Search NASA⌕ Search

SEARCH · Search NASA

Results for “Operating Mode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Investigation of a cryogenic thermal diode

This paper describes a series of parametric investigations to determine the effect of various fluid charges on the performance of a 0.635-cm-diameter spiral-artery, liquid-trap diode in both the forward and reverse modes. Specific parameters such as forward- and reverse-mode conductances, shutdown times and energies, and recovery to forward-mode operation, are evaluated for ethane as a working fluid in the temperature range 170 K to 220 K. Results indicate that the heat pipe will not reliably start up in the forward mode. However, startup can be initiated when preceded by a diode reversal. Also concluded are data which show the susceptibility of the diode to fluid charge and tilt. The optimum fluid charge was found to be 2.67 g, and transport capability at this charge was in excess of 1200 W-cm at 200 K. The diode in the reverse mode exhibited a rapid shutdown (within 9 min) with a shutdown energy of 1150 J (0.32 Wh).

Williams, R. J.↗

Combustor Operability and Performance Verification for HIFiRE Flight 2

As part of the Hypersonic International Flight Research Experimentation (HIFiRE) Direct-Connect Rig (HDCR) test and analysis activity, three-dimensional computational fluid dynamics (CFD) simulations were performed using two Reynolds-Averaged Navier Stokes solvers. Measurements obtained from ground testing in the NASA Langley Arc-Heated Scramjet Test Facility (AHSTF) were used to specify inflow conditions for the simulations and combustor data from four representative tests were used as benchmarks. Test cases at simulated flight enthalpies of Mach 5.84, 6.5, 7.5, and 8.0 were analyzed. Modeling parameters (e.g., turbulent Schmidt number and compressibility treatment) were tuned such that the CFD results closely matched the experimental results. The tuned modeling parameters were used to establish a standard practice in HIFiRE combustor analysis. Combustor performance and operating mode were examined and were found to meet or exceed the objectives of the HIFiRE Flight 2 experiment. In addition, the calibrated CFD tools were then applied to make predictions of combustor operation and performance for the flight configuration and to aid in understanding the impacts of ground and flight uncertainties on combustor operation.

Storch, Andrea M.↗

Modal Identification Experiment accommodations review

The Modal Identification Experiment (MIE) will monitor the structure of the Space Station Freedom (SSF), and measure its response to a sequence of induced disturbances. The MIE will determine the frequency, damping, and shape of the important modes during the SSF assembly sequence including the Permanently Manned Configuration. This paper describes the accommodations for the proposed instrumentation, the data processing hardware, and the communications data rates. An overview of the MIE operational modes for measuring SSF acceleration forces with accelerometers is presented. The SSF instrumentation channel allocations and the Data Management System (DMS) services required for MIE are also discussed.

Klich, Phillip J.↗

Development of long wavelength semiconductor diode lasers near 28 microns for use in infrared heterodyne spectrometers

The development of tunable diode lasers operating in the 28 micrometers spectral region for use in infrared heterodyne spectrometers is reported. A process capable of yielding lasers emitting 500 micron W of multimode power, 112 micron W in a true single mode and true single mode operation at laser currents of up to 35% above threshold was developed. Results were obtained from narrow mesastripe (20 micrometer wide) short cavity (120 micrometer length) laser configurations. Six stripe geometry lasers, with a variety of cavity widths and lengths were delivered. The techniques to fabricate such devices was obtained and the long term reliability of such lasers by reproducible electrical and optical output characteristics fabrication from lasers are demonstrated.

