Search NASA⌕ Search

SEARCH · Search NASA

Results for “Lift to Drag Ratio”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

Computations of Viking Lander Capsule Hypersonic Aerodynamics with Comparisons to Ground and Flight Data

Comparisons are made between the LAURA Navier-Stokes code and Viking Lander Capsule hypersonic aerodynamics data from ground and flight measurements. Wind tunnel data are available for a 3.48 percent scale model at Mach 6 and a 2.75 percent scale model at Mach 10.35, both under perfect gas air conditions. Viking Lander 1 aerodynamics flight data also exist from on-board instrumentation for velocities between 2900 and 4400 m/sec (Mach 14 to 23.3). LAURA flowfield solutions are obtained for the geometry as tested or flown, including sting effects at tunnel conditions and finite-rate chemistry effects in flight. Using the flight vehicle center-of-gravity location (trim angle approx. equals -11.1 deg), the computed trim angle at tunnel conditions is within 0.31 degrees of the angle derived from Mach 6 data and 0.13 degrees from the Mach 10.35 trim angle. LAURA Mach 6 trim lift and drag force coefficients are within 2 percent of measured data, and computed trim lift-to-drag ratio is within 4 percent of the data. Computed trim lift and drag force coefficients at Mach 10.35 are within 5 percent and 3 percent, respectively, of wind tunnel data. Computed trim lift-to-drag ratio is within 2 percent of the Mach 10.35 data. Using the nominal density profile and center-of-gravity location, LAURA trim angle at flight conditions is within 0.5 degrees of the total angle measured from on-board instrumentation. LAURA trim lift and drag force coefficients at flight conditions are within 7 and 5 percent, respectively, of the flight data. Computed trim lift-to-drag ratio is within 4 percent of the data. Computed aerodynamics sensitivities to center-of-gravity location, atmospheric density, and grid refinement are generally small. The results will enable a better estimate of aerodynamics uncertainties for future Mars entry vehicles where non-zero angle-of-attack is required.

Edquist, Karl T.↗
NASA NTRS2019

Performance Optimization of Plate Airfoils for Martian Rotor Applications Using a Genetic Algorithm

The Mars Helicopter Technology Demonstrator will be flying on the NASA Mars 2020 rover mission scheduled to launch in July of 2020. The goal is to demonstrate the viability and potential of heavier-than-air vehicles in the Martian atmosphere. Research is performed at the Jet Propulsion Laboratory and NASA Ames Research Center to extend these capabilities and develop the Mars Science Helicopter as the next possible step for Martian rotorcraft. The Mars Science Helicopter mass is scaled up to the 5 to 20 kg range, allowing a greater payload (approximately 0.5 to 2.0 kg), and greater range (approximately 3 km). Key to achieving these targets is careful aerodynamic rotor design. The Martian atmosphere’s low density and the small helicopter rotors result in very low chord-based Reynolds number flows, which reduces rotor performance. A continuous genetic algorithm is developed to optimize airfoil shapes at representative conditions for the Martian atmosphere. Previous research indicates that sharp leading edges and plate-like airfoils can out-perform conventional airfoil shapes. The present optimization allows for camber and thickness variation of curved and polygonal thin airfoils with sharp leading edges. The airfoil performance is evaluated at the highest attainable liftto- drag ratio near a moderate lift coefficient at compressible Mach numbers, as expected for Martian rotor application. Increases between 16% and 29% in airfoil lift-to-drag ratio at fixed lift coefficients are observed when compared with the Mars Helicopter Technology Demonstrator airfoils. Improvements in hover figure of merit are estimated to be between 4% and 10%, when applied to the Mars Helicopter Technology Demonstrator.

