Search NASA⌕ Search

SEARCH · Search NASA

Results for “Modal Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Level of effort

The generation of a planar model of the ground test experiment structure is examined. This was done by adapting an in-house modal analysis code (Gimbalflex) to allow placement of sensors and actuators at certain locations on the structure. The next step in the development of this model was to adapt if for use with the control pole placement algorithm. The uncontrollable rigid body mode was removed from the model. This uncontrollable mode was due to the pointing of the gimbal. Control system design for the planar model was also initiated. A digital controller was planned utilizing the Control Pole Placement technique. The existence of rate of state feedback was assumed. Once this controller and other control algorithms were developed, it became necessary to conduct speed tests. A study was then made of additional hardware/software necessary to meet the speed requirement.

Source record↗
NASA NTRS1985

An Overview of Latest Model Reduction and Control Methods of Large Flexible Space Structures

The latest trends and theoretical developments involved with the modeling and control of Large Flexible Space Structures (LFSS) are described. The paper addresses first the basic problems, characteristics, and difficulties inherent in modeling and control of LFSS. Major sources of difficulties and errors are the stiffness and damping operators of the dynamic model. Extensions of Linear Quadratic Gaussian (LQG) theory as applied to LFSS are presented, including frequency-shaped cost functionals and perturbation methods. The minimum data/maximum entropy approach which uses a stochastic design model to overcome difficulties found in the LQG-based methods is described. Latest trends in system theory including balanced realization and singular-value analysis are used to determine reduced order controllers and models. Ad hoc methods such as component cost analysis and modal cost analysis are discussed in context with the closed-loop reduction problem of controller order versus performance. The minimum data/maximum entropy approach also addresses controller order versus performance. Those areas of control science and large scale systems that appear to have an important role in understanding and solving LFSS modeling and control are also identified.

Santiago, J. M.↗
NASA NTRS1985

Coupled transient response of tiles bonded elastically to a finite flexible plate

Presented are several methods to study a system of tiles bonded elastically to a finite flexible plate responding to an impulse. First, a one-dimensional (1-D) approximation to the system is constructed using Timoshenko beam theory and transfer matrices. This simulates a strip one tile wide. Modal analysis determines the transient response to an impulse of short duration. Also presented are parametric studies of the effect of bond stiffness and the effect of stiffening from inplane stresses produced by large out-of-plane deflections. A two-dimensional (2-D) model is constructed from the eigenfunctions of the 1-D model in a Galerkin method using pairwise products of the 1-D modes as trial functions. Comparison of the two models establishes a factor applied to peak impulse pressure for results to agree.

El-Raheb, M.↗
NASA NTRS1985

Modal response and noise transmission of composite panels

Noise transmission through flat, angular, fiber-reinforced composite panels is investigated experimentally and analytically. A modal decomposition technique was used to obtain solutions to the governing differential equation of motion. Experimental modal analysis was performed in order to confirm the theoretical results. The test specimens were cross-ply and angle-ply composite panels made of various concentrations of fiberglass, graphite, or aramid fibers embedded in epoxy resion. The experimental results showed good agreement with the theoretical calculations. Graphs of the transmission loss characteristics of the different composite panels are provided.

Grosveld, F. W.↗
NASA NTRS1985

Analytical study of acoustic response of a semireverberant enclosure with application to active noise control

The acoustic response of a semireverberant enclosure with two interacting, velocity-prescribed source distributions was analyzed using standard modal analysis techniques with a view toward a better understanding of active noise control. Different source and enclosure dimensions, source separations, and single-wall admittances were studied over representative frequency bandwidths of 10 Hz with source relative phase as a parameter. Results indicate that power radiated into the enclosure agree qualitatively with the spatial average of the mean square pressure, even though the reverberant field is nondiffuse. Decreases in acoustic power can therefore be used to estimate global noise reduction in a nondiffuse semireverberant environment. As might be expected, parametric studies indicate that maximum power reductions of up to 25 dB can be achieved when secondary and primary sources are compact and closely spaced. Although less success is achieved with increasing frequency and source separation or size, significant suppression of up to 8 dB still occurs over the 1 to 2 Hz bandwidth.

Parrott, T. L.↗
NASA NTRS1983

Turbofan aft duct suppressor study program listing and user's guide

A description of the structure of the Annular Flow Duct Program (AFDP) for the calculation of acoustic suppression due to treatment in a finite length annular duct carrying sheared flow is presented. Although most appropriate for engine exhaust ducts, this program can be used to study sound propagation in any duct that maintains annular geometry over a considerable length of the duct. The program is based on the modal analysis of sound propagation in ducts with axial segments of different wall impedances. For specified duct geometry, wall impedance, flow and acoustic conditions in the duct (including mode amplitude distribution of the source) and duct termination reflection characteristics, the program calculates the suppression due to the treatment in the duct. The presence of forward and backward traveling modes in the duct due to the reflection and redistribution of modes at segment interfaces and duct end terminations are taken into account in the calculations. The effects of thin wall boundary layers (with a linear or mean flow velocity profile) on the acoustic propagation are also included in the program. A functional description of the major subroutines is included and a sample run is provided with an explanation of the output.