Linden, K. J.↗

Preliminary Operational Results of the TDRSS Onboard Navigation System (TONS) for the Terra Mission

The Earth Observing System Terra spacecraft was launched on December 18, 1999, to provide data for the characterization of the terrestrial and oceanic surfaces, clouds, radiation, aerosols, and radiative balance. The Tracking and Data Relay Satellite System (TDRSS) Onboard Navigation System (ONS) (TONS) flying on Terra provides the spacecraft with an operational real-time navigation solution. TONS is a passive system that makes judicious use of Terra's communication and computer subsystems. An objective of the ONS developed by NASA's Goddard Space Flight Center (GSFC) Guidance, Navigation and Control Center is to provide autonomous navigation with minimal power, weight, and volume impact on the user spacecraft. TONS relies on extracting tracking measurements onboard from a TDRSS forward-link communication signal and processing these measurements in an onboard extended Kalman filter to estimate Terra's current state. Terra is the first NASA low Earth orbiting mission to fly autonomous navigation which produces accurate results. The science orbital accuracy requirements for Terra are 150 meters (m) (3sigma) per axis with a goal of 5m (1 sigma) RSS which TONS is expected to meet. The TONS solutions are telemetered in real-time to the mission scientists along with their science data for immediate processing. Once set in the operational mode, TONS eliminates the need for ground orbit determination and allows for a smooth flow from the spacecraft telemetry to planning products for the mission team. This paper will present the preliminary results of the operational TONS solution available from Terra.

Gramling, Cheryl↗

NASA Station Explorer for X-Ray Timing and Navigation Technology (SEXTANT) Mission Operations Architecture

"The Station Explorer for X-Ray Timing and Navigation (SEXTANT) mission is a technology demonstrationenhancement to the Neutron Star Interior Composition Explorer (NICER) mission, a NASA AstrophysicsExplorer Mission of Opportunity to the International Space Station (ISS) that was launched in June of 2017.The NICER instrument is a precision pointing X-ray telescope that provides measurements of neutron stars,which the SEXTANT mission uses to perform autonomous onboard X-ray Pulsar Navigation (XNAV) by usingmilli-second pulsars (MSPs), a category of neutron stars, as timing sources for navigation. By comparing thedetected time of arrival of X-ray photons to a reference of expected pulsar lightcurve timing models, one caninfer a range and range rate measurement based on light time delay. Since both timing and orientationinformation comes from a celestial source, this technology could provide a GPS-like navigation capabilityavailable throughout our Solar System and beyond. Applications that XNAV can support include outer planetand interstellar missions, manned missions, libration orbit missions, and current infrastructure such as the DeepSpace Network (DSN). The SEXTANT team successfully completed a rst demonstration of in-space andautonomous XNAV in November 2017. NICER and SEXTANT have separate teams, with NICER being theprimary team with its own science objectives. Operational modes for both missions must have concurrent andindependent components as well as an integrated ground system. Within this joint mission pro le, SEXTANToperations requires an infrastructure and cadence that is exible to handle concurrent science operations fromthe NICER team, independent autonomous navigation demonstrations, and events within the extensive ISSoperations environment. This paper rst details the infrastructure implemented and its concept of operations.It then describes the operations for the SEXTANT demonstration and lessons learned."

Yu, Wayne H.↗

Guidance, navigation, and control subsystem for the EOS-AM spacecraft

This paper presents the preliminary design of the Guidance, Navigation, and Control (GN&C) subsystem for the EOS-AM spacecraft and specifically focuses on the GN&C Normal Mode design. First, a brief description of the EOS-AM science mission, instruments, and system-level spacecraft design is provided. Next, an overview of the GN&C subsystem functional and performance requirements, hardware, and operating modes is presented. Then, the GN&C Normal Mode attitude determination, attitude control, and navigation systems are detailed. Finally, descriptions of the spacecraft's overall jitter performance and Safe Mode are provided.

Linder, David M.↗

Liquid Oxygen/Liquid Methane Integrated Propulsion System Test Bed

In support of NASA?s Propulsion and Cryogenic Advanced Development (PCAD) project, a liquid oxygen (LO2)/liquid methane (LCH4) Integrated Propulsion System Test Bed (IPSTB) was designed and advanced to the Critical Design Review (CDR) stage at the Johnson Space Center. The IPSTB?s primary objectives are to study LO2/LCH4 propulsion system steady state and transient performance, operational characteristics and to validate fluid and thermal models of a LO2/LCH4 propulsion system for use in future flight design work. Two phase thermal and dynamic fluid flow models of the IPSTB were built to predict the system performance characteristics under a variety of operating modes and to aid in the overall system design work. While at ambient temperature and simulated altitude conditions at the White Sands Test Facility, the IPSTB and its approximately 600 channels of system instrumentation would be operated to perform a variety of integrated main engine and reaction control engine hot fire tests. The pressure, temperature, and flow rate data collected during this testing would then be used to validate the analytical models of the IPSTB?s thermal and dynamic fluid flow performance. An overview of the IPSTB design and analytical model development will be presented.