Koning, Witold J. F.↗
NASA NTRS2010

Orion Entry Performance-Based Center-of-Gravity Box

The Orion capsule is designed both for Low Earth Orbit missions to the ISS and for missions to the moon. For ISS class missions, the capsule will use an Apollo-style direct entry. For lunar return missions, depending on the timing of the mission, the capsule could perform a direct entry or a skip entry of up to 4800 n.mi. in order to land in the coastal waters of California. The physics of atmospheric re-entry determine the capability of the Orion vehicle. For a given vehicle mass and shape, physics tells us that the driving parameters for an entry vehicle are the hypersonic lift-to-drag ratio (L/D) and the flight path angle at entry interface (gamma(sub EI)). The design of the Orion atmospheric re-entry must meet constraints during both nominal and dispersed flight conditions on landing accuracy, heating rate, total heat load, sensed acceleration, and proper disposal of the Service Module. These constraints define an entry corridor in the space of L/D-gamma(sub EI); if the vehicle falls within this corridor, then all constraints are met. The gamma(sub EI) dimension of the corridor can be further constrained by the gloads experienced during emergency entries. Thus, the entry performance for the Orion vehicle can be described completely by the L/D. Bounds on the hypersonic L/D necessary to achieve all the mission requirements can be defined for the given entry corridor. Landing accuracy performance drives the lower limit on L/D. In order to achieve the desired landing accuracy, a minimum L/D must be ensured. The design of the Thermal Protection System (TPS) drives the upper limit on L/D. A higher L/D can drive mass into the design of the TPS. Conversely, once the TPS is designed, the L/D must be ensured to stay below a certain limit in order for the TPS to stay within its design envelop. The L/D must stay within its upper and lower bounds during dispersed flight conditions. L/D is a function of both the aerodynamics and the center-of-gravity (CG) of the vehicle. The aerodynamics of the vehicle are determined by Computational Fluid Mechanics (CFD) and wind tunnel tests. However, the aerodynamics are not known precisely. Instead, an aerodynamic database has been developed where the aerodynamic coefficients are known to fall within a probabilistic band defined by upper and lower bounds. It is expected that the probabilistic band will shrink after the first missions are flown and real-world data is collected. Until that time, the Orion must be designed to the current aerodynamic database. Thus, for a given aerodynamic database with given uncertainties, the allowable range in L/D can be mapped to an allowable box for the CG location. The CG box is used to set requirements on the dispersions allowed for vehicle packaging and cargo storage. As the aerodynamic uncertainties decrease, the size of the CG box can increase. This paper discusses the technique used to map the minimum and maximum L/D bounds set by the entry performance requirements to the allowable dispersions in CG while accounting for aerodynamic uncertainties. The L/D is defined as the ratio of the lift force to the drag force. It is equivalent to the ratio of lift coefficient (C(sub L)) over drag coefficient (C(sub D)). C(sub L) and C(sub D) are functions of Mach number (M) and angle of attack (alpha). A Mach number of 25 is used as a measuring point of the hypersonic L/D. Variations in C(sub L), C(sub D) and alpha cause variations in L/D. Equation (1) shows the three contributions to the variation in L/D.

Rea, Jeremy R.↗
NASA NTRS1980

Results of a low-speed wind tunnel test of the MDC 2.2M supersonic cruise aircraft configuration

Results of a low speed test conducted in the Full Scale Tunnel at NASA Langley using an advanced supersonic cruise vehicle configuration are presented. These tests used a 10 percent scale model of a configuration that had demonstrated high aerodynamic performance at Mach 2.2 during a previous test program. The low speed model has leading and trailing edge flaps designed to improve low speed lift to drag ratios at high lift and includes devices for longitudinal and lateral/directional control. The results obtained during the low speed test program have shown that full span leading edge flaps are required for maximum performance. The amount of deflection of the leading edge flap must increase with C sub L to obtain the maximum benefit. Over 80 percent of full leading edge suction was obtained up to lift off C sub L's of 0.65. A mild pitch up occurred at about 6 deg angle of attack with and without the leading edge flap deflected. The pitch up is controllable with the horizontal tail. Spoilers were found to be preferable to spoiler/deflectors at low speeds. The vertical tail maintained effectiveness up to the highest angle of attack tested but the tail on directional stability deteriorated at high angles of attack. Lateral control was adequate for landing at 72 m/sec in a 15.4 m/sec crosswind.

