Search NASA⌕ Search

SEARCH · Search NASA

Results for “INTERMETALLIC COMPOUNDS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Effects of high temperature treatment on microstructure and mechanical properties of laser-clad NiCrBSi/WC coatings on titanium alloy substrate

Laser-clad composite coatings on the Ti6Al4V substrate were heat-treated at 700, 800, and 900 °C for 1 h. The effects of post-heat treatment on the microstructure, microhardness, and fracture toughness of the coatings were investigated by scanning electron microscopy, X-ray diffractometry, energy dispersive spectroscopy, and optical microscopy. The wear resistance of the coatings was evaluated under dry reciprocating sliding friction at room temperature. The coatings mainly comprised some coarse gray blocky (W,Ti)C particles accompanied by the fine white WC particles, a large number of black TiC cellular/dendrites, and the matrix composed of NiTi and Ni{sub 3}Ti; some unknown rich Ni- and Ti-rich particles with sizes ranging from 10 nm to 50 nm were precipitated and uniformly distributed in the Ni{sub 3}Ti phase to form a thin granular layer after heat treatment at 700 °C. The granular layer spread from the edge toward the center of the Ni{sub 3}Ti phase with increasing temperature. A large number of fine equiaxed Cr{sub 23}C{sub 6} particles with 0.2–0.5 μm sizes were observed around the edges of the NiTi supersaturated solid solution when the temperature was further increased to 900 °C. The microhardness and fracture toughness of the coatings were improved with increased temperature due to the dispersion-strengthening effect of the precipitates. Dominant wear mechanisms for all the coatings included abrasive and delamination wear. The post-heat treatment not only reduced wear volume and friction coefficient, but also decreased cracking susceptibility during sliding friction. Comparatively speaking, the heat-treated coating at 900 °C presented the most excellent wear resistance. - Highlights: • TiC + WC reinforced intermetallic compound matrix composite coatings were produced. • The formation mechanism of the reinforcements was analyzed. • Two precipitates were generated at elevated temperature. • Cracking susceptibility and microhardness of the coatings were improved. • Post-heat treatment enhances wear resistance of the coatings.

36 MATERIALS SCIENCE↗

Characterization of Interaction Layer in U-Mo-X (X = Nb, Zr) and U-Nb-Zr vs. Al Diffusion Couples Annealed at 600 Degrees C for 10 Hours

U-Mo has thus far proven to be one of the most feasible metallic fuel alloys for use in research and test reactors due to its high density and stability during irradiation. However, an adverse diffusional interaction can occur between the fuel alloy and the Al based matrix. This forms an interaction layer (IL) that has undesirable thermal properties and irradiation behavior leading to accelerated swelling and reduced fuel efficiency. This study focused on the effects of ternary alloying additions on the formation of IL between U based alloys and Al. Diffusion couples of U-8Mo-3Nb, U-7Mo-6Zr, and U-10Nb-4Zr (wt.%) vs. pure Al were assembled and annealed at 600 Degrees C for 10 hours. Both thickness and phase constituent analyses were performed via electron microscopy. The major phase constituent of the IL was determined to be the UAl3 intermetallic compound. The Nb and Zr alloying additions did not reduce growth rate of IL (1.3-1.4 {mu}m/sec1/2) as compared to couples made between binary U-Mo and Al (0.9-1.8 {mu}m/sec1/2).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Effect of heat input on the microstructure, residual stresses and corrosion resistance of 304L austenitic stainless steel weldments

