Search NASA⌕ Search

SEARCH · Search NASA

Results for “Massachusetts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Defects vibrations engineering for enhancing interfacial thermal transport in polymer composites

To push upper boundaries of thermal conductivity in polymer composites, understanding of thermal transport mechanisms is crucial. Despite extensive simulations, systematic experimental investigation on thermal transport in polymer composites is limited. To better understand thermal transport processes, we design polymer composites with perfect fillers (graphite) and defective fillers (graphite oxide), using polyvinyl alcohol (PVA) as a matrix model. Measured thermal conductivities of ~1.38 ± 0.22 W m -1 K -1 in PVA/defective filler composites is higher than those of ~0.86 ± 0.21 W m -1 K -1 in PVA/perfect filler composites, while measured thermal conductivities in defective fillers are lower than those of perfect fillers. We identify how thermal transport occurs across heterogeneous interfaces. Thermal transport measurements, neutron scattering, quantum mechanical modeling, and molecular dynamics simulations reveal that vibrational coupling between PVA and defective fillers at PVA/filler interfaces enhances thermal conductivity, suggesting that defects in polymer composites improve thermal transport by promoting this vibrational coupling.

42 ENGINEERING↗
DOE OSTI2025

Shear–Mediated Stabilization of Spin Spiral Order in Multiferroic NiI 2

Type-II multiferroicity from non-collinear spin order is recently explored in the van der Waals material NiI 2 . Despite the importance for improper ferroelectricity, the microscopic mechanism of the helimagnetic order remains poorly understood. Here, the magneto-structural phases of NiI 2 are investigated using resonant magnetic X-ray scattering (RXS) and X-ray diffraction. Two competing magnetic phases are identified. Below 60 K, an incommensurate magnetic reflection (q ≈ [0.143,0,1.49] reciprocal lattice units) is observed which exhibits finite circular dichroism in RXS, signaling the inversion symmetry-breaking helimagnetic ground state. At elevated temperature, in the non-polar phase (60 K < T < 75 K), a distinct q ≈ [0.087,0.087,1.5] magnetic order is observed, attributed to a collinear incommensurate (CI) state. The first-order CI-helix transition is concomitant with a structural transition characterized by a significant interlayer shear, which drives the helimagnetic ground state as evidenced by a mean-field Heisenberg model including interlayer exchange and its coupling to the structural distortion. Furthermore, these findings identify interlayer magneto-structural coupling as the key driver behind multiferroicity in NiI 2 .

36 MATERIALS SCIENCE↗
DOE OSTI2025

AI‐Driven Defect Engineering for Advanced Thermoelectric Materials

Thermoelectric materials offer a promising pathway to directly convert waste heat to electricity. However, achieving high performance remains challenging due to intrinsic trade-offs between electrical conductivity, the Seebeck coefficient, and thermal conductivity, which are further complicated by the presence of defects. This review explores how artificial intelligence (AI) and machine learning (ML) are transforming thermoelectric materials design. Advanced ML approaches including deep neural networks, graph-based models, and transformer architectures, integrated with high-throughput simulations and growing databases, effectively capture structure-property relationships in a complex multiscale defect space and overcome the “curse of dimensionality”. This review discusses AI-enhanced defect engineering strategies such as composition optimization, entropy and dislocation engineering, and grain boundary design, along with emerging inverse design techniques for generating materials with targeted properties. Finally, it outlines future opportunities in novel physics mechanisms and sustainability, highlighting the critical role of AI in accelerating the discovery of thermoelectric materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Rigid Supramolecular Aramid Nanotubes as Catalyst Supports

Solution‐phase heterogeneous catalysts benefit from nanoscale dimensions, which maximize specific surface area and enhance catalytic activity. However, the ease of recovering such nanocatalysts depends on the design of the support materials, which are often particle‐like. Rigid 1D nanomaterials are proposed as supports that can enhance separability while offering high volumetric specific surface area for greater catalyst loading and activity. Here, aramid amphiphiles (AAs) are designed to spontaneously self‐assemble in water into high‐aspect‐ratio supramolecular nanotubes with tunable surface chemistry. These AA nanotubes exhibit high persistence lengths (P = 750 ± 340 µm) and mechanical stiffnesses (3 N/m). Incorporating surface thiol groups enables immobilization of catalytic gold nanoparticles. The resulting AA nanotube‐gold nanoparticle complexes exhibit high catalytic activity, efficient recoverability via simple microfiltration, and sustained reusability over ten reaction cycles. This study demonstrates the utility of molecular self‐assembled 1D nanomaterials as versatile scaffolds for the reuse and recovery of nanoscale catalysts.