Yip, L. P.↗
NASA NTRS1999

Experimental Investigation of a Point Design Optimized Arrow Wing HSCT Configuration

The M2.4-7A Arrow Wing HSCT configuration was optimized for straight and level cruise at a Mach number of 2.4 and a lift coefficient of 0.10. A quasi-Newton optimization scheme maximized the lift-to-drag ratio (by minimizing drag-to-lift) using Euler solutions from FL067 to estimate the lift and drag forces. A 1.675% wind-tunnel model of the Opt5 HSCT configuration was built to validate the design methodology. Experimental data gathered at the NASA Langley Unitary Plan Wind Tunnel (UPWT) section #2 facility verified CFL3D Euler and Navier-Stokes predictions of the Opt5 performance at the design point. In turn, CFL3D confirmed the improvement in the lift-to-drag ratio obtained during the optimization, thus validating the design procedure. A data base at off-design conditions was obtained during three wind-tunnel tests. The entry into NASA Langley UPWT section #2 obtained data at a free stream Mach number, M(sub infinity), of 2.55 as well as the design Mach number, M(sub infinity)=2.4. Data from a Mach number range of 1.8 to 2.4 was taken at UPWT section #1. Transonic and low supersonic Mach numbers, M(sub infinity)=0.6 to 1.2, was gathered at the NASA Langley 16 ft. Transonic Wind Tunnel (TWT). In addition to good agreement between CFD and experimental data, highlights from the wind-tunnel tests include a trip dot study suggesting a linear relationship between trip dot drag and Mach number, an aeroelastic study that measured the outboard wing deflection and twist, and a flap scheduling study that identifies the possibility of only one leading-edge and trailing-edge flap setting for transonic cruise and another for low supersonic acceleration.

Narducci, Robert P.↗
NASA NTRS2006

Optimum Design of a Compound Helicopter

A design and aeromechanics investigation was conducted for a 100,000-lb compound helicopter with a single main rotor, which is to cruise at 250 knots at 4000 ft/95 deg F condition. Performance, stability, and control analyses were conducted with the comprehensive rotorcraft analysis CAMRAD II. Wind tunnel test measurements of the performance of the H-34 and UH-1D rotors at high advance ratio were compared with calculations to assess the accuracy of the analysis for the design of a high speed helicopter. In general, good correlation was obtained when an increase of drag coefficients in the reverse flow region was implemented. An assessment of various design parameters (disk loading, blade loading, wing loading) on the performance of the compound helicopter was conducted. Lower wing loading (larger wing area) and higher blade loading (smaller blade chord) increased aircraft lift-to-drag ratio. However, disk loading has a small influence on aircraft lift-to-drag ratio. A rotor parametric study showed that most of the benefit of slowing the rotor occurred at the initial 20 to 30% reduction of the advancing blade tip Mach number. No stability issues were observed with the current design. Control derivatives did not change significantly with speed, but the did exhibit significant coupling.

Yeo, Hyeonsoo↗
NASA NTRS1991

Application of waverider-based configurations to hypersonic vehicle design

The hypersonic waverider concept is explored in the context of aircraft design and optimization. Waveriders are vehicles which provide the highest known values of lift-to-drag ratio, suggesting that they are ideal for hypersonic cruise applications. However, these high lift-to-drag ratios are not retained with engine integration. It is shown that waveriders may have applications to the design of accelerating vehicles, even though high L/D is no longer a priority, because they exhibit relatively low drag, and have highly desirable properties for engine/airframe integration. Along these lines, waveriders provide highly uniform flowfields, making them ideal for forebodies on engine-airframe integrated configurations. The inverse design methodology of a waverider lends itself readily to the vehicle design process. Characteristics which govern the performance of a hypersonic vehicle for cruise and accelerating flight are examined, and applied to waverider vehicle design. Finally, it is shown that waveriders, though configured for the specific shock flowfield of a single design point, have acceptable off-design performance characteristics.