Austenitic stainless steels are widely used in high performance pressure vessels, nuclear, chemical, process and medical industry due to their very good corrosion resistance and superior mechanical properties. However, austenitic stainless steels are prone to sensitization when subjected to higher temperatures (673 K to 1173 K) during the manufacturing process (e.g. welding) and/or certain applications (e.g. pressure vessels). During sensitization, chromium in the matrix precipitates out as carbides and intermetallic compounds (sigma, chi and Laves phases) decreasing the corrosion resistance and mechanical properties. In the present investigation, 304L austenitic stainless steel was subjected to different heat inputs by shielded metal arc welding process using a standard 308L electrode. The microstructural developments were characterized by using optical microscopy and electron backscattered diffraction, while the residual stresses were measured by X-ray diffraction using the sin{sup 2}ψ method. It was observed that even at the highest heat input, shielded metal arc welding process does not result in significant precipitation of carbides or intermetallic phases. The ferrite content and grain size increased with increase in heat input. The grain size variation in the fusion zone/heat affected zone was not effectively captured by optical microscopy. This study shows that electron backscattered diffraction is necessary to bring out changes in the grain size quantitatively in the fusion zone/heat affected zone as it can consider twin boundaries as a part of grain in the calculation of grain size. The residual stresses were compressive in nature for the lowest heat input, while they were tensile at the highest heat input near the weld bead. The significant feature of the welded region and the base metal was the presence of a very strong texture. The texture in the heat affected zone was almost random. - Highlights: • Effect of heat input on microstructure, residual stresses and corrosion is studied. • HAZ and width of dendrite in the welded region increase with heat input. • Residual stresses are tensile near the welded region after the highest heat input. • Welded region has the highest pit density after highest heat input. • Dendrites and δ-ferrite were highly oriented in the welded region.

36 MATERIALS SCIENCE↗

Microstructural Investigations On Ni-Ta-Al Ternary Alloys

The Ni-Al-Ta ternary alloys in the Ni-rich part present complex microstructures. They are composed of multiple phases that are formed according to the nominal composition of the alloy, primary Ni(gamma), Ni{sub 3}Al(gamma'), Ni{sub 6}AlTa(tau{sub 3}), Ni{sub 3}Ta(delta) or in equilibrium: two solid phases (gamma'-tau{sub 3}), (tau{sub 3}-delta), (tau{sub 3}-gamma), (gamma-delta) or three solid phases (gamma'-tau{sub 3}-delta). The nature and the volume fraction of these phases give these alloys very interesting properties at high temperature, and this makes them attractive for specific applications. We have developed a series of ternary alloys in electric arc furnace, determining their solidification sequences using Differential Thermal Analysis (DTA), characterized by SEM-EDS, X-ray diffraction and by a microhardness tests. The follow-up results made it possible to make a correlation between the nature of the formed phases and their solidifying way into the Ni{sub 75}Al{sub x}Ta{sub y} (x+y = 25at.%) system, which are varied and complex. In addition to the solid solution Ni (gamma), the formed intermetallics compounds (gamma', tau{sub 3} and delta) has been identified and correlated with a complex balance between phases.We noticed that the hardness increases with the tantalum which has a hardening effect and though the compound Ni{sub 3}Ta(delta) is the hardest. The below results provide a better understanding of the complex microstructure of these alloys.

36 MATERIALS SCIENCE↗

The interfacial amorphous double layer and the homogeneous nucleation in reflow of a Sn-Zn solder on Cu substrate

To illustrate the interfacial reaction mechanism, the Sn-Zn[Sn-8.5Zn-0.5Ag-0.01Al-0.1Ga (wt%)] solder was reflowed on Cu substrate at 250 deg. C for 15 s followed by immediate quench in liquid nitrogen. The frozen interfacial microstructure was investigated with high resolution transmission electron microscope. An amorphous double layer was formed at the interface which consists of a 5 nm pure Cu region and a Cu-Zn diffusion region. Nanocrystalline intermetallic compound (IMC) Cu{sub 5}Zn{sub 8} were observed in the Cu-Zn diffusion region. These nanocrystalline IMCs are suggested to form via a homogeneous nucleation process.

