SEARCH · Search NASA

Results for “HUB”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

All sources NASA NTRS DOE OSTI

NASA NTRS1975

Shake Test of a Propeller Test Rig in the 40- by 80-Foot Wind Tunnel

A shake test was conducted to determine the dynamic characteristics of a propeller test rig in the Ames 40- by 80-Foot Wind Tunnel. The rotor off hub transfer function (acceleration per unit force as a function of frequency) was measured in the longitudinal, lateral, and vertical directions for shaft angles of 0 and 90 deg corresponding to propeller and helicopter operation, respectively. The dynamic data are summarized for the configurations tested, giving the following properties for each mode identified: the natural frequency, the hub response at resonance, the damping coefficient, the damping ratio, and the modal mass. The complete transfer functions are presented, and the detailed test results are included.

Johnson, W.↗

NASA NTRS1975

Two-stage, low noise advanced technology fan. 4: Aerodynamic final report

A two-stage research fan was tested to provide technology for designing a turbofan engine for an advanced, long range commercial transport having a cruise Mach number of 0.85 -0.9 and a noise level 20 EPNdB below current requirements. The fan design tip speed was 365.8m/sec (1200ft/sec);the hub/tip ratio was 0.4; the design pressure ratio was 1.9; and the design specific flow was 209.2 kg/sec/sq m(42.85lbm/sec/sq ft). Two fan-versions were tested: a baseline configuration, and an acoustically treated configuration with a sonic inlet device. The baseline version was tested with uniform inlet flow and with tip-radial and hub-radial inlet flow distortions. The baseline fan with uniform inlet flow attained an efficiency of 86.4% at design speed, but the stall margin was low. Tip-radial distortion increased stall margin 4 percentage points at design speed and reduced peak efficiency one percentage point. Hub-radial distortion decreased stall margin 4 percentage points at all speeds and reduced peak efficiency at design speed 8 percentage points. At design speed, the sonic inlet in the cruise position reduced stall margin one percentage point and efficiency 1.5 to 4.5 percentage points. The sonic inlet in the approach position reduced stall margin 2 percentage points.

Harley, K. G.↗

NASA NTRS1976

Optimal control of spin stabilized spacecraft with telescoping appendages

The control of a spin-stabilized spacecraft consisting of a rigid central hub and one or two movable offset telescoping booms (with end masses) is considered. The equations of rotational motion are linearized about either of two desired final states. A control law for the boom and mass position is sought such that a quadratic cost functional involving the weighted components of angular velocity plus the control is minimized when the final time is unspecified and involves the solution of the matrix Riccati algebraic equation. For three-axis control more than one offset boom (orthogonal to each other) is required. For two-axis control with a single boom offset from a symmetrical hub, an analytic solution is obtained; when this system is used for nutation decay the time constant is one order of magnitude smaller than previously achieved using non-optimal control logic. For the general case results are obtained numerically.

Bainum, P. M.↗

NASA NTRS1975

Review of NASA short-haul studies

The paper summarizes the results of NASA-conducted technological and economic studies of low, medium, and high density short-haul transportation systems. Aircraft concepts considered included CTOL, RTOL, STOL, and general aviation aircraft. For low density systems, it was found that viable air service becomes possible if city pairs are at least 100 km apart and a two-way total travel demand of at least 200 daily passengers exists. Currently available aircraft were found suitable. The medium-density study showed that a 60-passenger twin engine turbofan was the best suited aircraft. For high density systems, STOL appears to be an economically viable means of reducing noise and congestion at major hub airports. Adequate runways 914 m in length or greater either already exist or could be added to most existing major hub airports.

Kenyon, G. C.↗

NASA NTRS1976

Reel safety brake

A braking apparatus is described for a tape transport device having two stacked coaxial reels and feelers mounted in proximity to the reels for sensing the tape being wound on each reel. A device is mounted in proximity to adjacent central hubs of the reels to a simultaneously, frictionally engage both hubs and brake both reels. A mechanical actuator is coupled to both feelers and to the brake device. The brake means comprises a pair of rubber shoulders that extend in opposite directions relative to a common axis, and turns about the axis in response to either of the feelers.

Carle, C. E.↗

NASA NTRS1977

Analysis of internal flow of J85-13 multistage compressor

Interstage data recorded on a J85-13 engine were used to analyze the internal flow of the compressor. Measured pressures and temperatures were used as input to a streamline analysis program to calculate the velocity diagrams at the inlet and outlet of each blade row. From the velocity diagrams and blade geometry, selected blade-element performance parameters were calculated. From the detailed analysis it is concluded that the compressor is probably hub critical (stall initiates at the hub) in the latter stages for the design speed conditions. As a result, the casing treatment over the blade tips has little or no effect on stall margin at design speed. Radial inlet distortion did not appear to change the flow in the stages that control stall because of the rapid attenuation of the distortion within the compressor.

