SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
For flexibility in forming a curved surface, a honeycomb configuration using multiple pleats has proved superior to the usual core structures. The partial pleats formed in individual cell walls permit movements to and from the central axis without tearing.
Experimental results for 36" diameter honeycomb cylinders fabricated with thin (0.010") aluminum faces and cores prove that it is quite feasible to stabilize thin faces so they can be loaded Beyond the yield point. The effect of initial imperfections and the various modes of failure are discussed.
The Ryan VZ-3RY V/STOL test vehicle was flight tested over the airspeed range from 80 knots to below 6 knots. The deflected slipstream concept proved to be better suited to STOL than VTOL operation. Adverse ground effects prevented operation close to the ground at speeds less than 20 knots and below approximately 15 feet altitude. Steep glide slopes to landing (up to -16 deg) at approximately 40 knots were achieved, but steep, slow, descending flight did not appear feasible. Full-span leading-edge slats markedly increased the descent capability and reduced the minimum level flight speed.
Ablation analysis of tektites and their parent bodies by fusion of opaque siliceous stone into glass by aerodynamic heating to prove tektite origin
Geographical distribution in southeast asian strewn field of tektites used to prove asteroid impact hypothesis of tektite origin
This is a continuation of two monographs bearing the same general title already published by the author under the auspices of the Publishing House of Khar'kov University. It deals with the elastic post-buckling behavior of a cylindrical shell stressed in torsion. In particular, the critical loads are determined. Generally speaking, the exposition is on an elementary level and intended for a wide circle of readers with a knowledge of the elements of shell theory and differential geometry. It will prove useful to design engineers, mechanical engineering students, and scientists interested in the theory of shells.
In establishing the existence of periodic solutions for nonautonomous differential equations of the form x = g(x, t), where g is periodic in t of period ω for fixed x, it is often convenient to consider the translation operator T(x(t)) = x(t + ω). If corresponding to each initial vector chosen in an appropriate region there corresponds a unique solution of our equation, then periodicity may be established by proving the existence of a fixed point under T. This same technique is also useful for more general functional equations and can be extended in a number of interesting ways. In this paper we shall consider a variable type of translation operator which is useful in investigating periodicity for autonomous differential and functional equations where the period involved is less obvious.
This report describes some of the development tests conducted at Marshall Space Flight Center on sound suppressor models. These devices are designed to reduce the sound radiated into the atmosphere from the exhaust jets of large rocket engines. From theoretical considerations, the overall sound reduction capability of the tested models was expected to amount to 40 decibels. However, residual sound, radiated from the rocket engine and its installation, limited the attainable overall suppression to 24 decibels. Suppression of very low sound frequencies remains a special area of endeavor in future investigations. The models were designed to be self-contained. They proved to possess very good operational characteristics.
In January, 1964, a test program was begun on the thermal design of the Ranger Block III Spacecraft. The tests were performed i n the newly operational JPL 25' Space Simulator over a period of 6 months . The objectives of these tests were two-fold: A. To evaluate the 25' Space Simulator as a facility for proving the thermal design of spacecrafts, and B. To verify .the thermal design of the Ranger Block III spacecraft. These two objectives are complimentary in the test series performed and are difficult to separate into distinct categories. An important part of the first objective was to learn what type of test preparation, instrumentation, and analysis was required for the meaningful evaluation of test data from the 25' Space Simulator tests. Although some experience had been gained in testing of components and incomplete spacecrafts in smaller solar simulation chambers during the early part of the Ranger program, we knew little about testing of a complete spacecraft in the 25' Space Simulator when this test program began. Test analysis requires that the energy absorbed by various spacecraft components be known. This requires a knowledge of the area of solar absorption or sunlit area, the solar energy flux density on the area, and the effective absorptance of that area. Most of the problems encountered were associated with the determination of the last two quantities since the sunlit area may be obtained directly by inspection of spacecraft surfaces. This paper will present a discussion of our experiences during the Ranger Block III thermal test series on the Thermal Test Model (TCM). The TCM was thermally equivalent to the flight type Ranger spacecraft except for the lack of an antenna dish and solar panels. Flight type structural hardware was used with surface finishes equivalent to those of the flight spacecraft. Aluminum blocks simulated the spacecraft electronics thermal masses with resistance heaters simulating the electronic power dissipation. The discussion will be presented in a semi-chronological order and will be divided into the following areas: 1. Determination of solar simulation flux density on spacecraft surfaces. 2. Problems related to decollimation of the solar simulation source. 3. Determination of effective absorptance in the solar simulation spectrum.
