Search NASA⌕ Search

SEARCH · Search NASA

Results for “LIFT DISTRIBUTION - WINGS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1943

Jet-boundary corrections for reflection-plane models in rectangular wind tunnel

A detailed method for determining the jet-boundary corrections for reflection-plane models in rectangular wind tunnels is presented. The method includes the determination of the tunnel span local distribution and the derivation of equations for the corrections to the angle of attack, the lift and drag coefficients, and the pitching-, rolling-, yawing-, and hinge-moment coefficients. The principle effects of aerodynamic induction and of the boundary-induced curvature of the streamlines have been considered. An example is included to illustrate the method. Numerical values of the more important corrections for reflection-plane models in 7 by 10-foot closed wind tunnels are presented.

Swanson, Robert S↗
NASA NTRS1959

Charts of the Induced Velocities Near a Lifting Rotor

A compilation of charts of the induced velocities near a lifting rotor is presented. The charts cover uniform as well as various non-uniform distributions of disk loading and should be applicable to many aerodynamic interference problems involving rotors.

Jewel, Joseph W., Jr.↗
NASA NTRS1980

Effect of tip vortex structure on helicopter noise due to blade-vortex interaction

A potential cause of helicopter impulsive noise, commonly called blade slap, is the unsteady lift fluctuation on a rotor blade due to interaction with the vortex trailed from another blade. The relationship between vortex structure and the intensity of the acoustic signal is investigated. Unsteady lift on the blades due to blade-vortex interaction is calculated using linear unsteady aerodynamic theory, and expressions are derived for the directivity, frequency spectrum, and transient signal of the radiated noise. The inviscid rollup model of Betz is used to calculate the velocity profile in the trailing vortex from the spanwise distribution of blade tip loading. A few cases of tip loading are investigated, and numerical results are presented for the unsteady lift and acoustic signal due to blade-vortex interaction. The intensity of the acoustic signal is shown to be quite sensitive to changes in tip vortex structures.

Widnall, S. E.↗
NASA NTRS1976

Shockless airfoils with thicknesses of 20.6 and 20.7 percent chord analytically designed for a Mach number of 0.68 and a lift coefficient of 0.40

A 20.8 percent-thick airfoil shape was designed to have shockless inviscid flow at a Mach number of 0.68 and a lift coefficient of 0.40. In order to determine the actual airfoils which would yield this same shockless flow when viscous effects are included, boundary layer displacement thicknesses were subtracted from the inviscid shape for Reynolds numbers of 100 and 35 million. This process yielded airfoils with thicknesses of 20.7 and 20.6 percent, respectively. Subtraction of boundary layer displacement thicknesses for Reynolds numbers below 35 million yielded nonphysical airfoils, that is airfoils with negative thicknesses near tHe trailing edge. The pitching moment about the quarter-chord point at the design condition was -0.082 for the inviscid shape and, consequently, for both airfoils. Off-design calculations for the two airfoils were made using a computer program which provides for the interaction of the inviscid flow and boundary layer solutions. The pressure distributions of the airfoils were shockless for conditions from the design point to lower Mach numbers and lift coefficients. No boundary layer separation was predicted except in the last 3 percent chord on the upper surface.

Allison, D. O.↗
NASA NTRS1959

Chordwise Pressure Distributions over Several NACA 16-Series Airfoils at Transonic Mach Numbers up to 1.25

A two-dimensional wind-tunnel investigation of the pressure distributions over several NACA 16-series airfoils with thicknesses of 4, 6, 9, and 12 percent of the chord and design lift coefficients of 0, 0.2, 1 and 0.5 has been conducted in the Langley airfoil test apparatus at transonic Mach numbers from 0.7 to 1.25. The tests ranged in Reynolds number from 2.4 x 10 (exp 6) to 2.8 x 10 (exp 6) and in angle of attack from -10 to 12 degrees. Chordwise pressure distributions and schlieren flow photographs are presented without analysis.

Ladson, Charles L.↗
DOE OSTI2022

Film Cooling Performance Prediction for Air and Supercritical CO 2

The current study explores the possibility of cooling the vanes and blades of a direct-fired sCO 2 turbine using film cooling. The operating conditions of a direct-fired sCO 2 cycle and thermophysical properties of the fluid at those conditions can alter the flow field characteristics of the coolant jet and its mixing with the mainstream. Very little information is present in the literature regarding the performance of film cooling geometries employing supercritical CO 2 . The objective of this study is to estimate the resulting film cooling effectiveness while also capturing the effects of the crossflow-to-mainstream velocity ratio on the coolant jet. Herein, a computational fluid dynamic model is used to study the coolant jet exiting a cylindrical hole located on a flat plate, with the coolant fed by an internal channel. Steady-state Reynolds-averaged Navier–Stokes equations were solved along with the (shear-stress transport) SST k–ω model to provide the turbulence closure. The operating conditions for the direct-fired sCO 2 turbine are obtained using an in-house Cooled Turbine Model. Numerical predictions revealed that the crossflow effects and jet lift-off were more pronounced in the case of sCO 2 when compared to air. Spatial distribution of flow field and cooling effectiveness are presented at different operating conditions.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2021

