Search NASA⌕ Search

SEARCH · Search NASA

Results for “REYNOLDS NUMBER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Experimental studies of the boundary layer on an airfoil at low Reynolds numbers

An experimental wind tunnel investigation was carried out to study the effect of laminar separation bubbles on a NACA 66(3)-018 airfoil for Reynolds numbers less than 4.0 x 10 to the 5th. Leading edge laminar separation bubbles formed for angles of attack of approximately 7 to 12 deg. To study the leading edge separation bubble more closely, hotwire anemometer measurements were made in the airfoil a Reynolds number of 8.0 x 10 to the 4th. Velocity and turbulence intensity profiles were obtained and boundary layer parameters were calculated. Frequency spectra were also calculated at key points in the airfoil boundary layer for this case. Correlation of the anemometry data with static pressure distributions, and flow visualization data provided insight into laminar separation bubble behavior at low Reynolds numbers.

Jansen, B. J., Jr.↗
NASA NTRS1990

The Stealth Biplane: a Proposal in Response to a Low Reynolds Number Station Keeping Mission

The Stealth Biplane is conceived and constructed to serve as a remotely piloted vehicle designed to navigate a low-level figure-eight course at a target Reynolds number of 100,000. This flight vehicle will combine the latest in lightweight radio controlled hardware in conjunction with current low Reynolds number aerodynamic research to demonstrate feasible operation in a variety of applications. These potential low Reynolds number applications include high altitude atmospheric sampling, search and rescue, and even law enforcement. Design specs and fabrication technique are discussed.

Walsh, Timothy E.↗
NASA NTRS1982

The cryogenic wind tunnel for high Reynolds number testing

The development of cryogenic wind tunnels is reviewed with reference to the theory and advantages of cryogenic tunnels, problems common to wind tunnels and their solution, and application of cryogenic wind tunnels to high Reynolds number testing. It is shown that cryogenic wind tunnels can achieve full-scale Reynolds number with reasonable tunnel size, dynamic pressure, and drive power; the use of such tunnels also makes it possible to separate the effects of Reynolds number, Mach number, and aeroelasticity. Application of the cryogenic tunnel concept is illustrated by three examples, namely an atmospheric low-speed cryogenic tunnel, a 0.3-meter transonic cryogenic tunnel, and the National Transonic Facility now nearing completion.

Kilgore, R. A.↗
NASA NTRS1984

Hot wire in low Reynolds number flow

Progress reports were issued on the following experiments: (1) low Reynolds number flow phenomenon of periodic vortex shedding in the wake behind a cylinder as studied by applying the hot wire anemometer technique of flow measurement. The downstream diffusion of these shed vortices was of prime concern. An evaluation of the performance of the hot wire at low Reynolds number is also considered. (2) A brief examination of the back sections of the Wright Brothers wind tunnel circuits were conducted to establish whether or not gross flow deviations were present at corners, or turning vane regions. A calibration of the test sections was done. (3) The attractiveness of using rembedded grids for airfoil calculations modeled by the Euler equations was explored. These calculations were extended to C-type grids and then to Navier-Stokes calculations,

Kolb, M. A.↗
NASA NTRS1974

An experimental investigation of wall boundary layer transition Reynolds numbers in an expansion tube

Experimental measurements of boundary-layer transition in an expansion-tube test-gas flow are presented along with radial distributions of pitot pressure. An integral method for calculating constant Reynolds number lines for an expansion-tube flow is introduced. Comparison of experimental data and constant Reynolds number calculations has shown that for given conditions, wall boundary-layer transition occurs at a constant Reynolds number in an expansion-tube flow. Operating conditions in the expansion tube were chosen so that the effects of test-gas nonequilibrium on boundary-layer transition could be studied.