36 MATERIALS SCIENCE↗

Cr3 Triangles induced competing magnetic interactions in the new metal boride TiCrIr2B2: An NMR and DFT study

Highlights: • One-dimensional trigonal arrangements of chromium atoms (Cr{sub 3}) was found in TiCrIr{sub 2}B{sub 2}. • Competing weak ferromagnetic and strong antiferromagnetic interactions support an itinerant d-band character for TiCrIr{sub 2}B{sub 2}. • Spin-polarized and non-spin-polarized DOS results for TiCrIr{sub 2}B{sub 2} unveil an electronic instability and the presence of a pseudogap at E{sub F}, respectively. - Abstract: The presence of one-dimensional trigonal arrangements of chromium atoms (Cr{sub 3}) in the structure of TiCrIr{sub 2}B{sub 2} leads to a magnetic transition near ambient temperature. Herein we report an investigation of the nature of electronic and magnetic properties of TiCrIr{sub 2}B{sub 2} via ab initio calculations together with {sup 11}B NMR Knight shift (K) and spin-lattice relaxation rate (1/T{sub 1}) analysis. The presence of a characteristic rectangular powder pattern below 280 K, absence of a Korringa relation, strong enhancement of 1/T{sub 1}.T at low temperatures and weak temperature dependence of K indicate competition between antiferromagnetic and ferromagnetic spin fluctuations in the itinerant d-band electrons, in agreement with ab initio calculations. One-dimensional trigonal arrangements of magnetically active elements in intermetallic compounds, as is found in TiCrIr{sub 2}B{sub 2}, are quite rare and could lead to exotic phenomena such as spin-chirality and quantum criticality in low-dimensional frustrated lattices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Advances in Modeling Exploding Bridgewire Initiation

There is great interest in applying magnetohydrodynamic (MHD) simulation techniques to the designs of electrical high explosive (HE) initiators, for the purpose of better understanding a design's sensitivities, optimizing its performance, and/or predicting its useful lifetime. Two MHD-capable LLNL codes, CALE and ALE3D, are being used to simulate the process of ohmic heating, vaporization, and plasma formation in exploding bridgewires (EBW). Initiation of the HE is simulated using Ignition & Growth reactive flow models. 1-D, 2-D and 3-D models have been constructed and studied. The models provide some intuitive explanation of the initiation process and are useful for evaluating the potential impact of identified aging mechanisms (such as the growth of intermetallic compounds or powder sintering). The end product of this work is a simulation capability for evaluating margin in proposed, modified or aged initiation system designs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Inhibiting Brittle Intermetallic Layer in Magnesium/Aluminum Bimetallic Castings via In Situ Formation of Mg{sub 2}Si Phase

A quasi-continuous Mg{sub 2}Si layer is formed in situ at the magnesium/aluminum interface of bimetallic castings, by selecting a Si-containing aluminum alloy and overcasting process control. This effectively inhibits the formation of brittle intermetallic compounds (Al{sub 3}Mg{sub 2}, Al{sub 12}Mg{sub 17}) during the casting process, and the mechanisms are discussed based on phase diagram calculations and experimental validation. It is, thus, recommended to select Si-containing Al alloys as substrate for Mg/Al bimetallic castings.

36 MATERIALS SCIENCE↗

Effect of Localized Corrosion on Fatigue–Crack Growth in 2524-T3 and 2198-T851 Aluminum Alloys Used as Aircraft Materials

Corrosion and fatigue of aluminum alloys are major issues for the in-service life assessment of aircraft structures and for the management of aging air fleets. The aim of this work was to evaluate the effect of localized corrosion on fatigue crack growth (FCG) resistance of the AA2198-T851 Al-Li alloy (Solution Heat Treated, Cold Worked, and Artificially Aged), comparing it with the FCG resistance of AA2524-T3 (Solution Heat Treated and Cold Worked), considering the effect of seawater fog environment. Before fatigue tests, the corrosion behavior of 2198-T851 and 2524-T3 aluminum alloys was verified using open circuit potential and potentiodynamic polarization techniques. Fatigue in air and corrosion fatigue tests were performed applying a stress ratio (R) of 0.1, 15 Hz (air) and 0.1 Hz (seawater fog) frequencies, using a sinusoidal waveform in all cases. The results showed that the localized characteristics of the 2198-T851 and 2524-T3 aluminum alloys are essentially related to the existence of intermetallic compounds, which, due to their different nature, may be cathodic or anodic in relation to the aluminum matrix. The corrosive medium has affected the FCG rate of both aluminum alloys, in a quite similar way. Graphical Abstract: .