Lewis, Mark J.↗
NASA NTRS1958

Lift, Drag, and Pitching Moment of an Aspect-Ratio-2 Triangular Wing with Leading-Edge Flaps Designed to Simulate Conical Camber

An investigation was conducted to determine the effectiveness of leading-edge flaps in reducing the drag at lifting conditions of a triangular wing of aspect ratio 2.0. The flaps, deflected to simulate conically cambered wings having a wide range of design lift coefficients, were tested over a Mach number range of 0.70 to 2.22 through an angle-of-attack variation from -6 deg to +18 deg at a constant Reynolds number of 3.68 million based on the wing mean aerodynamic chord. A symmetrical wing of the same plan form and aspect ratio was also tested to provide a basis for comparison. The experimental results showed that with the flaps in the undeflected position, a small amount of fixed leading-edge droop incorporated over the outboard 5 percent of the wing semispan was as effective at high subsonic speeds as conical camber in improving the maximum lift-drag ratio above that of the symmetrical wing. At supersonic speeds, the penalty in minimum drag above that of the symmetrical wing was less than that incurred by conical camber. Deflecting the leading-edge flaps about the hinge line through 80 percent of the wing semispan resulted in further improvements of the drag characteristics at lift coefficients above 0.20 throughout the Mach number range investigated. The lift and pitching-moment characteristics were not significantly affected by the leading-edge flaps.

Menees, Gene P.↗
NASA NTRS1992

Advanced takeoff procedures for high-speed civil transport community noise reduction

Advanced takeoff procedures were developed for a Mach 2.62 high-speed civil transport configuration (HSCT) equipped with turbine bypass engines, with the goal of reducing the takeoff noise levels for certification to FAR 36, Stage 3 noise levels. The detailed takeoff and landing module for the Flight Optimizations System (FLOPS) computer program was used to generate takeoff profiles. All takeoff procedures were constrained to meet a FAR takeoff field length of 11,000 feet, as well as the minimum required engine-out climb gradients for each airbome segment. Aircraft noise levels at the FAR 36 certification points were calculated using the Aircraft Noise Prediction Program (ANOPP). The study showed that using advanced takeoff procedures in noise certification could result in a 2.25 dB reduction in the amount of noise suppression required to certify this configuration for Stage 3 noise limits. Advanced procedures also resulted in an 8 percent reduction in the 100 EPNdB noise footprint area compared to basic FAR 36 takeoff procedures. In addition, improvements in the lift-to-drag ratio using high-lift devices were shown to produce 1.81 dB more noise reduction when used in combination with advanced takeoff procedures.

Olson, E. D.↗
NASA NTRS1992

Optimal control of lift/drag ratios on a rotating cylinder

We present the numerical solution to a problem of maximizing the lift to drag ratio by rotating a circular cylinder in a two-dimensional viscous incompressible flow. This problem is viewed as a test case for the newly developing theoretical and computational methods for control of fluid dynamic systems. We show that the time averaged lift to drag ratio for a fixed finite-time interval achieves its maximum value at an optimal rotation rate that depends on the time interval.

Ou, Yuh-Roung↗
DOE OSTI2025

Design of a Preliminary Family of Airfoils for High Reynolds Number Wind Turbine Applications

For the past 30 years, offshore wind turbines exhibited a continual pattern of growth that is expected to continue as the industry pushes for higher efficiency. Current designs for the next generation of wind turbines are so large that the chordwise Reynolds number of the blades is well beyond the design range of existing open-source airfoil families. This paper presents a preliminary family of new airfoils designed specifically for the needs of these next-generation offshore turbines, ranging from 21% thick to 30% thick with operating Reynolds numbers between 12 million and 18 million. These airfoils are intended to be alternative to the FFA airfoils that are commonly used on reference turbines such as the IEA 15MW and 22MW designs. In this work, airfoil performance metrics and design targets are developed, the design process is outlined, an optimization scheme is presented, and finally the airfoils and their simulated performance are compared to existing baselines. Lift to drag ratios in a clean condition were improved by up to 49.3% from the baseline FFA airfoil, and rough condition lift to drag ratio was improved by up to 9.3%. It is estimated that the cumulative improvements provided by this airfoil family would result in an approximately 1% increase of Annual Expected Power (AEP) for the 22 MW turbine compared to the current baseline.

