Search NASA⌕ Search

SEARCH · Search NASA

Results for “In Situ Processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Compositional simulation of hydrocarbon recovery from oil shale reservoirs with diverse initial saturations of fluid phases by various thermal processes

We have studied the hydrocarbon production from oil shale reservoirs filled with diverse initial saturations of fluid phases by implementing numerical simulations of various thermal in-situ upgrading processes. We use our in-house fully functional, fully implicit, and non-isothermal simulator, which describes the in-situ upgrading processes and hydrocarbon recovery by multiphase-multicomponent systems. We have conducted two sets of simulation cases—five-spot well pattern problems and Shell In-situ Conversion Process (ICP) problems. In the five-spot well pattern problems, we have analyzed the effects of initial fluid phase that fills the single-phase reservoir and thermal processes by four cases—electrical heating in the single-phase-aqueous reservoir, electrical heating in the single-phase-gaseous reservoir, hot water injection in the single-phase-aqueous reservoir, and hot CO 2 -injection in the single-phase-gaseous reservoir. In the ICP problems, we have analyzed the effects of initial saturations of fluid phases that fill two-phase-aqueous-and-gaseous reservoir by three cases—initial aqueous phase saturations of 0.16, 0.44, and 0.72. Through the simulation cases, system response and production behavior including temperature profile, kerogen fraction profile, evolution of effective porosity and absolute permeability, phase production, and product selectivity are analyzed. In the five-spot well pattern problems, it is found that the hot water injection in the aqueous phase reservoir shows the highest total hydrocarbon production, but also shows the highest water-oil-mass-ratio. Productions of phases and components show very different behavior in the cases of electrical heating in the aqueous phase reservoir and the gaseous phase reservoir. In the ICP problems, it is found that the speed of kerogen decomposition is almost identical in the cases, but the production behavior of phases and components is very different. It is found that more liquid organic phase has been produced in the case with the higher initial saturation of aqueous phase by the less production of gaseous phase.

04 OIL SHALES AND TAR SANDS↗

In Situ Indexing and Query Processing of AMR Data

We have developed the first, holistic, Adaptive Mesh Refinement (AMR) capable, in situ query framework to ensure the tractability of the current- and next-generation AMR simulation analysis on the path to extreme scale. We have addressed key issues pertaining to in situ analysis, memory hierarchy, generalized parallel indexing, index-compression, and real-time access pattern detection. We have published the following research papers in high profile peer reviewed computer science conferences: (a) Parallel In Situ Detection of Connected Components in Adaptive Mesh Refinement Data; (b) AMR-aware In Situ Indexing and Scalable Querying; (c) Pattern-driven dynamic data layout optimization; (d) In situ Storage Layout Optimization for AMR Spatio-temporal Read Accesses; (e) AMRZone: A Runtime AMR Data Sharing Framework for Scientific Applications; (f) Exploring Memory Hierarchy and Network Topology for Runtime AMR Data Sharing Across Scientific Applications.

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗

A Review of Low Frequency Electromagnetic Wave Phenomena Related to Tropospheric-Ionospheric Coupling Mechanisms

Investigation of coupling mechanisms between the troposphere and the ionosphere requires a multidisciplinary approach involving several branches of atmospheric sciences, from meteorology, atmospheric chemistry, and fulminology to aeronomy, plasma physics, and space weather. In this work, we review low frequency electromagnetic wave propagation in the Earth-ionosphere cavity from a troposphere-ionosphere coupling perspective. We discuss electromagnetic wave generation, propagation, and resonance phenomena, considering atmospheric, ionospheric and magnetospheric sources, from lightning and transient luminous events at low altitude to Alfven waves and particle precipitation related to solar and magnetospheric processes. We review in situ ionospheric processes as well as surface and space weather phenomena that drive troposphere-ionosphere dynamics. Effects of aerosols, water vapor distribution, thermodynamic parameters, and cloud charge separation and electrification processes on atmospheric electricity and electromagnetic waves are reviewed. We also briefly revisit ionospheric irregularities such as spread-F and explosive spread-F, sporadic-E, traveling ionospheric disturbances, Trimpi effect, and hiss and plasma turbulence. Regarding the role of the lower boundary of the cavity, we review transient surface phenomena, including seismic activity, earthquakes, volcanic processes and dust electrification. The role of surface and atmospheric gravity waves in ionospheric dynamics is also briefly addressed. We summarize analytical and numerical tools and techniques to model low frequency electromagnetic wave propagation and solving inverse problems and summarize in a final section a few challenging subjects that are important for a better understanding of tropospheric-ionospheric coupling mechanisms.

