Search NASA⌕ Search

SEARCH · Search NASA

Results for “Process variable”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Adhesion-force micro-scale study of desiccating granular material

Experiments on five-, four-, three- and two-wet-hydrophilic-grain clusters were performed to investigate evolution of adhesion of granular media during drying on the micro-scale. The experiments show that the adhesion-force of a cluster initially grows at most to three times the original value before decreasing to zero by the end of evaporation. The adhesion-force is composed of capillary pressure force acting over the liquid/solid contact surface area, and surface tension forces acting over the three-phase contact perimeter length. This is in contrast with most macro-scale phenomenological models, in which the only desaturation process variables affecting strength are suction and saturation. Both the contact surface area and contact perimeter length are reduced to zero upon complete liquid evaporation. The morphology of an evaporating water body evolves through slow flow controlled by evaporation rate, interrupted by various modes of fast air entry, which are non-equilibrium jumps of liquid/gas interfaces (Haines jumps). The instabilities involve large adhesion force discontinuities and substantial water mass reconfiguration with water flow in an extremely short time, which makes the process transient. The reconfigurations can reduce the original multi-grain water clusters to four-, three- and two-grain clusters by way of three different instability modes: of thin-sheet instability, or meniscus snap-through instability, depending on the sign of the Gauss curvature of the liquid surface, or finally, for two-grain bridges only, a liquid wire pinch-off. For larger meso-scale assemblies, however, the global adhesion-force evolution is little affected by the jumps. The air entries are potential sites for drying cracks. The (approximately) calculated capillary pressure for two- and three-grain clusters, in no cases is seen to reach high values, predicted from water retention curves.

Engineering↗

Predicting Initial Trans-Membrane Pressure for Optimized Operations in UF Unit Using Random Forest

With the growing scarcity of freshwater, innovative process design mechanisms like Reverse Osmosis (RO) are increasingly gaining attention among water treatment utilities to address the rising demand. Ensuring reliable water production necessitates efficient resource utilization, minimizing downtime in (ultra-filtration) UF systems. Recent advancements in machine learning (ML) have enabled the development of accurate data-driven models for Model Predictive Control (MPC), often requiring minimal prior knowledge of underlying physical processes. In this study, we present predictive regression models based on Random Forest (RF) and Auto-Regressive (AR) approaches to forecast the initial Trans-Membrane Pressure (TMP) for each filtration cycle in data generated by Direct Potable Reuse (DPR) systems. The proposed RF-based model demonstrates superior performance compared to baseline methods, including historical mean, Last Observation Carried Forward (LOCF), and naïve AR models, across various forecasting horizons in terms of root mean square error (RMSE) metric. To evaluate how different classes of process variables contribute to TMP dynamics over time, we examine the feature importance of independent covariates across multiple forecast horizons. This analysis provides insight into the temporal relevance of operational and sensor-derived features, guiding control and monitoring strategies. Additionally, the impact of hyperparameter tuning on TMP prediction performance is studied for both direct and recursive RF modelling approaches across increasing forecast horizons. Accurate prediction of initial TMP is critical for optimizing RO operations, as it enables the development of robust modelling frameworks by accurately estimating membrane fouling trends, thereby enhancing process efficiency and long-term reliability. The demonstrated efficacy of the RF-based approach highlights its potential as a tool for real-time decision-making in water treatment systems, paving the way for advanced process optimization and sustainable water resource management.

Mukherjee, Subrata [ORNL] (ORCID:0000000309930338)↗

YIELD STRENGTH PREDICTION FOR RAPID AGE-HARDENING HEAT TREATMENT OF ALUMINUM ALLOYS

A constitutive model has been developed to predict the yield strength aging curves for aluminum casting alloys during non-isothermal age-hardening processes. The model provides the specific relationship between the process variables and yield strength. Several aging heat treatment scenarios have been investigated using the proposed model, including two-step aging recipes. Two-step aging heat treatments involve a low temperature regime to promote nucleation of secondary phases and a second step at higher temperature for the growth of the secondary phases. The predicted results show that yield strength of approximately 300MPa might be obtained in shorter aging time, of approximately 30 minutes. Thus, better mechanical properties can be obtained by optimizing the time-temperature schedules for the precipitation hardening process of heat treatable aluminum alloys.