Hager, R. D.↗

NASA NTRS1977

The dynamics and optimal control of spinning spacecraft and movable telescoping appendages, part B: Effect of gravity-gradient torques on the dynamics of a spinning spacecraft with telescoping appendages

The effects of gravity gradient torques during boom deployment maneuvers of a spinning spacecraft are examined. Configurations where the booms extended only along the hub principal axes and where one or two booms are offset from the principal axes were considered. For the special case of symmetric deployment (principal axes booms) the stability boundaries are determined, and a stability chart is used to study the system behavior. Possible cases of instability during this type of maneuver are identified. In the second configuration an expression for gravity torque about the hub center of mass was developed. The nonlinear equations of motion are solved numerically, and the substantial influence of the gravity torque during asymmetric deployment maneuvers is indicated.

Bainum, P. M.↗

NASA NTRS1977

The dynamics and optimal control of spinning spacecraft with movable telescoping appendages. Part C: Effect of flexibility during boom deployment

The dynamics of a spinning symmetrical spacecraft system during the deployment (or retraction) of flexible boom-type appendages were investigated. The effect of flexibility during boom deployment is treated by modelling the deployable members as compound spherical pendula of varying length (according to a control law). The orientation of the flexible booms with respect to the hub, is described by a sequence of two Euler angles. The boom members contain a flexural stiffness which can be related to an assumed effective restoring linear spring constant, and structural damping which effects the entire system. Linearized equations of motion for this system, when the boom length is constant, involve periodic coefficients with the frequency of the hub spin. A bounded transformation is found which converts this system into a kinematically equivalent one involving only constant coefficients.

Bainum, P. M.↗

NASA NTRS1976

Optimal control of spin-stabilized spacecraft with telescoping appendages

The control of a spin-stabilized spacecraft consisting of a rigid central hub and one or two movable offset telescoping booms (with end masses) is considered. The equations of rotational motion are linearized about either of two desired final states. A control law for the boom end mass position is sought such that a quadratic cost functional involving the weighted components of angular velocity plus the control is minimized when the final time is unspecified and involves the solution of the matrix Riccati algebraic equation. For three axis control more than one offset boom (orthogonal to each other) is required. For two-axis control with a single boom offset from a symmetrical hub, an analytic solution is obtained; when this system is used for nutation decay the time constant is one order of magnitude smaller than previously achieved using nonoptimal control logic. For the general case results are obtained numerically.

Bainum, P. M.↗

NASA NTRS1978

ATS-6 flight accelerometers

Five accelerometers mounted near the adapter base of the Titan 3-C launch vehicle and three on the hub of the ATS-F spacecraft provided (1) data for verifying basic spacecraft mode shapes and frequencies during powered flight while attached to the launch vehicle; (2) failure mode detection and diagnostic information on in-flight anomalies; and (3) data to be used in the design of future spacecraft to be flown on the Titan 3-C. Because data from the instruments mounted on the spacecraft hub passed through an in-flight disconnect at the separation plane between the transtage and ATS-F, the moment this connector was broken, the signal to the telemetry system showed a step function change. By monitoring these telemetry traces on the ground at appropriate times during flight sequences, a positive indication of spacecraft separation was obtained. Flight data showing dynamic response at spacecraft launch vehicle interface and at the top of ATS spacecraft during significant launch events are presented in tables.

Mattson, R.↗

NASA NTRS1977

Effect of gravity-gradient torques on the dynamics of a spinning spacecraft with telescoping appendages

The effects of gravity-gradient torques during boom deployment maneuvers of a spinning spacecraft are examined with a combination of numerical and analytical methods. It is assumed that the spacecraft consists of a rigid central hub and movable rigid telescoping booms where the booms extend only along the hub principal axes. For the special case of symmetric deployment the stability boundaries are determined and a stability chart is used to study the system behavior. Possible cases of instability during this type of maneuver are identified.

Rajan, M.↗

NASA NTRS1978

On the shear pumping effect in rocket pump inducers

The momentum exchange between the fluid and the rotor via the shear stress in a rocket pump inducer is termed the shear pumping effect. This effect is investigated analytically in order to estimate the direct effect of shear stress in providing a head rise. An inducer with flat plates and one with cambered blades are considered. It is shown that the head rise coefficient and the relative velocities predicted from the theoretical analysis, based on momentum integral technique, seem to agree well with the measured data for a flat-plate inducer operated with open throttle and a cambered-blade inducer operated at a flow coefficient of 0.065. In particular, the flat-plate and the cambered-blade inducers have nearly the same performance, except for the axial velocity distribution. The former shows a tendency to separate in the hub region near the trailing edge, while the latter does not. Even far downstream, the flat-plate inducer has a larger separated zone near the hub.

