Search NASA⌕ Search

SEARCH · Search NASA

Results for “Matrix diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Corrosion of 316 L stainless steel under the natural circulation of molten NaCl-MgCl 2 salt

The corrosion behavior of 316 L stainless steel (SS) was studied via the natural circulation of molten eutectic NaCl-MgCl 2 salt through a microloop. The post-corrosion tested 316 L SS microloop sections were characterized with microscopy techniques to determine the microstructural and microchemical changes that occurred at the alloy/salt interface. It was found that 316 L SS showed heterogeneous dissolution at the hot-leg, whereas deposition of corrosion products occurred at the cold-leg. For the first time, experimentally obtained molten salt flow-induced corrosion of 316 L SS results were combined with computational thermodynamic-kinetic models to validate the dissolution and deposition in terms of elemental compositional changes at the alloy/salt interface. The thermodynamic-kinetic modeling predicted that the heterogeneous dissolution of Cr and Fe from the hot-leg section of 316 L SS persisted throughout the salt circulation. The model also estimated that, despite Cr deposition starting earlier than Fe, the total redeposition of Fe is expected to be significantly greater than that of Cr over the circulation of salt. Furthermore, the modeling accurately predicted the subsurface enrichment of Mo which is attributed to the reduced Cr activity and the relatively higher diffusion rate of Mo within the alloy matrix. Here, the agreement between modeling and experimental results confirms that Fe chlorides dissolve at the hot-leg and subsequently deposit at the cold-leg due to activity changes driven by the thermal gradient. By contrast, Cr was not detected in the cold-leg deposits, which is attributed to its weaker temperature dependence on activity, limiting its redeposition under these conditions.

36 - MATERIALS SCIENCE↗

Characterization of γ′/γ″ compact and sandwich type precipitates during long-term high-temperature exposure in Ni-based superalloys

Here, the formation of γ′/γ″ co-precipitates is investigated in Ni-based superalloys with a varying Ti/Al ratio and Ta content and their stability is studied using long-term high-temperature exposure. Transmission electron microscopy and atom probe tomography analyses demonstrate that both higher Ti/Al ratios and increased Ta promote γ″ phase formation, leading to sandwich and compact structures. The compact co-precipitation significantly reduces γ′ precipitate coarsening during 10,000 h exposure at 700°C by restricting elemental diffusion, particularly of aluminum, from the γ matrix to the γ′ phase. For the alloy without a compact structure, and only γʹ precipitates, at the beginning of the exposure, the coarsening rate over 10,000 h was 3.5 times faster than for the alloy with compact γʹ/γʺ precipitates. Evidence of destabilization of the compact morphology was found to occur between 5,000 and 10,000 h exposure and originated from the extensive formation and growth of δ platelets that extended throughout the grains. Thus, the outer layer of the compact, which consists of γʺ, was subjected to the γ″ to δ phase transformation.

gamma double prime↗

How Processing Atmosphere Influences the Evolution of GeO[subscript 2]-Embedded Germanium Nanocrystals Obtained from the Thermolysis of Phenyl Trichlorogermane-Derived Polymers

We report the influence of processing atmosphere on the evolution of oxide-embedded germanium nanocrystals (Ge-NCs) formed by the thermal processing of (C{sub 6}H{sub 5}GeO{sub 1.5}){sub n} sol-gel polymers. In an inert processing atmosphere (100% Ar), the generation of elemental Ge from thermally induced disproportionation of the germanium rich oxide (GRO) leads to GeO{sub 2}-embedded Ge-NCs whose size is independent of peak processing temperature and time. Processing in a slightly reducing atmosphere (5% H{sub 2}/95% Ar) activates a second Ge-NC formation and growth pathway, involving the reduction of Ge oxide species. Here, we report that the processing atmosphere governs the distribution of Ge species. By modifying the contributions from redistribution and reduction reactions within the GRO, diffusion of Ge atoms throughout the oxide matrix and formation and growth of Ge-NCs are impacted.