Simoes, Fernando↗

An in situ generated polymer electrolyte via anionic ring-opening polymerization for lithium–sulfur batteries

The use of solid polymer electrolytes has previously proven to be an effective approach to address the lithium polysulfide dissolution and high electrode interfacial impedance of Li–S batteries via an in situ polymerization process. However, the conventional in situ synthesis employs a cationic ring-opening polymerization (CROP) of 1,3-dioxolane (DOL) catalyzed by a strong Lewis acid. New polymerization chemistry that is more compatible with Li–S chemistry needs to be developed to mitigate the disadvantages associated with the CROP process. Herein we report a new approach to in situ polymerize a set of new episulfide monomers in solution with LiTFSI salt via an anionic ring-opening polymerization (AROP). This new polymer system takes advantage of the inherent cell chemistry present in the Li–S cell through the nucleophilic lithium sulfides which are generated during the initial discharge cycle and act as the initiator for the polymerization. Additionally, their presence was shown to initiate the monomer solvents through AROP with no need for additional catalysts, rather than the more commonly utilized cationic systems which require an external Lewis acid catalyst. This work offers an important pathway toward in situ polymer electrolytes for Li–S batteries and offers a new avenue of exploration for polymer electrolyte synthesis.

25 ENERGY STORAGE↗

Modeling and Analysis of the Reverse Water Gas Shift Process for In-Situ Propellant Production

This report focuses on the development of mathematical models and simulation tools developed for the Reverse Water Gas Shift (RWGS) process. This process is a candidate technology for oxygen production on Mars under the In-Situ Propellant Production (ISPP) project. An analysis of the RWGS process was performed using a material balance for the system. The material balance is very complex due to the downstream separations and subsequent recycle inherent with the process. A numerical simulation was developed for the RWGS process to provide a tool for analysis and optimization of experimental hardware, which will be constructed later this year at Kennedy Space Center (KSC). Attempts to solve the material balance for the system, which can be defined by 27 nonlinear equations, initially failed. A convergence scheme was developed which led to successful solution of the material balance, however the simplified equations used for the gas separation membrane were found insufficient. Additional more rigorous models were successfully developed and solved for the membrane separation. Sample results from these models are included in this report, with recommendations for experimental work needed for model validation.

Whitlow, Jonathan E.↗

Deformation and fracture behavior of a laser powder bed fusion processed stainless steel: In situ synchrotron x-ray computed microtomography study

Tensile plastic deformation and fracture behavior of a laser powder bed fusion processed 316L stainless steel alloy was investigated in situ using high-resolution synchrotron x-ray computed microtomography (sXCT). Three different cases were studied: (1) specimen A1, near full-density with initial porosity of 0.04%, (2) specimen B1, initial lack-of-fusion (LOF) porosity of about 3% with the major axis of defects aligned nearly perpendicular to the tensile loading direction (LD), and (3) specimen B, similar to B1 but with the major axis of LOF defects aligned nearly parallel to LD. The effects of type, density, and orientation of defects in as-printed samples on plastic deformation and failure modes were studied by analyzing sXCT image sequences and quantitative defect properties. Specifically, the evolutions of porosity, size, aspect ratio, and angle of gas pores and LOF defects were characterized as a function of applied strain. Moreover, interactions between as-printed defects and deformation-induced crack propagation were investigated. The tensile behavior of specimen A1 was comparable to that of a commercial wrought plate. Furthermore, the quantitative in-situ sXCT results showed a void-growth phenomenon in A1 but without noticeable coalescence, resulting in a ductile cup-cone failure. Specimen B1 showed damage-driven brittle failure with limited plasticity due to early and rapid propagation of open voids. On the other hand, specimen B, with a similar amount of LOF defects as B1, showed deceivingly strong and ductile tensile behavior similar to A1 without any major crack propagations due to the favorable orientation relationship between LOF defects and the LD.

