Search NASA⌕ Search

SEARCH · Search NASA

Results for “RESIDUAL STRESSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

High stereographic resolution texture and residual stress evaluation using time-of-flight neutron diffraction

Neutron diffraction texture measurements provide bulk averaged textures with excellent grain orientation statistics, even for large-grained materials, owing to the probed volume being of the order of 1 cm 3 . Furthermore, crystallographic parameters and other valuable microstructure information such as phase fraction, coherent crystallite size, root-mean-square microstrain, macroscopic or intergranular strain and stress, etc. can be derived from neutron diffractograms. A procedure for combined high stereographic resolution texture and residual stress evaluation was established on the pulsed-neutron-source-based engineering materials diffractometer TAKUMI at the Materials and Life Science Experimental Facility of the Japan Proton Accelerator Research Center, through division of the neutron detector panel regions. Pole figure evaluation of a limestone standard sample with a well known texture suggested that the precision obtained for texture measurement is comparable to that of the established neutron beamlines utilized for texture measurement, such as the HIPPO diffractometer at the Los Alamos Neutron Science Center (New Mexico, USA) and the D20 angle-dispersive neutron diffractometer at the Institut Laue–Langevin (Grenoble, France). A high-strength martensite–austenite multilayered steel was employed for further verification of the reliability of simultaneous Rietveld analysis of multiphase textures and macro stress tensors. By using a texture-weighted geometric mean micromechanical (BulkPathGEO) model, a macro stress tensor analysis with a plane stress assumption showed a rolling direction–transverse direction (RD–TD) in-plane compressive stress (about –330 MPa) in the martensite layers and an RD–TD in-plane tensile stress (about 320 MPa) in the austenite layers. The phase stress partitioning was ascribed mainly to the additive effect of the volume expansion during martensite transformation and the linear contraction misfit between austenite layers and newly transformed martensite layers during the water quenching process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE Final Report: A Unified Understanding of Residual Stress in Thin Films: Kinetic Models, Experiments and Simulations

Thin films are critical for a wide range of advanced technologies. However, the deposited films often have high levels of residual stress that can limit their performance or lead to failure. The stress is known to depend on many variables, including the processing conditions, type of material, deposition technique and the film’s microstructure. The goal of this DOE program was to develop a fundamental understanding of how the different processes that control thin film growth under different conditions can be related to the development of stress. In the program, systematic experiments were performed or analyzed that related the stress to the processing conditions that were used. Measurements of stress were obtained for films that were grown at different rates, different solutions (for electrodeposition), different particle energies (for sputter deposition) and different microstructures. Based on this data, models were developed to explain the observed dependence on the different parameters. The models were based on considering the balance among different stress-inducing mechanism occurring as the film grows (for both non-energetic and energetic deposition). Comparison of the model predictions with the experiments enabled the kinetic parameters to be determined for different materials. The resulting model equations provide a comprehensive picture of how stress changes with the processing conditions that can be used to optimize the growth of thin films.

36 MATERIALS SCIENCE↗

Compressional residual stress in Bastogne boudins revealed by synchrotron X-ray microdiffraction

Lattice distortions in crystals can be mapped at the micron scale using synchrotron X-ray Laue microdiffraction (μXRD). From lattice distortions the shape and orientation of the elastic strain tensor can be derived and interpreted in terms of residual stress. We apply the new method to vein quartz from the original boudinage locality at Bastogne, Belgium. Furthermore, a long-standing debate surrounds the kinematics of the Bastogne boudins. The μXRD measurements reveal a shortening residual elastic strain, perpendicular to the vein wall, corroborating the model that the Bastogne boudins formed by layer-parallel shortening and not by layer-parallel extension, as is in the geological community generally inferred by the process of boudinage.