36 MATERIALS SCIENCE↗

Crystal structure and high-pressure studies of WAl{sub 2}, an aluminide crystallizing with the CrSi{sub 2} structure type

The novel intermetallic compound WAl{sub 2} crystallizes with space group P6{sub 4}22 and lattice parameters a=4.7422(1) A, c=6.6057(2) A. The crystal structure was solved from single-crystal X-ray diffraction data. WAl{sub 2} was found to be the first aluminide that is isotypic with CrSi{sub 2}. A high-pressure powder X-ray diffraction study showed its stability up to at least 31.5(1) GPa. The bulk modulus was calculated by fitting a third-order Birch-Murnaghan equation of state to the pressure-volume data as K{sub 0}=168(11) GPa and its pressure derivative K'=7.7(1.0). Partially covalent bonding between W and Al atoms was indicated by means of the electron localization function (ELF) and explains the anisotropic compression behavior. Quantum chemical calculations identify WAl{sub 2} as a potential high-temperature phase. - Graphical abstract: The novel compound WAl{sub 2} is the first aluminide crystallizing with the CrSi{sub 2} structure type. This compound is stable up to high pressures of at least 31.5 GPa. The chemical bonding analysis by means of the electron localization function (ELF) reveals a partially covalent bonding being responsible for the anisotropic compression behavior.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterization of intermetallics in aluminum to zinc coated interstitial free steel joining by pulsed MIG brazing for automotive application

In order to meet the demand for lighter and more fuel efficient vehicles, a significant attempt is currently being focused toward the substitution of aluminum for steel in the car body structure. It generates vital challenge with respect to the methods of joining to be used for fabrication. However, the conventional fusion joining has its own difficulty owing to formation of the brittle intermetallic phases. In this present study AA6061-T6 of 2 mm and HIF-GA steel sheet of 1 mm thick are metal inert gas (MIG) brazed with 0.8 mm Al–5Si filler wire under three different heat inputs. The effect of the heat inputs on bead geometry, microstructure and joint properties of MIG brazed Al-steel joints were exclusively studied and characterized by X-ray diffraction, field emission scanning electron microscopy (FESEM), electron probe micro analyzer (EPMA) and high resolution transmission electron microscopy (HRTEM) assisted X-ray spectroscopy (EDS) and selective area diffraction pattern. Finally microstructures were correlated with the performance of the joint. Diffusion induced intermetallic thickness measured by FESEM image and concentration profile agreed well with the numerically calculated one. HRTEM assisted EDS study was used to identify the large size FeAl{sub 3} and small size Fe{sub 2}Al{sub 5} type intermetallic compounds at the interface. The growth of these two phases in A2 (heat input: 182 J mm{sup −1}) is attributed to the slower cooling rate with higher diffusion time (~ 61 s) along the interface in comparison to the same for A1 (heat input: 155 J mm{sup −1}) with faster cooling rate and shorter diffusion time (~ 24 s). The joint efficiency as high as 65% of steel base metal is achieved for A2 which is the optimized parameter in the present study. - Highlights: • AA 6061 and HIF-GA could be successfully joined by MIG brazing. • Intermetallics are exclusively studied and characterized by XRD, FESEM and EPMA. • Intermetallic formation by diffusion is worth considering or not. • HRTEM-EDS, SAD pattern identifies the morphologies and size of intermetallics. • A compromise concerning formation of IMC is necessary.

36 MATERIALS SCIENCE↗

Interfacial microstructure evolution and weld formation during ultrasonic welding of Al alloy to Cu

