SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Digital avionics is continually expanding its role in communication (HF and VHF, satellite, data links), navigation (ground-based systems, inertial and satellite-based systems), and flight-by-wire control. Examples of electronic flight control system architecture, pitch, roll, and yaw control are presented. Modeling of complex hardware systems, electromagnetic interference, and software are discussed.
A satellite attitude control system is usable in the absence of any inertial yaw attitude reference, such as a gyroscope, and in the absence of a pitch bias momentum. Both the roll-yaw rigid body dynamics and the roll-yaw orbit kinematics are modelled. Pitch and roll attitude control are conventional. The model receives inputs from a roll sensor, and roll and yaw torques from reaction wheel monitors. The model produces estimated yaw which controls the spacecraft yaw attitude.
Equations of lifting entry are considered for fixed-angle-of-attack vehicular motion with path control for roll modulation of lift. Attention is directed to relocation and its consequences for the fixed-angle-of-attack atmospheric entry problem. Two reduced-order methods for working with the resulting system of equations are briefly examined. The methods are deemed to warrant further study.
A real-time multiple-function digital controller system was developed for the Active Flexible Wing (AFW) Program. The digital controller system (DCS) allowed simultaneous execution of two control laws: flutter suppression and either roll trim or a rolling maneuver load control. The DCS operated within, but independently of, a slower host operating system environment, at regulated speeds up to 200 Hz. It also coordinated the acquisition, storage, and transfer of data for near real-time controller performance evaluation and both open- and closed-loop plant estimation. It synchronized the operation of four different processing units, allowing flexibility in the number, form, functionality, and order of control laws, and variability in selection of sensors and actuators employed. Most importantly, the DCS allowed for the successful demonstration of active flutter suppression to conditions approximately 26 percent (in dynamic pressure) above the open-loop boundary in cases when the model was fixed in roll and up to 23 percent when it was free to roll. Aggressive roll maneuvers with load control were achieved above the flutter boundary.
A real time multiple-function digital controller system was developed for the Active Flexible Wing (AFW) Program. The digital controller system (DCS) allowed simultaneous execution of two control laws: flutter suppression and either roll trim or a rolling maneuver load control. The DCS operated within, but independently of, a slower host operating system environment, at regulated speeds up to 200 Hz. It also coordinated the acquisition, storage, and transfer of data for near real time controller performance evaluation and both open- and closed-loop plant estimation. It synchronized the operation of four different processing units, allowing flexibility in the number, form, functionality, and order of control laws, and variability in the selection of the sensors and actuators employed. Most importantly, the DCS allowed for the successful demonstration of active flutter suppression to conditions approximately 26 percent (in dynamic pressure) above the open-loop boundary in cases when the model was fixed in roll and up to 23 percent when it was free to roll. Aggressive roll maneuvers with load control were achieved above the flutter boundary. The purpose here is to present the development, validation, and wind tunnel testing of this multiple-function digital controller system.
The results of two successive experimental investigations of the effects of motion cues on manual control tracking tasks are reported. The first of these was an IFR single-axis VTOL roll attitude control task. Describing function data show the dominant motion feedback quantity to be angular velocity. The second experimental task was multiaxis, that of precision hovering of a VTOL using separated instrument displays with reduced motion amplitude scaling. Performance data and pilot opinion show angular position to be the dominant cue when simulator linear motion is absent.
The Langley Research Center uses radio-controlled, scaled aircraft models to study the spin-entry characteristics of aircraft. Recent spin-entry studies required the use of an electronic proportional-control system for manipulating model control surfaces. In order to meet control system requirements, a special-purpose analog computer was designed to simulate the coupling between roll and pitch controls. A digital encoder was designed to encode the voltage analogs of control-surface position into a special pulse format for transmission to the model. This paper describes the two special developments and their relationship to the functions of the overall control system.
Explore the source record for details and available documents.
Roll-ratchet refers to a high frequency oscillation which can occur in pilot-in-the-loop control of roll attitude in high performance aircraft. The frequencies of oscillation are typically well beyond those associated with the more familiar pilot-induced oscillation. A structural model of the human pilot which has been employed to provide a unified theory for aircraft handling qualities and pilot-induced oscillations is employed here to provide a theory for the existence of roll-ratchet. It is hypothesized and demonstrated using the structural model that the pilot's inappropriate use of vestibular acceleration feedback can cause this phenomenon, a possibility which has been discussed previously by other researchers. The possible influence of biodynamic feedback on roll ratchet is also discussed.
Piloted simulation studies of candidate control systems for VATOL aircraft were conducted on a six degree of freedom simulator. Hover and transitions from wing-born to hovering flight were performed, with and without turbulence, on a representative high performance fighter configuration. Deflection of the rear engine nozzle provided pitch and yaw control moments in concert with reaction controls for roll. Unique motion cues in hover result from the vertical displacement of the cockpit and the thrust vectoring nozzles. Abundant control power available with moderate engine nozzle deflection combined with rate feedback for stability augmentation provided very satisfactory control.
