Search NASA⌕ Search

SEARCH · Search NASA

Results for “REYNOLDS NUMBER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

High Reynolds number transonic flow simulation

A code has been developed for simulating high Reynolds number transonic flow fields of arbitrary configuration. An explicit finite-difference method with time splitting is used to solve the time-dependent equations for compressible turbulent flow. A nonorthogonal computational mesh of arbitrary configuration facilitates the description of the flow field. The code is applied to simulate the flow over a two-dimensional 18 percent thick circular-arc biconvex airfoil at zero angle of attack for several different Reynolds numbers and a free-stream Mach number of 0.775.

Deiwert, G. S.↗

An investigation of small scales of turbulence in a boundary layer at high Reynolds numbers

The assumption that turbulence at large wave-numbers is isotropic and has universal spectral characteristics which are independent of the flow geometry, at least for high Reynolds numbers, has been a cornerstone of closure theories as well as of the most promising recent development in the effort to predict turbulent flows, viz. large eddy simulations. This hypothesis was first advanced by Kolmogorov based on the supposition that turbulent kinetic energy cascades down the scales (up the wave-numbers) of turbulence and that, if the number of these cascade steps is sufficiently large (i.e. the wave-number range is large), then the effects of anisotropies at the large scales are lost in the energy transfer process. Experimental attempts were repeatedly made to verify this fundamental assumption. However, Van Atta has recently suggested that an examination of the scalar and velocity gradient fields is necessary to definitively verify this hypothesis or prove it to be unfounded. Of course, this must be carried out in a flow with a sufficiently high Reynolds number to provide the necessary separation of scales in order unambiguously to provide the possibility of local isotropy at large wave-numbers. An opportunity to use our 12-sensor hot-wire probe to address this issue directly was made available at the 80'x120' wind tunnel at the NASA Ames Research Center, which is normally used for full-scale aircraft tests. An initial report on this high Reynolds number experiment and progress toward its evaluation is presented.

Wallace, James M.↗

Airfoil Section Characteristics as Affected by Variations of the Reynolds Number

Report presents the results of an investigation of a systematically chosen representative group of related airfoils conducted in the NACA variable-density wind tunnel over a wide range of Reynolds number extending well into the flight range. The tests were made to provide information from which the variations of airfoil section characteristics with changes in the Reynolds number could be inferred and methods of allowing for these variations in practice could be determined. This work is one phase of an extensive and general airfoil investigation being conducted in the variable-density tunnel and extends the previously published researches concerning airfoil characteristics as affected by variations in airfoil profile determined at a single value of the Reynolds number.

Jacobs, Eastman N↗

Prediction of stall and post-stall behavior of airfoils at low and high Reynolds numbers

An interactive boundary-layer method, together with the e(super n)-approach to the calculation of transition, has been used to predict the stall and post-stall behavior of airfoils at low and high Reynolds numbers. The turbulence model is based on the Cebeci-Smith algebraic eddy-viscosity formulation with improvements for strong pressure gradient effects and transitional flows at low Reynolds numbers. Comparison of calculated results for incompressible flows indicate good agreement with experiment for a wide range of Reynolds numbers. Preliminary calculations for low Mach number flows with this interactive method with compressibility corrections to the panel method indicate that, at a Mach number of 0.3, the compressibility effect on (C sub Q)max is not negligible.

Cebeci, T.↗

Flight-measured pressure characteristics of aft-facing steps in high Reynolds number flow at Mach numbers of 2.20, 2.50, and 2.80 and comparison with other data

The YF-12 airplane was studied to determine the pressure characteristics associated with an aft-facing step in high Reynolds number flow for nominal Mach numbers of 2.20, 2.50, and 2.80. Base pressure coefficients were obtained for three step heights. The surface static pressures ahead of and behind the step were measured for the no-step condition and for each of the step heights. A boundary layer rake was used to determine the local boundary layer conditions. The Reynolds number based on the length of flow ahead of the step was approximately 10 to the 8th power and the ratios of momentum thickness to step height ranged from 0.2 to 1.0. Base pressure coefficients were compared with other available data at similar Mach numbers and at ratios of momentum thickness to step height near 1.0. In addition, the data were compared with base pressure coefficients calculated by a semiempirical prediction method. The base pressure ratios are shown to be a function of Reynolds number based on momentum thickness. Profiles of the surface pressures ahead of and behind the step and the local boundary layer conditions are also presented.

