Starting criterion for hypersonic inlets
Starting criterion for hypersonic inlets with large turbulent boundary layers, considering total pressure recovery from all shock and viscous losses
Goldberg, T. J.↗
SEARCH · Search NASA
Results for “PRESSURE RECOVERY”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Interference Effects of Fuselage-Stored Missiles on Inlet Duct Model of an Interceptor-Type Aircraft at Mach Numbers 1.5 to 1.9
The effect of missile armament on the performance of an interceptor-type aircraft model has been determined at Mach numbers 1.5, 1.7, and 1.9 and at angles of attack to 19 deg. With this configuration missiles were carried in a bay located on the bottom of the aircraft fuselage and mounted to a rotatable missile door. Rotation of the door then brought the missiles into the external or firing position. The aircraft model was characterized by triangular-shaped normal-shock inlets located at the wing roots. Relatively short and curved subsonic diffusers fed simulated twin side-by-side turbojet engines. Inasmuch as the missile bay extended considerably ahead of the inlet station, rotation of the missile door created considerable disturbance of the flow entering the inlets. In comparison with the internal missile arrangement, the external missile configurations increased the model lift, drag, and pitching moment. While the diffuser-exit flow distortion and static-pressure fluctuations were not greatly affected, diffuser total-pressure recovery was reduced as much as 0.058 at Mach number 1.9 for one missile configuration. The most detrimental effect of missile-door rotation occurred at the transient door positions, or with the door halfwzy between the missiles-in and -out conditions. At this door position the flow into the inlets was highly asymmetrical. Although the performance of both left and right ducts was generally reduced, the inlet duct on the cavity side of the missile door was most severely penalized, becoming unstable recovery losses and increases in flow distortion. The installation of fuselage fences along the missile bay was only partially effective in reducing these losses.
Piercy, T. G.↗
Investigation of a mixed compression axisymmetric inlet at Mach number 5.3
The hypersonic diffuser portion of an uncooled high performance mixed compression, axisymmetric inlet suitable for subsonic burning engines was designed and tested. Performance of a model with a 25.4-cm capture diameter was measured in a wind tunnel and the results were compared with theoretical predictions calculated by a comprehensive computer program. All tests were conducted at a Mach number of 5.3 at a total temperature of 667 K and a total pressure of 11.57 atm. The angle of attack ranged from 0 to + or - 3 deg. Performance at angle of attack remained high. Reasonably high performance in the throat (maximum throat pitot-pressure recovery of 77 percent and an average value of 58 percent) was obtained at 0 deg angle of attack with relatively large amounts of boundary-layer bleed (11 to 22 percent of the capture mass flow). The computer program used in the design of this inlet is considered marginally adequate for predicting hypersonic inlet flow fields. Although the program as it now exists is very useful, an improved computer program that more accurately predicts the boundary layer and the shock-wave-boundary-layer interaction and accounts for boundary-layer bleed should be developed for reliability predicting hypersonic inlet flow fields.
Latham, E. A.↗
Transonic and supersonic test of a Mach 2.65 mixed-compression axisymmetric intake
The test results describe isolated intake performance between Mach 0.95 and the cruise Mach number of 2.65 at angles of incidence from +5 to -5 deg. Maximum total pressure recoveries of over 94 percent with 10 percent distortion were recorded at the compressor face in the Mach range from 2.65 to 2.4. Typical cruise operating recovery was 91 percent with 13 percent distortion, 7 percent bleed, 5 percent corrected flow stability margin, and 2.2 deg angle-of-incidence tolerance without need for control action. In the started range below Mach 2.4, recoveries were 2 percent to 4 percent lower than the recoveries above Mach 2.4, and the distortion increased to approximately 20 percent. At Mach 0.95 the maximum measured capture flow was 99.4 percent of the theoretical choked value. The recovery was 97.1 percent with less than 10 percent distortion.
Koncsek, J. L.↗
Steady-state and dynamic pressure phenomena in the propulsion system of an F-111A airplane
Flight tests were conducted with two F-111A airplanes to study the effects of steady-state and dynamic pressure phenomena on the propulsion system. Analysis of over 100 engine compressor stalls revealed that the stalls were caused by high levels of instantaneous distortion. In 73 percent of these stalls, the instantaneous circumferential distortion parameter, k sub theta, exhibited a peak just prior to stall higher than any previous peak. The K sub theta parameter was a better indicator of stall than the distortion factor, k sub d, and the maximum-minus-minimum distortion parameter, d, was poor indicator of stall. Inlet duct resonance occurred in both F-111A airplanes and is believed to have been caused by oscillations of the normal shock wave from an internal to an external position. The inlet performance of the two airplanes was similar in terms of pressure recovery, distortion, and turbulence, and there was good agreement between flight and wind-tunnel data up to a Mach number of approximately 1.8.
