Search NASA⌕ Search

SEARCH · Search NASA

Results for “POWDER METALLURGY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Polymer Infused Composite Metal Foam as a Potential Aircraft Leading Edge Material

The leading edge of the aircraft wings must be free from three-dimensional disturbances caused by insect adhesion, ice accretion, and particle wear in order to improve flight performance, safety, and fuel efficiency of the aircraft. An innovative solution was explored in this work by infusing stainless steel composite metal foam (SS CMF) with a hydrophobic epoxy resin system. S-S CMF was made with 100% stainless steel using a powder metallurgy technique. The infused epoxy filled the macro- and microporosities, unique to SS CMF’s structure, creating a product with a density similar to that of aluminum. The contact angle, wear rate, erosion resistance, and insect adhesion of the novel infused composite metal foam were measured and compared to aluminum, epoxy and stainless steel. The infusion process was determined to fill up to 88% of the pores within the SS CMF and was found to reduce wettability and insect residue accretion. The contact angle of the infused SS CMF was 43% higher than its parent material, stainless steel, and 130% higher than aluminum. Insect residue maximum height and areal coverage were reduced by 60 and 30%, respectively, compared to aluminum. Grit blast experiments to simulate erosion resulted in a greater roughness increase for aluminum than for the parent epoxy resin or the resin-infused SS CMF. These results suggest that the durability and performance of infused SS CMF was superior compared to aluminum, which is the current leading edge material of choice. Based on the promising results under relevant wear and erosion conditions, it is concluded that the infused SS CMF can offer a potential tailored replacement to aluminum leading edge material.

Jacob C. Marx↗
NASA NTRS2021

Effect of Broaching Machining Parameters, Residual Stresses and Cold Work on Fatigue Life of Ni-based Turbine Disk P/M Alloy at 650°C

A study was performed to examine the effect of various broaching machining parameters on high temperature fatigue lives of a nickel-based Low Solvus High Refractory (LSHR) powder metallurgy disk alloy. The work was done to gain a better understanding of the effect of various broaching variables on the integrity and the durability of these fracture critical components. The influence of tool wear and broaching speed were examined in terms of their effect on residual stresses, cold work and surface roughness. These variables were shown to have a substantial effect on fatigue lives and the failure mode. The relationships between these parameters and fatigue crack initiation mechanisms are detailed. Statistical analyses evaluating these relationships are presented.

fatigue↗
NASA NTRSDate not supplied

Tribological performance of Al2O3-B2O3 composites: Role of CuOand CaO constituents

Al2O3-B2O3 based composites for wear resistant applications (e.g., seal rings and bearings) were manufactured using powder metallurgy route. Four different compositions were considered to control amount of in situ phases, mainly aluminum borate, formed during sintering. The fabricated composites were characterized using X-ray diffraction to identify the phases. Hardness was measured in terms of micro-hardness. The tribological performance of the composites were evaluated by conducting dry sliding tests against alumina balls at different humidity levels (10 – 95% relative humidity). The X-ray spectrum revealed that increase in B2O3 content in the composites increased the amount of aluminum borate phase that enhanced the micro-hardness. Results revealed that aluminum borate enhanced the wear resistance of the composites, whereas the humidity-sensitive alumina phase reduced friction at higher humidity levels. Furthermore, CuO and CaO (2-5 wt.%) were added separately to the composite, resulting in increased density by 22-48 %. Athough the addition of CuO and CaO led to increase in hardness and wear resistance of the composites, the coefficient of friction was negatively affected. The friction and wear performance along with wear mechanism are discussed with respect to observed phases in the composites.

Ashish K. Kasar↗
NASA NTRS2023

Influences of Varied Electrical Discharge Machining Operations on Surface Conditions of Several Nickel-Based Superalloys

Nickel-based superalloys designed for use in gas turbine engines blades are difficult and expensive to properly machine without undue surface damage, due in part to their superior mechanical properties at high temperatures. Numerically controlled electrical discharge machining (EDM) has progressed to commonly be used as a machining process for initial sectioning, detailed roughing, and even some finishing operations. The objective of this study was to examine the effect of EDM on resulting surface conditions of superalloy 718 after slicing using typical rough, semi-finish, and finish condition sets with a typical wire EDM machine. Surface roughness, residual stress, and microstructures were compared for these conditions. The varied EDM conditions influenced surface roughness as intended. The residual stresses and surface roughness directly corresponding to the EDM steps were determined. While roughness decreased when progressing from rough to finish EDM conditions, tensile residual stresses unexpectedly increased. Brief assessments after EDM of two higher performance powder metallurgy disk superalloys ME209 and LSHR indicated this inverse relationship of roughness versus tensile residual stress was also present for these superalloys, where tensile residual stresses were significantly enhanced.

superalloys↗
NASA NTRS2023

Competition of Failure Modes in an Additively Manufactured Disk Superalloy

Additive manufacturing of powder metallurgy (PM) disk superalloys can produce unique microstructures that differ from those usually encountered in traditional processing as the result of consolidation, forging, and heat treatments. Unusual variations in grain size, major and minor phase precipitate sizes, and defects can occur. The failure modes associated with these unique microstructures are of high interest. The objective of this study was to compare the failure modes for a low solvus, high refractory (LSHR) PM disk superalloy produced by electron-beam-melting additive manufacturing. Specimens were subsequently given different solution heat treatments and a fixed aging heat treatment. Tensile, creep, and fatigue failure modes were screened in tests at elevated temperatures. Failure modes were considered with respect to these unique microstructures.

additive manufacturing↗
NASA NTRS1993

Dimensional Stability of High Purity Invar 36

High performance requirements for the Imaging Science Subsystem (ISS)/Narrow Angle Camera (NAC) instrument on the NASA/Jet Propulsion Laboratory (JPL) Cassini spacecraft impose very stringent demands for dimensional stability of metering rods in the camera's athermalizing system.

imaging↗
NASA NTRS1986

Aqueous sodium chloride induced intergranular corrosion of Al-Li-Cu alloys

Two methods have been explored to assess the susceptibility of Al-Li-Cu alloys to intergranular corrosion in aqueous sodium chloride solution. They are: (1) constant extension rate testing with and without alternate-immersion preexposure and (2) metallographic examination after exposure to a NaCl-H2O2 corrosive solution per Mil-H-6088F. Intergranular corrosion was found to occur in both powder and ingot metallurgy alloys of similar composition, using both methods. Underaging rendered the alloys most susceptible. The results correlate to stress-corrosion data generated in conventional time-to-failure and crack growth-rate tests. Alternate-immersion preexposure may be a reliable means to assess stress corrosion susceptibility of Al-Li-Cu alloys.

Pizzo, P. P.↗