Joshi, M. C.↗
NASA NTRS1985

Rotor/bearing system dynamic stiffness measurements

Sweep perturbation testing as used in Modal Analysis when applied to a rotating machine has to take into consideration the machine dynamic state of equilibrium at its operational rotative speed. This stands in contrasts to a static equilibrium of nonrotating structures. The rotational energy has a significant influence on rotor dynamic characteristics. The best perturbing input for rotating machines is a forward or reverse rotating, circular force applied directly to the shaft. Determination of Dynamic Stiffness Characteristics of the rotor bearing system by nonsynchronous perturbation of a symmetric rotating shaft supported in one relatively rigid and one oil lubricated bearing.

Muszynska, A.↗
NASA NTRS1985

Gain saturation effects in supermodes of phase-locked semiconductor laser arrays

A basic modal analysis that includes gain saturation effects in phase-locked semiconductor laser arrays is presented. For a particular supermode operation, different lasers in the array emit different amounts of light, and hence their (waveguide) propagation constants are modified differently. Solving the lasers' rate equations self-consistently with the coupled-mode wave equations seems to provide an answer that is in much better agreement with experimental results than the result using only the coupled-mode analysis.

Katz, J.↗
NASA NTRS1985

Interactive computer graphics and its role in control system design of large space structures

This paper attempts to show the relevance of interactive computer graphics in the design of control systems to maintain attitude and shape of large space structures to accomplish the required mission objectives. The typical phases of control system design, starting from the physical model such as modeling the dynamics, modal analysis, and control system design methodology are reviewed and the need of the interactive computer graphics is demonstrated. Typical constituent parts of large space structures such as free-free beams and free-free plates are used to demonstrate the complexity of the control system design and the effectiveness of the interactive computer graphics.

Reddy, A. S. S. R.↗
NASA NTRS1986

Ragland - An LL3.4 chondrite find from New Mexico

The Ragland, New Mexico, chondrite was found in 1978. It consists of a single stone of 12.16 kg that broke into three pieces. The stone is moderately weathered and has a pronounced chondritic texture. Bulk composition favors an LL classification, and modal analysis and oxygen isotopic composition are consistent with this. The thermoluminescence sensitivity of 0.056 + or - 0.020 normalized to Dhajala, compositional variability of olivine (mean Fa 18.3, sigma = 10.1) and low-Ca pyroxene (mean Fs 14.6, sigma = 6.7), and Ca concentrations in olivine indicate metamorphic subtype 3.4 + or - 0.1. The isotopically heavy oxygen composition, which is characteristic of subtypes 3.0-3.1, may be a primary characteristic and not a result of weathering. Low concentrations of radiogenic Ar-40 and planetary Ar-36 suggest noble gas loss.

Recca, S. I.↗
NASA NTRS1987

Structural dynamics system model reduction

Loads analysis for structural dynamic systems is usually performed by finite element models. Because of the complexity of the structural system, the model contains large number of degree-of-freedom. The large model is necessary since details of the stress, loads and responses due to mission environments are computed. However, a simplified model is needed for other tasks such as pre-test analysis for modal testing, and control-structural interaction studies. A systematic method of model reduction for modal test analysis is presented. Perhaps it will be of some help in developing a simplified model for the control studies.

Chen, J. C.↗
NASA NTRS1988

Minimum weight design of rectangular and tapered helicopter rotor blades with frequency constraints

The minimum weight design of a helicopter rotor blade subject to constraints on coupled flap-lag natural frequencies has been studied. A constraint has also been imposed on the minimum value of the autorotational inertia of the blade in order to ensure that it has sufficient inertia to autorotate in the case of engine failure. The program CAMRAD is used for the blade modal analysis and CONMIN is used for the optimization. In addition, a linear approximation analysis involving Taylor series expansion has been used to reduce the analysis effort. The procedure contains a sensitivity analysis which consists of analytical derivatives of the objective function and the autorotational inertia constraint and central finite difference derivatives of the frequency constraints. Optimum designs have been obtained for both rectangular and tapered blades. Design variables include taper ratio, segment weights, and box beam dimensions. It is shown that even when starting with an acceptable baseline design, a significant amount of weight reduction is possible while satisfying all the constraints for both rectangular and tapered blades.