Film Cooling Performance Predictions For Air And Supercritical CO 2

The current study explores the possibility of cooling the vanes and blades of a direct-fired sCO 2 turbine using film cooling geometries. The operating conditions of a direct-fired sCO 2 cycle and thermophysical properties of the fluid at those conditions can alter the flow field characteristics of the coolant jet and its mixing with the mainstream. Very little information is present in the literature regarding the performance of film cooling geometries employing a supercritical fluid. The objective of this study is to estimate the resulting film cooling effectiveness while also capturing the effects of the crossflow-to-mainstream velocity ratio on the coolant jet. A computational fluid dynamic model is used to study the coolant jet exiting a cylindrical hole located on a flat plate, with the coolant fed by an internal channel. Steady-state RANS equations were solved along with the SST kω model to provide the turbulence closure. The operating conditions for the direct-fired sCO 2 turbine are obtained using an in-house Cooled Turbine Model. Numerical predictions revealed that the crossflow effects and jet lift-off were more pronounced in the case of sCO 2 when compared to air. Spatial distribution of flow field and cooling effectiveness will be presented at different operating conditions. Recommendations for future studies will be given wherever applicable.

42 ENGINEERING↗
NASA NTRS1979

High lift selected concepts

The benefits to high lift system maximum life and, alternatively, to high lift system complexity, of applying analytic design and analysis techniques to the design of high lift sections for flight conditions were determined and two high lift sections were designed to flight conditions. The influence of the high lift section on the sizing and economics of a specific energy efficient transport (EET) was clarified using a computerized sizing technique and an existing advanced airplane design data base. The impact of the best design resulting from the design applications studies on EET sizing and economics were evaluated. Flap technology trade studies, climb and descent studies, and augmented stability studies are included along with a description of the baseline high lift system geometry, a calculation of lift and pitching moment when separation is present, and an inverse boundary layer technique for pressure distribution synthesis and optimization.

Henderson, M. L.↗
NASA NTRS1986

Computer simulation of a wind tunnel test section with discrete finite-length wall slots

A computer simulation of a slotted wind tunnel test section which includes a discrete, finite-length wall slot representation with plenum chamber constraints and accounts for the nonlinear effects of the dynamic pressure of the slot outflow jet and of the low energy of slot inflow air was developed. The simulation features were selected to be those appropriate for the intended subsequent use of the simulation in a wall interference assessment procedure using sparsely located wall pressure measurements. It is demonstrated that accounting for slot discreteness is important in interpreting wall pressure measured between slots, and that accounting for nonlinear slot flow effects produces significant changes in tunnel-induced velocity distributions and, in particular, produces a longitudinal component of tunnel-induced velocity due to model lift. A characteristic mode of tunnel flow interaction with constraints imposed by the plenum chamber and diffuser entrance is apparent in simulation results and is derived analytically through a simplified analysis.

Kemp, W. B., Jr.↗
NASA NTRS1986

Structural and aerodynamic loads and performance measurements of an SA349/2 helicopter with an advanced geometry rotor

A flight test program was conducted to obtain data from an upgraded Gazelle helicopter with an advanced geometry, three bladed rotor. Data were acquired on upper and lower surface chordwise blade pressure, blade bending and torsion moments, and fuselage structural loads. Results are presented from 16 individual flight conditions, including level flights ranging from 10 to 77 m/sec at 50 to 3000 m altitude, turning flights up to 2.0 g, and autorotation. Rotor aerodynamic data include information from 51 pressure transducers distributed chordwise at 75, 88, and 97% radial stations. Individual tranducer pressure coefficients and airfoil section lift and pitching moment coefficients are presented, as are steady state flight condition parameters and time dependence rotor loads. All dynamic data are presented as harmonic analysis coefficients.

Heffernan, Ruth M.↗
NASA NTRS1987

A free-wake rotor analysis including ground effect

The objective of this work is to develop a computer program which analytically estimates the wake geometry, vorticity, and velocity distribution over a rotor and in the neighboring airflow for a variety of conditions in and out of ground effect. The resulting wake is used to provide an assessment of the blade loading distribution for various hover and low speed flight conditions. The computer program is based on a lifting line free wake model and provides stable solutions for a variety of steady state conditions, including ground effect and forward flight. The wake program was validated by comparing the computed wake geometry and experimental test data for two different rotors.

Saberi, H. A.↗
NASA NTRS1989

Integration of scramjets with waverider configurations

This paper presents a parametric study of a scramjet propulsion system integrated into a waverider lifting-body configuration. The analysis explores the effect of inlet geometry, internal cross-section-area distribution of the combustor section, the distribution of the heat release of the reacting mixture, the heat transfer, and the friction on the performance of the propulsion system. The Mach number, temperature, and pressure distributions within the scramjet model are studied parametrically, and the effects on the thrust are obtained. The results provide insight on the design concepts and problems that might arise for a given internal-flow configuration.