36 MATERIALS SCIENCE↗

A general synthesis of single atom catalysts with controllable atomic and mesoporous structures

The control of single metal atomic sites has been extensively studied in the field of single atom catalysts. By contrast, the precise control of the mesoporous structure in the matrix material, which directly correlates with mass diffusions and may play a dominant role in delivering industrially relevant reaction rates, has been overlooked. In this work, we report a general method for the synthesis of a single atom catalyst with control of the atomic structure of the single atomic site as well as the mesoporous structure of the carbon support for optimized catalytic performance. Various combinations of metal centres (Ni, Co, Mn, Zn, Cu, Sc and Fe) and mass diffusion channels in two dimensions and three dimensions were achieved. Using CO 2 reduction to CO as an example, our Ni single atom catalyst with three-dimensional diffusion channels delivered a practical current of 350 mA cm –2 while maintaining a 93% CO Faradaic efficiency, representing a sixfold improvement in turnover frequency compared to two-dimensional counterparts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of post-deposition heat treatment on electrodeposited NiCoCrAlY coatings

An electrolytic process was utilised to fabricate NiCoCrAlY coatings, involving deposition of a composite coating consisting of the (Ni,Co) matrix and CrAlY particles, followed by a diffusion heat treatment to convert the composite coating to the desired NiCoCrAlY microstructure. This study focused on the effects of the post-deposition heat-treating conditions (temperature and atmosphere) on the final coating microstructure and composition. The (Ni,Co)–CrAlY composite coatings were heat-treated for 2 h at 1000, 1100 and 1200°C in vacuum and Ar, respectively. Phase constituents and concentrations of the major elements in the coating after heat treatment were examined. Vacuum heat treatment at temperatures ≥1100°C resulted in a significant decrease in Cr content at the coating surface due to Cr evaporation. Heat treatment at 1200°C also caused outward diffusion of Ti from the substrate alloy to the coating layer.

Zhang, L. Z.↗

MICROSTRUCTURE EVOLUTION MODELING FOR SOLUTION TREATMENT OF ALUMINUM ALLOYS

The microstructure evolution during solution treatment plays an important role in mechanical properties of heat-treated aluminum alloys. In this paper, models were reviewed that can predict the microstructure evolution during the solutionizing process of the aging heat treatment of aluminum alloys. The dissolution of Mg2Si particles has been modeled as a diffusion process of Mg in the -Al matrix. The evolution of volumetric fraction of fragmented silicon as a function of time and temperature was also considered. The growth and coarsening of silicon particles during the heat treatment was considered. It was found that constitutive equations and required property data for most of the phenomena that need to be considered are available. Several model parameters that need to be obtained from material characterization were identified. Pending the availability of these model parameters, this comprehensive model can be used to describe the microstructure evolution of aluminum alloys in order to optimize the solutionizing heat treatment for energy savings.

Yin, Hebi↗

Retention of Anionic Species on Granite: Influence of Granite Composition - 12129

Technetium (Tc-99, T{sub 1/2} = 2.1.10{sup 5} yrs) and selenium (Se-79, T{sub 1/2} = 6.5.10{sup 4} yrs) belong among fission products, being produced by fission of nuclear fuel. Both elements can significantly contribute to risk due to their complicated chemistry, long life times, high mobility and prevailing anionic character. Therefore, knowledge of migration behaviour under different conditions can significantly improve input into performance and safety assessment models. Granite is considered as a potential host rock for deep geological disposal of radioactive waste in many countries. Granitic rocks consist usually of quartz, feldspar, plagioclase (main components), mica, chlorite, kaolinite (minor components). The main feature of the rock is advection governed transport in fractures, complemented with diffusion process from fracture towards undisturbed rock matrix. The presented work is focused on interaction of anionic species (TcO{sub 4}{sup -}, SeO{sub 4}{sup 2-}, SeO{sub 3}{sup 2-}) with granitic rock. Furthermore, the importance of mineral composition on sorption of anionic species was also studied. The batch sorption experiments were conducted on the crushed granite from Bohemian Massive. Five fractions with defined grain size were used for static batch method. Mineral composition of each granitic fraction was evaluated using X-ray diffraction. The results showed differences in composition of granitic fractions, even though originating from one homogenized material. Sorption experiments showed influence of granite composition on adsorption of both TcO4{sup -} and SeO3{sup 2-} on granitic rock. Generally, Se(IV) showed higher retention than Tc(VII). Se(VI) was not almost sorbed at all. Fe containing minerals are pronounced as a selective Se and Tc sorbent, being reduced on their surface. As micas in granite are usually enriched in Fe, increased sorption of anionic species onto mica enriched fractions can be explained by this reason. On the other hand, fractions enriched in feldspar did not show increased sorption affinity to Tc and Se. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Modeling of fission gas diffusion and release for Gd 2 O 3 doped UO 2