airfoils↗
NASA NTRSDate not supplied

Flight Performance Estimates for the NASA X-57 Distributed Electric Propulsion Flight Demonstrator

The X-57 flight demonstrator concept featured four configurations starting with a conventional combustion-powered multiengine airplane and ending with a fully electric configuration with two forms of distributed propulsion and a highly modified wing. These configurations, called Mods, were designed to gain incremental insight into different aircraft propulsion configuration options and their impact on the aircraft performance. The gasoline-powered Mod I configuration consumed 2.6 to 2.9 times more stored energy in cruise than the electric but otherwise conventionally configured Mod II configuration. The highly loaded wing of Mod III led to an increase of 40% in the power-off lift-to-drag ratio as compared to Mod II at the project high-speed cruise target speed and altitude. The power-on lift-to-drag ratio of Mod III was 53% higher than Mod II due to the beneficial aero-propulsive interaction of the wingtip-mounted cruise propellers in Mod III. The high-lift propeller system of Mod IV recovered the low-speed performance of the conventional configuration in Mod II that was otherwise lost with the introduction of the highly loaded Mod III wing. The battery-electric configurations also benefitted from a lack of power lapse in the electric motors with increasing air density as compared to the combustion-powered baseline aircraft.

Distributed Performance↗
NASA NTRSDate not supplied

Flight Performance Estimates for the NASA X-57 Distributed Electric Propulsion Flight Demonstrator

The X-57 flight demonstrator concept featured four configurations starting with a conventional combustion-powered multiengine airplane and ending with a fully electric configuration with two forms of distributed propulsion and a highly modified wing. These configurations, called Mods, were designed to gain incremental insight into different aircraft propulsion configuration options and their impact on the aircraft performance. The gasoline-powered Mod I configuration consumed 2.6 to 2.9 times more stored energy in cruise than the electric but otherwise conventionally configured Mod II configuration. The highly loaded wing of Mod III led to an increase of 40% in the power-off lift-to-drag ratio as compared to Mod II at the project high-speed cruise target speed and altitude. The power-on lift-to-drag ratio of Mod III was 53% higher than Mod II due to the beneficial aero-propulsive interaction of the wingtip-mounted cruise propellers in Mod III. The high-lift propeller system of Mod IV recovered the low-speed performance of the conventional configuration in Mod II that was otherwise lost with the introduction of the highly loaded Mod III wing. The battery-electric configurations also benefitted from a lack of power lapse in the electric motors with increasing air density as compared to the combustion-powered baseline aircraft.

Distributed Performance↗
NASA NTRS1972

Summary analysis of the Gemini entry aerodynamics

The aerodynamic data that were derived in 1967 from the analysis of flight-generated data for the Gemini entry module are presented. These data represent the aerodynamic characteristics exhibited by the vehicle during the entry portion of Gemini 2, 3, 5, 8, 10, 11, and 12 missions. For the Gemini, 5, 8, 10, 11, and 12 missions, the flight-generated lift-to-drag ratios and corresponding angles of attack are compared with the wind tunnel data. These comparisons show that the flight generated lift-to-drag ratios are consistently lower than were anticipated from the tunnel data. Numerous data uncertainties are cited that provide an insight into the problems that are related to an analysis of flight data developed from instrumentation systems, the primary functions of which are other than the evaluation of flight aerodynamic performance.

