the hydrothermal method using a spatial domain thermoreflectance technique. Zirconium is one of the soluble fission products in oxide fuels that can effectively scatter heat-carrying phonons in the crystalline lattice of fuel. Thus, thermal property measurements of zirconium-doped ThO 2 single crystals provide insights into the effects of substitutional zirconium doping, isolated from extrinsic factors such as grain boundary scattering. The experimental results are compared with first-principles calculations of the lattice thermal conductivity of ThO 2 , employing an iterative solution of the Peierls-Boltzmann transport equation. Additionally, the non-perturbative Green's function methodology is utilized to compute phonon-point defect scattering rates, accounting for local distortions around point defects, including mass difference changes, interatomic force constants, and structural relaxation. The congruence between the predicted results from first-principles calculations and the measured temperature-dependent thermal conductivity validates the computational methodology. Furthermore, the methodologies employed in this study enable systematic investigations of thermal conductivity reduction by fission products, potentially leading to the development of more accurate fuel performance codes.

36 - MATERIALS SCIENCE↗
DOE OSTI2023

An Integrated Simulation of Multiple-Pass U-10Mo Alloy Hot Rolling and Static Recrystallization

To achieve a desired microstructure and minimize the thickness variation in rolled foils, researchers must understand the effects of foil fabrication process variables on microstructure evolution. We developed an integrated simulation of deformation and recrystallization that employs the finite element method (FEM) and the kinetic Monte Carlo (KMC) Potts model, respectively, to investigate microstructure evolution during multiple-pass hot rolling and heat treatment in polycrystalline U-10Mo fuel. Scanning electron microscopy and electron backscatter diffraction images of microstructures were directly used as input in FEM calculation of deformation, and the calculated strains were used to determine the driving force of nucleation and growth of recrystallized grains in the Potts model. Grain structures predicted by the Potts model were used to update the grain structure and material properties for FEM. Simulation alternated between FEM and the Potts model to simulate grain structure evolution during multiple rolling and heat treatments. The initial model parameters were determined by benchmarking the recrystallization kinetics against experimental data. Then, the model was applied to predict the grain structure evolution. Results showed that our model can capture the coupling between deformation and recrystallization and can quantitatively reproduce the observed U-10Mo recrystallization and grain growth kinetics. The simulation results demonstrated that the developed model can predict U-10Mo grain structures as a function of initial microstructure and foil fabrication parameters.

36 MATERIALS SCIENCE↗
NASA NTRS1979

Technology for future air transports

The requirements and opportunities for technological development in transport aircraft of the next generation are reviewed, focusing primarily on conventional, subsonic aircraft. Advances in computational aerodynamics and computer-aided design and manufacturing (in numerically controlled processes) are noted as well as improved wind tunnel testing and drag reduction techniques. Advances in aeroelasticity prediction have made it possible to use flexible, high-aspect-ratio wings without large weight penalties. Weight reduction may be achieved by the use of composite aircraft structures and superplastic forming combined with diffusion bonding, however composites require improvement in manufacturing techniques and mechanical properties in order to gain general acceptance. Propulsion systems can be improved in engine fuel efficiency, control, durability, environmental compatibility (exhaust and noise emissions), and fuel specifications. In avionics, due to the growth of low-cost, miniaturized packages, opportunities exist in the fields of digital controls, navigation, guidance and communication. Applications of new technologies to various aspects of flight safety are also outlined.

Klineberg, J. M.↗
NASA NTRS1988

Analytical and experimental validation of the Oblique Detonation Wave Engine concept

The Oblique Detonation Wave Engine (ODWE) for hypersonic flight has been analytically studied by NASA using the CFD codes which fully couple finite rate chemistry with fluid dynamics. Fuel injector designs investigated included wall and strut injectors, and the in-stream strut injectors were chosen to provide good mixing with minimal stagnation pressure losses. Plans for experimentally validating the ODWE concept in an arc-jet hypersonic wind tunnel are discussed. Measurements of the flow field properties behind the oblique wave will be compared to analytical predictions.

Adelman, Henry G.↗
DOE OSTI2022

Predictive models enhance feedstock quality of corn stover via air classification

Feedstock heterogeneity is a fundamental obstacle to cost-competitive biobased products. Agricultural products like corn stover have anatomical components that vary in their chemical composition, mechanical properties, structure, and response to chemical and biological treatments. A technique that can enrich streams in select anatomical fractions would allow a tailored deconstruction approach to increase overall process efficiency. Air classification can be leveraged for such refining, however, fundamental characterization and understanding of the particle properties that underly the physics of air classification are only modestly documented. Here, we determine fundamental particle properties including mass-to-area ratio, drag coefficient, and partition velocity that describe how anatomical tissues of corn stover behave during air classification. In this work, mass-to-area ratios of anatomical tissues vary by nearly two orders of magnitude from 2.3 mg/mm 2 for cob to 0.04 mg/mm 2 for leaf. Drag coefficients of longer, fibrous materials (i.e., rind, husk, and sheath) are shown to correlate with particle area (p-value < 0.001) whereas granular tissues (i.e., cob, pith, and leaf) correlate better with mass-to-area ratio (p-values < 0.001). When compared to experimental observations, a simulated two-stage air classification and size reduction scenario predicts the overall partitioning of anatomical tissues within 15% for pith, husk, rind, and cob tissues. The model predicts an air-classified fraction preferentially enriched in cob (purity = 20%), rind (purity = 74%), and pith (purity = 4.5%) with a mass yield of 47%. Empirical relations for these properties can be used to predict the partitioning of corn stover during air classification based on anatomical type and size.