Highlights: • Surface oxide layer was fractured and dispersed around the weld interface during ultrasonic welding of Al alloy to Cu. • Mechanical mixing around the weld interface was caused by compressive deformation with ultrasonic vibration. • Once micro-bonds were generated between Al and Cu, shear deformation occurred around the weld interface. • Enhanced Cu diffusion into Al in the severely deformed region significantly contributed to the weld formation. - Abstract: Dissimilar welds of Al alloy 1050 to Cu were prepared via ultrasonic spot welding in order to understand the formation of welds and interfacial microstructures. To observe oxide layer behavior at the weld interface, the anodized Al alloy 1050 was also welded to Cu. Mechanical mixing and material flow during ultrasonic welding broke and dispersed the oxide layers into the Al matrix. This material flow is attributed to compressive deformation that occurred due to ultrasonic vibrations. Direct bonding in the Al/Cu region increased with welding time. Once micro-bonds were generated between Al and Cu, the Al matrix in the vicinity of the weld interface was severely deformed in the direction of the ultrasonic vibrations. Consequently, a recrystallized microstructure with shear texture was formed in the Al matrix. Deformation heating and severe shear deformation formed Al{sub 2}Cu intermetallic compound layers at the weld interface. The growth rate of the Al{sub 2}Cu layer was much faster than had previously been estimated based upon the peak temperature and ultrasonic welding heating time. This is likely due to the increased rate of Cu diffusion into Al in the severely deformed region.

36 MATERIALS SCIENCE↗

Metal-rich phosphides RE{sub 5}Ir{sub 19}P{sub 12} with Sc{sub 5}Co{sub 19}P{sub 12} type structure

The iridium-rich phosphides RE{sub 5}Ir{sub 19}P{sub 12} (RE=Sc, Y, La-Nd, Sm-Lu) with Sc{sub 5}Co{sub 19}P{sub 12} type structure, space group P62-bar m were synthesized by solid state reactions of the elements in tantalum crucibles. Well shaped single crystals were obtained in bismuth fluxes. All phosphides were characterized on the basis of X-ray powder data. The structures of RE{sub 5}Ir{sub 19}P{sub 12} with RE=Sc, La, Ce, Dy, Er, Tm, and Yb were refined from single crystal diffractometer data. The complex structure of these phosphides can be described by an intergrowth of simpler ThCr{sub 2}Si{sub 2} and SrPtSb related slabs. Striking structural motifs of the RE{sub 5}Ir{sub 19}P{sub 12} structures are slightly distorted tricapped trigonal prisms of the metal atoms around the phosphorus atoms. The iridium and phosphorus atoms build up three-dimensional [Ir{sub 19}P{sub 12}] polyanionic networks (230-286 pm Ir-P and 282-296 pm Ir-Ir in La{sub 5}Ir{sub 19}P{sub 12}) which leave cavities of coordination numbers 16 and 15 for the rare earth atoms. - Graphical Abstract: The intergrowth structure La{sub 5}Ir{sub 19}P{sub 12}. Highlights: > Metal flux syntheses of intermetallic compounds. > Synthesis and structure of new phosphides RE{sub 5}Ir{sub 19}P{sub 12}. > Crystal chemistry of metal-rich phosphides. > Description of the RE{sub 5}Ir{sub 19}P{sub 12} structure as an intergrowth variant.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microstructural characterization and dry sliding wear resistance of MoO{sub 2}-strengthened {gamma}/NiMo alloys with different primary phases

Two {gamma}/NiMo alloys strengthened by a refractory metal oxide MoO{sub 2} phase were fabricated by a laser melting deposition process. Microstructural transformation of the alloys with different primary phases was identified and the crystal structure of the primary phases was confirmed by both X-ray diffraction and transmission electron microscopy. Meanwhile, room-temperature dry sliding wear behavior and mechanism difference of the alloys were also investigated mainly by scanning electron microscopy. Microstructures of the alloys varied from hypoeutectic to hypereutectic, as the molybdenum content increases. The hypoeutectic alloy was solidified on the basis of a Ni-base solid solution {gamma} primary phase, whereas the hypereutectic alloy was grown based on an intermetallic compound with NiMo primary phase. The {gamma}, NiMo primary phases and MoO{sub 2} strengthening phase were confirmed to have face-centered cubic, orthorhombic and monoclinic structures, respectively. Compared with the hypoeutectic alloy, the hypereutectic alloy exhibited higher wear resistance under the same condition. The predominant wear mechanism of the {gamma}/NiMo alloys transformed from micro-cutting to microcracking.