58 GEOSCIENCES↗

Prediction of residual stresses in additively manufactured parts using lumped capacitance and classical lamination theory

Several industries are interested in Laser Powder Bed Fusion (L-PBF) Additively Manufactured (AM) metal parts because their designs can be made arbitrarily complex while retaining bulk-type material properties. However, the residual stresses (RS) and distortions caused by the heat gradients inherent to L-PBF processes are detrimental to the structural integrity of the parts and must be taken into consideration during the part design cycle. Predicting the state of stresses in as-built 3D printed parts is a difficult problem that is typically approached with the use of transient thermomechanical Finite Element Models (FEMs). However, the nonlinearities associated with AM processes are difficult to capture in these FEMs without increasing the computational cost of the simulation, limiting their ability to be incorporated into practical design cycles. This work presents a novel analytical framework that combines lumped capacitance nonlinear heat transfer with time dependent classical lamination theory to efficiently and accurately predict RS in as-built L-PBF parts without the need of FEMs. The simulation was compared to Neutron Diffraction (ND) residual strain measurements taken at Oak Ridge National Laboratories (ORNL) as well as Synchrotron X-ray Diffraction (XRD) strain data published by the National Institute of Standards and Technology (NIST). The simulation predictions and the experimental data showed excellent agreement for the in-plane strain directions, and general agreement for the out of plane strain component, highlighting an area where further development can be implemented.

42 ENGINEERING↗

Heat treatment to anneal residual stresses during additive manufacturing

An additive manufacturing system having a heat source for melting powder particles in a desired shape and pattern to produce a product. A secondary heat source is used for heat treating the product to achieve heat treatment. The secondary heat source is used to peen or anneal residual stresses caused by the additive manufacturing process.

36 MATERIALS SCIENCE↗

An efficient numerical model for predicting residual stress and strain in parts manufactured by laser powder bed fusion

Abstract Computational modeling of additively manufactured structures plays an increasingly important role in product design and optimization. For laser powder bed fusion processes, the accurate modeling of stress and distortion requires large amount of computational cost due to very localized heat input and evolving complex geometries. The current study takes advantage of a graphics processing unit accelerated explicit finite element analysis code and approximated heat conduction analysis to predict the macroscopic thermo-mechanical behavior in laser selective melting. Adjacent layers and tracks were lumped to reduce the number of time steps and elements in the finite element model. The effects of track and layer grouping on prediction accuracy and solution efficiency are investigated to provide a guidance for a cost-effective simulation. Thin-wall builds from Inconel alloy 625 (IN625) powders were simulated by applying the developed modeling approach to get the detailed residual stress and distortion at a computational speed 50 times higher than conventional approach. Under repeated heating and cooling cycles, a high tensile stress was produced near surfaces of a build due to a larger shrinkage on surface than that in central area. It is also shown that horizontal stresses concentrate near the root and top layers of the IN625 build. The predicted residual elastic strain distribution was validated by the experimental measurement using x-ray synchrotron diffraction.

36 MATERIALS SCIENCE↗

Spectral Modeling of Residual Stress and Stored Elastic Strain Energy in Thermal Barrier Coatings

Solutions to the thermoelastic problem are important for characterizing the response under temperature change of refractory systems. This work extends a spectral fast Fourier transform (FFT) technique to analyze the thermoelastic behavior of thermal barrier coatings (TBCs), with the intent of probing the local origins of failure in TBCs. The thermoelastic FFT (teFFT) approach allows for the characterization of local thermal residual stress and strain fields, which constitute the origins of failure in TBC systems. A technique based on statistical extreme value theory known as peaks-over-threshold (POT) is developed to quantify the extreme values ("hot spots") of stored elastic strain energy (i.e., elastic energy density, or EED). The resolution dependence of the teFFT method is assessed through a sensitivity study of the extreme values in EED. The sensitivity study is performed both for the local (point-by-point) eld distributions as well as the grain scale eld distributions. A convergence behavior to a particular distribution shape is demonstrated for the local elds. The grain scale fields are shown to exhibit a possible convergence to a maximum level of EED. To apply the teFFT method to TBC systems, 3D synthetic microstructures are created to approximate actual TBC microstructures. The morphology of the grains in each constituent layer as well as the texture is controlled. A variety of TBC materials, including industry standard materials and potential future materials, are analyzed using the teFFT. The resulting hot spots are quantified using the POT approach. A correlation between hot spots in EED and interface rumpling between constituent layers is demonstrated, particularly for the interface between the bond coat (BC) and the thermally grown oxide (TGO) layer.