09 BIOMASS FUELS↗
DOE OSTI2020

Transgenic Poplar Designed for Biofuels

Members of the genus Populus (i.e., cottonwood, hybrid poplar) represent a promising source of lignocellulosic biomass for biofuels. However, one of the major factors negatively affecting poplar’s efficient conversion to biofuel is the inherent recalcitrance to enzymatic saccharification due to cell wall components such as lignin. To this effect, there have been efforts to modify gene expression to reduce biomass recalcitrance by changing cell wall properties. Furthermore, we review recent genetic modifications of poplar that led to change cell wall properties and the resulting effects on subsequent pretreatment efficacy and saccharification. Although genetic engineering’s impacts on cell wall properties are not fully predictable, recent studies have shown promising improvement in the biological conversion of transgenic poplar to biofuels.

09 BIOMASS FUELS↗
DOE OSTI2026

Development of Machine-Learned Interatomic Potentials to Predict Structure, Transport, and Reactivity in Platinum-Based Fuel Cells

Machine-learned interatomic potentials (MLIPs) have rapidly progressed in accuracy, speed, and data efficiency in recent years. However, training robust MLIPs in multicomponent systems remains a challenge. In this work, we train an MLIP to describe hydrated Nafion ionomers and platinum catalysts, which are important components of fuel cells, by constructing a diverse training set to describe the bulk polymer and interfacial catalyst–polymer interactions well. We use our trained MLIP to study the properties of the platinum–Nafion system, including polymer structure, proton mobility in a bulk Nafion polymer and near a platinum-Nafion interface, and reactions near and far from the interface, finding excellent results for structure and reactions contained within our training set. Transport seems to be well described, with both vehicular transport and Grotthuss hopping captured, although converged calculations of diffusivities were not computed because they require calculations of tens of nanoseconds that are challenging with current state-of-the-art MLIPs. The combined insights that this model provides can be leveraged to optimize fuel cell performance, and the approach can be applied to other chemical processes and devices where structure, transport, and reactivity all contribute to the overall observed performance.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1987

Computer-based phosphoric acid fuel cell analytical tools Descriptions and usages

Simulation models have been developed for the prediction of phosphoric acid fuel cell (PAFC) powerplant system performance under both transient and steady operation conditions, as well as for the design of component configurations and for optimal systems synthesis. These models, which are presently computer-implemented, are an engineering and a system model; the former being solved by the finite difference method to determine the balances and properties of different sections, and the latter using thermodynamic balances to set up algebraic equations that yield physical and chemical properties of the stream for one operating condition.

Lu, C.↗
NASA NTRS2014

NASA Numerical and Experimental Evaluation of UTRC Low Emissions Injector

Computational and experimental analyses of a PICS-Pilot-In-Can-Swirler technology injector, developed by United Technologies Research Center (UTRC) are presented. NASA has defined technology targets for near term (called "N+1", circa 2015), midterm ("N+2", circa 2020) and far term ("N+3", circa 2030) that specify realistic emissions and fuel efficiency goals for commercial aircraft. This injector has potential for application in an engine to meet the Pratt & Whitney N+3 supersonic cycle goals, or the subsonic N+2 engine cycle goals. Experimental methods were employed to investigate supersonic cruise points as well as select points of the subsonic cycle engine; cruise, approach, and idle with a slightly elevated inlet pressure. Experiments at NASA employed gas analysis and a suite of laser-based measurement techniques to characterize the combustor flow downstream from the PICS dump plane. Optical diagnostics employed for this work included Planar Laser-Induced Fluorescence of fuel for injector spray pattern and Spontaneous Raman Spectroscopy for relative species concentration of fuel and CO2. The work reported here used unheated (liquid) Jet-A fuel for all fuel circuits and cycle conditions. The initial tests performed by UTRC used vaporized Jet-A to simulate the expected supersonic cruise condition, which anticipated using fuel as a heat sink. Using the National Combustion Code a PICS-based combustor was modeled with liquid fuel at the supersonic cruise condition. All CFD models used a cubic non-linear k-epsilon turbulence wall functions model, and a semi-detailed Jet-A kinetic mechanism based on a surrogate fuel mixture. Two initial spray droplet size distribution and spray cone conditions were used: (1) an initial condition (Lefebvre) with an assumed Rosin-Rammler distribution, and 7 degree Solid Spray Cone; and (2) the Boundary Layer Stripping (BLS) primary atomization model giving the spray size distribution and directional properties. Contour and line plots are shown in comparison with experimental data (where this data is available) for flow velocities, fuel, and temperature distribution. The CFD results are consistent with experimental observations for fuel distribution and vaporization. Analysis of gas sample results, using a previously-developed NASA NOx correlation, indicates that for sea-level takeoff, the PICS configuration is predicted to deliver an EINOx value of about three for the targeted supersonic aircraft. Emissions results at supersonic cruise conditions show potential for meeting the NASA goals with liquid fuel.

