Search NASA⌕ Search

SEARCH · Search NASA

Results for “Lift coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1940

Investigation of the Characteristics of a High-Aspect-Ratio Wing in the Langley 8-Foot High-Speed Tunnel

An investigation of the characteristics of a wing with an aspect ratio of 9.0 and an NACA 65-210 airfoil section has been made at Mach number up to 0.925. The wing tested has a taper ratio of 2.5:1.0, no twist, dihedral, or sweepback, and 20-percent - chord 37.5-percent-semispan plain ailerons. The results showed that serious changes in the normal-force characteristics occurred when the Mach number was increased above 0.74 at angles of attack between 4 deg. and 10 deg. and above 0.80 at 0 deg. angle of attack.Because of small outboard shifts in the lateral center of load, the bending moment at the root for conditions corresponding to a 3g pull-out at an altitude of 35,000 feet increased by approximately 5% when the Much number was increased beyond 0.83 the negative pitching moments for the high angles of attack increased, whereas those for the low angles of attack decreased with a resulting large increase in the negative slope of the pitching-moment curves. A large increase occurred in the values of the drag coefficients for the range of lift coefficients needed for level flight at an altitude of 35,000 feet when the Mach number was increased beyond a value of 0.80. The wakes at a station 2.82 root chords behind the wing quarter-chord line extended approximately a chord above the wing chord line for the angles of attack required to recover from high-speed dives at high Mach numbers.

Whitcomb, Richard T.↗
NASA NTRSDate not supplied

Aerodynamic Design Optimization for Natural Laminar Flow Airfoils

Natural laminar flow technology is a passive laminar flow control (LFC) strategy that seeks to delay the onset of boundary-layer transition (BLT) through shape optimization to reduce the drag of the aerodynamic vehicle. Adjoint-based design optimization for LFC is proposed in an integrated multidisciplinary framework, which includes the computational fluid dynamics (CFD), geometry and grid deformation, and linear stability analysis (LSA) for transition prediction. In particular, the BLT location is predicted using the dual N-factor method that is based on a linear stability theory (LST) eigenvalue problem. The dual N-factor criterion accounts for the amplification of planar Tollmien-Schlichting (TS) and stationary crossflow (CF) boundary-layer instabilities to predict the transition location in three-dimensional boundary-layer flows. The adjoint-based shape optimization procedure is based on an iteratively coupled CFD and LSA methodology to converge the transition location and flow solutions, as well as to calculate the sensitivities of the aerodynamic metrics of interest with respect to the flow and shape design parameters. The RAE 2822 airfoil at 0 and 30 degrees yaw angles, an angle of attack of 0.72 degrees, and subsonic conditions (M∞ = 0.19, Rec = 5.6 × 106 ) are used as baseline configurations for design optimization. The angle of attack and the vertical displacement of free-form-deformation control points are used as design variables to reduce the drag coefficient while reaching a specified lift coefficient. The optimized unswept airfoil designs achieve a 30% drag reduction accompanied by a downstream shift of the transition locations over both suction and pressure sides of the airfoil. The initial design iterations for the swept case also show a favorable trend in the drag reduction with transition delay over both sides.

Transition↗
NASA NTRS1957

Wind-tunnel Investigation of External-flow Jet-augmented Double Slotted Flaps on a Rectangular Wing at an Angle of Attack of 0 Degree to High Momentum Coefficients

A wind-tunnel investigation has been made to determine the characteristics of external-flow jet-augmented double slotted flaps which appear suitable for application to airplanes with pod-mounted engines. The investigation included tests of the rectangular wing with an aspect ratio of 6 over a momentum-coefficient range from 0 to 28. Lift coefficients larger than the jet reaction in the lift direction were obtained with the external-flow jet-augmented double slotted flaps.

HIGH-LIFT DEVICES - COMPLETE WINGS↗
NASA NTRS1981

An investigation of the use of a propulsive wing/canard concept for improved maneuvering

The propulsive wing concept is an extension of the flap boundary layer control utilized on several aircraft configurations. Several studies have been made regarding the benefits of the propulsive wing in STOL operation. However, the propulsive wing/canard provides performance benefits also in areas other than STOL. It is expected to improve the maneuvering capability by providing reduced drag at high lift coefficients without appreciably affecting the low lift drag. An increase in the buffet free load factor can also be expected with the blown wing and canard. Attention is given to a program to investigate the wing/canard at maneuvering conditions, and tests at ranges of blowing coefficients equivalent to STOL operation.

