Results for “PITCHING” — Page 16

DOE OSTI2024

Investigating the interactions between wakes and floating wind turbines using FAST.Farm

As floating offshore wind progresses to commercial maturity, wake and array effects across a farm of floating offshore wind turbines (FOWTs) will become increasingly important. While wakes of land-based and bottom-fixed offshore wind turbines have been extensively studied, only recently has this topic become relevant for floating turbines. This work presents an investigation of the mutual interaction between the motions of floating wind turbines and wakes using FAST.Farm. While FAST.Farm has been extensively validated across a wide range of conditions, it has never been validated for FOWT applications. Hence, in the first part of this work, we validate FAST.Farm by comparing simulations of a single FOWT against high-fidelity results from large-eddy simulations available in the literature. The validation is based on wake meandering, mean wake deflection, and velocity deficit at different downstream locations. This validation showed that the original axisymmetric (polar) wake model of FAST.Farm overpredicts the vertical wake deflection induced by shaft tilt and floater pitch, while the new curled wake model is capable of properly capturing the vertical wake deflection. In the second part, we use FAST.Farm to analyze a small three-unit array of FOWTs with a spacing of 7 diameters across a wide range of environmental conditions. The same National Renewable Energy Laboratory 5 MW reference wind turbine atop the OC4-DeepCwind semisubmersible is adopted for the three FOWTs and for the validation against high-fidelity simulations. To assess the effect of the floating substructure, we compare the power production, tower-base moments, and blade-root moments obtained for the floating turbines with the results obtained in a fixed-bottom configuration. The main differences introduced by the floating substructure are the motions induced by the waves, the change in the natural frequencies of the tower caused by differences in the boundary condition at its base, and the larger vertical deflection of the wake deficit due to the mean pitch of the platform. The impact of these differences, as well as other minor effects, are analyzed in detail.

16 TIDAL AND WAVE POWER↗

DOE OSTI2021

Collisional effects on resonant particles in quasilinear theory

A careful examination of the effects of collisions on resonant wave-particle interactions leads to an alternate interpretation and deeper understanding of the quasilinear operator originally formulated by Kennel and Engelmann (Phys. Fluids vol. 9, 1966, pp. 2377- 2388) for collisionless, magnetized plasmas, and widely used to model radio frequency heating and current drive. The resonant and nearly resonant particles are particularly sensitive to collisions that pitch angle scatter them out of and into resonance. As a result, the resonant particle-wave interactions occur in the center of a narrow collisional boundary when the collision frequency nu is very small compared to the wave frequency omega. The diffusive nature of the pitch angle scattering combined with the wave-particle resonance condition enhances the collision frequency by (omega/nu)2/3 >>1, resulting in an effective resonant particle collision time of tau_int ~ (nu /omega)2/3 nu <<1/ nu . A rigorous collisional boundary layer analysis generalizes the standard quasilinear operator to a form that is fully consistent with Kennel-Englemann, but allows replacing the delta function appearing in the diffusivity with a simple integral (having the appropriate delta function limit) retaining the new physics associated with the narrow boundary layer, while preserving the entropy production principle. The limitations of the collisional boundary layer treatment are also estimated, and indicate that substantial departures from Maxwellian are not permitted.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Investigation of Nonlinear Difference-Frequency Wave Excitation on a Semisubmersible Offshore-Wind Platform with Bichromatic-Wave CFD Simulations: Preprint

The natural surge and pitch frequencies of semisubmersible offshore wind platforms are typically designed to be below the wave frequencies to avoid direct excitation. However, surge or pitch resonance can be excited by the nonlinear low-frequency loads generated by irregular incident waves. Second-order potential-flow models with added Morison drag have been found to underpredict this low-frequency excitation and response. As part of the OC6 project, Computational Fluid Dynamics (CFD) simulations were performed to enable a better understanding of the low-frequency loads and the limitations of lower-fidelity models. The focus of the current paper is to set up a computationally cost-effective CFD simulation of a fixed semisubmersible platform to investigate nonlinear difference-frequency loads and establish the corresponding uncertainty in the results. Due to the high computing cost, CFD simulations of irregular waves can be challenging. Instead, simulations were performed with bichromatic waves having a shorter repeat period. A preliminary comparison with Quadratic Transfer Functions from second-order potential-flow theory shows that CFD models consistently predict higher nonlinear wave loads at the difference frequency, likely due to flow separation and viscous drag not accounted for in potential-flow theory.