1D nanomaterials↗
DOE OSTI2024

Oleaginous Yeast Biology Elucidated With Comparative Transcriptomics

ABSTRACT Extremophilic yeasts have favorable metabolic and tolerance traits for biomanufacturing‐ like lipid biosynthesis, flavinogenesis, and halotolerance – yet the connection between these favorable phenotypes and strain genotype is not well understood. To this end, this study compares the phenotypes and gene expression patterns of biotechnologically relevant yeasts Yarrowia lipolytica , Debaryomyces hansenii , and Debaryomyces subglobosus grown under nitrogen starvation, iron starvation, and salt stress. To analyze the large data set across species and conditions, two approaches were used: a “network‐first” approach where a generalized metabolic network serves as a scaffold for mapping genes and a “cluster‐first” approach where unsupervised machine learning co‐expression analysis clusters genes. Both approaches provide insight into strain behavior. The network‐first approach corroborates that Yarrowia upregulates lipid biosynthesis during nitrogen starvation and provides new evidence that riboflavin overproduction in Debaryomyces yeasts is overflow metabolism that is routed to flavin cofactor production under salt stress. The cluster‐first approach does not rely on annotation; therefore, the coexpression analysis can identify known and novel genes involved in stress responses, mainly transcription factors and transporters. Therefore, this work links the genotype to the phenotype of biotechnologically relevant yeasts and demonstrates the utility of complementary computational approaches to gain insight from transcriptomics data across species and conditions.

Weintraub, Sarah J. [Department of Bioinformatics ↗
DOE OSTI2025

Fluorinated Rocksalt‐Polyanion Cathode for Lithium‐Ion Batteries

Integrated rocksalt‐polyanion cathodes (DRXPS) are promising candidates for next‐generation lithium‐ion battery cathode materials that combine high energy density, stable cycling performance, and reduced reliance on Co and Ni. In this work, we investigated Li 3 Mn 1.6 P 0.4 O 5.4 F 0.6 , a new DRXPS cathode with fluoride incorporation. A pure spinel phase was formed and a discharge capacity retention of 84% was achieved after 200 cycles between 1.5 and 4.8 V versus Li/Li + . In comparison, the similarly synthesized Li 3 Mn 1.6 Nb 0.4 O 5.4 F 0.6 , in which all P 5+ was substituted by Nb 5+ while maintaining the same stoichiometry for all other elements, crystallized in a disordered rocksalt structure, and exhibited inferior capacity retention and rate capability than the P 5+ counterpart. Our findings expand the compositional space of DRXPS to include F − , justify the viability of integrating polyanion groups in rocksalt‐type cathodes, and highlight the superiority of P 5+ as a cation charge compensator compared to the commonly used Nb 5+ . This work thereby advances the design of robust, high‐performance cathode materials for sustainable batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Mucus-derived glycans are inhibitory signals for Salmonella Typhimurium SPI-1-mediated invasion

Mucus forms a critical barrier against enteric pathogens like Salmonella enterica serovar Typhimurium. While in vivo studies indicate that secreted, gel-forming mucins and specifically core 3 glycosylation are protective against S. Typhimurium, the molecular mechanisms involved remain unclear. Here, we demonstrate that native intestinal mucins inhibit Salmonella invasion of colonic epithelial cells by downregulating the type 3 secretion system through suppression of the key virulence regulator, HilD. Our study identifies mucin glycans and specific mucin sugars, namely N-acetyl galactosamine and N-acetyl glucosamine, as the components responsible for mucin’s anti-virulence effect, likely via functional or direct interaction with HilD’s putative carbohydrate-binding domain. Notably, we find that the native presentation of these sugars is important for activity. These insights provide a mechanistic foundation for mucin-based strategies to combat enteric infections and, given the prevalence of homologous AraC-type regulators in other pathogens, suggest mucins’ potential as broad-spectrum anti-virulence agents.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2026