36 MATERIALS SCIENCE↗

Study of the magnetic properties, structure, and phase transformation in the alloys of the Co-Al-W system

An experimental study of phase transformations in the system of Co-Al-W in the concentration area of the intermetallic compound Co{sub 3}(Al, W) is presented. The structure and phase composition of the Co–9 at % Al–X at % W (X = 4.5, 6.8, 8.5, 10, 12.5) alloys in depending on the tungsten content are analyzed. The Curie temperature and magnetic properties of the alloys with the different phase composition are determined.

36 MATERIALS SCIENCE↗

Charge-induced atomic strain as a predictor of structural phase transformation in rare-earth intermetallics

We present a descriptor based on charge-induced atomic strain in crystalline lattices for predicting structural phase transformations in rare-earth intermetallic compounds containing lanthanides and transition metals. The charge-induced local atomic strain was obtained from structural optimization of experimentally known crystalline phases using state of the art density-functional theory methods. The predictive power of the descriptor was evaluated on 𝑅⁢𝐸 2 ⁢In (𝑅𝐸 = rare earth) compounds, a class known for diverse phase transformations. We show that incorporating quantum-mechanical effects—such as local charge distribution, bonding, symmetry, and electronic structure—enhances the robustness of the descriptor. To gain further insight, we analyzed phononic and electronic behavior in Y 2 ⁢In and demonstrated that experimental phase transformations are captured only when atomic strain effects are included. The descriptor was further used to predict structural phase changes in (Y⁢b 1–𝑥 ⁢E⁢r 𝑥 ) 2 ⁢In and G⁡d 2 ⁡(I⁢n 1–𝑥⁢ A⁢l 𝑥 ), with predictions confirmed by x-ray powder diffraction. Here, while the current study is focused on lanthanide-based intermetallics, the underlying principles of the descriptor suggest potential applicability to other closely related classes of rare-earth intermetallics.

Density functional theory↗

Microstructure evolution of a dissimilar junction interface between an Al sheet and a Ni-coated Cu sheet joined by magnetic pulse welding

An Al sheet and a Ni-coated Cu sheet were lap joined by using magnetic pulse welding (MPW). Tensile tests were performed on the joined sheets, and a good lap joint was achieved at a discharge energy of > 0.9 kJ. The weld interface exhibited a wavy morphology and an intermediate layer along the weld interface. Microstructure observations of the intermediate layer revealed that the Ni coating region consisted of a Ni–Al binary amorphous alloy and that the Al sheet region contained very fine Al nanograins. Ni fragments indicative of unmelted residual Ni from the coating were also observed in parts of the intermediate layer. Formation of these features can be attributed to localize melting and a subsequent high rate cooling of molten Al and Ni confined to the interface during the MPW process. In the absence of an oxide film, atomic-scale bonding was also achieved between the intermediate layer and the sheet surfaces after the collision. MPW utilises impact energy, which affects the sheet surfaces. From the obtained results, good lap joint is attributed to an increased contact area, the anchor effect, work hardening, the absence of an oxide film, and suppressed formation of intermetallic compounds at the interface. - Highlights: •Good lap joint of an Al sheet and a Ni-coated Cu sheet was achieved by using magnetic pulse welding. •A Ni–Al binary amorphous alloy was formed as an intermediate layer at weld interface. •Atomic-scale bonding was achieved between the intermediate layer and the sheet surfaces.

36 MATERIALS SCIENCE↗

Anisotropic magnetic properties of Dy{sub 6}Cr{sub 4}Al{sub 43} single crystal

We have studied the anisotropic magnetic behavior of the rare earth intermetallic compound Dy{sub 6}Cr{sub 4}Al{sub 43}. This compound crystallizes in the hexagonal symmetry and orders ferromagnetically at 8.3 K as confirmed by the magnetic susceptibility and heat capacity measurements. A significant anisotropy in the magnetization is observed between the c axis and the ab-plane. The easy axis liesin theab-plane at low temperatures; however it orients itselfalong the c-axis above 170 K as inferred from the susceptibility data.

36 MATERIALS SCIENCE↗