Weilmuenster, K. J.↗
NASA NTRS1976

Experimental investigation to validate use of cryogenic temperatures to achieve high Reynolds numbers in boattail pressure testing

An investigation has been conducted in the Langley 1/3 meter transonic cryogenic tunnel to validate the use of cryogenic temperatures to achieve high Reynolds numbers in nozzle boattail pressure testing. Tests were conducted at 0 degree angle of attack and at Mach numbers of 0.60, 0.85, and 0.90 on two wing-body configurations with differing boattail geometries. Test data were obtained by using two different techniques, the cryogenic method and the conventional method, to obtain the same Reynolds number. Later, the test data obtained from the two techniques on boattail pressure coefficient distributions and pressure drag coefficients were compared; results from the comparisons show excellent repeatability for all test conditions and indicate no measurable errors when using cryogenic temperatures to achieve high Reynolds numbers for nozzle boattail pressure testing.

Reubush, D. E.↗
NASA NTRS1975

High Reynolds number transonic flow simulation

A code has been developed for simulating high Reynolds number transonic flow fields of arbitrary configuration. An explicit finite-difference method with time splitting is used to solve the time-dependent equations for compressible turbulent flow. A nonorthogonal computational mesh of arbitrary configuration facilitates the description of the flow field. The code is applied to simulate the flow over a two-dimensional 18 percent thick circular-arc biconvex airfoil at zero angle of attack for several different Reynolds numbers and a free-stream Mach number of 0.775.

Deiwert, G. S.↗
NASA NTRS1993

An investigation of small scales of turbulence in a boundary layer at high Reynolds numbers

The assumption that turbulence at large wave-numbers is isotropic and has universal spectral characteristics which are independent of the flow geometry, at least for high Reynolds numbers, has been a cornerstone of closure theories as well as of the most promising recent development in the effort to predict turbulent flows, viz. large eddy simulations. This hypothesis was first advanced by Kolmogorov based on the supposition that turbulent kinetic energy cascades down the scales (up the wave-numbers) of turbulence and that, if the number of these cascade steps is sufficiently large (i.e. the wave-number range is large), then the effects of anisotropies at the large scales are lost in the energy transfer process. Experimental attempts were repeatedly made to verify this fundamental assumption. However, Van Atta has recently suggested that an examination of the scalar and velocity gradient fields is necessary to definitively verify this hypothesis or prove it to be unfounded. Of course, this must be carried out in a flow with a sufficiently high Reynolds number to provide the necessary separation of scales in order unambiguously to provide the possibility of local isotropy at large wave-numbers. An opportunity to use our 12-sensor hot-wire probe to address this issue directly was made available at the 80'x120' wind tunnel at the NASA Ames Research Center, which is normally used for full-scale aircraft tests. An initial report on this high Reynolds number experiment and progress toward its evaluation is presented.

Wallace, James M.↗
NASA NTRS1937

Airfoil Section Characteristics as Affected by Variations of the Reynolds Number

Report presents the results of an investigation of a systematically chosen representative group of related airfoils conducted in the NACA variable-density wind tunnel over a wide range of Reynolds number extending well into the flight range. The tests were made to provide information from which the variations of airfoil section characteristics with changes in the Reynolds number could be inferred and methods of allowing for these variations in practice could be determined. This work is one phase of an extensive and general airfoil investigation being conducted in the variable-density tunnel and extends the previously published researches concerning airfoil characteristics as affected by variations in airfoil profile determined at a single value of the Reynolds number.

Jacobs, Eastman N↗
NASA NTRS1993

Prediction of stall and post-stall behavior of airfoils at low and high Reynolds numbers

An interactive boundary-layer method, together with the e(super n)-approach to the calculation of transition, has been used to predict the stall and post-stall behavior of airfoils at low and high Reynolds numbers. The turbulence model is based on the Cebeci-Smith algebraic eddy-viscosity formulation with improvements for strong pressure gradient effects and transitional flows at low Reynolds numbers. Comparison of calculated results for incompressible flows indicate good agreement with experiment for a wide range of Reynolds numbers. Preliminary calculations for low Mach number flows with this interactive method with compressibility corrections to the panel method indicate that, at a Mach number of 0.3, the compressibility effect on (C sub Q)max is not negligible.