Powers, S. G.↗

Flight Reynolds Number Testing of the Orion Launch Abort Vehicle in the NASA Langley National Transonic Facility

A 6%-scale unpowered model of the Orion Launch Abort Vehicle (LAV) ALAS-11-rev3c configuration was tested in the NASA Langley National Transonic Facility to obtain static aerodynamic data at flight Reynolds numbers. Subsonic and transonic data were obtained for Mach numbers between 0.3 and 0.95 for angles of attack from -4 to +22 degrees and angles of sideslip from -10 to +10 degrees. Data were also obtained at various intermediate Reynolds numbers between 2.5 million and 45 million depending on Mach number in order to examine the effects of Reynolds number on the vehicle. Force and moment data were obtained using a 6-component strain gauge balance that operated both at warm temperatures (+120 . F) and cryogenic temperatures (-250 . F). Surface pressure data were obtained with electronically scanned pressure units housed in heated enclosures designed to survive cryogenic temperatures. Data obtained during the 3-week test entry were used to support development of the LAV aerodynamic database and to support computational fluid dynamics code validation. Furthermore, one of the outcomes of the test was the reduction of database uncertainty on axial force coefficient for the static unpowered LAV. This was accomplished as a result of good data repeatability throughout the test and because of decreased uncertainty on scaling wind tunnel data to flight.

Chan, David T.↗

Optimization of Low Reynolds Number Airfoils for Martian Rotor Applications Using an Evolutionary Algorithm

The Mars Helicopter (MH) will be flying on the NASA Mars 2020 rover mission scheduled to launch in July of 2020. Research is being performed at the Jet Propulsion Laboratory (JPL) and NASA Ames Research Center to extend the current capabilities and develop the Mars Science Helicopter (MSH) as the next possible step for Martian rotorcraft. The low atmospheric density and the relatively small-scale rotors result in very low chord-based Reynolds number flows over the rotor airfoils. The low Reynolds number regime results in rapid performance degradation for conventional airfoils due to laminar separation without reattachment. Unconventional airfoil shapes with sharp leading edges are explored and optimized for aerodynamic performance at representative Reynolds-Mach combinations for a concept rotor. Sharp leading edges initiate immediate flow separation, and the occurrence of large-scale vortex shedding is found to contribute to the relative performance increase of the optimized airfoils, compared to conventional airfoil shapes. The oscillations are shown to occur independent from laminar-turbulent transition and therefore result in sustainable performance at lower Reynolds numbers. Comparisons are presented to conventional airfoil shapes and peak lift-to-drag ratio increases between 17% and 41% are observed for similar section lift.

Koning, Witold J.↗

Study of Low Reynolds Number Effects on the Losses in Low-Pressure Turbine Blade Rows

Experimental data from jet-engine tests have indicated that unsteady blade row interactions and separation can have a significant impact on the efficiency of low-pressure turbine stages. Measured turbine efficiencies at takeoff can be as much as two points higher than those at cruise conditions. Several recent studies have revealed that Reynolds number effects may contribute to the lower efficiencies at cruise conditions. In the current study numerical experiments have been performed to study the models available for low Reynolds number flows, and to quantify the Reynolds number dependence of low-pressure turbine cascades and stages. The predicted aerodynamic results exhibit good agreement with design data.

Ashpis, David E.↗

Study of Low Reynolds Number Effects on the Losses in Low-Pressure Turbine Blade Rows

Experimental data from jet-engine tests have indicated that unsteady blade row interactions and separation can have a significant impact on the efficiency of low-pressure turbine stages. Measured turbine efficiencies at takeoff can be as much as two points higher than those at cruise conditions. Several recent studies have revealed that Reynolds number effects may contribute to the lower efficiencies at cruise conditions. In the current study numerical experiments have been performed to study the models available for low Reynolds number flows, and to quantify the Reynolds number dependence of low-pressure turbine cascades and stages. The predicted aerodynamic results exhibit good agreement with design data.

Dorney, Daniel J.↗

A study of the effects of Reynolds number and Mach number on constant pressure coefficient jump for shock-induced trailing-edge separation

The influence of Mach and Reynolds numbers as well as airfoil and planform geometry on the phenomenon of constant shock jump pressure coefficient for conditions of shock induced trailing edge separation (SITES) was studied. It was demonstrated that the phenomenon does exist for a wide variety of two and three dimensional flow cases and that the influence of free stream Mach number was not significant. The influence of Reynolds number was found to be important but was not strong. Airfoil and planform geometric characteristics were found to be very important where the pressure coefficient jump was shown to vary with the sum of: (1) airfoil curvature at the upper surface crest, and (2) camber surface slope at the trailing edge. It was also determined that the onset of SITES could be defined as a function of airfoil geometric parameters and Mach number normal to the leading edge. This onset prediction was shown to predict the angle of onset to within + or - 1 deg accuracy or better for about 90% of the cases studied.

