Results for “Radiative transfer modeling” — Page 16

DOE OSTI2021

Numerical analysis of particle dispersion and deposition in coal combustion using large-eddy simulation

High-fidelity modeling provides a useful approach to investigate the particle dispersion and deposition mechanism in pulverized coal combustion. To be able to analyze these detailed mechanisms, this work couples detailed multiphysics models for poly-dispersed turbulent, particle-laden flow, particle and gas phase reaction chemistry, convective, conductive and radiative heat transfer, ash formation and deposition with a Large-Eddy Simulation (LES) approach to numerically simulate coal combustion in a downfired self-sustained oxy-fuel combustor (OFC). It is necessary to explicitly capture all but the highest frequency dynamics of the turbulence and its coupling with each of the other physical phenomena using LES. Effects of subgrid-scale unresolved turbulence on the particle motions are also analyzed by a novel Stokes number analysis. Due to the inherent relation ship between coal combustion and ash deposition, this study integrates the improved ash deposition model into the numerical simulation. Overall simulation results are compared with experimentally measured data from the OFC. The simulation and measured data for the averaged gas temperature and deposition rates agree with 5% and 28%. This study shows that high-fidelity LES coupled with other detailed multiphysics models running on a exascale computing facility can provide a good representation of complex coal combustion and deposition in a laboratory-scale furnace.

multiphysics model↗

DOE OSTI2021

Comparative study with two reduced test facilities for air-cooled RCCS scaling law

Korea Atomic Energy Research Institute (KAERI) and Argonne National Laboratory (ANL) conducted steady-state tests at constant heat flux conditions to investigate the scale effect on heat removal behavior of the air-cooled Reactor Cavity Cooling System (RCCS). Two differently scaled-down test facilities were used in this study, KAERI’s ¼ scale with 4.0-m cavity height, and ANL’s ½ scale with 6.8-m cavity height. Two scaling laws were proposed to simulate the radiation across the cavity and the buoyancy-driven duct flow in the riser, respectively. The test matrix for KAERI and ANL test facilities focused on the scaling effect of the heated riser length with constant heat flux at the PMR200 RCCS design. The test results showed that mixed convection in the riser duct is an important factor for accurately extrapolating the thermo-fluid behavior in the prototype from the test results in the scale-down facilities. The system analysis code, GAMMA+, with improved heat transfer models predicted fairly well the air-cooled RCCS test data from two facilities. GAMMA+ analysis results showed that the predicted radiation fractions on the heated plate in the scale-down test conditions were larger than those on the reactor vessel in the prototype. The scaling law for air-cooled RCCS was improved by considering the mixed convection in the riser duct and the same radiation fraction on the heated plate. The mixed convection effect was calculated by the height ratio. The same radiation fraction provided a conservative extrapolation from the scale-down test results.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2019

Direct-drive double-shell implosion: A platform for burning-plasma physics studies

Double-shell ignition designs have been investigated with the indirect-drive inertial confinement fusion (ICF) scheme in both simulations and experiments in which the inner-shell kinetic energy was limited to ~10 to 15 kJ, even driven by megajoule-class lasers such as the National Ignition Facility. Since direct-drive ICF can couple more energy to the imploding shells, we have performed a detailed study on direct-drive double-shell (D 3 S) implosions with state-of-the-art physics models implemented in radiation-hydrodynamic codes (LILAC and DRACO), including nonlocal thermal transport, cross-beam energy transfer (CBET), and first-principles-based material properties. To mitigate classical unstable interfaces, we have proposed the use of a tungsten/beryllium–mixed inner shell with gradient-density layers that can be made by magnetron sputtering. In our D 3 S designs, a 70-μm-thick beryllium outer shell is driven symmetrically by a high-adiabat (α ≥ 10), 1.9-MJ laser pulse to a peak velocity of ~240 km/s. Upon spherical impact, the outer shell transfers ~30 to 40 kJ of kinetic energy to the inner shell filled with deuterium–tritium gas or liquid, giving neutron-yield energies of ~6 MJ in 1-D simulations. Two-dimensional high-mode DRACO simulations indicated that such high-adiabat D 3 S implosions are not susceptible to laser imprint, but the long-wavelength perturbations from the laser port configuration along with CBET can be detrimental to the target performance. Yet, neutron yields of ~0.3- to 1.0-MJ energies can still be obtained from our high-mode DRACO simulations. The robust α-particle bootstrap is readily reached, which could provide a viable platform for burning-plasma physics studies. Once CBET mitigation and/or more laser energy becomes available, we believe that breakeven or moderate energy gain might be feasible with the proposed D 3 S scheme.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Lower limits for non-radiative recombination loss in organic donor/acceptor complexes