Uranium dioxide (UO 2 ) is the primary nuclear fuel in light water reactors, and its excess neutronic reactivity can be controlled by adding burnable absorbers, such as Gd 2 O 3 . This burnable absorber has a large neutron absorption cross-section, lowering the high reactivity of the reactor's initial fuel load. However, there needs to be more understanding of how added Gd 2 O 3 influences the properties of UO 2 under irradiation. To understand the behavior of defects and fission gas in the UO 2 /Gd 2 O 3 system under irradiation, we use cluster dynamics modeling supported by density functional theory calculations. First, we calculate the formation energies of Gd point and cluster defects, and evaluate the temperature-dependent defect concentrations using the defect formation energies and entropies. We show that Gd is soluble in UO 2 , introducing a negative charge in the system. Using this information, we adapted the cluster dynamics code Centipede to model the influence of Gd on U self-diffusion and Xe diffusion in UO 2 with 10 wt% Gd 2 O 3 . Also, we analyzed the Xe diffusion as a function of Gd 2 O 3 concentration, showing that the Xe diffusivity is decreased, which means that the athermal diffusivity due to electronic stopping persists at higher temperatures. In conclusion, the decrease in Xe diffusion means that more Xe stays in the matrix, decreasing the Xe release, and lowering its influence of fission gas release on the thermomechanical properties of UO 2 .

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructural and compositional characterization of terbium-doped Nd-Fe-B sintered magnets

Anisotropic sintered magnets based on the Nd{sub 2}Fe{sub 14}B phase doped with Tb were prepared using a grain-boundary diffusion process (GBDP) in order to enhance their coercivity. A FEGSEM microstructural analysis revealed that these GBDP magnets had a core-shell structure, where thin, Tb-rich, (NdTb){sub 2}Fe{sub 14}B shells are formed on the original matrix Nd{sub 2}Fe{sub 14}B grains after diffusion of the Tb. This shell thickness varies from a few tens of nanometres in the middle of the magnet up to a few micrometers near the edge. The exact chemical composition of these shells was determined using EDS and WDS electron-probe microanalyses, which were modified and optimized for submicrometer scale analyses. When analyzing the common Nd-L{alpha}, Tb-L{alpha} and Fe-K{alpha} lines a mutual multiple overlap in the EDS spectra is present and, as a result, an accurate quantitative analysis was only feasible when using WDS. Using this technique we were able to achieve a lateral analytical resolution of 0.4 {mu}m. A further improvement in resolution, down to 0.15 {mu}m, was realized with a dedicated set-up using low-voltage EDS, analyzing the 'atypical' low-energy Nd-M{alpha}, Tb-M{alpha} and Fe-L{alpha} lines. Quantitative analyses confirmed that the reaction phase (Nd{sub x}Tb{sub 1} {sub -x}){sub 2}Fe{sub 14}B is formed after the diffusion of Tb with the equilibrium concentration of Tb being equal to x Almost-Equal-To 0.5, i.e., with the atomic ratio of Nd/Tb equal to 1/1. We also found that a relatively sharp Tb concentration gradient from the shell to the core occurs within a length of Almost-Equal-To 0.5 {mu}m, while the Fe concentration remains unchanged. In terms of magnetic properties, the Tb-doping significantly increased coercivity by Almost-Equal-To 30% while the remanence remained at the same value as in the undoped Nd-Fe-B. - Highlights: Black-Right-Pointing-Pointer Nd-Fe-B sintered magnets were doped with Tb using grain-boundary diffusion process. Black-Right-Pointing-Pointer A tiny core-shell reaction phase was formed around the Nd{sub 2}Fe{sub 14}B matrix grains. Black-Right-Pointing-Pointer EDS and WDS analyses confirmed (Nd{sub 0.5}Tb{sub 0.5}){sub 2}Fe{sub 14}B equilibrium shell composition. Black-Right-Pointing-Pointer Coercivity of Tb-doped Nd-Fe-B increases by 30% without a drop in remanence.