36 MATERIALS SCIENCE↗

In situ monitoring of material processing by a pulsed laser beam coupled via a lensed fiber into a scanning electron microscope

In this study, a new method coupling laser irradiation into a dual-beam scanning electron microscope (SEM) and focused-ion-beam (FIB) system is developed. By using a lensed fiber, pulsed laser illumination could be successfully delivered onto the sample under SEM imaging, providing in situ monitoring for laser material processing applications including local modification of micro-/nanostructures and laser-assisted chemical vapor deposition. In situ characterization of the laser-induced features by high resolution SEM imaging and energy dispersive x-ray spectrometry was successfully carried out. Furthermore, in situ repair of a contaminated lensed fiber probe during laser-assisted chemical vapor deposition was demonstrated via FIB milling. The results demonstrate the full compatibility of the lensed fiber apparatus with the dual-beam apparatus without disturbing the original functions of the system. The combination of guided laser radiation with SEM and FIB instruments offers a powerful capability for in situ monitoring of multilevel laser-based micro- and nanoscale material processing.

36 MATERIALS SCIENCE↗

Long Lived Charge Separated States Induced by trans-Stilbene Incorporation in the Pores of Brønsted Acidic HZSM-5 Zeolites: Effect of Gallium on the Spontaneous Ionization Process

In situ CW-EPR, diffuse reflectance UV-visible spectroscopy and Raman scattering were used to monitor the spontaneous incorporation of trans-stilbene (t-St, C{sub 14}H{sub 12}) in the medium pore H{sub 2.2}-GaZSM-5 zeolites [H{sub 2.2}(GaO{sub 2}){sub 2.2}(SiO{sub 2}){sub 93.8}] by direct exposure under dry and inert atmosphere of solid t-St to dehydrated porous material without any solvent. The sorption of t-St with relatively low ionization potential (7.65 eV) occurs in Broensted acidic H{sub 2.2}-GaZSM-5 zeolites according to a complex and slow reaction sequence. First, charge separation occurs and t-St{sup {sm_bullet}+}{at}H{sub 2.2}-GaZSM-5{sup {sm_bullet}-} radical pair is created, while long-lived t-St{at}H{sub 2.2}GaZSM-5{sup {sm_bullet}-{sm_bullet}+} electron-hole pair is formed through hole transfer. The analysis of the DRUVv spectra set recorded during the t-St sorption course shows the respective concentrations of all transient species as a function of time. In particular, note that system reorganization is observed through a second type of electron-hole pair. The broad and strong bands observed in the near-IR regions over extended periods of time are tentatively assigned to the electron and/or hole spectral signatures in slightly different environments. Applying pulsed X-band EPR techniques, we were able to reveal the structural surrounding of the unpaired electrons of charge-separated states through the proper assignment of electron couplings with a large number of nuclei such as {sup 1}H, {sup 29}Si, {sup 69}Ga, and {sup 71}Ga using the two-dimensional hyperfine-sublevel correlation experiment (2D-HYSCORE). The distance measurements deduced from dipolar coupling experiments provide a unique picture of the long distance distribution of unpaired electrons generated by spontaneous ionization of t-St upon incorporation within H{sub 2.2}-GaZSM-5 zeolite. This result demonstrates that a large fraction of the unpaired electrons are ejected away from the initial site of ionization and that this compartmentalization plus the created electrostatic field hinder dramatically the propensity of charge recombination. The results for H-GaZSM-5 are compared to similar experiments conducted on H-AlZSM-5 zeolites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Homogeneous CuGaSe 2 growth by the CuPRO process with In-Situ AgBr treatment

Homogeneous CuGaSe 2 thin film growth is limited by slow kinetics of formation. A modified growth process was previously developed to address this issue but requires two separate long, high temperature anneals. Here, we demonstrate that a short AgBr treatment can replace this modified growth process. The AgBr works as a transport agent to catalyze CuGaSe 2 formation and atomic mobility. Furthermore, this treatment results in large grains with homogeneous composition through the bulk. Solar cells made with this material show better performance.