36 MATERIALS SCIENCE↗

Development of Laser Ultrasonic Device for Residual Stress Measurement in Welded Structures

A CRADA project was performed between BNL and SpectraQuest, Inc. of Richmond, Virginia under the auspices of IPP with the DOE support. The purpose was to jointly support Prokhorov General Physics Institute (GPI), Russian Academy of Sciences of Russia to develop a prototype Laser Ultrasonic Impact Testing (LUIT) device which could be commercialized and marketed. The device is based on laser-generated ultrasonic waves and can be used for measuring residual stresses in welded structures using a nondestructive technique. The work was performed from October 1, 2003 to September 30, 2009. The project resulted in development and validation of a prototype LUIT device. GPI - BNL – SpectraQuest partnership developed the LUIT device to the point where it could be commercialized and marketed for the special applications in the manufacturing field.

42 ENGINEERING↗

FLAW STABILITY ANALYSIS OF SURFACE CRACKS IN DOE STANDARD CANISTERS UNDER OPERATION LOADS AND WELDING RESIDUAL STRESSES

There are over 3000 commercial spent nuclear fuel (SNF) storage canisters that are made of stainless steel and planned for multi-purpose functions of SNF handling: interim storage, transportation, and ultimate disposal at a future SNF disposition location. To date, many multi-purpose canisters (MPC) are located in coastal regions for long-term storage. The canisters are fabricated by welding, and post-welding heat treatment is not required for relieving welding residual stresses (WRS). As a result, these canisters may be susceptible to chloride induced stress corrosion cracking (CISCC) due to the chloride-bearing marine salts. The flaw stability analysis of MPC canisters was performed at SRNL (i.e., PVP2016-4935 and PVP2016-63887) for through-wall flaws and for surface flaws respectively, where WRS was considered, and the failure assessment diagram (FAD)-based fracture mechanics method codified by API 579-1/ASME FFS-1-2007 Edition was adopted.

DOE standard canister↗

Residual stress of controlled atmosphere plasma spray blended metal deposits measured via in-situ substrate curvature method

The preliminary use of the in-situ curvature measurement technique for analyzing the planar stress evolution of controlled atmosphere plasma spray (CAPS) refractory metal deposits was performed with SNL-NM org. 1834’s CAPS system. A porous refractory metal exemplar of Ta-Nb was sprayed onto Ni-200, Ti-6Al-4V, and Al 7075-T6 substrates using a constant plasma torch parameter setting and deposition toolpath. Residual stresses of the deposits were found to be largely influenced by the substrate coefficient of thermal expansion and were calculated to be 49, 90, and -136 MPa for Ni 200, Ti-6Al-4V, and Al 7075-T6, respectively. The “Evolving stress” of the Ta-Nb deposits, which more accurately describes the mean intrinsic splat quenching stress of the spray material during deposition, was calculated to be 67, 92, and 129 MPa for Ni-200, Ti-6Al-4V, and Al 7075-T6, respectively. Notable difference in curvature measurement for the 1st coating pass for the Al 7075- T6 substrate was observed, with interface micrograph evidence suggesting potential softening and/or melting of the Al 7075-T6 substrate surface during deposition. Substrate temperature measurements prior to Ta-Nb deposition were used to calculate thermal energy absorbed from the hot gas plume by the different substrates and were found to correlate to the substrate’s thermal effusively. These calculated thermal energies were also found to be ~10 to 15% of the calculated energy output from the plasma torch’s nozzle exit for these experimental conditions.