Yin, Hebi↗

Detailed Microstructural Characterization of the Disk Alloy ME3

The advanced powder metallurgy disk alloy ME3 was designed using statistical screening and optimization of composition and processing variables in the NASA/General Electric/Pratt & Whitney HSR/EPM disk program to have extended durability for large disks at maximum temperatures of 600 to 700 C. Scaled-up disks of this alloy were then produced at the conclusion of that program to demonstrate these properties in realistic disk shapes. The objective of the present study was to assess the microstructural characteristics of these ME3 disks at two consistent locations, in order to enable estimation of the variations in microstructure across each disk and across several disks of this advanced alloy. Scaled-up disks processed in the HSR/EPM Compressor/Turbine Disk program had been sectioned, machined into specimens, and tested in tensile, creep, fatigue, and fatigue crack growth tests by NASA Glenn Research Center, in cooperation with General Electric Engine Company and Pratt & Whitney Aircraft Engines. For this study, microstructures of grip sections from tensile specimens in the bore and rim were evaluated from these disks. The major and minor phases were identified and quantified using transmission electron microscopy (TEM). Particular attention was directed to the .' precipitates, which along with grain size can predominantly control the mechanical properties of superalloy disks.

Gabb, Timothy P.↗

The Influence of Residual Copper Catalyst on the Polymer-to-Ceramic Conversion of a Click-Derived Polycarbosilane

Preceramic polymers (PCPs) are a key class of materials for the preparation of advanced ceramic components. Following conventional polymer processing and subsequent pyrolysis, polymer-derived ceramic (PDC) fibers, monoliths, and composites offer novel engineering opportunities for aerospace applications. Despite the rapidly emerging commercial applications of PDCs, many basic scientific questions remain regarding the structural transformation of the polymer to the final ceramic and how processing variables affect PDC materials properties. PCPs prepared using a mild and scalable copper (Cu) catalyzed azide/alkyne “click” reaction have been demonstrated as a unique class of material that can bind with transition metals, ultimately producing ultrahigh temperature ceramics (UHTCs) upon pyrolysis. Unexpectedly, it was found that the removal of residual Cu catalyst from a model click-derived polycarbosilane PCP significantly reduced the ceramic yield during pyrolysis. Herein, we report the influence of Cu impurities on polycarbosilane-derived SiC ceramics and present a mechanistic understanding of the unintended role of Cu in the polymer-to-ceramic conversion process. Synchrotron-based scattering and spectroscopy methods were implemented to track the evolution of different atomic species and local structures as well as the influence of Cu toward atomic-scale structures in the final ceramics. It was determined that Cu impurities catalyze the formation of silicon carbide through the formation of an intermediate molten copper/copper silicide, ultimately increasing the ceramic yield. Overall, this contribution highlights the need to carefully assess the interplay between the chemistries needed for PCP synthesis and their potential influence on final PDCs following processing.

Ponder, Jr., James F. [Air Force Research Laborato↗

Metallurgical Mechanisms Controlling Mechanical Properties of Aluminum Alloy 2219 Produced By Electron Beam Freeform Fabrication

The electron beam freeform fabrication (EBF3) layer-additive manufacturing process has been developed to directly fabricate complex geometry components. EBF3 introduces metal wire into a molten pool created on the surface of a substrate by a focused electron beam. Part geometry is achieved by translating the substrate with respect to the beam to build the part one layer at a time. Tensile properties have been demonstrated for electron beam deposited aluminum and titanium alloys that are comparable to wrought products, although the microstructures of the deposits exhibit features more typical of cast material. Understanding the metallurgical mechanisms controlling mechanical properties is essential to maximizing application of the EBF3 process. In the current study, mechanical properties and resulting microstructures were examined for aluminum alloy 2219 fabricated over a range of EBF3 process variables. Material performance was evaluated based on tensile properties and results were compared with properties of Al 2219 wrought products. Unique microstructures were observed within the deposited layers and at interlayer boundaries, which varied within the deposit height due to microstructural evolution associated with the complex thermal history experienced during subsequent layer deposition. Microstructures exhibited irregularly shaped grains, typically with interior dendritic structures, which were described based on overall grain size, morphology, distribution, and dendrite spacing, and were correlated with deposition parameters. Fracture features were compared with microstructural elements to define fracture paths and aid in definition of basic processing-microstructure-property correlations.