Burcham, F. W.↗
High tip speed fan inlet noise reduction using treated inlet splitters and accelerating inlets (quiet engine program fan C scale model)
A series of inlet suppression tests were run on a supersonic tip speed fan which employed an acoustically treated cowl wall, treated splitters and elevated average throat Mach numbers in various combinations. Results show appreciable fan noise reductions at high fan speeds; 15-18 PNdB. On the basis of inlet total pressure recovery loss per PNdb of noise reduction, an inlet with no splitters produced the most efficient design. However, greater reduction in noise was achieved with one splitter in the inlet. It was also noted that moderate increases in inlet Mach number increased noise in the acoustically treated inlets and that Mach numbers in excess of 0.65 were required before net noise reduction was realized.
Kazin, S. B.↗
Hypersonic flows in large-scale inlet models.
Analytical and experimental investigations were conducted to determine the characteristics of the internal flows in model passages representative of inlets for a typical Mach 12 hypersonic cruise vehicle and also sufficiently large for reliable data to be obtained. Three large-scale inlet models, each having a different internal compression ratio, were designed to provide maximum performance at the throat stations. Tests were conducted in the Mach 7.4 nozzle of the NASA Ames 3.5-foot hypersonic wind tunnel at a nominal test Reynolds number of 2,700,000 per ft. The experimental results revealed that a high level of total pressure recovery, approximately 0.85 (relative to the inlet-entrance conditions) for the core flow of the internal passage, was achieved for each inlet design.
Seebaugh, W. R.↗
Some design considerations for supersonic cruise mixed compression inlets
A mixed compression inlet designed for supersonic cruise has very demanding requirements for high total pressure recovery and low bleed and cowl drag. However, since the optimum inlet for supersonic cruise performance may have other undesirable characteristics, it is necessary to establish trade-offs between inlet performance and other inlet characteristics. Some of these trade-offs between the amount of internal compression, aerodynamic performance and angle-of-attack tolerance are reviewed. Techniques for analysis of boundary layer control and subsonic diffuser flow are discussed.
Bowditch, D. N.↗
Minimizing boundary layer bleed for a mixed compression inlet
An experimental investigation of a full scale mixed compression inlet sized for the TF30-P-3 turbofan engine was conducted at Mach 2.5 and 2.0 operating conditions. The two cone axisymmetric inlet had minimum internal contraction consistent with high total pressure recovery and low cowl drag. At Mach 2.5, inlet recovery exceeded 0.90 with only 0.02 centerbody bleed mass-flow ratio and zero cowl bleed. A centerbody bleed of approximately 0.05 gave a maximum inlet unstart angle-of-attack of 6.85 deg. Inlet performance and angle-of-attack tolerance is presented for operation at Mach 2.5 and 2.0.
Wasserbauer, J. F.↗
Possibilities for improved supersonic inlet performance
The results from detailed large-scale inlet tests were examined to assess the penalties, in terms of vehicle cruise range, for boundary-layer bleed, less than ideal engine-face pressure recovery, inlet weight, and external cowl drag. The assessment suggested specific improvements in the design of the inlet system that may increase the range of a typical supersonic transport approximately 6.9%. While no single design improvement can account for a large increase in range, careful attention to each design detail can yield a substantial total improvement. Because of noise considerations, future engines for advanced supersonic transports may be approximately 50% larger than used for the present study, making the effects of improved inlet performance even more important.
Sorensen, N. E.↗
Some design considerations for supersonic cruise mixed compression inlets
A mixed compression inlet designed for supersonic cruise has very demanding requirements for high total pressure recovery and low bleed and cowl drag. However, since the optimum inlet for supersonic cruise performance may have other undesirable characteristics, it is necessary to establish trade-offs between inlet performance and other inlet characteristics. The paper will review some of these trade-offs between the amount of internal compression, aerodynamic performance and angle-of-attack tolerance. Also some techniques in use at the Lewis Research Center for analysis of boundary layer control and subsonic diffuser flow will be discussed.
Bowditch, D. N.↗
Minimizing boundary layer bleed for a mixed compression inlet
An experimental investigation of a full scale mixed compression inlet sized for the TF30-P-3 turbofan engine was conducted at Mach 2.5 and 2.0 operating conditions. The two cone axisymmetric inlet had minimum internal contraction consistent with high total pressure recovery and low cowl drag. At Mach 2.5, inlet recovery exceeded 0.90 with only 0.02 centerbody bleed mass-flow ratio and zero cowl bleed. A centerbody bleed of approximately 0.05 gave a maximum inlet unstart angle-of-attack of 6.85 deg. Inlet performance and angle-of-attack tolerance is presented for operation at Mach 2.5 and 2.0.