Flynn, Howard↗

Thermodynamic Analysis of Dual-Mode Scramjet Engine Operation and Performance

Recent analytical advances in understanding the performance continuum (the thermodynamic spectrum) for air-breathing engines based on fundamental second-law considerations have clarified scramjet and ramjet operation, performance, and characteristics. Second-law based analysis is extended specifically in this work to clarify and describe the performance characteristics for dual-mode scramjet operation in the mid-speed range of flight Mach 4 to 7. This is done by a fundamental investigation of the complex but predictable interplay between heat release and irreversibilities in such an engine; results demonstrate the flow and performance character of the dual mode regime and of dual mode transition behavior. Both analytical and computational (multi-dimensional CFD) studies of sample dual-mode flow-fields are performed in order to demonstrate the second-law capability and performance and operability issues. The impact of the dual-mode regime is found to be characterized by decreasing overall irreversibility with increasing heat release, within the operability limits of the system.

Riggins, David↗

Biomedical ultrasonoscope

An instrument with a single ultrasonic transducer probe and a linear array of transducer probes permitting three operator modes is described. An 'A' and an 'M' mode scanner were combined with a 'C' mode scanner and a single receiver is used. The 'C' scanner mode enables two-dimensional cross sections of the viewed organ. Video-produced markers enable measurement of the dimensions of the heart. COS/MOS integrated logic circuit components are used to minimize power consumption and permit battery operation.

Lee, R. D.↗

Quiet Clean Short-haul Experimental Engine (QCSEE). Aerodynamic and aeromechanical performance of a 50.8 cm (20 inch) diameter 1.34 PR variable pitch fan with core flow

The fan aerodynamic and aeromechanical performance tests of the quiet clean short haul experimental engine under the wing fan and inlet with a simulated core flow are described. Overall forward mode fan performance is presented at each rotor pitch angle setting with conventional flow pressure ratio efficiency fan maps, distinguishing the performance characteristics of the fan bypass and fan core regions. Effects of off design bypass ratio, hybrid inlet geometry, and tip radial inlet distortion on fan performance are determined. The nonaxisymmetric bypass OGV and pylon configuration is assessed relative to both total pressure loss and induced circumferential flow distortion. Reverse mode performance, obtained by resetting the rotor blades through both the stall pitch and flat pitch directions, is discussed in terms of the conventional flow pressure ratio relationship and its implications upon achievable reverse thrust. Core performance in reverse mode operation is presented in terms of overall recovery levels and radial profiles existing at the simulated core inlet plane. Observations of the starting phenomena associated with the initiation of stable rotor flow during acceleration in the reverse mode are briefly discussed. Aeromechanical response characteristics of the fan blades are presented as a separate appendix, along with a description of the vehicle instrumentation and method of data reduction.

Giffin, R. G.↗

Assessment of the Impacts of ACLS on the ISS Life Support System using Dynamic Simulations in V-HAB