Domack, Marcia S.↗

A new hybrid genetic algorithm for optimizing the single and multivariate objective functions

In this work a new hybrid genetic algorithm was developed which combines a rudimentary adaptive steepest ascent hill climbing algorithm with a sophisticated evolutionary algorithm in order to optimize complex multivariate design problems. By combining a highly stochastic algorithm (evolutionary) with a simple deterministic optimization algorithm (adaptive steepest ascent) computational resources are conserved and the solution converges rapidly when compared to either algorithm alone. In genetic algorithms natural selection is mimicked by random events such as breeding and mutation. In the adaptive steepest ascent algorithm each variable is perturbed by a small amount and the variable that caused the most improvement is incremented by a small step. If the direction of most benefit is exactly opposite of the previous direction with the most benefit then the step size is reduced by a factor of 2, thus the step size adapts to the terrain. A graphical user interface was created in MATLAB to provide an interface between the hybrid genetic algorithm and the user. Additional features such as bounding the solution space and weighting the objective functions individually are also built into the interface. The algorithm developed was tested to optimize the functions developed for a wood pelleting process. Using process variables (such as feedstock moisture content, die speed, and preheating temperature) pellet properties were appropriately optimized. Specifically, variables were found which maximized unit density, bulk density, tapped density, and durability while minimizing pellet moisture content and specific energy consumption. The time and computational resources required for the optimization were dramatically decreased using the hybrid genetic algorithm when compared to MATLAB's native evolutionary optimization tool.

feedstock↗

Unit cell geometry of multiaxial preforms for structural composites

The objective of this study is to investigate the yarn geometry of multiaxial preforms. The importance of multiaxial preforms for structural composites is well recognized by the industry but, to exploit their full potential, engineering design rules must be established. This study is a step in that direction. In this work the preform geometry for knitted and braided preforms was studied by making a range of well designed samples and studying them by photo microscopy. The structural geometry of the preforms is related to the processing parameters. Based on solid modeling and B-spline methodology a software package is developed. This computer code enables real time structural representations of complex fiber architecture based on the rule of preform manufacturing. The code has the capability of zooming and section plotting. These capabilities provide a powerful means to study the effect of processing variables on the preform geometry. the code also can be extended to an auto mesh generator for downstream structural analysis using finite element method. This report is organized into six sections. In the first section the scope and background of this work is elaborated. In section two the unit cell geometries of braided and multi-axial warp knitted preforms is discussed. The theoretical frame work of yarn path modeling and solid modeling is presented in section three. The thin section microscopy carried out to observe the structural geometry of the preforms is the subject in section four. The structural geometry is related to the processing parameters in section five. Section six documents the implementation of the modeling techniques into the computer code MP-CAD. A user manual for the software is also presented here. The source codes and published papers are listed in the Appendices.

Ko, Frank↗

Bench Scale Process for Low Cost CO 2 Capture Using a Phase-Changing Absorbent: Final Scientific/Technical Report

The objective of this project is to design and build a bench-scale process for a novel phase-changing aminosilicone-based CO 2 -capture solvent. The project will establish scalability and technical and economic feasibility of using a phase-changing CO 2 -capture absorbent for post-combustion capture of CO 2 from coal-fired power plants. The U.S. Department of Energy’s goal for Transformational Carbon Capture Technologies is the development of technologies available for demonstration by 2025 that can capture 90% of emitted CO 2 with at least 95% CO 2 purity for less than $40/tonne of CO 2 captured. In the first budget period of the project, the bench-scale phase-changing CO2 capture process was designed using data and operating experience generated under a previous project (ARPA-e project DE-AR0000084). Sizing and specification of all major unit operations was completed, including detailed process and instrumentation diagrams. The system was designed to operate over a wide range of operating conditions to allow for exploration of the effect of process variables on CO 2 capture performance. In the second budget period of the project, individual bench-scale unit operations were tested to determine the performance of each of each unit. Solids production was demonstrated in dry simulated flue gas across a wide range of absorber operating conditions, with single stage CO 2 conversion rates up to 75mol%. Desorber operation was demonstrated in batch mode, resulting in desorption performance consistent with the equilibrium isotherms for GAP-0/CO 2 reaction. Important risks associated with gas humidity impact on solids consistency and desorber temperature impact on thermal degradation were explored, and adjustments to the bench-scale process were made to address those effects. Corrosion experiments were conducted to support selection of suitable materials of construction for the major unit operations in the process. The bench scale unit operations were assembled into a continuous system to support steady state system testing. In the third budget period of the project, continuous system testing was conducted, including closed-loop operation of the absorber and desober systems. Slurries of GAP-0/GAP-0 carbamate/water mixtures produced in the absorber were pumped successfully to the desorber unit, and regenerated solvent was returned to the absorber. A techno-economic analysis, EH&S risk assessment, and solvent manufacturability study were completed.