36 MATERIALS SCIENCE↗

Post-irradiation Experiment on IG-110 and A3-3 Graphites for HTGR - 18494

The first irradiation test of A3-3 graphite matrix and IG-110 graphite were performed in Hanaro during the period of August 2013 through March 2014. The dimensional and weight changes, microstructure, and thermal diffusivity were investigated in different directions of the specimen after the irradiation. Interestingly, the density of the A3-3 matrix was increased by 9.4% due to the weight increase after the irradiation. Moreover, the thermal diffusivity in the radial direction of the A3-3 matrix is almost 3-times higher than that of the axial direction owing to the radially oriented graphite texture shown in the microstructure. Meanwhile, 10-20 {mu}m sized irradiation induced pores are observed in the microstructure of IG-110. The thermal diffusivity measurement of pre- and post-irradiated IG-110 results in a 68% irradiation-dominant decrease of thermal conductivity. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Modeling of the Flows of Admixtures in a Random Layered Strip with Probable Arrangement of Inclusions Near the Boundaries of the Body

We study the random flow of admixtures in a two-phase stochastically inhomogeneous strip with the most probable arrangement of inclusions in the vicinity of the surfaces of the body. A mathematical model is formulated for the function of diffusion flow with nonzero constant initial concentration. A random diffusion flow is represented in the form of a Neumann series. The procedure of averaging of the random mass flow over the ensemble of phase configurations with arcsine distribution function is performed. The influence of the characteristics of the medium on the distribution of mass flow is analyzed. It is shown that if the diffusion coefficient of admixtures in the inclusion is higher than for the matrix, then the increase in the characteristic thickness of the layers causes a decrease in the value of the diffusion flow, whereas the mass flow in the entire body increases with the volume fraction of the inclusions.

97 MATHEMATICS AND COMPUTING↗

Diffusive parameters of tritiated water and uranium in chalk

The Cretaceous Chalk of North-western Europe exhibits a double porosity (matrix and fracture) providing pathways for both slow and rapid flow of water. The present study aims at understanding and predicting the contaminant transfer properties through a significant section of this formation, with a particular emphasis on diffusion. This requires to study the nature of porosity and to perform diffusion experiments in representative samples using uranium and tritiated water (HTO), respectively taken as a reactive tracer and an inert one. The diffusive parameters, i.e. the accessible porosity and the effective diffusion coefficient were determined. Additional information was obtained with mercury porosimetry, gravimetric water content, textural and mineralogical characterization. The diffusion tests performed with HTO appear to be the best method to measure the total accessible porosity in any type of porous media, especially those having large pore size distributions. Our study demonstrates that classical gravimetric water content measurements are not sensitive to the reduction in pore size as opposed to HTO diffusion tests because capillary water is not extracted by conventional gravimetric method but can still be probed by diffusion experiments. We found effective diffusion coefficients D{sub e}(U(VI)) near 4 x 10{sup -10} m{sup 2}s{sup -1}). The slower migration of U(VI) compared to HTO indicates sorption, with R{sub d}(U(VI)) from 100 to 360 mL g{sup -1}. These values are one order of magnitude larger than other determinations of the U(VI) sorption coefficient because only the matrix porosity is concerned here. The migration of U(VI) in chalk is only limited by sorption on ancillary Fe-Pb-bearing minerals. Transport of HTO and U(VI) is independent of the porosity distribution. Uranium diffusion in the chalk matrix porosity is fast enough to allow the total invasion of the pore space within characteristic time scales of the order of 1000 years. This results in a partitioning of uranium velocities in fracture flow and matrix flow proportionally to the respective fracture and matrix porosities. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Monte Carlo calculation of the neoclassical transport matrix by the Einstein-Helfand relation in nonaxisymmetric toroidal plasmas

A Monte Carlo method that calculates the neoclassical transport matrix with the pitch-angle scattering approximation is described for nonaxisymmetric toroidal plasmas. The numerical scheme is based on the Einstein-Helfand relation, which generalizes the calculation of the neoclassical diffusion coefficient with the mean-square displacement. By calculating all the elements of the transport matrix simultaneously, not only the neoclassical diffusion, but also the parallel, poloidal, and toroidal viscosity coefficients can be evaluated for three-dimensional magnetic-field configurations. The newly developed Monte Carlo code is benchmarked favorably for an l=2 single-helicity model against the results of the variational principle.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Multiscale Thermomechanical Damage Model with Internal State Variables for Ceramic Matrix Composites

A length scale-dependent matrix damage model has been developed to simulate the response of ceramic matrix composites (CMCs). This model captures damage initiation and propagation in the brittle matrix material by employing internal state variable (ISV) theory within a multiscale modeling framework to obtain damaged matrix stress-strain constitutive relationships at each length scale. Material degradation due to matrix cracking is captured by a damage variable determined using fracture mechanics and the self-consistent scheme. An additional state variable is introduced to capture the nucleation and growth of matrix porosity, a key mechanism contributing to matrix nonlinearity. Porosity occurs as a result of material diffusion around grain boundaries and the growth of the porosity state variable is related to the material entropy dissipation and the volumetric strain. The nonlinear predictive capabilities of the material model are demonstrated for monolithic silicon carbide, unidirectional (UD) carbon fiber/silicon carbide matrix (C/SiC) CMC, and five-harness satin (5HS) woven C/SiC CMC.