Understanding the factors controlling radiative and non-radiative transition rates for charge transfer states in organic systems is important for applications ranging from organic photovoltaics (OPV) to lasers and LEDs. Here we explore the role of charge-transfer (CT) energetics, lifetimes, and photovoltaic properties in the limit of very slow non-radiative rates by using a model donor/acceptor system with photoluminescence dominated by thermally activated delayed fluorescence (TADF). This blend exhibits an extremely high photoluminescence quantum efficiency (PLQY = ~22%) and comparatively long PL lifetime, while simultaneously yielding appreciable amounts of free charge generation (photocurrent external quantum efficiency EQE of 24%). In solar cells, this blend exhibits non-radiative voltage losses of only ~0.1 V, among the lowest reported for an organic system. Notably, we find that the non-radiative decay rate, k nr , is on the order of 10 5 s -1 , approximately 4–5 orders of magnitude slower than typical OPV blends, thereby confirming that high radiative efficiency and low non-radiative voltage losses are achievable by reducing k nr . Furthermore, despite the high radiative efficiency and already comparatively slow k nr , we find that k nr is nevertheless much faster than predicted by Marcus–Levich–Jortner two-state theory and we conclude that CT-local exciton (LE) hybridization is present. Our findings highlight that it is crucial to evaluate how radiative and non-radiative rates of the LE states individually influence the PLQY of charge-transfer states, rather than solely focusing on the PLQY of the LE. This conclusion will guide material selection in achieving low non-radiative voltage loss in organic solar cells and high luminescence efficiency in organic LEDs.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Direct Measurement of the Selective Microwave-Induced Heating of Agglomerates of Dipolar Molecules: The Origin of and Parameters Controlling a Microwave Specific Superheating Effect

Agglomerates of polar molecules in nonpolar solvents are selectively heated by microwave radiation. The magnitude of the selective heating was directly measured by using the temperature dependence of the intensities of the Stokes and anti-Stokes bands in the Raman spectra of p-nitroanisole (pNA) and mesitylene. Under dynamic heating conditions, a large apparent temperature difference (ΔT) of over 100 °C was observed between the polar pNA solute and the nonpolar mesitylene solvent. This represents the first direct measurement of the selective microwave heating process. The magnitude of the selective microwave heating was affected by the properties of the agglomerated pNA. As the concentration of the pNA increases, the magnitude of the selective heating of the pNA was observed to decrease. This is explained by the tendency of the pNA dipoles to orient in an antiparallel fashion in the aggregates as measured by the Kirkwood g value, which decreased with increasing concentration. This effect reduces the net dipole moment of the agglomerates, which decreases the microwave absorption. After the radiation was terminated, the effective temperature of the dipolar molecules returned slowly to that of the medium. The slow heat transfer was modeled successfully by treating the solutions as a biphasic solvent/solute system. Based on modeling and the fact that the agglomerate can be heated above the boiling temperature of the solvent, an insulating layer of solvent vapor is suggested to form around the heated agglomerate, slowing convective heat transfer out of the agglomerate. Furthermore, this is an effect unique to microwave heating.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

A Model for Radiolysis in a Flowing-Water Target during High-Intensity Proton Irradiation