The Advanced Closed Loop System (ACLS) is currently under development by Airbus Defense and Space and is slated for launch to the International Space Station (ISS) in 2017. The addition of new hardware into an already complex system such as the ISS life support system (LSS) always poses operational risks. It is therefore important to understand the impacts ACLS will have on the existing systems to ensure smooth operations for the ISS. This analysis can be done by using dynamic computer simulations and one possible tool for such a simulation is Virtual Habitat (V-HAB). Based on Matlab (Registered Trademark) V-HAB has been under development at the Institute of Astronautics of the Technical University Munich (TUM) since 2006 and in the past has been successfully used to simulate the ISS life support systems. The existing V-HAB ISS simulation model treated the interior volume of the space station as one large ideally-stirred container. This model was improved to allow the calculation of the atmospheric composition inside the individual modules of the ISS by splitting it into ten distinct volumes. The virtual volumes are connected by a simulation of the inter-module ventilation flows. This allows for a combined simulation of the LSS hardware and the atmospheric composition aboard the ISS. A dynamic model of ACLS is added to the ISS simulation and different operating modes for both ACLS and the existing ISS life support systems are studied to determine the impacts of ACLS on the rest of the system. The results suggest that the US, Russian and ACLS CO2 systems can operate at the same time without impeding each other. Furthermore, based on the results of this analysis, the US and ACLS Sabatier systems can be operated in parallel as well to achieve the highest possible CO2 recycling together with a low CO2 concentration.

Puetz, Daniel↗

IUS/TUG Orbital Operations and Mission Support Study: Executive Summary - Volume 1

The space transportation system (STS) is discussed which will include a propulsive stage that is carried into low earth orbit by the space shuttle. Data were accumulated from the analyses of various stage concepts, operating modes, and projected missions (space tug systems studies, growth stage studies, engine studies, and critical area studies). The foundation formulated by these studies aided in establishing a tentative two-phase approach for the extension of the STS operating regime beyond the space shuttle including plane changes, higher orbits, geosynchronous orbits and beyond. The orbital operations study, was conducted to provide the generation and analysis of operational plans, requirement, and concepts for the utilization of these vehicles. Primary emphasis was placed on methods and techniques to provide a sound technical approach to operations at reduced cost for the STS mission period.

Source record↗

GOES-8 and -9 mission launch and operations support overview

The new series of geosynchronous operational environmental satellite (GOES) missions, GOES-8 and GOES-9, provide greater instrument coverage flexibility and greater resolution than previous GOES spinners. This added flexibility and the three-axis stabilized operating mode results in control system of increased complexity: almost 5000 real-time commands are sent daily to the satellites compared to 200 commands per day for GOES-7. These advanced technologies present new challenges to the NASA operations support personnel. In order to prepare for launching, post-launch tests and in-orbit operations, a mission planning scheme was developed in order to assure the flight system command and the systems' health monitoring. The mission operations approaches are reviewed together with the associated philosophies and the operation tools developed to assist the personnel in performing complex routine and special operation tasks.

McCuistion, D.↗

Assessment of the Impacts of ACLS on the ISS Life Support System Using Dynamic Simulations in V-HAB

The Advanced Closed Loop System (ACLS) is currently under development by Airbus Defense and Space and is slated for launch to the International Space Station (ISS) in 2017. The addition of new hardware into an already complex system such as the ISS life support system (LSS) always poses operational risks. It is therefore important to understand the impacts ACLS will have on the existing systems to ensure smooth operations for the ISS. This analysis can be done by using dynamic computer simulations and one possible tool for such a simulation is the Virtual Habitat (V-HAB). Based on MATLAB, V-HAB has been under development at the Institute of Astronautics of the Technical University of Munich (TUM) since 2004 and in the past has been successfully used to simulate the ISS life support systems. The existing V-HAB ISS simulation model treated the interior volume of the space station as one large, ideally-stirred container. This model was improved to allow the calculation of the atmospheric composition inside individual modules of the ISS by splitting it into twelve distinct volumes. The virtual volumes are connected by a simulation of the inter-module ventilation flows. This allows for a combined simulation of the LSS hardware and the atmospheric composition aboard the ISS. A dynamic model of ACLS is added to the ISS Simulation and several different operating modes for both ACLS and the existing ISS life support systems are studied and the impacts of ACLS on the rest of the system are determined. The results suggest that the US, Russian and ACLS CO2 systems can operate at the same time without impeding each other. Furthermore, based on the results of this analysis, the US and ACLS Sabatier systems can be operated in parallel as well to a achieve a very low CO2 concentration in the cabin atmosphere.