Stewart, V. R.↗
NASA NTRS1987

Winglets on low aspect ratio wings

The drag reduction potentially available from the use of winglets at the tips of low aspect ratio (1.75-2.67) wings with pronounced (45-60 deg) leading edge sweep is assessed numerically for the case of a cruise design point at Mach of 0.8 and a lift coefficient of 0.3. Both wing-winglet and wing-alone design geometries are derived from a linear-theory, minimum induced drag design methodology. Relative performance is evaluated with a nonlinear extended small disturbance potential flow analysis code. Predicted lift coefficient/pressure drag coefficient increases at equal lift for the wing-winglet configurations over the wing-alone planform are of the order of 14.6-15.8, when boundary layer interaction is included.

Kuhlman, John M.↗
NASA NTRS1996

Prediction of Airfoil Characteristics With Higher Order Turbulence Models

This study focuses on the prediction of airfoil characteristics, including lift and drag over a range of Reynolds numbers. Two different turbulence models, which represent two different types of models, are tested. The first is a standard isotropic eddy-viscosity two-equation model, and the second is an explicit algebraic stress model (EASM). The turbulent flow field over a general-aviation airfoil (GA(W)-2) at three Reynolds numbers is studied. At each Reynolds number, predicted lift and drag values at different angles of attack are compared with experimental results, and predicted variations of stall locations with Reynolds number are compared with experimental data. Finally, the size of the separation zone predicted by each model is analyzed, and correlated with the behavior of the lift coefficient near stall. In summary, the EASM model is able to predict the lift and drag coefficients over a wider range of angles of attack than the two-equation model for the three Reynolds numbers studied. However, both models are unable to predict the correct lift and drag behavior near the stall angle, and for the lowest Reynolds number case, the two-equation model did not predict separation on the airfoil near stall.

Gatski, Thomas B.↗
NASA NTRS1983

Family of airfoil shapes for rotating blades

An airfoil which has particular application to the blade or blades of rotor aircraft such as helicopters and aircraft propellers is described. The airfoil thickness distribution and camber are shaped to maintain a near zero pitching moment coefficient over a wide range of lift coefficients and provide a zero pitching moment coefficient at section Mach numbers near 0.80 and to increase the drag divergence Mach number resulting in superior aircraft performance.

Noonan, K. W.↗
NASA NTRS1983

Wing contamination - Threat to safe flight

Attention is given to the initial results of systematic investigations of the potentially hazardous effect of heavy rain, ice, and frost accretion on aircraft wings. In the laminar region of an airfoil, roughness interferes with smooth flow and tends to encourage transition from laminar to turbulent flow upstream of its normal point of occurrence. In the airfoil's turbulent region, roughness considerably worsens the turbulent friction coefficient, thereby increasing the drag coefficient. Consequent dramatic decreases of maximum lift coefficient at high angles of attack lead to premature stall. Such decreases in stall angle destroy the safety margin of an aircraft approaching stall. An assessment is given to the state of knowledge in this field of research.