Alcoholysis of nylon 6 waste to ε-caprolactam promoted by phosphoric acid

Nylon 6 is widely used in high-performance materials. However, the inherent structural rigidity of nylon 6 inhibits catalytic depolymerization to its monomer, ε-caprolactam. Here, in this study, we demonstrate an acid-catalyzed alcoholysis process that depolymerizes nylon 6 to ε-caprolactam, achieving yields up to 74% using n-propanol as solvent and phosphoric acid as catalyst at 220°C for 2 h. We further applied the process to commercial nylon-containing products, demonstrating ε-caprolactam yields of 67% to 76%. Process modeling and techno-economic analysis estimated a minimum selling price of recycled nylon 6 at $\$$1.79/kg, 30% lower than the 5-year average market price of virgin nylon 6. These estimates depend on assumed costs and process performance and may vary with future conditions. Life cycle assessment indicated that nylon 6 produced via alcoholysis can reduce greenhouse gas emissions by up to 63% compared with primary production. Overall, this study demonstrates a facile, cost-effective, and environmentally beneficial process for nylon 6 chemical recycling.

09 BIOMASS FUELS↗
DOE OSTI2025

Anomalous neutron nuclear-magnetic interference spectroscopy

The electron–phonon interaction plays a critical role in materials’ electrical, thermal, optical, and superconducting properties. However, measuring the phonon mode-resolved electron–phonon interaction has been challenging. Here we propose neutron-scattering-based Anomalous Neutron nUclear-Magnetic Interference Spectroscopy (ANUBIS), where the co-existence of neutron nuclear scattering and magnetic scattering leads to anomalous dynamical structure factor under the presence of the electron–phonon interaction. Such anomalous structure factor is linear in electron–phonon coupling constant at the phonon wavevector, and is directly proportional to the momentum and energy-resolved dielectric function. The experimental configuration can be achieved using existing polarized inelastic neutron scattering setup, and an order-of-magnitude estimate shows the viability to observe the anomalous scattering signal is around to 10 –4 to 10 –3 relative to phonon scattering, which is examined through the preliminary experiments and achievable at emerging neutron facilities. As a result, our proposal offers an alternative neutron-based metrology to probe the crucial electronic properties.

Electron-phonon interactions↗
DOE OSTI2026

Demonstration of an All-Refractory Corrosion-Resistant Molten Salt Pumping and Storage Infrastructure Up to 950 degrees C

Concentrating solar power (CSP) with thermal energy storage (TES) has an estimated cost similar to solar photovoltaics (PV) with lithium-ion batteries (LIB), but CSP + TES has the potential for significantly reduced cost by operating above 700 degrees C. However, this requires a TES medium and containment infrastructure which are chemically compatible and do not degrade above 700 degrees C. MgCl2-KCl-NaCl (MKN) salt is a promising medium, but when MKN salt has small amounts of water and oxygen dissolved in it, it excessively corrodes conventional commercial alloys. Here, we consider refractory materials including graphite, carbon-carbon composite (C/C), and molybdenum because they maintain high mechanical strength at elevated temperatures and are expected to resist corrosion by MKN salt. While selection of refractory materials is often constrained by the need to remain chemically stable in air, this work uses an enclosure filled with inert gas to allow the use of materials like graphite and molybdenum. Notably, graphite components can seal against liquids unlike many brittle refractory materials. We demonstrate a centrifugal pump and mechanical seals made of refractory materials in a laboratory-scale circulation loop, which successfully operated continuously for more than 49 h at temperatures ranging from 750 degrees C to 950 degrees C with no mechanical failures or chemical degradation of the refractory materials. To the best of our knowledge, this is the highest temperature molten salt circulation loop that has been successfully developed, and this refractory infrastructure allows for operation at even much higher temperatures (<1600 degrees C) if a storage medium with a lower vapor pressure is used. The principles of this architecture are relevant to other applications with high temperature flowing metals and salts including Generation IV nuclear fission reactors for power production and molten salt electrolysis reactors for metallurgical processing.

14 SOLAR ENERGY↗
DOE OSTI2025

Architecture-Dependent Thin Film Self-Assembly of Star Polystyrene-poly(2-vinylpyridine) Block Copolymers