2nd order↗

DOE OSTI2021

Open-Loop Control of Adjustable Tuned Mass Dampers for Floating Wind Turbine Platforms: Preprint

Floating offshore wind turbines have several advantages over their land-based counterparts, including access to stronger, more consistent winds and proximity to population centers. However, increased costs from the platform have been a challenge inhibiting their widespread adoption. New damping technologies with tunable target frequencies and damping ratios promise a greater degree of control over platform motions, allowing hulls to be designed smaller and reducing the overall cost of the turbines. In this work, a control strategy is proposed for these adjustable tuned mass dampers (TMDs). A frequency-domain model of the system is developed, from which response amplitude operators (RAOs) for the platform's rigid-body modes can be obtained for different natural frequencies and damping ratios of the dampers. Using these RAOs, and JONSWAP spectrums of operational and extreme sea states, the performance of the various damper settings are compared by evaluating the standard deviation of a rigid-body motion of interest (platform pitch or heave). By finding the optimal damper setting for a range of representative design load cases (DLCs), a lookup function is made to return the damper target frequency given the peak period of the sea state. To determine the current sea state, we propose a simple estimator that uses wave measurements (e.g., from a measurement buoy) to determine the peak period and significant wave height. The significant wave height is determined using the statistics of the past 100 seconds of wave elevation information and the peak period is computed using a frequency locked loop. Initial results show that we can use these estimated values to control the TMD natural frequency with an open loop controller. The controlled system is tested in a range of environmental conditions determined by the International Electrotechnical Commission design load cases (DLCs), which include normal and extreme wind and wave models. In these tests, we compare the performance of 4 cases: (1) no TMD, (2) a constant TMD based on the worst case DLC, (3) a controlled TMD based on known wind and wave environments, and (4) a real-time controlled TMD using estimated wind and wave environments. The effect of hull-based TMD control is also compared to changes in traditional wind turbine control via blade pitch.

control↗

DOE OSTI2021

Optimizing Power Generation of a Bottom-Raised Oscillating Surge Wave Energy Converter Using a Theoretical Model: Preprint

Preliminary sizing of an oscillating surge wave energy converter (OSWEC) is an iterative process that relies on knowledge of the relevant hydrodynamic coefficients for a given geometry. Often, the complex definition of the device geometry requires coefficients to be obtained through experiments or numerical boundary element solvers such as WAMIT. These techniques demand significant user and computational effort, therefore inhibiting the fine scale parametrization of object dimensions. In this study, a theoretical model, originally presented in Michele et al. (2016), is developed and demonstrated to efficiently optimize the power production for an OSWEC device (subjected to certain environmental conditions) with variations in device widths, heights, and distances from the seabed. Assuming negligible device thickness, the OSWEC motions are modelled as a bottom-raised two-dimensional flap in regular waves using potential flow theory formulated in elliptical coordinates. The solutions to this diffraction-radiation problem are obtained using Mathieu functions with appropriate boundary conditions. The resulting potentials are then used to derive frequency-dependent expressions for the added mass and radiation damping coefficients, along with wave excitation magnitude in surge, pitch, and coupled surge-pitch motions. Good agreement in hydrodynamic coefficient curves is shown between the theoretical model and the numerical results obtained from the boundary element-based program WAMIT. The theoretical model is then employed to maximize the time-averaged output power while maintaining or reducing the hinge reaction force, with variations in device dimensions, wave frequency and amplitude.

ACE↗

DOE OSTI2021

Optimizing Power Generation of a Bottomraised Oscillating Surge Wave Energy Converter Using a Theoretical Model

Preliminary sizing of an oscillating surge wave energy converter (OSWEC) is an iterative process that relies on knowledge of the relevant hydrodynamic coefficients for a given geometry. Often, the complex definition of the device geometry requires coefficients to be obtained through experiments or numerical boundary element solvers such as WAMIT. These techniques demand significant user and computational effort, therefore inhibiting the fine scale parametrization of object dimensions. In this study, a theoretical model, originally presented in Michele et al. (2016), is developed and demonstrated to efficiently optimize the power production for an OSWEC device (subjected to certain environmental conditions) with variations in device widths, heights, and distances from the seabed. Assuming negligible device thickness, the OSWEC motions are modelled as a bottom-raised two-dimensional flap in regular waves using potential flow theory formulated in elliptical coordinates. The solutions to this diffraction-radiation problem are obtained using Mathieu functions with appropriate boundary conditions. The resulting potentials are then used to derive frequency-dependent expressions for the added mass and radiation damping coefficients, along with wave excitation magnitude in surge, pitch, and coupled surge-pitch motions. Good agreement in hydrodynamic coefficient curves is shown between the theoretical model and the numerical results obtained from the boundary element-based program WAMIT. The theoretical model is then employed to maximize the time-averaged output power while maintaining or reducing the hinge reaction force, with variations in device dimensions, wave frequency and amplitude.