Aircraft flight characteristics at high angles of attack can be improved by controlling vortices shed from the nose. These characteristics have been investigated with the integration of the actuated nose strakes for enhanced rolling (ANSER) control system into the NASA F-18 High Alpha Research Vehicle. Several hardware and software systems were developed to enable performance of the research goals. A strake interface box was developed to perform actuator control and failure detection outside the flight control computer. A three-mode ANSER control law was developed and installed in the Research Flight Control System. The thrust-vectoring mode does not command the strakes. The strakes and thrust-vectoring mode uses a combination of thrust vectoring and strakes for lateral- directional control, and strake mode uses strakes only for lateral-directional control. The system was integrated and tested in the Dryden Flight Research Center (DFRC) simulation for testing before installation in the aircraft. Performance of the ANSER system was monitored in real time during the 89-flight ANSER flight test program in the DFRC Mission Control Center. One discrepancy resulted in a set of research data not being obtained. The experiment was otherwise considered a success with the majority of the research objectives being met.
Results are given of a series of systemic tests comparing lateral control devices with particular reference to their effectiveness at high angles of attack. These tests were made with two sizes of ordinary ailerons and different sizes of spoilers on a Clark Y wing model having a narrow auxiliary airfoil fixed ahead and above the leading edge, the chords of the main and auxiliary airfoils being parallel. In addition, the auxiliary airfoil itself was given angular deflection. The purpose was to provide rolling moments for lateral control. The tests were made in a 7 by 10 foot wind tunnel. They included both force and rotation tests to show the effect of the devices on the lift and drag characteristics of the wing and on the lateral stability characteristics, as well as lateral control. They showed that none of the aileron arrangements tried would give rolling control of an assumed satisfactory value at all angles of attack up to the stall. However, they would give satisfactory values, but at the expense of abnormally high deflections and very heavy hinge moments. The most effective combination of ailerons and spoilers gave satisfactory values of rolling moment at angles of attack below the stall, and the values did not fall off as rapidly above the stall as with ailerons alone. With an arrangement of this type having the proper relative proportions and linkage, it should be possible to obtain reasonably satisfactory yawing moments and control forces. Deflecting one-half of the auxiliary airfoil downward for the purpose of control gave strong favorable yawing moments at all angles of attack, but gave very small rolling moments at the low angles of attack.
Dynamic inversion is a technique for control law design in which feedback is used to simultaneously cancel system dynamics and achieve desired dynamic response characteristics. However, dynamic inversion control laws lack robustness to modeling errors if improperly designed. This paper examines a simple linear example, control of roll rate about the body axis of high performance aircraft, to illustrate some robustness problems which may occur with a simple dynamic inversion control law. The paper demonstrates how structured singular value synthesis techniques can be used to enhance the robustness properties of the dynamic inversion controller.
An experimental wind tunnel investigation has been made to determine the longitudinal and lateral aerodynamic stability and control characteristics of two tail fin arrangements of a monowing missile model. Both a conventional cruciform and a low profile tail arrangement were tested. The results indicate that the tail surfaces of both configurations were effective in producing pitch control. It was also concluded that both are effective in producing roll and yaw control that is accompanied by proverse yaw and roll, respectively. The conventional cruciform tail produces the most roll and yaw control.
A three-axis vehicle control study has been made by use of a fixed simulator and analog computing equipment, to evaluate the effects of various ways of utilizing rate information. A side-arm controller providing proportional acceleration control was used with a simulated vehicle having no inherent stability or damping. Vehicle rate signals were used to provide control feedback or system damping and were used in the instrument display either separate from or summed with displacement signals. Near optimum performance of both transitions in roll and control of system disturbance was obtained by using a combination of system damping and summed displacement signals and rate signals.
Review of a program for the development of advanced fluidic components and the application of these components to general aviation instrumentation and control. The major project in this category has been the development of a simple, reliable, two-axis autopilot for light aircraft, using a fluidic inertial rate sensor for stability and roll attitude control, and a simple magnetometer for azimuth reference. This autopilot has been succesfully flight-tested. Fluidic hardware developed for this autopilot is described, and projected improvements and extensions are discussed. Application of fluidic components to such flight instruments as turn coordinators, artificial horizons, and true airspeed indicators is explored.
The use of deterministic and regression methods to supplement the maximum likelihood estimation programs for the determination of the stability and control parameters of the Shuttle vehicle is discussed. Examples taken from STS-2 and STS-3 flight data show the use of deterministic methods to verify the effectiveness of the pitch and roll Reaction Control System (RCS), to verify the model structure used in the maximum likelihood estimator and to indicate regions of the descent trajectory where unmodeled moments dominate the vehicle motion and the application of maximum likelihood estimation would lead to incorrect parameter values. The use of regression methods to determine selected parameters when the more sophisticated maximum likelihood programs are not required, to determine the form of the vehicle mathematical model and to select the data time intervals for most effective parameter identification are also discussed.
A piloted simulation study investigating handling qualities and flight characteristics required for helicopter air to air combat is presented. The Helicopter Air Combat system was used to investigate this role for Army rotorcraft. Experimental variables were the maneuver envelope size (load factor and sideslip), directional axis handling qualities, and pitch and roll control-response type. Over 450 simulated, low altitude, one-on-one engagements were conducted. Results from the experiment indicate that a well damped directional response, low sideforce caused by sideslip, and some effective dihedral are all desirable for weapon system performance, good handling qualities, and low pilot workload. An angular rate command system was favored over the attitude type pitch and roll response for most applications, and an enhanced maneuver envelope size over that of current generation aircraft was found to be advantageous. Pilot technique, background, and experience are additional factors which had a significant effect on performance in the air combat tasks investigated. The implication of these results on design requirements for future helicopters is presented.