Wasserbauer, J. F.↗
An inlet analysis for the NASA hypersonic research engine aerothermodynamic integration model
A theoretical analysis for the inlet of the NASA Hypersonic Research Engine (HRE) Aerothermodynamic Integration Model (AIM) has been undertaken by use of a method-of-characteristics computer program. The purpose of the analysis was to obtain pretest information on the full-scale HRE inlet in support of the experimental AIM program (completed May 1974). Mass-flow-ratio and additive-drag-coefficient schedules were obtained that well defined the range effected in the AIM tests. Mass-weighted average inlet total-pressure recovery, kinetic energy efficiency, and throat Mach numbers were obtained.
Andrews, E. H., Jr.↗
Aeroacoustic performance of scale model sonic inlets
A low speed wind tunnel was used to evaluate the inflight aeroacoustic performance of several single- and multiple-passage sonic inlets. Takeoff and approach geometries were tested, and the effects of inlet lip and diffuser design were determined. Results indicate that the single passage geometries, in particular a cylindrical centerbody takeoff geometry and a bulb shaped centerbody approach geometry, provide the highest level of aeroacoustic performance. Increasing inlet lip contraction ratio extends the maximum incidence angle for attached lip flow, while increasing inlet diffuser length results in higher total pressure recovery for a given amount of noise suppression.
Abbott, J. M.↗
Design of a very-low-bleed Mach 2.5 mixed-compression inlet with 45 percent internal contraction
A full-scale, mixed-compression inlet was designed for operation with the TF30-P-3 turbofan engine and tested at Mach numbers of 2.5 and 2.0. The two-cone axisymmetric inlet had minimum internal contraction consistent with high total pressure recovery and low cowl drag. At Mach 2.5, inlet recovery was 0.906 with only 0.021 centerbody bleed mass-flow ratio and no cowl bleed. Increased centerbody bleed gave a maximum inlet unstart angle of attack of 6.85 deg. At Mach 2.0, inlet recovery was 0.94 with only 0.014 centerbody bleed mass-flow ratio and no cowl bleed. Inlet performance and angle-of-attack tolerance is presented for operation at Mach numbers of 2.5 and 2.0.
Wasserbauer, J. F.↗
Effect of wall edge suction on the performance of a short annular dump diffuser with exit passage flow resistance
The effect of wall edge suction on the performance of a short annular dump diffuser having a perforated plate flow resistance device in the exit passage was evaluated. Testing was conducted with air at near ambient pressure and temperature at inlet Mach numbers of 0.18 and 0.27 with suction rates up to 13.5 percent. Results show that pressure recovery downstream of the perforated plate was improved significantly by suction. Optimum performance was obtained with the flow resistance plate located at one inlet passage height downstream of the dump plane.
Juhasz, A. J.↗
Aeroacoustic performance of scale model sonic inlets
Various means can be used to vary engine inlet throat areas in order to reduce noise generated at takeoff and approach. Low-speed wind-tunnel tests were performed to evaluate the aeroacoustic performance of two takeoff geometries (cylindrical centerbody and bulb-shaped centerbody) and four approach geometries (bulb-shaped centerbody, annular ring, radial vanes, and step diffuser). The effects of inlet internal lip shape and diffuser length on sonic inlet performance were also investigated. It was found that the single-passage geometries, in particular a cylindrical centerbody takeoff geometry and a bulb-shaped centerbody approach geometry, provide the highest level of aeroacoustic performance. Increasing the inlet lip contraction ratio extends the maximum incidence angle for attached lip flow, while increasing the inlet diffuser length increases total pressure recovery for a given amount of noise suppression.
Abbott, J. M.↗
Design and testing of new center inlet and S-duct for B-727 airplane with refanned JT8D engines
The work described in this paper was part of the NASA refan program. The airflow requirement of the refanned JT8D (-100 series) engine increased about 50% above that of the basic JT8D. This required a redesign of the center inlet and S-duct of the Boeing 727 airplane. The paper describes the design constraints for the S-duct and the analytic method used to define the lines of the new duct. Model tests that were conducted at static, angle-of-attack, and crosswind conditions are described with a variety of flow control devices. Test results showed that the new inlet and S-duct have a pressure recovery comparable to that of the existing inlet. By employing corotating vortex generators, less flow distortion was obtained for the core region than the existing duct has with its counter rotating vortex generators.
Ting, C. T.↗