Controlling the orientation of nanostructured block copolymer (BCP) thin films is essential for their use in templating, transport, and pattern transfer. Conventional efforts mainly focus on adjusting enthalpic interactions between the blocks and interfaces, while entropic contributions are often overlooked. Here, we show that the morphology of BCP thin films can be precisely tuned by the architectural design of star BCPs. Specifically, we synthesized multiarm star BCPs with a polystyrene (PS) core and poly(2-vinylpyridine) (P2VP) corona, which exhibits a lamellar microdomain morphology. The entropic penalty associated with a parallel orientation of the microdomains to the substrate is controlled by varying the number of arms comprising the star BCPs, from 2-arms (triblock) to 3-arms and 4-arms. We systematically investigated the thin film morphology at different depths using grazing incidence small-angle X-ray and neutron scattering (GISAXS and GISANS), atomic force microscopy (AFM), water contact angle (WCA), and interference microscopy. The results show that 2-arm star BCPs show a parallel orientation, the 3-arm star BCPs form a uniform PS film at the air surface with a vertical orientation of the microdomains underneath, and the 4-arm star BCPs exhibit a parallel microdomain orientation at the air surface with mixed parallel and perpendicular microdomain orientation in the bulk. Additionally, we found that the inclination angle of microdomains at the edges of islands and holes, resulting from the incommensurability between film thickness and the characteristic period of the microdomain morphology, increases with a higher number of arms. This suggests a greater grain boundary tilt angle in the microdomains of star-shaped block copolymers (BCPs). When silicon substrates were modified with PS homopolymer, the selective interaction between substrate and core blocks promotes a parallel orientation for the 4-arm star BCPs. In conclusion, this work shows that control of arm number in star BCPs affords diverse BCP thin film morphologies, offering insights into the star BCP conformations in thin films across different depths.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Warpage-Resistant, Under-Extrusion-Free, High-Surface-Quality Additive Manufacturing Process for Polyethylene-Based Composite Radiation Shielding Material

Polyethylene (PE) is one of the best shielding materials for primary space radiation due to its high hydrogen content. For effective secondary neutron shielding, boron-rich fillers are incorporated to enhance performance. The semicrystalline nature and high thermal expansion coefficient of PE impede its adoption for in situ additive manufacture in space via the fused deposition modeling (FDM) 3D printing. Here, we developed an optimized PE blend to mitigate the effects of under-extrusion and warpage. Guided by studies on extrusion and warpage, we developed an optimal set of printing parameters for the proposed PE blend. The optimum PE blend─both in its pure form and when doped with fillers─has been tested on different FDM printers. The printed structures exhibit high and uniform density, smooth surfaces, no warpage, and competitive mechanical properties. The FDM-printed plates demonstrate efficient shielding from thermal neutrons, predicted via modeling and confirmed experimentally using extended Q-range small-angle neutron scattering.

additive manufacturing↗
DOE OSTI2024

Mixed-Chalcogen 2D Silver Phenylchalcogenides (AgE 1– x E x Ph; E = S, Se, Te)

Alloying is a powerful strategy for tuning the electronic band structure and optical properties of semiconductors. Here, we investigate the thermodynamic stability and excitonic properties of mixed-chalcogen alloys of two-dimensional (2D) hybrid organic-inorganic silver phenylchalcogenides (AgEPh; E = S, Se, Te). Using a variety of structural and optical characterization techniques, we demonstrate that the AgSePh-AgTePh system forms homogeneous alloys (AgSe 1-x Te x Ph, 0 ≤ x ≤ 1) across all compositions, whereas the AgSPh-AgSePh and AgSPh-AgTePh systems exhibit distinct miscibility gaps. Density functional theory calculations reveal that chalcogen mixing is energetically unfavorable in all cases, but comparable in magnitude to the ideal entropy of mixing at room temperature. Because AgSePh and AgTePh have the same crystal structure (which is different from AgSPh), alloying is predicted to be thermodynamically preferred over phase separation in the case of AgSePh-AgTePh, whereas phase separation is predicted to be more favorable than alloying for both the AgSPh-AgSePh and AgSPh-AgTePh systems, in agreement with experimental observations. Homogeneous AgSe1-xTexPh alloys exhibit continuously tunable excitonic absorption resonances in the ultraviolet-visible range, while the emission spectrum reveals competition between exciton delocalization and self-trapping behavior. Altogether, these observations provide new insight into the thermodynamics of 2D silver phenylchalcogenides and the effect of lattice composition on electron-phonon interactions in 2D hybrid organic-inorganic semiconductors.