At the Facility for Rare Isotope Beams (FRIB), interactions between heavy-ion beams and beam-dump water will create a wide variety of radionuclides which can be accessed by a technique known as “isotope harvesting”. However, irradiation of water is always accompanied by the creation of numerous radical, ionic, and molecular radiolysis products. Some of the radiolysis products have sufficiently long lifetimes to accumulate in the irradiated water and affect the harvesting chemistry. Here we investigate the formation of hydrogen peroxide, molecular hydrogen, and molecular oxygen during a high-intensity proton irradiation of a flowing-water isotope-harvesting target and compare the experimental results to simulations. The simulations kinetically model the chemical reactions occurring in the homogeneous phase of radiolysis in flowing water and establish an “effective yield”. In both the experiment and simulations, the bulk quantities of H 2 , H 2 O 2 , and O 2 are considerably lower than predicted by primary radiolysis yields (escape yields), meaning that in the high beam intensity regime the homogeneous phase reactions have a considerable impact on the overall chemical composition of the water. Further, it could be shown that for radiation which is characterized by a limited linear energy transfer, such as the here applied protons, the bulk outcome of the microscopic kinetic modeling could be estimated by a simplified steady-state model.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Preliminary neutronic and thermal analysis of Inertial Fusion Energy systems with a focus on thick liquid wall concepts

This paper provides an assessment of the neutronic behavior of Inertial Fusion Energy systems using the Serpent 2 Monte Carlo code. The study explores different types of reactor concepts, including dry-wall and thick liquid wall systems. In particular, it characterizes the tritium breeding and energy multiplication performance, as well as the effect of long-term irradiation on structural materials. For this purpose, the displacement per atom (DPA) and the gas production rate in structural materials are calculated. A simplified geometry with varying geometrical parameters is used as a representation for the different kinds of devices. Additionally, the case of the HYLIFE-II concept is used to assess modeling inaccuracies arising from certain approximations. A comparison between the simplified geometry and a realistic one is performed, thanks to Serpent’s capability to run transport calculations on unstructured meshes. The study then addresses the impact of these discrepancies on the temperature distribution in the first wall using the GeN-Foam code for conjugate heat transfer analysis. The results highlight the necessity to consider the heterogeneous nature of the liquid wall, as simplified models tend to underestimate radiation damage metrics and heat loads.

Conjugate heat transfer↗

DOE OSTI2020

In situ temperature profile measurements with high-energy X-rays as a probe of optical floating zone crystal growth environment

The ability of optical floating zone (OFZ) furnaces to rapidly produce large single crystals of complex emerging materials has had a transformative effect on many scientific fields that require samples of this type. However, the crystal growth process within the OFZ furnace is not well understood owing to the challenges involved in monitoring the high-temperature crystal growth process. Novel beamline-compatible optical furnaces that approximate the inhomogeneous growth environment within an OFZ furnace have been fabricated and tested in high-energy synchrotron beamlines. In this paper, it is demonstrated that temperature profiles can be effectively extracted from powder diffraction data collected on polycrystalline ceramic rods heated at their tip. Furthermore, these measured temperature profiles can be accurately reproduced using a heat-transfer model that accounts for solid-state thermal conduction, partial sample lamp power absorption, convective air cooling and radiative cooling, allowing key thermal parameters such as thermal conductivity to be extracted from experimental data.

36 MATERIALS SCIENCE↗

DOE OSTI2024

SIERRA Low Mach Module: Fuego Verification Manual (V.5.20)

The SIERRA Low Mach Module: Fuego, henceforth referred to as Fuego, is the key element of the ASC fire environment simulation project. The fire environment simulation project is directed at characterizing both open large-scale pool fires and building enclosure fires. Fuego represents the turbulent, buoyantly-driven incompressible flow, heat transfer, mass transfer, combustion, soot, and absorption coefficient model portion of the simulation software. Sierra/PMR handles the participating-media thermal radiation mechanics. This project is an integral part of the SIERRA multi-mechanics software development project. Fuego depends heavily upon the core architecture developments provided by SIERRA for massively parallel computing, solution adaptivity, and mechanics coupling on unstructured grids.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2024

SIERRA Low Mach Module: Fuego Verification Manual (V.5.22)