Whitnah, A. M.↗
NASA NTRS2011

Development of the Orion Crew Module Static Aerodynamic Database: Hypersonic - Part 1

The Orion aerodynamic database provides force and moment coefficients given the velocity, attitude, configuration, etc. of the Crew Exploration Vehicle (CEV). The database is developed and maintained by the NASA CEV Aerosciences Project team from computational and experimental aerodynamic simulations. The database is used primarily by the Guidance, Navigation, and Control (GNC) team to design vehicle trajectories and assess flight performance. The initial hypersonic re-entry portion of the Crew Module (CM) database was developed in 2006. Updates incorporating additional data and improvements to the database formulation and uncertainty methodologies have been made since then. This paper details the process used to develop the CM database, including nominal values and uncertainties, for Mach numbers greater than 8 and angles of attack between 140deg and 180deg. The primary available data are more than 1000 viscous, reacting gas chemistry computational simulations using both the Laura and Dplr codes, over a range of Mach numbers from 2 to 37 and a range of angles of attack from 147deg to 172deg. Uncertainties were based on grid convergence, laminar-turbulent solution variations, combined altitude and code-to-code variations, and expected heatshield asymmetry. A radial basis function response surface tool, NEAR-RS, was used to fit the coefficient data smoothly in a velocity-angle-of-attack space. The resulting database is presented and includes some data comparisons and a discussion of the predicted variation of trim angle of attack and lift-to-drag ratio. The database provides a variation in trim angle of attack on the order of +/-2deg, and a range in lift-to-drag ratio of +/-0.035 for typical vehicle flight conditions.

Bibb, Karen L.↗
NASA NTRS1986

Analytical observations on the aerodynamics of a delta wing with leading edge flaps

The effect of a leading edge flap on the aerodynamics of a low aspect ratio delta wing is studied analytically. The separated flow field about the wing is represented by a simple vortex model composed of a conical straight vortex sheet and a concentrated vortex. The analysis is carried out in the cross flow plane by mapping the wing trace, by means of the Schwarz-Christoffel transformation into the real axis of the transformed plane. Particular attention is given to the influence of the angle of attack and flap deflection angle on lift and drag forces. Both lift and drag decrease with flap deflection, while the lift-to-drag ratioe increases. A simple coordinate transformation is used to obtain a closed form expression for the lift-to-drag ratio as a function of flap deflection. The main effect of leading edge flap deflection is a partial suppression of the separated flow on the leeside of the wing. Qualitative comparison with experiments is presented, showing agreement in the general trends.

Oh, S.↗
NASA NTRS2017

Application of a Fully Numerical Guidance to Mars Aerocapture

An advanced guidance algorithm, Fully Numerical Predictor-corrector Aerocapture Guidance (FNPAG), has been developed to perform aerocapture maneuvers in an optimal manner. It is a model-based, numerical guidance that benefits from requiring few adjustments across a variety of different hypersonic vehicle lift-to-drag ratios, ballistic co-efficients, and atmospheric entry conditions. In this paper, FNPAG is first applied to the Mars Rigid Vehicle (MRV) mid lift-to-drag ratio concept. Then the study is generalized to a design map of potential Mars aerocapture missions and vehicles, ranging from the scale and requirements of recent robotic to potential human and precursor missions. The design map results show the versatility of FNPAG and provide insight for the design of Mars aerocapture vehicles and atmospheric entry conditions to achieve desired performance.

Matz, Daniel A.↗
NASA NTRS2005

A Preliminary Investigation of Aerogravity Assist at Triton for Capture into Orbit About Neptune

Previous work by our group has shown that an aerogravity assist maneuver at the moon Triton might be used to capture a spacecraft into a closed orbit about Neptune if a nominal atmospheric density profile at Triton is assumed. The present study extends that work and examines the impact of atmospheric dispersions, especially important in light of the very low density and large degree of uncertainty of Triton s atmosphere. Additional variables that are analyzed in the current study include ballute size and cut time and variations in the final target orbit. Results indicate that while blunt-body, rigid aeroshells penetrate too closely to the surface to be practical, ballutes of modest size show promise for this maneuver. Future studies will examine the application of inflatable aeroshells and rigid aeroshells with higher lift-to-drag ratios such as biconics and lifting bodies.

Ramsey, Philip↗