36 MATERIALS SCIENCE↗
DOE OSTI2025

High-Energy, High-Power Sodium-Ion Batteries from a Layered Organic Cathode

Sodium-ion batteries (SIBs) attract significant attention due to their potential as an alternative energy storage solution, yet challenges persist due to the limited energy density of existing cathode materials. In principle, redox-active organic materials can tackle this challenge because of their high theoretical energy densities. However, electrode-level energy densities of organic electrodes are compromised due to their poor electron/ion transport and severe dissolution. Here, we report the use of a low-bandgap, conductive, and highly insoluble layered metal-free cathode material for SIBs. It exhibits a high theoretical capacity of 355 mAh g –1 per formula unit, enabled by a four-electron redox process, and achieves an electrode-level energy density of 606 Wh kg –1 electrode (90 wt % active material) along with excellent cycling stability. It allows for facile two-dimensional Na+ diffusion, which enables a high intrinsic rate capability. Growth of the active cathode material in the presence of as little as 2 wt % carboxyl-functionalized carbon nanotubes improves charge transport and charge transfer kinetics and further enhances the power performance. Altogether, these allow the construction of SIB cells built from an affordable, sustainable organic small molecule, which provide a cathode energy density of 472 Wh kg –1 electrode when charging/discharging in 90 s and a top specific power of 31.6 kW kg –1 electrode .

36 MATERIALS SCIENCE↗
DOE OSTI2025

Anionic Lipids Regulate the Light-Harvesting Complex 1-Reaction Center Photocycle in Purple Bacteria

Photosynthetic purple bacteria can capture and convert sunlight with a remarkable, nearly 100% quantum efficiency. The light-harvesting complex 1-reaction center (LH1-RC) core complex is the membrane complex fundamentally responsible for solar energy conversion. LH1-RC has a highly conserved surrounding lipid composition known to favor anionic lipids for an unknown function. Here, in this work, we compared experimentally the rate of LH1-to-RC energy transfer in detergent, membrane nanodiscs with varying lipid compositions, purified membrane fragments, and live cells. The energy transfer rate indicated that RC turnover decreased in neutral lipids, yet was partially restored in anionic lipids, revealing an unexpected lipid dependence. In complementary molecular dynamics simulations, the anionic lipid cardiolipin showed electrostatic interactions with LH1-RC that may mediate quinone exchange, providing a mechanism for the observed lipid dependence. Overall, these results revealed that anionic lipids facilitate LH1-RC redox cycling, identifying a functional role for membrane composition in photosynthetic solar energy conversion.

bacteria↗
DOE OSTI2025

Contact with Electrically Conductive Inert Solids Alters Intrinsic Heterogeneous Brønsted Acid Catalysis

Interfacial electric fields at heterogeneous catalyst surfaces have been demonstrated to alter kinetics of liquid-phase reactions. In these systems, electric fields are generated from applying a potential to the catalyst through connection to a potentiostat or through electron transfer from redox-active species in solution. Here, we demonstrate that catalyst polarization can also occur by simply contacting electrically conductive inert solids, leading to the counterintuitive conclusion that a catalyst particle touching an inert solid can alter intrinsic reaction rates. Using dehydration of 1-methylcyclopentanol to 1-methylcyclopentene catalyzed by Brønsted-acidic carboxylic acid groups on carbon nanotubes as a proof-of-concept probe reaction, we show that catalyst contact with inert, thermally reduced carbon nanotubes leads to order-of-magnitude changes in reaction rate. Furthermore, we demonstrate that these contact-induced effects can also be observed under standard laboratory reaction conditions, where particle-to-particle contact in stirred catalyst powder suspensions is sufficient to demote rates by ∼8-fold. This work provides the foundation for a new method of reaction rate control, which could have implications whenever heterogeneous catalyst particles are in contact with inert materials for liquid-phase reactions in the presence of electrolyte.

Alcohols↗
DOE OSTI2025

Piezoelectrically actuated silicon-nitride-based high-speed spatial light modulator

Advancements in light modulator technology have been driving discoveries and progress across various fields. The problem of large-scale coherent optical control of atomic quantum systems—including cold atoms, ions, and solid-state color centers—presents among the most stringent requirements. This motivates a new generation of high-speed large-scale modulator technology operating in the visible to near-infrared wavelength range. We introduce a scalable modulator technology based on piezoelectrically actuated silicon nitride resonant waveguide gratings fabricated on 200 mm diameter silicon wafers with CMOS-compatible processes. We present a proof-of-concept device with 4 × 4 individually addressable 50 μ m × 50 μ m pixels or channels, each containing a resonant waveguide grating with a ~ 780 nm design wavelength, supporting > 100 MHz modulation speeds, and a spectral response with > 20 dB extinction.

integrated optics↗