Luers, J. K.↗
NASA NTRS1959

Hydrodynamic Characteristics of Two Low-Drag Supercavitating Hydrofoils

An experimental investigation has been conducted in Langley tank no. 2 to determine the hydrodynamic characteristics of two low-drag supercavitating hydrofoils operating in a range of cavitation numbers from 0 to approximately 6. The hydrofoils had aspect ratios of 1 and 3, and the sections were derived by assuming five terms in the vorticity-distribution expansion of the equivalent airfoil. The aspect-ratio-1 hydrofoil was also tested at zero cavitation number with two sets of end plates having depths of 3/8 and 1/4 chords. Zero cavitation number was established by operating the hydrofoils near the water surface so that complete ventilation of the upper surfaces could be obtained. For those depths of submersion where complete ventilation was not obtained through vortex ventilation, two probes were used to introduce air to the upper surfaces of the hydrofoils and to induce complete ventilation. Data were obtained for a range of speeds from 20 to 80 fps, angles of attack from 2 to 20 deg, and ratios of depth of submersion to chord from 0 to 0.85. The experimental results obtained from the aspect-ratio-1 and aspect-ratio-3, five-term hydrofoils were compared with a three-dimensional zero-cavitation-number theory. The theoretical and experimental values of lift and center of pressure for the aspect-ratio-1 hydrofoil were in agreement, within engineering accuracy, for the range of lift coefficients investigated. The theoretical drag coefficients were lower, by a constant amount, than the experimental drag coefficients. The theoretical expressions derived for the lift, drag, and center of pressure of the aspect-ratio-3 hydrofoil were in agreement, within engineering accuracy, with the experimental values. The theoretical and experimental drag coefficients of the aspect-ratio-3 five-term hydrofoil were lower than the theoretical drag coefficients computed for a comparable Tulin-Burkart hydrofoil.

McGehee, John R.↗
NASA NTRS1975

Pressure distributions on a cambered wing body configuration at subsonic Mach numbers

An investigation was conducted in the Langley high-speed 7- by 10-foot tunnel at Mach numbers of 0.20 and 0.40 and angles of attack up to about 22 deg to measure the pressure distributions on two cambered-wing configurations. The wings had the same planform (aspect ratio of 2.5 and a leading-edge-sweep angle of 44 deg) but differed in amounts of camber and twist (wing design lift coefficient of 0.35 and 0.70). The effects of wing strake on the wing pressure distributions were also studied. The results indicate that the experimental chordwise pressure distribution agrees reasonably well with the design distribution over the forward 60 percent of nearly all the airfoil sections for the lower cambered wing. The measured lifting pressures are slightly less than the design pressures over the aft part of the airfoil. For the highly cambered wing, there is a significant difference between the experimental and the design pressure level. The experimental distribution, however, is still very similar to the prescribed distribution. At angles of attack above 12 deg, the addition of a wing-fuselage strake results in a significant increase in lifting pressure coefficient at all wing stations outboard of the strake-wing intersection.

Henderson, W. P.↗
NASA NTRS1975

An analytical evaluation of airfoil sections for helicopter rotor applications

An analytical technique was used to evaluate airfoils for helicopter rotor application. This technique permits assessment of the influences of airfoil geometric variations on drag divergence Mach number at lift coefficients from near zero to near maximum lift. Analytical results presented in this paper indicate the compromises in drag divergence Mach number which result from changes in (1) thickness ratio, (2) location of maximum thickness, (3) leading-edge radius, (4) camber addition, and (5) location of maximum camber of NACA four- and five-digit-series airfoils and some 6-series airfoils of potential interest for helicopters. Examples of airfoil sections which combine several of the geometric changes favorable to both advancing and retreating section performance have been presented.

Bingham, G. J.↗
NASA NTRS1979

Sensitivity study for a remotely piloted microwave-powered sailplane used as a high-altitude observation

The sensitivity of several performance characteristics of a proposed design for a microwave-powered, remotely piloted, high-altitude sailplane to changes in independently varied design parameters was investigated. Results were expressed as variations from baseline values of range, final climb altitude and onboard storage of radiated energy. Calculated range decreased with increases in either gross weight or parasite drag coefficient; it also decreased with decreases in lift coefficient, propeller efficiency, or microwave beam density. The sensitivity trends for range and final climb altitude were very similar. The sensitivity trends for stored energy were reversed from those for range, except for decreasing microwave beam density. Some study results for single parameter variations were combined to estimate the effect of the simultaneous variation of several parameters: for two parameters, this appeared to give reasonably accurate results.

Turriziani, R. V.↗
NASA NTRS1982

A technique for determining powered-lift STOL aircraft performance at sea level from flight data taken at altitude

State-of-the-technology powered-lift STOL aircraft can develop very high lift coefficients. The determination of how this high lift capability can be utilized for landing approaches is accomplished by evaluating aircraft velocity versus flightpath performance. This paper briefly discusses upper-surface-blowing power-lift technology and some of the significant features of the velocity versus flightpath plot that are used in evaluating the performance of powered-lift aircraft. A procedure for deriving the velocity versus flightpath plot for a powered-lift aircraft at any specified weight at sea level, based on flight-test data obtained at various weights and altitudes, is discussed in detail. Actual flight-test data obtained with NASA's Quiet Short-Haul Research Aircraft (QSRA) are used to illustrate this procedure and to evaluate the results.