14 SOLAR ENERGY↗

Controlling the spatio-temporal dose distribution during STEM imaging by subsampled acquisition: In-situ observations of kinetic processes in liquids

Subsampled image acquisition followed by image inpainting in the scanning transmission electron microscope (STEM) is a novel approach to control dose and increase the image frame rate during experiments, thereby allowing independent control of the spatial and temporal dose envelope during image acquisition. Here, subsampled imaging is shown to permit precise in-situ observations of the fundamental kinetic processes behind nucleation and growth of silver (Ag) nanoparticles from an aqueous solution. At high sampling-levels, nanoparticles can be observed with morphologies that are consistent with strong interface interactions, i.e. rafts and pillars, whereas at low sampling-levels, the particles exhibit regular spherical morphologies. The relative numbers of rafts/pillars and regular nanoparticles, their sizes and their incubation times can be attributed to local changes in the molar concentration of the Ag ions in the aqueous solution; higher sampling-levels significantly increase the reactants in the vicinity of the window, leading to rapid supersaturation and the precipitation on the window surface. These precisely controlled kinetics highlight subsampled imaging as a method by which the driving force for nucleation and growth (i.e the electron beam) can be disentangled from the spatial/temporal resolution of the observation in all in-situ experiments, providing a pathway to identify and quantify the importance of individual kinetic factors behind nucleation and growth in a wide variety of complex materialssystems and architectures.

74 ATOMIC AND MOLECULAR PHYSICS↗

In situ Resource Utilization for Processing of Metal Alloys on Lunar and Mars Bases

Current plans for practical missions leading to a sustained human presence on our Moon and Mars rely on utilizing their in situ resources. Initially, resource availability must be assessed followed by the development of economically acceptable and technically feasible extractive processes. In regard to metals processing and fabrication, the lower gravity level on the Moon (0.125 g) and Mars (0.369 g) will dramatically change the presently accepted hierarchy of materials in terms of specific properties, a factor which must be understood and exploited. Furthermore, significant changes are expected in the behavior of liquid metals during processing. In metal casting, for example, mold filling and associated solidification processes have to be reevaluated. Finally, microstructural development and therefore material properties, presently being documented through ongoing research in microgravity science and applications, needs to be understood and scaled to the reduced gravity environments. These and other issues are addressed in this paper.

Stefanescu, D. M.↗

Investigating Powder Spreading Dynamics in Additive Manufacturing Processes by In-situ High-speed X-ray Imaging

The quality of the powder bed is known to be one of the main factors that influence the quality of the part being manufactured by powderbed- based additive manufacturing processes. For example, in the laser powder bed fusion process, it has been demonstrated that improving the powder bed density and homogeneity improves the final quality of the part. Understanding powder spreading dynamics in the powder-bed-based additive manufacturing processes is critical for designing spreading structures and spreading parameters, identifying defect formation mechanisms in the powder bed, and guiding the design of optimized feedstock powders. Extensive efforts have been devoted to understand the fundamental mechanism of the powder flow and spreading process. Various powder flow testers were used to study the flow behavior of powders used in additive manufacturing. However, the powder flow conditions in flow meters are different from those in real additive manufacturing conditions. Models have also been developed to simulate and study the spreading process. The discrete element method (DEM) is currently the main tool for computationally simulating the spreading process. However, these models are based on many physical assumptions. Visible light cameras have been used recently to conduct in-situ study of powder spreading in additive manufacturing. Due to the limited resolution and penetration depth of visible light, it is extremely difficulty to study the particle-scale powder spreading dynamics. Here, to overcome the challenges of studying powder spreading dynamics under real additive manufacturing conditions, we developed an experimental approach to study the particle-scale powder spreading process with high spatial and temporal resolution using the high-speed high-energy X-ray imaging facility at beamline 32-ID-B of the APS. Figure 1 shows an overview of the research setup. It is composed of a vacuum chamber (building environment), an automatic powder spreading system, a laser system, an X-ray source (X-ray outlet), and an X-ray detection/imaging system.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Sailing into uncharted waters: recent advances in the in situ monitoring of catalytic processes in aqueous environments