ACE↗

DOE OSTI2022

Integration and Packaging

Vertically integrated (3D) combinations of sensors and electronics provide the ability to fabricate small, fine pitch pixels with very small total capacitance monolithically integrated with complex circuitry. The small capacitance, enabled by the fine pixel pitch and low interconnect capacitance available in 3D hybrid bonding, provides excellent signal/noise with moderate power. This combination enables fabrication of integrated sensors and electronics with both excellent position and time resolution. In this white paper a discussion will be presented on 3D integration advantages, ongoing projects and prospects in high energy physics and beyond.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2023

Experiments to Measure the Effect of Tantalum on Critical Systems

Sandia National Laboratories (SNL) and Oak Ridge National Laboratory (ORNL) collaborated to develop a capability to test the epithermal/intermediate cross sections of materials at the SNL critical experiment facility using the Seven Percent Critical Experiment (7uPCX) fuel. As a result, a new set of critical experiments has been designed to target the epithermal cross sections of tantalum (Ta) and is scheduled to be performed at SNL in 2023. These critical experiments will be evaluated for inclusion in the 2024 edition of the International Criticality Safety Benchmark Evaluation Project (ICSBEP) Handbook. The focus of these critical experiments is to measure the effects of Ta on the critical array size. The critical array size will be determined by an approach-to-critical experiment with the number of fuel rods in the array as a free parameter. The core configurations are designed to optimize the reactivity worth of Ta and the overall percentage of Ta absorption rates in the epithermal/intermediate energy range (0.625 eV – 100 keV). The baseline core configuration includes 7uPCX fuel rods set at a triangular pitch of 1.016 cm and a central dry test region that utilizes a cadmium liner for filtering out thermal neutrons. The central test region has locations for 85 Ta rods set at a triangular pitch of 0.813 cm. The Ta reactivity worth for the case with 85 Ta rods is approximately 2.55%, with the percentage of Ta absorption rates within the intermediate energy range at nearly 90%.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2024

OpenFAST Modeling of the T-Omega Wind Floating Offshore Wind Turbine System

To reduce the cost of offshore wind energy through a more efficient design of the floating support structure, T-Omega Wind developed a novel lightweight and shallow-draft platform concept that aims to achieve a wave-following behavior without resonance amplification. The rotor and generator are carried by four tower legs with each leg supported by a shallow-draft float at the base. In preparation for a more detailed analysis, a coupled aero-hydro-elastic model of the proposed concept is developed in OpenFAST. The detailed modeling approach is presented, including a novel application of the SubDyn substructure dynamics module of OpenFAST to approximate the loads on the axle tube at the tower top from the rotor hub bearings. Preliminary results obtained with the OpenFAST model by rigidifying the substructure and blades indicate that the original sizing of the design can lead to large hub acceleration in the axial/surge and pitch directions due to platform-pitch motion. The high axial acceleration also potentially leads to large bending moments in the four tower legs. To address these issues, an updated design is developed with, among other changes, increased float spacing at the tower base and improved shear-transmitting geometry of the tower legs. The new design suggests significantly reduced extreme hub accelerations under the same conditions even with structural flexibility and will be further analyzed in the future through full aero-hydro-servo-elastic simulations.

ENGINEERING,WIND ENERGY↗

DOE OSTI2024

On-PIC Light Source Integration & Micro-dispensing of Solder Paste for Flip Chip Application

To reach the next level benefits of photonic integrated circuits (PICs), the Integrated Photonic Systems Roadmap-International describes the necessity of either heterogeneous or hybrid integration of light sources [1]. A new approach for hybrid integration is Photonic Wire Bonding where 3D nanolithography is used to pattern a polymer waveguide that connects light sources to PIC waveguides. The waveguides resemble electrical wire bonds and essentially do the same as their electrical counterpart for packaging photonic chips together. In order to reap the full benefits of a photonic wire bonds, the light source must be carefully packaged. In this work I seek to expand RIT’s photonic packaging capability by establishing a packaging process to integrate light sources, specifically an Indium Phosphide distributed feedback lasers and a reflective semiconductor optical amplifiers, directly onto a photonic integrated circuits. Another necessary requirement for PIC packaging is densely integrated electrical connectivity. In this thesis I developed a fine pitch flip chip interconnect technique demonstrated using gold stud bumps in conjunction with micro-dispensed solder paste. This work opens the door to high density photonic flip chip applications. The micro-dispensed solder paste dots having diameters 50-125 µm are currently being tested at a pitch of 150 µm . The gold stud bumps are formed with 1mil gold wire creating bumps with a diameter of 40-60 µm depending on specific parameter values. These capabilities will allow RIT to assemble and test novel photonic integrated devices, cutting down on the time and cost associated with third party assembly and tests facilities. Thereby keeping RIT at the forefront of photonic research.

