SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Technique has been developed for attaching and sealing tubes to header plates using a unique roll-forming tool. Technique is useful for attaching small tubes which are difficult to roll into conventional grooves in header plate tube holes, and for attaching when welding, brazing, or soldering is not desirable.
A set of generalized stability equations was developed for roller pairs in free rolling contact. A symmetric, dual contact model was used. Four possible external contact profiles that possess continuous contacting surfaces were studied. It was found that kinematic stability would be insured if the larger radius of transverse curvature, in absolute value, and the smaller rolling radius both exist on the roller that has the apex of its conical surface outboard of its main body. The stability criteria developed are considered to be useful for assessing axial restraint requirements for a variety of roller mechanisms and in the selection of roller contact geometry for traction drive devices.
Rolling-element fatigue tests were run with three synthetic lubricants with and without antiwear additives and with a paraffinic mineral oil at race temperatures of 336 to 353 K (146 146 to 175 F). The five-ball fatigue tester was used with steel balls to evaluate the relative fatigue lives with each of six lubricant-additive combinations. The tests were run at 5,520 MPa (800,000psi) maximum Hertz stress, 10,000 rpm shaft speed, and 30 deg contact angle. The lubricants tested have similar kinetic viscosities at 372 K (210 F) ranging from 0.034 to 0.089 sq cm/sec (3.4 to 8.9 cS). At these conditions, the mode of failure in the five-ball fatigue tester was classical subsurface rolling-element fatigue. The baseline for comparison of fatigue life was the paraffinic mineral oil without additives. The effects of the synthetic lubricants and their additives, which are useful for boundary lubrication, oxidation or foam inhibition, were evaluated.
Estimates of the effectiveness of a model following type control system in reducing the roll excursion due to a wake vortex encounter were obtained from single degree of freedom computations with inputs derived from the results of wind tunnel, flight, and simulation experiments. The analysis indicates that the control power commanded by the automatic system must be roughly equal to the vortex induced roll acceleration if effective limiting of the maximum bank angle is to be achieved.
A ferrographic analysis was used to determine the types and quantities of wear debris generated during accelerated rolling contact fatigue tests. The five-ball rolling contact fatigue tester was used. Ball specimens were made of a corrosion resistant, high-temperature bearing steel. The lubricant was a superrefined naphthenic mineral oil. Conditions included a maximum Hertz stress of 5.52 10 to the 9th power Pa and a shaft speed of 10,000 rpm. Four types of wear debris were observed: (1) normal rubbing wear particles, (2) fatigue microspall particles, (3) spheres, and (4) friction polymer deposits. The characterization of wear debris as a function of time was of limited use in predicting fatigue failures in these accelerated tests.
Rolling element fatigue studies were conducted with AISI M-50, EFR 18-4-1, and VAR 18-4-1. Groups of 12.7 mm (1/2-in) diameter balls of each material were tested in the five ball fatigue tester. Test conditions included a load of 1540 N (347 lbf) giving a maximum Hertz stress of 5520 MPa (800 000 psi), a shaft speed of 10,700 rpm, and a contact angle of 30 deg. Tests were run at a race temperature of 339 K (150 F) with a type 2 ester lubricant. The rolling element fatigue life of AISI M-50 was not significantly different from that of EFR 18-4-1 or VAR 18-4-1 based on a statistical comparison of the test results.
Mechanical rolling (a process used in industry for producing large quantities of metallic sheet and strip) has been suggested for the rapid low-cost manufacture of silicon sheet to be used for photovoltaic power generation equipment, such as solar arrays. The advantages of rolling include: high rates of production, wide sheets as products, good control of dimension, and (in the case of solar grade silicon) minimal development of impurities. Experiments have been performed using high-temperature, high-speed compression of polycrystalline silicon cylinders. Metallography and X-ray diffraction techniques have been used to examine the samples both before and after compression, and a model process has been designed to evaluate the technical practicality and economic feasibility of the method.
Ferrographic analysis was used to determine the types and quantities of wear particles generated during accelerated rolling contact fatigue tests. The NASA five-ball rolling contact fatigue tester was used. Ball specimens were made of AMS 5749, a corrosion-resistant high-temperature bearing steel. The lubricant was a super-refined naphthenic mineral oil. Conditions included a maximum Hertz stress of 5.52 billion Pa and a shaft speed of 10,000 rpm. Four types of wear particles were observed: normal rubbing wear particles, fatigue spall particles, spheres, and friction polymer.