The SIERRA Low Mach Module: Fuego, henceforth referred to as Fuego, is the key element of the ASC fire environment simulation project. The fire environment simulation project is directed at characterizing both open large-scale pool fires and building enclosure fires. Fuego represents the turbulent, buoyantly-driven incompressible flow, heat transfer, mass transfer, combustion, soot, and absorption coefficient model portion of the simulation software. Sierra/PMR handles the participating-media thermal radiation mechanics. This project is an integral part of the SIERRA multi-mechanics software development project. Fuego depends heavily upon the core architecture developments provided by SIERRA for massively parallel computing, solution adaptivity, and mechanics coupling on unstructured grids.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2025

SIERRA Low Mach Module: Fuego Verification Manual - Version 5.24

The SIERRA Low Mach Module: Fuego, henceforth referred to as Fuego, is the key element of the ASC fire environment simulation project. The fire environment simulation project is directed at characterizing both open large-scale pool fires and building enclosure fires. Fuego represents the turbulent, buoyantly-driven incompressible flow, heat transfer, mass transfer, combustion, soot, and absorption coefficient model portion of the simulation software. Sierra/PMR handles the participating-media thermal radiation mechanics. This project is an integral part of the SIERRA multi-mechanics software development project. Fuego depends heavily upon the core architecture developments provided by SIERRA for massively parallel computing, solution adaptivity, and mechanics coupling on unstructured grids.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2025

SIERRA Low Mach Module: Fuego Verification Manual (V.5.26)

The SIERRA Low Mach Module: Fuego, henceforth referred to as Fuego, is the key element of the ASC fire environment simulation project. The fire environment simulation project is directed at characterizing both open large-scale pool fires and building enclosure fires. Fuego represents the turbulent, buoyantly-driven incompressible flow, heat transfer, mass transfer, combustion, soot, and absorption coefficient model portion of the simulation software. Sierra/PMR handles the participating-media thermal radiation mechanics. This project is an integral part of the SIERRA multi-mechanics software development project. Fuego depends heavily upon the core architecture developments provided by SIERRA for massively parallel computing, solution adaptivity, and mechanics coupling on unstructured grids.

42 ENGINEERING↗

DOE OSTI2026

SIERRA Low Mach Module: Fuego Verification Manual - Version 5.28

The SIERRA Low Mach Module: Fuego, henceforth referred to as Fuego, is the key element of the ASC fire environment simulation project. The fire environment simulation project is directed at characterizing both open large-scale pool fires and building enclosure fires. Fuego represents the turbulent, buoyantly-driven incompressible flow, heat transfer, mass transfer, combustion, soot, and absorption coefficient model portion of the simulation software. Sierra/PMR handles the participating-media thermal radiation mechanics. This project is an integral part of the SIERRA multi-mechanics software development project. Fuego depends heavily upon the core architecture developments provided by SIERRA for massively parallel computing, solution adaptivity, and mechanics coupling on unstructured grids.

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗

DOE OSTI2026

SIERRA Low Mach Module: Fuego Verification Manual - Version 5.30

The SIERRA Low Mach Module: Fuego, henceforth referred to as Fuego, is the key element of the ASC fire environment simulation project. The fire environment simulation project is directed at characterizing both open large-scale pool fires and building enclosure fires. Fuego represents the turbulent, buoyantly-driven incompressible flow, heat transfer, mass transfer, combustion, soot, and absorption coefficient model portion of the simulation software. Sierra/PMR handles the participating-media thermal radiation mechanics. This project is an integral part of the SIERRA multi-mechanics software development project. Fuego depends heavily upon the core architecture developments provided by SIERRA for massively parallel computing, solution adaptivity, and mechanics coupling on unstructured grids.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2023

Contribution of nuclear excitation electromagnetic form factors in C 12 and O 16 to the Coulomb sum rule

We report on empirical parametrizations of longitudinal and transverse nuclear excitation electromagnetic form factors in 12 C and 16 O. We extract the contribution of nuclear excitations to the normalized inelastic Coulomb sum rule [S L (q)] as a function of momentum transfer q and find that it is significant (0.29 ± 0.030 at q = 0.22 GeV). The total contributions of nuclear excitations to S L (q) in 12 C and 16 O are found to be equal within uncertainties. Since the cross sections for nuclear excitations are significant, the radiative tails from nuclear excitations should be included in precise calculations of radiative corrections to quasielastic electron scattering at low q and deep-inelastic electron scattering at large energy transfers ν. The parametrizations also serve as a benchmark in testing theoretical modeling of cross sections for excitation of nuclear states in electron and neutrino interactions on nuclear targets at low energies.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2020