Skinner, Travis D.↗

Temperature Quenching and Fluorescence Depolarization of Carbon Nanodots Obtained via Paraffin Pyrolysis

A temperature effect on fluorescence intensity and polarization of a colloidal system of carbon nanodots in glycerol under linearly polarized pumping conditions is studied. Nanodots are obtained via pyrolysis of paraffin in nanopores of a mesoporous silica. An increase in temperature leads to quenching of nanodots fluorescence, and activation energy of the quenching process is assessed. An experimental relationship between the linear fluorescence polarization and temperature is described by the Levshin–Perrin equation, which takes into account the rotational diffusion of luminescent particles (fluorophores) in a liquid matrix. The size of fluorophores is noticeably smaller than that of carbon nanodots according to the Levshin–Perrin model. A difference between the dimensions of the fluorophore and the nanodot indicates that the small atomic groups responsible for luminescence of the nanodot possess high segmental mobility.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A new approach to enforcing discrete maximum principles in continuous Galerkin methods for convection-dominated transport equations

This work introduces a set of design principles and new algorithmic tools for enforcing maximum principles and/or positivity preservation in continuous finite element approximations to convection-dominated transport problems. Enabling a linear first-order advection equation as a model problem, we address the design of first-order artificial diffusion operators and their higherorder counterparts at the element matrix level. The proposed methodology leads to a nonlinear high-resolution scheme capable of resolving moving fronts and internal/boundary layers as sharp localized nonoscillatory features. The amount of numerical dissipation depends on the difference between the solution value at a given node and a local maximum or minimum. The shockcapturing numerical diffusion coefficient is designed to vanish as the nodal values approach a mass-weighted or linearity-preserving average. The universal applicability and simplicity of the element-based limiting procedure makes it an attractive alternative to edge-based algebraic flux correction.

Kuzmin, D.↗

Characterizing acid diffusion lengths in chemically amplified resists from measurements of deprotection kinetics

The acid-catalyzed deprotection of glassy poly(4-hydroxystyrene-co-tertbutyl acrylate) films was studied with infrared absorbance spectroscopy and stochastic simulations. Experimental data were interpreted with a simple description of subdiffusive acid transport coupled to second-order acid loss. This model predicts key attributes of observed deprotection rates, such as fast reaction at short times, slow reaction at long times, and a nonlinear dependence on acid loading. Fickian diffusion is approached by increasing the post-exposure bake temperature or adding plasticizing agents to the polymer resin. These findings demonstrate that acid mobility and overall deprotection kinetics are coupled to glassy matrix dynamics. To complement the analysis of bulk kinetics, acid diffusion lengths were calculated from the anomalous transport model and compared with nanopattern line widths. The consistent scaling between experiments and simulations suggests that the anomalous diffusion model could be further developed into a predictive lithography tool.

Patil, Abhijit A.↗

High-Temperature Galling Characteristics of Ti-6Al-4V with and without Surface Treatments

Galling is a severe form of surface damage in metals and alloys that typically arises under relatively high normal force, low-sliding speed, and in the absence of effective lubrication. It can lead to macroscopic surface roughening and seizure. The occurrence of galling can be especially problematic in high-temperature applications like diesel engine exhaust gas recirculation system components and adjustable turbocharger vanes, because suitable lubricants may not be available, moisture desorption promotes increased adhesion, and the yield strength of metals decreases with temperature. Oxidation can counteract these effects to some extent by forming lubricative oxide films. Two methods to improve the galling resistance of titanium alloy Ti-6Al-4V were investigated: (a) applying an oxygen diffusion treatment, and (b) creating a metal-matrix composite with TiB2 using a high-intensity infrared heating source. A new, oscillating three-pin-on-flat, high-temperature test method was developed and used to characterize galling behavior relative to a cobalt-based alloy (Stellite 6B ). The magnitude of the oscillating torque, the surface roughness, and observations of surface damage were used as measures of galling resistance. Owing to the formation of lubricative oxide films, the galling resistance of the Ti-alloy at 485o C, even non-treated, was considerably better than it was at room temperature. The IR-formed composite displayed reduced surface damage and lower torque than the substrate titanium alloy.

33 ADVANCED PROPULSION SYSTEMS↗