Cebeci, T.↗
NASA NTRS1978

Flight-measured pressure characteristics of aft-facing steps in high Reynolds number flow at Mach numbers of 2.20, 2.50, and 2.80 and comparison with other data

The YF-12 airplane was studied to determine the pressure characteristics associated with an aft-facing step in high Reynolds number flow for nominal Mach numbers of 2.20, 2.50, and 2.80. Base pressure coefficients were obtained for three step heights. The surface static pressures ahead of and behind the step were measured for the no-step condition and for each of the step heights. A boundary layer rake was used to determine the local boundary layer conditions. The Reynolds number based on the length of flow ahead of the step was approximately 10 to the 8th power and the ratios of momentum thickness to step height ranged from 0.2 to 1.0. Base pressure coefficients were compared with other available data at similar Mach numbers and at ratios of momentum thickness to step height near 1.0. In addition, the data were compared with base pressure coefficients calculated by a semiempirical prediction method. The base pressure ratios are shown to be a function of Reynolds number based on momentum thickness. Profiles of the surface pressures ahead of and behind the step and the local boundary layer conditions are also presented.

Powers, S. G.↗
NASA NTRS2011

Flight Reynolds Number Testing of the Orion Launch Abort Vehicle in the NASA Langley National Transonic Facility

A 6%-scale unpowered model of the Orion Launch Abort Vehicle (LAV) ALAS-11-rev3c configuration was tested in the NASA Langley National Transonic Facility to obtain static aerodynamic data at flight Reynolds numbers. Subsonic and transonic data were obtained for Mach numbers between 0.3 and 0.95 for angles of attack from -4 to +22 degrees and angles of sideslip from -10 to +10 degrees. Data were also obtained at various intermediate Reynolds numbers between 2.5 million and 45 million depending on Mach number in order to examine the effects of Reynolds number on the vehicle. Force and moment data were obtained using a 6-component strain gauge balance that operated both at warm temperatures (+120 . F) and cryogenic temperatures (-250 . F). Surface pressure data were obtained with electronically scanned pressure units housed in heated enclosures designed to survive cryogenic temperatures. Data obtained during the 3-week test entry were used to support development of the LAV aerodynamic database and to support computational fluid dynamics code validation. Furthermore, one of the outcomes of the test was the reduction of database uncertainty on axial force coefficient for the static unpowered LAV. This was accomplished as a result of good data repeatability throughout the test and because of decreased uncertainty on scaling wind tunnel data to flight.

Chan, David T.↗
NASA NTRS2020

Optimization of Low Reynolds Number Airfoils for Martian Rotor Applications Using an Evolutionary Algorithm

The Mars Helicopter (MH) will be flying on the NASA Mars 2020 rover mission scheduled to launch in July of 2020. Research is being performed at the Jet Propulsion Laboratory (JPL) and NASA Ames Research Center to extend the current capabilities and develop the Mars Science Helicopter (MSH) as the next possible step for Martian rotorcraft. The low atmospheric density and the relatively small-scale rotors result in very low chord-based Reynolds number flows over the rotor airfoils. The low Reynolds number regime results in rapid performance degradation for conventional airfoils due to laminar separation without reattachment. Unconventional airfoil shapes with sharp leading edges are explored and optimized for aerodynamic performance at representative Reynolds-Mach combinations for a concept rotor. Sharp leading edges initiate immediate flow separation, and the occurrence of large-scale vortex shedding is found to contribute to the relative performance increase of the optimized airfoils, compared to conventional airfoil shapes. The oscillations are shown to occur independent from laminar-turbulent transition and therefore result in sustainable performance at lower Reynolds numbers. Comparisons are presented to conventional airfoil shapes and peak lift-to-drag ratio increases between 17% and 41% are observed for similar section lift.

Koning, Witold J.↗