Inaccessible-Non Repairable- Costly: The meaning of these words is absolute in the event of a complete failure of an orbiting spacecraft. Adequate design, or rather, minimizing chance of failure, challenges all scientists and engineers. Where experience has not been developed, the risk involved in a new application must be weighed against the consequence of a design failure. In space work, the spectrum of consequence is extremely wide. It ranges from loss of scientific data on one hand, to loss of life on the other.. There is little question that knowledge of the space environment and its effects must be determined to produce reliable spacecraft. Tests to prove the design must be performed with equipment capable of simulating the effects of the environment in which the design is to operate. This does not necessarily mean that the natural environment must be duplicated. The degree of environmental simulation that should be achieved depends primarily upon the significance of the physical effects it causes. The purpose of space vacuum simulation in an environmental test program should be accurately conceived and the testing phased to obtain maximum information from the limited samples available for test. This discussion is confined to some of the factors involved in simulating the effects of space vacuum environment. This survey is by no means complete, but will touch on some of the highlights in this field: 1. A description of the environment 2. The level of simulation necessary to evaluate its effects 3. Test equipment capability 4. Experience in test 5. Experience in orbit 6. Observations & future emphasis
The lower‐bounds method presented by Löwdin in the preceding paper has been applied to oscillators perturbed by third‐ and fourth‐power terms in the potential‐energy expression. For favorable cases agreement between upper and lower bounds is easily carried to many more figures than are likely to be physically significant. In many cases the lower bounds agreed more closely to the true eigenvalue than did the corresponding upper bounds. For a given basis set, this method gives closer bounds than that of Bazley and Fox, except for energy levels too high to be satisfactorily treated in the given basis. The only disadvantage found was that for close bounds double precision proved necessary, indicating more than ordinary loss of computational accuracy.
A master equation is derived to describe internal relaxation processes in molecular systems with a relatively small number of degrees of freedom. It is an inhomogeneous equation, taking into account nondiagonal elements of the coarse‐grained density matrix which prove to be the most relevant ones for the problem under consideration. Various relaxational time scales, inherent in a molecular system, can thus be shown to exist. Relaxation mechanisms and equilibrium states on these time scales can be determined. The general character and different types of solutions of the master equation are investigated. The theory is applied to internal vibrational relaxation and intramolecular rearrangement (isomerization) reactions.
Computer program analyzes the designs of critical systems that will either prove the design is free of single-point failures or detect each member of the population of single-point failures inherent in a system design. This program should find application in the checkout of redundant circuits and digital systems.
The mode of satellite tracking adopted at the Goonhilly earth station is to steer the aerial primarily by means of predicted data computed from the satellite orbital parameters and to superimpose, during the passage of the satellite, corrections to remove any prediction errors or aberrations due the transmission path. Predictions have proved to be highly accurate for satellites having a high mass to projected area ratio orbiting at altitudes at which air drag is very small; hence the corrections are small and infrequent.
High power continuous wave radar transmitter for use as planetary radar system and as proving ground for equipment NASA space program
General theory to prove existence of class of two weight codes
A digital distributed parameter model was used to study the effects of propellant-feed- system coupling and various hydraulic parameters on the analytical prediction of chugging instabilities. Coupling between the combustion chamber and feed system was controlled by varying the compliance of the injector-dome region. The coupling with the feed system above the pump was varied by changing the amount of cavitation compliance at the pump inlet. The stability limits and chugging frequencies proved to be strongly dependent on the degree of feed-system coupling. The maximum stability condition occurred with intermediate coupling. Under conditions of a high degree of feed-system-combustor coupling, the stability limits and chugging frequencies were primarily dependent on the feed-system characteristics; the responses were characterized by beating patterns. For the system analyzed, the pump suction line had little effect on the stability limits or chugging frequencies. Beating, present under the condition of near zero injector -dome compliance, was eliminated when the suction line was decoupled by employing a sufficiently high value of pump-inlet compliance. Under conditions of maximum feed-system coupling, the magnitude and distribution of line losses in the discharge line had a significant effect on the stability limits but had negligible effect on the chugging frequency and beating characteristics. Also, the length of the discharge line greatly affected the stability limits, chugging frequency, and beating characteristics. The length of the suction line, however, had little effect on the stability limits and chugging frequency but did influence the beating pattern. A resistive-shunt device attached to the pump discharge line to suppress chugging was investigated. The analysis showed that the device was effective under conditions of high feed-system coupling.
Time optimal control for parabolic equations, proving bang-bang principle, smoothness, existence of minimum, etc