Wongk, Nicole↗

DOE OSTI2025

Sensor Co-design for $\textit{smartpixels}$

Pixel tracking detectors at upcoming collider experiments will see unprecedented charged-particle densities. Real-time data reduction on the detector will enable higher granularity and faster readout, possibly enabling the use of the pixel detector in the first level of the trigger for a hadron collider. This data reduction can be accomplished with a neural network (NN) in the readout chip bonded with the sensor that recognizes and rejects tracks with low transverse momentum (p$_T$) based on the geometrical shape of the charge deposition (``cluster''). To design a viable detector for deployment at an experiment, the dependence of the NN as a function of the sensor geometry, external magnetic field, and irradiation must be understood. In this paper, we present first studies of the efficiency and data reduction for planar pixel sensors exploring these parameters. A smaller sensor pitch in the bending direction improves the p$_T$ discrimination, but a larger pitch can be partially compensated with detector depth. An external magnetic field parallel to the sensor plane induces Lorentz drift of the electron-hole pairs produced by the charged particle, broadening the cluster and improving the network performance. The absence of the external field diminishes the background rejection compared to the baseline by $\mathcal{O}$(10%). Any accumulated radiation damage also changes the cluster shape, reducing the signal efficiency compared to the baseline by $\sim$ 30 - 60%, but nearly all of the performance can be recovered through retraining of the network and updating the weights. Finally, the impact of noise was investigated, and retraining the network on noise-injected datasets was found to maintain performance within 6% of the baseline network trained and evaluated on noiseless data.

Shekar, Danush [Illinois U., Chicago]↗

DOE OSTI2021

Consortium for Production of Affordable Carbon Fibers in the United States (Final Report)

Various feedstocks from coal, petroleum and bio-based acrylonitrile were investigated for their ability to produce carbon fiber within DOE strength (250 ksi), modulus (25 Msi), elongation (>1%) and cost (≤$5/lb) goals for wider utilization in light-weight vehicles for the automotive industry. The overarching approach was to chemically identify and map the various feedstocks, understand the molecular transformation to produce carbon fiber precursors (mesophase for pitch materials of polyacrylonitrile polymer) and how these impact carbon fiber quality. Predictive models were built to relate the feedstocks and precursors to carbon fiber properties using atomistic and micro-scale modeling within ±15%. Using tow-level carbon fiber epoxy composites, carbon fibers tow-level predictions of elastic components of the carbon fibers were also successfully modeled within ±15%, using finite element analysis to confirm single filament carbon fiber properties. These models were validated with tow-level epoxy composite experiments from carbon fibers produced in this study.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2022

Failure analysis and design principles of silicon-based lithium-ion batteries using micron-sized porous silicon/carbon composite

Significant progresses have been made to overcome the fundamental challenges in silicon (Si)-based lithium-ion batteries (LIBs). However, much less work have been reported on the design and failure analysis these batteries for practical applications. In this work, we analyzed various cell design parameters affecting the performance of pouch cells using micron-sized porous Si with nano-pore structure and coated by pitch-carbon (p-Si/C). The correlation among particle level, electrode level, and cell level properties, especially the effect of electrode density on the volumetric capacity density of Si anode and full batteries have been systematically investigated. It is found that the corrosion of p-Si/C particle surface is the main failure mechanisms on the eventual capacity loss, while Li plating on anode electrode surface is the main reason for the fast capacity loss in later stage of cycling. The volumetric capacity of Si anode highly depends on both electrode density and the Si content. Moreover, the prelithiation of Si anodes is found to increase energy density while decreasing cycle life of Si-based full cells. Finally, the pathways and strategies for adoption of micron-sized p-Si/C anodes in LIBs have been proposed for their practical applications.