Rasmussen, M. L.↗
NASA NTRS1944

Analysis of Experimental Investigations of the Planing Process of the Surface of Water

Pressure distribution and spray measurements were carried out on rectangular flat and V-bottom planing surfaces. Lift, resistance, and center of pressure data are analyzed and it is shown how these values may be computed for the pure planing procees of a flat or V-bottom suface of arbitrary beam, load and speed, the method being illustrated with the aid of an example.

Sottorf, W.↗
NASA NTRSDate not supplied

Design of a Propeller with Global Minimum Torque

Academia, industry, and Government are actively working towards a future where dozens of small to large Unmanned Aerial Systems (UAS) are present within urban environments. In this environment, high noise pollution and inefficiencies have the potential to render these new technologies impractical due to public annoyance and nonacceptance. This study aims to design and analyze a novel propeller design for minimum global torque using an optimization algorithm to find the full three dimensional solution of maximum efficiency. This resulted in a 𝐶 𝑙 distribution defining the global minimum torque solution for propeller design which corresponded with moving as much lift inboard as possible and reducing lift rapidly at the blade tip. The novel propeller (dubbed "Prandtl" propeller) was then compared with the current gold standard in propeller design, a minimum induced loss (MIL) propeller, which had all the same geometric properties except for blade twist and produced the same amount of thrust at the same advance ratio. The results of multiple iterations of Prandtl propellers showed an increase in efficiency of 2.0-3.3% for the Prandtl blade when compared to the equivalent MIL blade. A potential added benefit of this blade design is lower noise generation due to the lower lift loading at the tip reducing the large shear layer intensity which is the point source of noise in propellers. Two major breakthroughs for enabling widespread use of UAS in urban environments are noise reduction and vehicle efficiency, and this new propeller design has the potential to provide both.

Propeller↗
NASA NTRSDate not supplied

Design of a Propeller with Global Minimum Torque

Academia, industry, and Government are actively working towards a future where dozens of small to large Unmanned Aerial Systems (UAS) are present within urban environments. In this environment, high noise pollution and inefficiencies have the potential to render these new technologies impractical due to public annoyance and nonacceptance. This study aims to design and analyze a novel propeller design for minimum global torque using an optimization algorithm to find the full three dimensional solution of maximum efficiency. This resulted in a 𝐶 𝑙 distribution defining the global minimum torque solution for propeller design which corresponded with moving as much lift inboard as possible and reducing lift rapidly at the blade tip. The novel propeller (dubbed "Prandtl" propeller) was then compared with the current gold standard in propeller design, a minimum induced loss (MIL) propeller, which had all the same geometric properties except for blade twist and produced the same amount of thrust at the same advance ratio. The results of multiple iterations of Prandtl propellers showed an increase in efficiency of 2.0-3.3% for the Prandtl blade when compared to the equivalent MIL blade. A potential added benefit of this blade design is lower noise generation due to the lower lift loading at the tip reducing the large shear layer intensity which is the point source of noise in propellers. Two major breakthroughs for enabling widespread use of UAS in urban environments are noise reduction and vehicle efficiency, and this new propeller design has the potential to provide both.

Propeller↗
NASA NTRS1993

Measurements in 80- by 120-foot wind tunnel of hazard posed by lift-generated wakes

The large, low speed wind tunnel at NASA-Ames has been used to study the characteristics of lift-generated vortices involved in the definition of aircraft-separation criteria, in order to enhance airport capacity without compromising safety. Attention is given to the potential hazard caused by the vortex wake of several configurations of a subsonic transport. Measured downwash distributions in the wake of three different wake-generator configurations are obtained by means of a vortex-lattice method, in order to predict the lift and rolling moment on several models of wake-following aircraft.

Rossow, V. J.↗
NASA NTRSDate not supplied

Exploring the Climatic Impact of Bi-Modal Dust Particle Size Distributions During the MY34/2018 Global Dust Storm with the NASA Ames Mars Global Climate Model.

We have implemented a bi-modal dust lifting scheme in the NASA Ames Mars Global Climate Model (GCM) and investigated the climatic impact on the MY34/2018 Global Dust Storm (GDS). We found that the climate is measurably responsive to the inclusion of a second, smaller dust mode. Dust tends to be lifted through a deeper column in the atmosphere, which is reflected in the climate as changes to atmospheric temperature, tide amplitudes, and surface temperatures. Adding a modest fraction of a smaller dust mode improves simulations during the GDS compared to Curiosity semi-diurnal tide observations as well as Mars Climate Sounder (MCS) T15 brightness temperatures

R A Urata↗
NASA NTRS2000

Parallel performance investigations of an unstructured mesh Navier-Stokes solver

A Reynolds-averaged Navier-Stokes solver based on unstructured mesh techniques for analysis of high-lift configurations is described. The method makes use of an agglomeration multigrid solver for convergence acceleration. Implicit line-smoothing is employed to relieve the stiffness associated with highly stretched meshes. A GMRES technique is also implemented to speed convergence at the expense of additional memory usage. The solver is cache efficient and fully vectorizable, and is parallelized using a two-level hybrid MPI-OpenMP implementation suitable for shared and/or distributed memory architectures, as well as clusters of shared memory machines. Convergence and scalability results are illustrated for various high-lift cases.

Mavriplis, Dimitri J.↗