36 MATERIALS SCIENCE↗

Neutron diffraction measurement of residual stresses, dislocation density and texture in Zr-bonded U-10Mo “mini” fuel foils and plates

Here, Al clad U-10Mo fuel plates are being considered for conversion of several research reactors from high-enriched to low-enriched U fuel. Neutron diffraction measurements of the textures, residual phase stresses, and dislocation densities in the individual phases of the mini-foils throughout several processing steps and following hot-isostatic pressing to the Al cladding, have been completed. Recovery and recrystallization of the bare U-10Mo fuel foil, as indicated by the dislocation density and texture, are observed depending on the state of the material prior to annealing and the duration and temperature of the annealing process. In general, the cladding procedure significantly reduces the dislocation density, but the final state of the clad plate, both texture and dislocation density, depends strongly on the final processing step of the fuel foil. In contrast, the residual stress state of the final plate is dominated by the thermal expansion mismatch of the constituent materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Toward large-scale simulation of residual stress and distortion in wire and arc additive manufacturing

In this study, we aim to advance the structural analysis of wire and arc additive manufacturing (WAAM) by considering the thermomechanical features inherent in direct energy deposition. Simulation approaches including the iterative substructure method (ISM), dynamic mesh refining method (DMRM), and graphics processing unit (GPU) based explicit finite element method (FEM) were developed for accelerating additive manufacturing stress analysis that is very time consuming by conventional numerical methods. ISM and DMRM take advantage of the strong nonlinearity phenomenon near the moving heat source by reducing the global iterations and refining the local mesh, respectively. In addition to the use of GPUs, the explicit FEM is accelerated by a time scaling technique based on the inherent strain concept. The residual stress and distortion of two large builds were analyzed, showing very consistent numerical results and good agreement with experiments. Compared with the commercial software Abaqus, the novel approaches reduced the computational cost substantially without compromising accuracy. The GPU code showed the highest computational efficiency (30~70×), while DMRM and ISM had acceleration factors of 9× and 3×, respectively. Finally, such high-fidelity modeling approaches will be very useful for building up a digital twin of WAAM to reduce development time and cost.

36 MATERIALS SCIENCE↗

Flaw Stability Considering Residual Stress for Aging Management of Spent Nuclear Fuel Multiple-Purpose Canisters

A typical multipurpose canister (MPC) is made of austenitic stainless steel and is loaded with spent nuclear fuel assemblies. Because heat treatment for stress relief is not required for the construction of the MPC, the canister is susceptible to stress corrosion cracking in the weld or heat affected zone regions under long-term storage conditions. Logic for flaw acceptance is developed should crack-like flaws be detected by Inservice Inspection. The procedure recommended by API 579-1/ASME FFS-1, Fitness-for-Service, is used to calculate the instability crack length or depth by failure assessment diagram. It is demonstrated that the welding residual stress has a strong influence on the results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Densification and residual stress induced by CO2 laser-based mitigation of SiO2 surfaces

Knowing the ultimate surface morphology resulting from CO{sub 2} laser mitigation of induced laser damage is important both for determining adequate treatment protocols, and for preventing deleterious intensification upon subsequent illumination of downstream optics. Physical effects such as evaporation, viscous flow and densification can strongly affect the final morphology of the treated site. Evaporation is a strong function of temperature and will play a leading role in determining pit shapes when the evaporation rate is large, both because of material loss and redeposition. Viscous motion of the hot molten material during heating and cooling can redistribute material due to surface tension gradients (Marangoni effect) and vapor recoil pressure effects. Less well known, perhaps, is that silica can densify as a result of structural relaxation, to a degree depending on the local thermal history. The specific volume shrinkage due to structural relaxation can be mistaken for material loss due to evaporation. Unlike evaporation, however, local density change can be reversed by post annealing. All of these effects must be taken into account to adequately describe the final morphology and optical properties of single and multiple-pass mitigation protocols. We have investigated, experimentally and theoretically, the significance of such densification on residual stress and under what circumstances it can compete with evaporation in determining the ultimate post treatment surface shape. In general, understanding final surface configurations requires taking all these factors including local structural relaxation densification, and therefore the thermal history, into account. We find that surface depressions due to densification can dominate surface morphology in the non-evaporative regime when peak temperatures are below 2100K.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