25 ENERGY STORAGE↗

DOE OSTI2020

Observation of High-Energy Electrons Precipitated by NWC Transmitter From PROBA-V Low-Earth Orbit Satellite

The very low-frequency transmitter in the Northwest Cape of Australia (NWC) has previously been observed to pitch-angle scatter electrons with energies from 30–400 keV, creating enhanced fluxes measured by low-Earth orbiting (LEO) satellites. Here we use observations from the Energetic Particle Telescope on PROBA-V. We compare the measured flux, as a function of local magnetic field strength, when the NWC transmitter is “on” versus “off,” and find enhanced fluxes only when NWC is “on” and located on the nightside. The enhanced fluxes occur in the population gradually transitioning from “permanently trapped” to “quasi-trapped.” We show that electrons up to 800 keV, substantially higher energy than previously studied, are scattered by resonant interactions with NWC to produce enhanced fluxes. The enhanced fluxes appear at multiple L-shells for each energy channel, consistent with resonance conditions at distinct wave normal angles, that indicate ducted interactions at L < 1.55 and unducted interactions at L > 1.65.

79 ASTRONOMY AND ASTROPHYSICS↗

DOE OSTI2022

Developing a Coal to Products Technology Portfolio

At Ramaco Carbon we are working to bring into existence a new carbon economy with the mottos “coal is too valuable to burn” and “no molecule left behind.” Our research focus is using coal (carbon ore) as a feedstock for a variety of high-value carbon products. We have developed a process and manufacturing technology portfolio including carbon fiber, porous carbons, nano-structured carbons (bulk graphene), building products, monolayer graphene, and rare earth elements (REEs). A review of these product lines, the associated processes, and economics will provide insight into the value of carbon ore as a feedstock for high-value and specialty products. We will present our current progress in manufacturing and tailoring the properties of porous carbons and nano-structured carbon to enhance existing products and produce novel products. Included is a discussion of the properties of carbon fiber derived from direct liquefaction of sub-bituminous coal, and from pitches produced by pyrolysis and solvation by supercritical CO2. New processes for converting carbon ore into structural building materials and monolayer graphene and the evaluation of REE deposits in a Powder River Basin thermal coal reserve will also be described. The presentation will provide a review of our carbon ore to products technology portfolio and the economic advantages of using carbon ore as a feedstock for advanced carbon products and several associated end use applications.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2022

Developing a Coal to Products Technology Portfolio

At Ramaco Carbon we are working to bring into existence a new carbon economy with the mottos “coal is too valuable to burn” and “no molecule left behind.” Our research focus is using coal (carbon ore) as a feedstock for a variety of high-value carbon products. We have developed a process and manufacturing technology portfolio including carbon fiber, porous carbons, nano-structured carbons (bulk graphene), building products, monolayer graphene, and rare earth elements (REEs). A review of these product lines, the associated processes, and economics will provide insight into the value of carbon ore as a feedstock for high-value and specialty products. We will present our current progress in manufacturing and tailoring the properties of porous carbons and nano-structured carbon to enhance existing products and produce novel products. Included is a discussion of the properties of carbon fiber derived from direct liquefaction of sub-bituminous coal, and from pitches produced by pyrolysis and solvation by supercritical CO2. New processes for converting carbon ore into structural building materials and monolayer graphene and the evaluation of REE deposits in a Powder River Basin thermal coal reserve will also be described. The presentation will provide a review of our carbon ore to products technology portfolio and the economic advantages of using carbon ore as a feedstock for advanced carbon products and several associated end use applications.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2026

202508 HAIIC IR Images with Attitude Data at BNF

This campaign aims to collect infrared imagery using a custom data acquisition system to improve and validate a previously developed attitude estimation algorithm, with a focus on ensuring reliable performance at higher altitudes. The system integrates a Boson+320 infrared camera, a VN-200 IMU for recording attitude data synchronized with image acquisition, and a Raspberry Pi 4B+ for onboard processing and storage. Image orientation was controlled using a Gremsy T7 gimbal. The primary dataset spans roll angles from −40° to 40° and pitch angles from −20° to 40°, sampled at 1° increments. Additional, smaller datasets were also collected at 2.5° angular intervals.

Boson+320↗

DOE OSTI2023

The DG03: An Outline of Suggested Changes

The Design Guideline 03 (DG03) published by the National Renewable Energy Laboratory in 2009 is widely used in the wind industry. It allows engineers to get acquainted with design aspects and methodologies to determine pitch and yaw bearing static capacity and fatigue life. The combination of the detailed theoretical descriptions and practical examples makes it a highly application-oriented document. Since its publication, the knowledge about oscillating bearings, slewing bearings, and wind turbines has grown significantly. Some aspects of the DG03 need updates to reflect the current state of the art. This work covers proposed changes for an upcoming revision of DG03.

design guideline↗