20 FOSSIL-FUELED POWER PLANTS↗

Recovery Act: Oxy-Combustion Technology Development for Industrial-Scale Boiler Applications. Task 4 - Testing in Alstom's 15 MW th Boiler Simulation Facility

Alstom Power Inc. (Alstom), under U.S. DOE/NETL Cooperative Agreement No. DE-NT0005290, is conducting a development program to generate detailed technical information needed for application of oxy-combustion technology. The program is designed to provide the necessary information and understanding for the next step of large-scale commercial demonstration of oxy combustion in tangentially fired boilers and to accelerate the commercialization of this technology. The main project objectives include: Design and develop an innovative oxyfuel system for existing tangentially-fired boiler units that minimizes overall capital investment and operating costs; Evaluate performance of oxyfuel tangentially fired boiler systems in pilot scale tests at Alstom’s 15 MWth tangentially fired Boiler Simulation Facility (BSF); Address technical gaps for the design of oxyfuel commercial utility boilers by focused testing and improvement of engineering and simulation tools; Develop the design, performance and costs for a demonstration scale oxyfuel boiler and auxiliary systems; Develop the design and costs for both industrial and utility commercial scale reference oxyfuel boilers and auxiliary systems that are optimized for overall plant performance and cost; and, Define key design considerations and develop general guidelines for application of results to utility and different industrial applications. The project was initiated in October 2008 and the scope extended in 2010 under an ARRA award. The project is scheduled for completion by April 30, 2014. Central to the project is 15 MWth testing in the BSF, which provided in-depth understanding of oxy-combustion under boiler conditions, detailed data for improvement of design tools, and key information for application to commercial scale oxy-fired boiler design. Eight comprehensive 15 MWth oxy-fired test campaigns were performed with different coals, providing detailed data on combustion, emissions, and thermal behavior over a matrix of fuels, oxy-process variables and boiler design parameters. Significant improvement of CFD modeling tools and validation against 15 MWth experimental data has been completed. Oxy-boiler demonstration and large reference designs have been developed, supported with the information and knowledge gained from the 15 MWth testing. This report addresses the results from the 15 MWth testing in the BSF.

01 COAL, LIGNITE, AND PEAT↗

Mechanical and tribological properties of anodic Al coatings as a function of anodizing conditions

Enhanced wear and corrosion resistance properties are vital for numerous functional and decorative applications. Anodizing is a process frequently used to generate stable oxide coatings on metal surfaces, including aluminium (Al). In this work, we present an evaluation of process variables for optimized anodized coating properties using existing methods and as a baseline for novel coating development. A representative relatively pure Al alloy was chosen as a model system with a goal of finding conditions to achieve high wear coatings with retained ductility. AA5052 alloy coupons were anodized in two different electrolytes (sulfuric and phosphoric acid) to study the effects of anodizing conditions on the mechanical and tribological properties of the anodic coatings. Porosity was evaluated with microscopy, coating hardness was determined via nanoindentation, and tribological properties were characterized using a pin-on-disk tribometer. These measurements were correlated and a loading evaluation was performed to assess the optimum nanoindentation parameters for the use of representative coupons without the need for special processing prior to anodizing. The porosity and coating thickness were found to depend on the anodizing time and the type of electrolyte. Thicker and harder anodic coatings were generated in sulfuric acid compared to phosphoric acid. Porosity studies of the anodic coatings generated in phosphoric acid revealed that coating porosity decreased as the anodizing time increased. Both electrolytes generated anodic coatings with improved tribological properties (friction coefficient and dimensional wear rate), and an optimum processing time was identified for best wear properties.