Putz, Daniel↗

Comparative vibration environments of transportation vehicles

Measured vibration data are presented for a number of air and surface vehicles. Consideration is given to the importance of direction effects; of vehicle operating modes such as takeoff, cruise, and landing; and of measurement location on the level and frequency of the measurements. Various physical measurement units or descriptors are used to quantify and compare the data. Results suggest the range of vibration associated with a particular mode of transportation and illustrate the comparative levels in terms of each of the descriptors. Collectively, the results form a data base which may be useful in assessing the ride of existing or future systems relative to vehicles in current operation. In addition, subjective response data obtained from vibration simulator studies are presented to illustrate human response characteristics as well as to indicate a laboratory approach for the development of ride-quality criteria.

Stephens, D. G.↗

In-Space Engine (ISE-100) Development - Design Verification Test

In the past decade, NASA has formulated science mission concepts with an anticipation of landing spacecraft on the lunar surface, meteoroids, and other planets. Advancing thruster technology for spacecraft propulsion systems has been considered for maximizing science payload. Starting in 2010, development of In-Space Engine (designated as ISE-100) has been carried out. ISE-100 thruster is designed based on heritage Missile Defense Agency (MDA) technology aimed for a lightweight and efficient system in terms volume and packaging. It runs with a hypergolic bi-propellant system: MON-25 (nitrogen tetroxide, N2O4, with 25% of nitric oxide, NO) and MMH (monomethylhydrazine, CH6N2) for NASA spacecraft applications. The utilization of this propellant system will provide a propulsion system capable of operating at wide range of temperatures, from 50 C (122 F) down to -30 C (-22 F) to drastically reduce heater power. The thruster is designed to deliver 100 lb(sub f) of thrust with the capability of a pulse mode operation for a wide range of mission duty cycles (MDCs). Two thrusters were fabricated. As part of the engine development, this test campaign is dedicated for the design verification of the thruster. This presentation will report the efforts of the design verification hot-fire test program of the ISE-100 thruster in collaboration between NASA Marshall Space Flight Center (MSFC) and Aerojet Rocketdyne (AR) test teams. The hot-fire tests were conducted at Advance Mobile Propulsion Test (AMPT) facility in Durango, Colorado, from May 13 to June 10, 2016. This presentation will also provide a summary of key points from the test results.

Trinh, Huu P.↗

New Flight Rules to Enable the Era of Aerial Mobility in the National Airspace System

In the 21st Century, new aviation markets, vehicle types, and technologies are fast emerging, inspiring new operational concepts for the National Airspace System such as Unmanned Aircraft Systems Traffic Management and Urban Air Mobility. These novel operations envision a dramatic increase in aerial mobility, or the ability to navigate freely through the airspace with unprecedented access and operational flexibility. Implementing these concepts presents a major challenge to the existing operational modes of Visual Flight Rules (VFR) and Instrument Flight Rules (IFR), developed under the limitations of early 20th Century technology and procedures to ensure safe navigation and separation from traffic. To meet this challenge and to support the needs of operators in the 21st Century and beyond, this paper proposes that VFR and IFR be augmented by new flight rules – Digital Flight Rules (DFR) – that leverage modern and emerging technologies and are not bound by restrictions borne of the state of technology 75-100 years ago. The objective of DFR is to provide safe and unfettered access to the airspace to all participating vehicle operators under all visibility conditions without incurring the limitations in operational flexibility inherent to IFR and even VFR. Advancements in communications, navigation, surveillance, aircraft connectivity, information access, automation technology, and supporting ground infrastructure provide the opportunity for the vehicle operator to engage at an unprecedented level in managing their flights regardless of flight visibility. Under DFR, these advancements enable the vehicle operator to assume full responsibility for traffic separation and therefore full trajectory management authority in all visibility conditions and airspace regions. The changes in roles and responsibilities are expected to enable greater airspace access and operational flexibility than afforded by IFR and VFR, thus enabling the emergence of new operations and a new era of advanced aerial mobility.

Mobility↗