Catalysis in aqueous environments is attracting enormous interest. Many characterization methods are well established at gas-solid interfaces and a majority of the surface-science approaches were historically limited to model surfaces and vacuum conditions. However, practical scenarios with complex catalyst structures, elevated temperatures and pressures, as well as the presence of two or more condensed phases, can pose significant challenges to these techniques, particularly for catalysts at their dynamic working states. In such contexts, this review highlights the advances over the past five years in the in situ and real-time detection of catalytic processes and related phenomena in aqueous media, ideally under realistic conditions. We underline latest technical innovations, describe novel chemistries that are made accessible by recently developed toolboxes, and discuss future directions of in situ and time-resolved analytical approaches applicable to aqueous phase catalysis.

Heterogeneous catalysis, in situ, time-resolved, s↗

Membrane translocation process revealed by in situ structures of type II secretion system secretins

The GspD secretin is the outer membrane channel of the bacterial type II secretion system (T2SS) which secrets diverse toxins that cause severe diseases such as diarrhea and cholera. GspD needs to translocate from the inner to the outer membrane to exert its function, and this process is an essential step for T2SS to assemble. Here, we investigate two types of secretins discovered so far in Escherichia coli , GspD α , and GspD β . By electron cryotomography subtomogram averaging, we determine in situ structures of key intermediate states of GspD α and GspD β in the translocation process, with resolution ranging from 9 Å to 19 Å. In our results, GspD α and GspD β present entirely different membrane interaction patterns and ways of transitioning the peptidoglycan layer. From this, we hypothesize two distinct models for the membrane translocation of GspD α and GspD β , providing a comprehensive perspective on the inner to outer membrane biogenesis of T2SS secretins.

59 BASIC BIOLOGICAL SCIENCES↗

In-Situ Detection of Process-Induced Porosity During Cure of Out-of-Autoclave Composites