Stevens, V. C.↗
NASA NTRS1944

Profile-Drag Coefficients of Conventional and Low-Drag Airfoils as Obtained in Flight

Results of flight tests indicate that profile-drag coefficients which were obtained with the low-drag airfoils were lower than with the conventional types over the range of light coefficients tested. For comparable conditions of the lift coefficient and Reynolds Number, the low-drag airfoils have profile-drag coefficients which may be 27 percent lower than the profile drag of the conventional airfoils tested. Detailed results are presented graphically.

AIRFOILS - NAVY N-22 - CHARACTERISTICS↗
NASA NTRS1958

Aerodynamic Characteristics in Sideslip of a Large-Scale 49 deg Sweptback Wing-Body-Tail Configuration with Blowing Applied Over the Flaps and Wing Leading Edge

An investigation has been conducted in the Langley full-scale tunnel to determine the aerodynamic characteristics in sideslip of a large-scale 490 sweptback wing-body-tail configuration having wing leading- edge and flap-blowing boundary-layer control. The wing and tails had an aspect ratio of 3.5, a taper ratio of 0.3, and NACA 65AO06 airfoil sections parallel to the plane of symmetry. The tests were conducted over a range of angles of attack of about -5 deg to 28 deg for sideslip angles of 0 deg, -5.06 deg, -10.15 deg, and -15.18 deg. Lateral and longitudinal stability and control characteristics were obtained for6a minimized blowing rate. The Reynolds number of the tests was 5.2 x 10(exp 6), corresponding to a Mach number of 0.08. The results of the investigation showed that sideslip to angles of about -15 deg did not require, from a consideration of the longitudinal characteristics, blowing rates over the wing leading edge or flap greater than that established as minimum at zero sideslip. The optimum configuration was laterally and directionally stable through the complete lift-coefficient range including the stall; however, maximum lift for sideslip angles greater than about 50 was seriously limited by a deficiency of lateral control. Blowing over the leading edge of the retreating wing in sideslip at a rate greater than that established as minimum at zero sideslip was ineffective in improving the lateral control characteristics. The optimum configuration at zero sideslip had no hysteresis of the aerodynamic parameters upon recovery from stall.

McLemore, H. Clyde↗
NASA NTRS2003

Numerical Simulations of the Steady and Unsteady Aerodynamic Characteristics of a Circulation Control Wing Airfoil

The aerodynamic characteristics of a Circulation Control Wing (CCW) airfoil have been numerically investigated, and comparisons with experimental data have been made. The configuration chosen was a supercritical airfoil with a 30 degree dual-radius CCW flap. Steady and pulsed jet calculations were performed. It was found that the use of steady jets, even at very small mass flow rates, yielded a lift coefficient that is comparable or superior to conventional high-lift systems. The attached flow over the flap also gave rise to lower drag coefficients, and high L/D ratios. Pulsed jets with a 50% duty cycle were also studied. It was found that they were effective in generating lift at lower reduced mass flow rates compared to a steady jet, provided the pulse frequency was sufficiently high. This benefit was attributable to the fact that the momentum coefficient of the pulsed jet, during the portions of the cycle when the jet was on, was typically twice as much as that of a steady jet.

Liu, Yi↗
NASA NTRS1975

Upwash angles near engine inlets of an externally blown flap STOL transport

An investigation was conducted in the Langley V/STOL tunnel to determine the upwash flow angles in the region of the nacelle inlets of a representative powered-lift transport configuration operating at high lift coefficients. The upwash angles were indicated by tufts and measured from photographs. A potential-flow program was used to estimate these flow angles. Large upflow angles exist near the inlets of the nacelles; the highest value (67.3 deg) occurred with flaps at 15, 35, 55 deg, an angle of attack of 25.7 deg, and a thrust coefficient of 4. The upflow angle was found to be strongly dependent on the circulation lift, regardless of the flap deflection, angle of attack, or thrust coefficient used to generate this circulation lift. The potential-flow calculations away from the nacelle inlets agreed fairly well with the experimental data.

Naeseth, R. L.↗