36 MATERIALS SCIENCE↗

Modeling of deposit formation in mesoporous substrates via atomic layer deposition: Insights from pore‐scale simulation

Atomic layer deposition (ALD) has been a promising technique in fabricating membranes and tuning their properties with a precision at the atomic level. Fabrication of zeolitic imidazolate framework (ZIF) membranes using the ligand-induced permselectivation (LIPS) method starts with the formation of an oxide in a mesoporous substrate by ALD and is followed by the transformation of this oxide to ZIF using imidazolate vapor treatment. The objective of the ALD step is to block the mesopores with a thin deposit, that is, one with small penetration depth and small thickness on the top surface of the substrate. Unlike typical ALD on nonporous substrates, where all available sites react per ALD cycle, thin deposit formation in a mesoporous substrate requires that only a small fraction of the available deposition sites (i.e., close to the substrate surface) is subjected to ALD. Consequently, reactant dosing and duration of pulses are important process variables which, together with diffusion and reaction kinetics determine the deposit structure. Quantitative understanding of the interplay of these variables and phenomena can enable the rational design of ALD within mesoporous substrates. Here, we extend our earlier modeling effort considering the coexistence of ALD both inside the pores and on the external surface of the substrate. Finite-volume based models were developed and validated to simulate the two distinct modes of deposition cycle by cycle. The total mass uptake of the substrate with ALD cycles can be predicted using the combined surface deposition and pore reaction–diffusion models as affirmed by in situ quartz crystal microbalance experimental data. The ALD reactor model combined with the deposition model can accurately capture the number of ALD cycles needed to block the pores of the substrate. Based on the model, we designed a modified ALD process and examined the performance of the corresponding LIPS membranes. Furthermore, the present modeling work provides a new understanding of the deposit formation via ALD within mesoporous substrates for a variety of membrane applications.

atomic layer deposition↗

Micromechanical Surrogate Machine Learning Model for Creep Deformation Modeling

Process variability during the manufacture of gas turbine engine hot section components can significantly affect the material’s resulting microstructure. In casting, for instance, geometric variation within a component (thin sections versus thick sections, radial location) influences cooling rates and the resulting grain size. The high temperature creep response is known to be sensitive to grain size owing to a diffusional creep mechanism which occurs more readily along grain boundaries. Microstructural variation correspondingly drives mechanical behavior which propagates into component scale performance uncertainty. These factors are essential when planning inspection, maintenance, and repair strategies within a reliability framework. These benefits provide opportunities to increase overall energy efficiency through refined margins. Critically, there is an opportunity to bolster existing data-driven reliability models using physics-driven process-structure-property relations. Here we present recent work establishing a framework for evaluating the probabilistic creep performance of high-temperature materials. A novel microstructure-sensitive crystal plasticity finite element model is established that captures both grain boundary and crystallographic deformation effects. The computationally expensive physics model is calibrated using a statistical approach and this high-fidelity model is subsequently used to train a computationally efficient machine learning surrogate model. The surrogate model is essential for sampling a large ensemble of simulated structure-property pair results. The ensemble data are then mined to extract salient trends to be incorporated into a microstructure-sensitive reliability model. The proposed approach represents a novel way to capture microstructure-sensitive trends from physics-based models within a modern reliability framework.

Fernandez-Zelaia, Patxi [ORNL]↗

Dynamic modeling and control of a solid-sorbent CO{sub 2} capture process with two-stage bubbling fluidized bed adsorber reactor

Solid-sorbent-based CO{sub 2} capture processes have strong potential for reducing the overall energy penalty for post-combustion capture from the flue gas of a conventional pulverized coal power plant. However, the commercial success of this technology is contingent upon it operating over a wide range of capture rates, transient events, malfunctions, and disturbances, as well as under uncertainties. To study these operational aspects, a dynamic model of a solid-sorbent-based CO{sub 2} capture process has been developed. In this work, a one-dimensional (1D), non-isothermal, dynamic model of a two-stage bubbling fluidized bed (BFB) adsorber-reactor system with overflow-type weir configuration has been developed in Aspen Custom Modeler (ACM). The physical and chemical properties of the sorbent used in this study are based on a sorbent (32D) developed at National Energy Technology Laboratory (NETL). Each BFB is divided into bubble, emulsion, and cloud-wake regions with the assumptions that the bubble region is free of solids while both gas and solid phases coexist in the emulsion and cloud-wake regions. The BFB dynamic model includes 1D partial differential equations (PDEs) for mass and energy balances, along with comprehensive reaction kinetics. In addition to the two BFB models, the adsorber-reactor system includes 1D PDE-based dynamic models of the downcomer and outlet hopper, as well as models of distributors, control valves, and other pressure-drop devices. Consistent boundary and initial conditions are considered for simulating the dynamic model. Equipment items are sized and appropriate heat transfer options, wherever needed, are provided. Finally, a valid pressure-flow network is developed and a lower-level control system is designed. Using ACM, the transient responses of various process variables such as flue gas and sorbent temperatures, overall CO{sub 2} capture, level of solids in the downcomer and hopper have been studied by simulating typical disturbances such as change in the temperature, flowrate, and composition of the flue gas. To maintain the overall CO{sub 2} capture at a desired level in face of the typical disturbances, two control strategies were considered–a proportional-integral-derivative (PID)-based feedback control strategy and a feedforward-augmented feedback control strategy. Dynamic simulation results show that both the strategies result in unacceptable overshoot/undershoot and a long settling time. To improve the control system performance, a linear model predictive controller (LMPC) is designed. In summary, the overall results illustrate how optimizing the operation and control of carbon capture systems can have a significant impact on the extent and the rate at which commercial-scale capture processes will be scaled-up, deployed, and used in the years to come.