Cunningham, Atlee M., Jr.↗

Reynolds number effects on the turbulence field in compressible boundary layers

Detailed experiments were conducted in a zero pressure gradient, supersonic turbulent boundary layer, including measurements of the three components of velocity fluctuations and the turbulent shear stress, for Reynolds numbers ranging from 11.7 million to 105 million at a freestream Mach number of 2.3. The mean flow measurements established the fully developed and equilibrium nature of the boundary layer. Measurements of the turbulence field show that the vertical and transverse fluctuations are essentially equal throughout the boundary layer at all Reynolds numbers, a feature that is different from observations in incompressible flows. The data show that the boundary layer exhibits similarity in the turbulence profiles for the entire Reynolds number range and agrees with previous compressible and incompressible data using Morkovin's scaling to account for compressibility effects.

Acharya, M.↗

The effects of turbulence and stator/rotor interactions on turbine heat transfer. II - Effects of Reynolds number and incidence

Part I of this paper presents airfoil heat transfer data obtained in a rotating turbine model at its design rotor incidence. This portion of the paper presents heat transfer data obtained in the same model for various combinations of Reynolds number and inlet turbulence and for a very wide range of rotor incidence. On the suction surfaces of the first stage airfoils the locations and lengths of transition were influenced by both the inlet turbulence level and the Reynolds number. In addition it was demonstrated that on the first stage pressure surfaces combinations of high Reynolds number and high turbulence can produce heat transfer rates well in excess of two-dimensional turbulent flow. Rotor heat transfer distributions indicate that for relatively small deviations from the design incidence, local changes to the heat transfer distributions were produced on both pressure and suction sides near the stagnation region. For extremely large negative incidence the flow was completely separated from the rotor pressure surface producing very high local heat transfer.

Blair, M. F.↗

Numerical and approximate solution of the high Reynolds number small separation problem

Several possible methods of solving the small separation problem at high Reynolds number are investigated. In addition to using analytical methods, there are several numerical approaches which are used. High Reynolds number laminar two dimensional problems are used for simplicity. A brief discussion is given of the finite difference methods since these methods are discussed in detail. Most of the emphasis is placed on developing an approximate integral method. As a model problem the supersonic compression ramp problem is chosen since several numerical solutions along with experimental data are available. The techniques discussed are modified and applied to other similar type wall geometries.

Davis, R. T.↗

Vacuum chamber pressure effects on thrust measurements of low Reynolds number nozzles

Tests were conducted to investigate the effect of vacuum facility pressure on the performance of small thruster nozzles. Thrust measurements of two converging-diverging nozzles with an area ratio of 140 and an orifice plate flowing unheated nitrogen and hydrogen were taken over a wide range of vacuum facility pressures and nozzle throat Reynolds numbers. In the Reynolds number range of 2200 to 12 000 there was no discernable viscous effect on thrust below an ambient to total pressure ratio of 1000. In nearly all cases, flow separation occurred at a pressure ratio of about 1000. This was the upper limit for obtaining an accurate thrust measurement for a conical nozzle with an area ratio of 140.

Sovey, J. S.↗

Vacuum chamber pressure effects on thrust measurements of low Reynolds number nozzles

Tests were conducted to investigate the effect of vacuum facility pressure on the performance of small thruster nozzles. Thrust measurements of two converging-diverging nozzles with an area ratio of 140 and an orifice plate flowing unheated nitrogen and hydrogen were taken over a wide range of vacuum facility pressures and nozzle throat Reynolds numbers. In the Reynolds number range of 2200 to 12,000 there was no discernable viscous effect on thrust below an ambient to total pressure ratio of 1000. In nearly all cases, flow separation occurred at a pressure ratio of about 1000. This was the upper limit for obtaining an accurate thrust measurement for a conical nozzle with an area ratio of 140.

Sovey, J. S.↗

Boundary-layer measurements on a high Reynolds number three-element airfoil

An experimental investigation is being conducted to evaluate the boundary layer associated with a two-dimensional three-element single-flap airfoil at high Reynolds numbers. The present measurements are being made in the Langley Low-Turbulence (centerline turbulence intensity level is 0.034 percent at a Mach number of 0.2 and a total pressure of 60 psia) Pressure Tunnel (LTPT). The LTPT is a closed-circuit wind tunnel with a test section which is 3 ft wide, 7.5 ft high, and 7.5 ft long. Operating total pressure for the LTPT varies from 10 atmospheres to near-vacuum conditions. Tests are being conducted at a Mach number of 0.2 and Reynolds numbers (based on chord length) of 5, 9, and 16 million. Measurements include boundary-layer velocity surveys at several chordwise locations and surface skin-friction measurements using Preston tubes.

Selby, Gregory V.↗