The effects of random yawing and rolling velocities on passenger ride comfort responses were examined on a visual motion simulator. The effects of power spectral density shape and frequency ranges of peak power from 0 to 2 Hz were studied. The subjective rating data and the physical motion data obtained are presented. No attempt at interpretation or detailed analysis of the data is made. There existed during this study motions in all other degrees of freedom as well as the yawing and rolling motions, because of the characteristics of the simulator. These unwanted motions may have introduced some interactive effects on passenger responses which should be considered in any analysis of the data.
The lubrication of rolling element bearings is surveyed. Emphasis is on the critical design aspects related to speed, temperature, and ambient pressure environment. Types of lubrication including grease, jets, mist, wick, and through the race are discussed. The historical development, present state of technology, and the future problems of rolling element bearing lubrication are discussed.
The rolling cylinder phase change heat storage concept was developed to the point where a prototype design is completed and a cost analysis is prepared. A series of experimental and analytical tasks are defined to establish the thermal, mechanical, and materials behavior of rolling cylinder devices. These tasks include: analyses of internal and external heat transfer; performance and lifetime testing of the phase change materials; corrosion evaluation; development of a mathematical model; and design of a prototype and associated test equipment.
An oscillatory roll apparatus is described with which the complete set of moment and force derivatives due to an oscillation in roll can be obtained in a wind tunnel. A newly developed technique to reduce the dynamic data originating from the four-component balance used with the above apparatus is briefly presented. The technique is intended to account for the dynamic behavior of the model-balance subsystem in the presence of motions in the various degrees of freedom allowed by the balance webs. Finally, results obtained from both dynamic calibration as well as wind-tunnel tests are shown.
The test capabilities of the Stability Wind Tunnel of the Virginia Polytechnic Institute and State University are described, and calibrations for curved and rolling flow techniques are given. Oscillatory snaking tests to determine pure yawing derivatives are considered. Representative aerodynamic data obtained for a current fighter configuration using the curved and rolling flow techniques are presented. The application of dynamic derivatives obtained in such tests to the analysis of airplane motions in general, and to high angle of attack flight conditions in particular, is discussed.
The non-Newtonian constitutive equation of Winer and Bair (1979) is applied to a conventional isothermal film thickness analysis of line contact lubrication of rolling elements providing dimensionless film thickness equations for four lubrication methods. The equations can be applied to high viscosity and rolling speed and low limiting shear stress cases where Newtonian methods are not applicable. This analysis is based on a reasonable range of limiting shear stress which is smaller than the Newtonian values for low viscosity lubricants.
This paper is a broad survey of the lubrication of rolling-element bearings. Emphasis is on the critical design aspects related to speed, temperature, and ambient pressure environment. Types of lubrication including grease, jets, mist, wick, and through-the-race are discussed. The paper covers the historical development, present state of technology, and the future problems of rolling-element bearing lubrication.
An improved suspension system for an uncrowned wheel rolling on a flat track is presented. It is characterized by a wheel frame assembly including a wheel frame and at least one uncrowned wheel connected in supporting relation with the frame. It is adapted to be seated in rolling engagement with a flat track, a load supporting bed, and a plurality of flexural struts interconnecting the bed in supported relation with the frame. Each of said struts is disposed in a plane passing through the center of the uncrowned wheel surface along a line substantially bisecting the line of contact established between the wheel surface and the flat surface of the truck and characterized by a modulus of elasticity sufficient for maintaining the axis of rotation for the wheel in substantial parallelism with the line of contact established between the surfaces of the wheel and track.
Research on large-bore ball and roller bearings for aircraft engines is described. Tapered roller bearings and small-bore bearings are discussed. Temperature capabilities of rolling element bearings for aircraft engines have moved from 450 to 589 K (350 to 600 F) with increased reliability. High bearing speeds to 3 million DN can be achieved with a reliability exceeding that which was common in commercial aircraft. Capabilities of available bearing steels and lubricants were defined and established. Computer programs for the analysis and design of rolling element bearings were developed and experimentally verified. The reported work is a summary of NASA contributions to high performance engine and transmission bearing capabilities.
The lateral directional characteristics of an F-18 aircraft was investigated. Aerodynamic derivatives associated with pure roll rate, or the 'p' derivatives were obtained. The model is described and the procedures used to obtain and correct the data, and a graphical presentation of the results are presented. These results include graphs of the lateral directional static stability derivatives versus angle of attack, and the lateral directional force and moment coefficients versus nondimensional roll rate. Results are presented for several configurations including complete, complete without vertical tails, complete without horizontal tails, fuselage wing and fuselage alone. Each of these configuations was tested with and without wing leading edge extensions. The basic control surfaces were deflected and the results were investigated.