Hicks, Yolanda R.↗
NASA NTRS2014

NASA Numerical and Experimental Evaluation of UTRC Low Emissions Injector

Computational and experimental analyses of a PICS-Pilot-In-Can-Swirler technology injector, developed by United Technologies Research Center (UTRC) are presented. NASA has defined technology targets for near term (called "N+1", circa 2015), midterm ("N+2", circa 2020) and far term ("N+3", circa 2030) that specify realistic emissions and fuel efficiency goals for commercial aircraft. This injector has potential for application in an engine to meet the Pratt & Whitney N+3 supersonic cycle goals, or the subsonic N+2 engine cycle goals. Experimental methods were employed to investigate supersonic cruise points as well as select points of the subsonic cycle engine; cruise, approach, and idle with a slightly elevated inlet pressure. Experiments at NASA employed gas analysis and a suite of laser-based measurement techniques to characterize the combustor flow downstream from the PICS dump plane. Optical diagnostics employed for this work included Planar Laser-Induced Fluorescence of fuel for injector spray pattern and Spontaneous Raman Spectroscopy for relative species concentration of fuel and CO2. The work reported here used unheated (liquid) Jet-A fuel for all fuel circuits and cycle conditions. The initial tests performed by UTRC used vaporized Jet-A to simulate the expected supersonic cruise condition, which anticipated using fuel as a heat sink. Using the National Combustion Code a PICS-based combustor was modeled with liquid fuel at the supersonic cruise condition. All CFD models used a cubic non-linear k-epsilon turbulence wall functions model, and a semi-detailed Jet-A kinetic mechanism based on a surrogate fuel mixture. Two initial spray droplet size distribution and spray cone conditions were used: 1) an initial condition (Lefebvre) with an assumed Rosin-Rammler distribution, and 7 degree Solid Spray Cone; and 2) the Boundary Layer Stripping (BLS) primary atomization model giving the spray size distribution and directional properties. Contour and line plots are shown in comparison with experimental data (where this data is available) for flow velocities, fuel, and temperature distribution. The CFD results are consistent with experimental observations for fuel distribution and vaporization. Analysis of gas sample results, using a previously-developed NASA NOx correlation, indicates that for sea-level takeoff, the PICS configuration is predicted to deliver an EINOx value of about 3 for the targeted supersonic aircraft. Emissions results at supersonic cruise conditions show potential for meeting the NASA goals with liquid fuel.

Hicks, Yolanda R.↗
DOE OSTI2025

A hybrid calorimetry-simulation model of mixing enthalpy for molten salt

Calorimetric determination of enthalpies of mixing (ΔH mix ) in multicomponent molten salts is often interpreted using empirical models that lack physically meaningful parameters. However, for improving pyrochemical separation of spent nuclear fuel, where lanthanides are major fission products and critical elements, a deeper thermodynamic understanding of the link between excess thermodynamic properties and solvation structure is critically needed. In this work, we implement a hybrid and physics-informed framework, MIVM+Calorimetry+AIMD, which integrates experimentally measured ΔH mix (via high temperature drop calorimetry) with solvation structures from ab initio molecular dynamics (AIMD). This approach is demonstrated using LaCl 3 mixed with eutectic LiCl-KCl (58 mol% – 42 mol%) at 873 K and 1133 K. MIVM-derived parameters enable extrapolation of excess Gibbs energy and La 3+ activity across compositions. In contrast, direct ΔH mix predictions from AIMD and polarizable ion model simulations deviate significantly. By incorporating experimentally benchmarked solvation structures into an interpretable thermodynamic model, the MIVM+Calorimetry+AIMD formalism achieves higher accuracy and generalizable method for studying molten salts, offering a robust path for understanding and optimizing molten salt chemistry relevant to nuclear fuel cycles and separation science.

Goncharov, Vitaliy G. [Washington State Univ., Pul↗
DOE OSTI2024

STAT7 v1.2 Verification and Validation Report

This report documents the software testing which has been performed for the STAT7 Version 1.2 (hereafter STAT7 v1.2) software, a code for the statistical propagation of uncertainties in steady-state thermal hydraulics (TH) analysis of plate-fueled research and test reactors. The key capabilities addressed in this testing were selected based on the use of the software for analysis work supporting the conversion to low-enriched uranium fuel of U.S. High-Performance Research Reactors (USHPRR) such as the Massachusetts Institute of Technology Research Reactor (MITR-II). This testing scope includes comparison of the code’s statistical processing capabilities using statistical tests, comparison of coolant property evaluations to NIST data tables, and systematic comparison of key TH solver capabilities to the results of hand calculations and to predictions from PLTEMP/ANL Version 4.4. The good agreement achieved in this testing campaign, within the acceptance criteria of a 1% relative difference, also demonstrates that these capabilities have been implemented in STAT7 v1.2 correctly.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