Lakshminarayana, B.↗

NASA NTRS1978

Application of higher harmonic blade feathering for helicopter vibration reduction

Higher harmonic blade feathering for helicopter vibration reduction is considered. Recent wind tunnel tests confirmed the effectiveness of higher harmonic control in reducing articulated rotor vibratory hub loads. Several predictive analyses developed in support of the NASA program were shown to be capable of calculating single harmonic control inputs required to minimize a single 4P hub response. In addition, a multiple-input, multiple-output harmonic control predictive analysis was developed. All techniques developed thus far obtain a solution by extracting empirical transfer functions from sampled data. Algorithm data sampling and processing requirements are minimal to encourage adaptive control system application of such techniques in a flight environment.

Powers, R. W.↗

NASA NTRS1979

Experimental measurements of the rotating frequencies and mode shapes of a full scale helicopter rotor in a vacuum and correlations with calculated results

This paper presents results of an experimental program conducted to obtain data which can be used for correlations of rotor blade dynamic analyses. Measurements were made of the rotating frequencies and mode shapes of a representative full-scale, two-bladed helicopter rotor in a vacuum. The blades were cantilevered to the hub. Mode shape data were obtained optically using a system of cameras developed specifically for this purpose. Excitation of the rotor was provided by vertical oscillatory motion of the hub. To compare experimental and analytical results, correlations of some experimental measurements with calculations from an existing blade modes computer program based on a Holzer-Myklestad procedure are presented, and the differences between the results are discussed. The experimental and analytical natural frequencies were generally in good agreement as were the principal components of the modal deflections for the flap and lag modes. The torsion mode shape indicated disagreement between the measured and calculated results in regard to the amount of flap and lag motions present in this mode, while the spanwise variations of the measured and calculated torsional components were in agreement.

Lee, B. L.↗

NASA NTRS1980

Teetered, tip-controlled rotor: Preliminary test results from Mod-0 100-kW experimental wind turbine

Results of tests conducted using the MOD-0 100 kW experimental wind turbine are evaluated. The teetered rotor significantly decreased loads on the yaw drive mechanism and reduced blade cyclic flapwise bending moments by 25 percent at the 20 percent span location when compared to the rigid hub rotor. The teetered hub performed well, but impacted the teeter stops on occasion as wind speed and/or direction varied rapidly. The tip-controlled rotor performed satisfactorily with some expected loss of control when compared to the full span pitchable blade. The performance results indicate that a review of techniques used to calculate rotor power is in order.

Glasgow, J. C.↗

NASA NTRS1980

Bifilar analysis study, volume 1

A coupled rotor/bifilar/airframe analysis was developed and utilized to study the dynamic characteristics of the centrifugally tuned, rotor-hub-mounted, bifilar vibration absorber. The analysis contains the major components that impact the bifilar absorber performance, namely, an elastic rotor with hover aerodynamics, a flexible fuselage, and nonlinear individual degrees of freedom for each bifilar mass. Airspeed, rotor speed, bifilar mass and tuning variations are considered. The performance of the bifilar absorber is shown to be a function of its basic parameters: dynamic mass, damping and tuning, as well as the impedance of the rotor hub. The effect of the dissimilar responses of the individual bifilar masses which are caused by tolerance induced mass, damping and tuning variations is also examined.

Miao, W.↗

NASA NTRS1980

Effects of rotor parameter variations on handling qualities of unaugmented helicopters in simulated terrain flight

A coordinated analysis and ground simulator experiment was performed to investigate the effects on single rotor helicopter handling qualities of systematic variations in the main rotor hinge restraint, hub hinge offset, pitch-flap coupling, and blade lock number. Teetering rotor, articulated rotor, and hingeless rotor helicopters were evaluated by research pilots in special low level flying tasks involving obstacle avoidance at 60 to 100 knots airspeed. The results of the experiment are in the form of pilot ratings, pilot commentary, and some objective performance measures. Criteria for damping and sensitivity are reexamined when combined with the additional factors of cross coupling due to pitch and roll rates, pitch coupling with collective pitch, and longitudinal static stability. Ratings obtained with and without motion are compared. Acceptable flying qualities were obtained within each rotor type by suitable adjustment of the hub parameters, however, pure teetering rotors were found to lack control power for the tasks. A limit for the coupling parameter L sub q/L sub p of 0.35 is suggested.

Talbot, P. D.↗

NASA NTRS1980

Teetered, tip-controlled rotor - Preliminary test results from Mod-O 100-kW experimental wind turbine

A series of tests is currently being conducted using the DOE/NASA 100 kW Experimental Wind Turbine with a two-bladed, teetered rotor with 30% span tip control. Preliminary evaluation test results indicates that the teetered rotor significantly decreases loads on the yaw drive mechanism and reduces blade cyclic flapwise bending moments by 25% at the 20% span location when compared to rigid hub rotor. The teetered hub performed well but did impact the teeter stops on occasion as wind speed and/or direction varied rapidly. The tip-controlled rotor performed satisfactorily with some expected loss of control when compared to the full span pitchable blade. The performance results indicate that a review of techniques used to calculate rotor power is in order.

Glasgow, J. C.↗