20 FOSSIL-FUELED POWER PLANTS↗

Fast and accurate reduced-order modeling of a MOOSE-based additive manufacturing model with operator learning

One predominant challenge in additive manufacturing (AM) is to achieve specific material properties by manipulating manufacturing process parameters during the runtime. Such manipulation tends to increase the computational load imposed on existing simulation tools employed in AM. The goal of the present work is to construct a fast and accurate reduced-order model (ROM) for an AM model developed within the Multiphysics Object-Oriented Simulation Environment (MOOSE) framework, ultimately reducing the time/cost of AM control and optimization processes. Our adoption of the operator learning (OL) approach enabled us to learn a family of differential equations produced by altering process variables in the laser’s Gaussian point heat source. More specifically, we used the Fourier neural operator (FNO) and deep operator network (DeepONet) to develop ROMs for time-dependent responses. Furthermore, we benchmarked the performance of these OL methods against a conventional deep neural network (DNN)-based ROM. Ultimately, we found that OL methods offer comparable performance and, in terms of accuracy and generalizability, even outperform DNN at predicting scalar model responses. The DNN-based ROM afforded the fastest training time. Furthermore, all the ROMs were faster than the original MOOSE model yet still provided accurate predictions. FNO had a smaller mean prediction error than DeepONet, with a larger variance for time-dependent responses. Unlike DNN, both FNO and DeepONet were able to simulate time series data without the need for dimensionality reduction techniques. Finally, the present work can help facilitate the AM optimization process by enabling faster execution of simulation tools while still preserving evaluation accuracy.

36 MATERIALS SCIENCE↗

Modeling of the Kinetics of Carbonitride Precipitation Process in High-Strength Low-Alloy Steels Using Cellular Automata Method

Proposition of a cellular automata (CA) model of carbonitride precipitation to simulate image of microstructure in HSLA steels and to predict the mechanical properties is presented in the paper. CA model proved to be very efficient in modeling various phenomena in material science. Numerical modeling played an important role in development of new processing technologies taking advantage of precipitation. By modeling, we mean a mathematical description of the relation between the main process variables and the resulting material properties, based on sound physical principles. In microalloyed steels, the microalloying elements Ti, Nb and V are added in order to control their microstructure and mechanical properties. High chemical affinity of these elements for interstitials (C, N) results in precipitation of binary compound, nitrides and carbides and products of their mutual solubility—carbonitrides. The model accounts for an increase in dislocation density due to plastic deformation and predicts kinetics of precipitation as well as shape of precipitates.

36 MATERIALS SCIENCE↗

Rate-based process modeling study of CO{sub 2} capture with aqueous monoethanolamine solution

Rate-based process modeling technology has matured and is increasingly gaining acceptance over traditional equilibrium-stage modeling approaches. Recently comprehensive pilot plant data for carbon dioxide (CO{sub 2}) capture with aqueous monoethanolamine (MEA) solution have become available from the University of Texas at Austin. The pilot plant data cover key process variables including CO{sub 2} concentration in the gas stream, CO{sub 2} loading in lean MEA solution, liquid to gas ratio, and packing type. In this study, we model the pilot plant operation with Aspen RateSep, a second generation rate-based multistage separation unit operation model in Aspen Plus. After a brief review of rate-based modeling, thermodynamic and kinetic models for CO{sub 2} absorption with the MEA solution, and transport property models, we show excellent match of the rate-based model predictions against the comprehensive pilot plant data and we validate the superiority of the rate-based models over the traditional equilibrium-stage models. We further examine the impacts of key rate-based modeling options, i.e., film discretization options and flow model options. The rate-based model provides excellent predictive capability, and it should be very useful for design and scale-up of CO{sub 2} capture processes.

01 COAL, LIGNITE, AND PEAT↗