Composite materials offer unique benefits in aerospace applications, including high strength-to-weight ratio, and are becoming increasingly used by industry manufacturers. Current manufacturing and processing methods can lead to defects in the composites, which are identified after fabrication using inspection methods. This study utilized a high-temperature ultrasonic inspection system to detect process-induced porosity in an out-of-autoclave (OOA) composite panel during cure. In order to perform ultrasonic scans in-situ during cure, the system needed to be able to operate at oven temperatures up to 200 °C. There are no commercially available ultrasonic scanning systems that can operate continuously at these temperatures, so an enclosure was fabricated to insulate the ultrasonic system in the curing oven. The enclosure housed a MISTRAS® motorized X-Y raster scanner and contact transducer (Olympus® X2002). The Olympus® X2002 contact transducer is a continuous high-temperature delay line transducer with a center frequency of 2.25 MHz. In order to prevent the inside of the enclosure from reaching high temperatures, a sparge pipe inside the cooling enclosure was connected to a liquid nitrogen (LN2) tank outside of the oven via insulated hoses. The cooling system was automatically controlled by a temperature controller that was programmed to open a solenoid valve along the hose at 31 ℃ and close at 28 ℃ inside the cooling enclosure. When the solenoid valve was open, LN2 would flow from the LN2 tank and vaporize prior to reaching cooling enclosure. A U-shaped sparge pipe had holes drilled along its length to uniformly introduce cold nitrogen gas into the cooling enclosure. This prevented the motors from ever reaching the maximum desired operating temperature of 38 ℃. In the bottom of the enclosure, the tool plate was placed with the composite facing the outside of the enclosure, exposing it to the temperatures of the oven. The tool plate was 63.5 mm thick borosilicate glass, which was chosen for its low ultrasonic attenuation and moderate thermal conductivity. A thin layer of ultrasonic couplant was placed on the tool plate. The transducer sent and received ultrasonic waves through the tool plate into the composite. A MISTRAS® Remote UT System performed all wave generation, analog to digital conversion, and data acquisition and processing. The transducer was connected directly to the Remote UT System via a high-temperature BNC cable (CD International, RG-316). Polyimide insulated copper wire was used to connect the scanner to a 2-axis motor drive, which was connected to the Remote UT System. The motor drive and Remote UT System were located outside the industrial oven. A diagram of the ultrasonic system is shown in Figure 1. Figure 1: Diagram of ultrasonic in-situ defect detection system. In this study, a porosity gradient was introduced into the carbon fiber reinforced polymer (CFRP) composite through a misfit of the part and caul plate. A 24-ply quasi-isotropic ([0/90, ±45]12S) composite panel was laid up using Newport® AS4C-M/NB321 out-of-autoclave (OOA) plain weave (PW) prepreg (42% resin content, 195 g/m2). The first 16 plies were 203 mm × 203 mm. Ply drops were incorporated into the panel by decreasing the length of plies 17-24. The sizes of each ply are included in Table 1. All plies were centered along their length (x-axis) creating a trapezoidal type cross-section. Table 1: Ply sizes Plies Length (mm) Width (mm) 1-16 203 203 17-18 102 203 19-20 85 203 21-22 68 203 23-24 51 203 A 15-5 stainless steel caul plate (Size: 203 × 203 × 1.2 mm) was placed on the laminate. The composite and caul plate were vacuum bagged to the tool plate. Per the product datasheet, Newport 321 can be cured between 121 °C and 149 °C, depending on service temperature, with a hold for 90-120 minutes. Based on prior thermal testing of the cooling enclosure, the desired composite temperature cycle could be attained when the air temperature of the oven was ramped to 160 °C at a rate of 1.7 °C/min with a 3 hour hold. The extended hold was not necessary to cure the composite, but did allow for additional scans at the cure temperature during preliminary testing. The composite panel was under vacuum pressure for the entire cure cycle. Under vacuum, the caul plate deformed causing high and low pressure regions. The low-pressure regions formed high porosity in the composite part. The ultrasonic data collected showed that the inspection system was able to monitor the evolution of porosity within the composite throughout the cure cycle. Fifty scans of a 203 mm × 51 mm (8 in. × 2 in.) area of the composite were completed throughout the cure cycle. The scan speed was set to 43 mm/s in the x-direction and 36 mm/s in the y-direction, with a 1.0 mm/pixel resolution in both directions. Each scan took approximately five minutes to complete. Figure 2 shows C-scan amplitude data (top view) from one scan during the cure cycle. The color map indicates the maximum amplitude (%) measured with a time gate that contains reflections from the back surface (furthest from the transducer in contact with the caul plate) of the composite. Because porosity in the composite increases the ultrasonic attenuation in the composite part, a higher amplitude (red) indicates low porosity and a lower amplitude (blue) indicates high porosity. The regions where the caul plate was applying increased pressure (center and ends of the panel) resulted in reduced porosity, whereas the ply drop regions had reduced pressure and thus had higher porosity. Figure 2: Amplitude C-scan (top view) of OOA composite from one scan during the 160 °C temperature hold. Higher amplitude (red) indicates low porosity. Lower amplitude (blue) indicates high porosity. A B-scan is a two-dimensional image plotting the ultrasonic signals from a single y-position at every x-location of the composite panel. The travel time (μs) of the ultrasonic wave (representing the through-thickness location) is plotted along the y-axis, and the ultrasonic wave signal is represented as a contour map. Based on the B-scan data, the location of the defects with respect to the composite thickness was able to be determined. The ply drop regions had high porosity near the front (tool plate) surface of the composite (Figure 3). Figure 3: B-scan (cross-section view) of OOA composite from one scan during the 160 °C temperature hold. Using the data obtained from amplitude C-scans and B-scans throughout the cure cycle, the high and low porosity regions within the composite laminate were detected and localized with high spatial resolution. This paper will discuss the evolution of porosity content in the OOA composite during cure. OOA tests aided the transition of this system to an autoclave, which is the primary method of curing aerospace-grade thermoset composites.

Tyler B. Hudson↗