Chattopadhyay, Aditi↗
NASA NTRS1988

Minimum weight design of rotorcraft blades with multiple frequency and stress constraints

Minimum weight designs of helicopter rotor blades with constraints on multiple coupled flap-lag natural frequencies are studied. Constraints are imposed on the minimum value of the blade autorotational inertia to ensure sufficient rotary inertia to autorotate in case of engine failure and on stresses to guard against structural failure due to blade centrifugal forces. Design variables include blade taper ratio, dimensions of the box beam located inside the airfoil and magnitudes of nonstructural weights. The program CAMRAD is used for the blade modal analysis; the program CONMIN is used for the optimization. A linear approximation involving Taylor series expansion is used to reduce the analysis effort. The procedure contains a sensitivity analysis consisting of analytical derivatives for objective function and constraints on autorotational inertia and stresses. Central finite difference derivatives are used for frequency constraints. Optimal designs are obtained for both rectangular and tapered blades. Using this method, it is possible to design a rotor blade with reduced weight, when compared to a baseline blade, while satisfying all the imposed design requirements.

Chattopadhyay, Aditi↗
NASA NTRS1988

Minimum weight design of rectangular and tapered helicopter rotor blades with frequency constraints

The minimum weight design of a helicopter rotor blade subject to constraints on coupled flap-lag natural frequencies has been studied. A constraint has also been imposed on the minimum value of the autorotational inertia of the blade in order to ensure that it has sufficient inertia to aurorotate in the case of engine failure. The program CAMRAD is used for the blade modal analysis and CONMIN is used for the optimization. In addition, a linear approximation analysis involving Taylor series expansion has been used to reduce the analysis effort. The procedure contains a sensitivity analysis which consists of analytical derivatives of the objective function and the autorotational inertia constraint and central finite difference derivatives of the frequency constraints. Optimum designs have been obtained for both rectangular and tapered blades. Design variables include taper ratio, segment weights, and box beam dimensions. It is shown that even when starting with an acceptable baseline design, a significant amount of weight reduction is possible while satisfying all the constraints for both rectangular and tapered blades.

Chattopadhyay, Aditi↗
NASA NTRS1989

Static and dynamic deflection studies of the SRM aft case-nozzle joint

The redesign of the joints on the solid rocket motor (SRM) has prompted the need for analyzing the behavior of the joints using several different types of analyses. The types of analyses performed include modal analysis, static analysis, transient response analysis, and base driving response analysis. The forces used in these analyses to drive the mathematical model include SRM internal chamber pressure, nozzle blowout and side forces, shuttle vehicle lift-off dynamics, SRM pressure transient rise curve, gimbal forces and moments, actuator gimbal loads, and vertical and radial bolt preloads. The math model represented the SRM from the aft base tangent point (1,823.95 in) all the way back to the nozzle, where a simplified, tuned nozzle model was attached. The new design used the radial bolts as an additional feature to reduce the gap opening at the aft dome/nozzle fixed housing interface.

Christian, David C.↗
NASA NTRS1989

On damping mechanisms in beams

A partial differential equation model of a cantilevered beam with a tip mass at its free end is used to study damping in a composite. Four separate damping mechanisms consisting of air damping, strain rate damping, spatial hysteresis and time hysteresis are considered experimentally. Dynamic tests were performed to produce time histories. The time history data is then used along with an approximate model to form a sequence of least squares problems. The solution of the least squares problem yields the estimated damping coefficients. The resulting experimentally determined analytical model is compared with the time histories via numerical simulation of the dynamic response. The procedure suggested here is compared with a standard modal damping ratio model commonly used in experimental modal analysis.

Banks, H. T.↗
NASA NTRS1989

Shooting and bouncing rays - Calculating the RCS of an arbitrarily shaped cavity

A ray-shooting approach is presented for calculating the interior radar cross section (RCS) from a partially open cavity. In the problem considered, a dense grid of rays is launched into the cavity through the opening. The rays bounce from the cavity walls based on the laws of geometrical optics and eventually exit the cavity via the aperture. The ray-bouncing method is based on tracking a large number of rays launched into the cavity through the opening and determining the geometrical optics field associated with each ray by taking into consideration (1) the geometrical divergence factor, (2) polarization, and (3) material loading of the cavity walls. A physical optics scheme is then applied to compute the backscattered field from the exit rays. This method is so simple in concept that there is virtually no restriction on the shape or material loading of the cavity. Numerical results obtained by this method are compared with those for the modal analysis for a circular cylinder terminated by a PEC plate. RCS results for an S-bend circular cylinder generated on the Cray X-MP supercomputer show significant RCS reduction. Some of the limitations and possible extensions of this technique are discussed.

Ling, Hao↗