Development of the finite slab geometry in the NORA code

In this work we develop the complete linearization formalism for the radiation transfer equation in slab geometry. This development was motivated by an observed convergence instability arising from the NORA code’s inner boundary while modeling a suite of simple test problems in slab geometry presented at the Line Transfer Workshop held in LLNL in May of 2019. The convergence issue was seen to emerge early on in Newton-Raphson iterations. These test problems required parameters in the former NORA inner boundary to achieve the asymptotic limit of zero incoming intensity. In this work we derive the limiting case directly to gain insight into the former algorithm’s pathology.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2021

The Anatomy of an Unusual Edge-on Protoplanetary Disk. I. Dust Settling in a Cold Disk

As the earliest stage of planet formation, massive, optically thick, and gas-rich protoplanetary disks provide key insights into the physics of star and planet formation. When viewed edge-on, high-resolution images offer a unique opportunity to study both the radial and vertical structures of these disks and relate this to vertical settling, radial drift, grain growth, and changes in the midplane temperatures. In this work, we present multi-epoch Hubble Space Telescope and Keck scattered light images, and an Atacama Large Millimeter/submillimeter Array 1.3 mm continuum map for the remarkably flat edge-on protoplanetary disk SSTC2DJ163131.2–242627, a young solar-type star in ρ Ophiuchus. We model the 0.8 μm and 1.3 mm images in separate Markov Chain Monte Carlo (MCMC) runs to investigate the geometry and dust properties of the disk using the MCFOST radiative transfer code. In scattered light, we are sensitive to the smaller dust grains in the surface layers of the disk, while the submillimeter dust continuum observations probe larger grains closer to the disk midplane. An MCMC run combining both data sets using a covariance-based log-likelihood estimation was marginally successful, implying insufficient complexity in our disk model. The disk is well characterized by a flared disk model with an exponentially tapered outer edge viewed nearly edge-on, though some degree of dust settling is required to reproduce the vertically thin profile and lack of apparent flaring. A colder than expected disk midplane, evidence for dust settling, and residual radial substructures all point to a more complex radial density profile to be probed with future, higher-resolution observations.

47 OTHER INSTRUMENTATION↗

DOE OSTI2024

A RELAP5-3D Model of the Lobo Lead Loop

The goal of our research is to build upon the capability of RELAP5-3D to model molten lead systems. Molten lead has several potential uses in future advanced reactors like the lead fast reactor or fusion reactors that utilize dual-coolant lead lithium blankets. This potential for use in future generations of reactors highlights the necessity to develop molten lead models to ensure that they can accurately predict the thermohydraulic behavior. We have developed a RELAP5-3D model of the Lobo Lead Loop facility, located at the University of New Mexico, to verify the accuracy of RELAP5-3D via comparison to existing computational fluid dynamics results and analytical calculations. It was found that RELAP5-3D accurately calculated radiative heat transfer (within < 1%) when compared to theoretical calculations. In addition, pressure drop calculations done in RELAP5-3D demonstrated reasonable agreement within 20 kPa, mostly within ~7-15%, when compared to the computational fluid dynamics model of the facility developed by the University of New Mexico, and captured the dependence of pressure drop on flow velocity accurately. Finally, a hypothetical loss of flow transient was imposed on the RELAP5-3D model to determine the feasibility of performing a similar experiment with the Lobo Lead Loop. It was found that such an experiment could be possible as the RELAP5-3D model indicated that the temperatures of the fluid would not exceed limiting temperatures of the structure (1658 K) nor the maximum temperature of the electromagnetic pump inlet (823 K). Although there is not experimental data to begin validation, the model will be readily available for future validation studies when the experimental data is generated, especially as the model continues to evolve over time. Furthermore, the results so far demonstrate a promising first step in the verification/validation of the RELAP5-3D model of the Lobo Lead Loop.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