SEARCH · Search NASA

Results for “Reaction mechanisms”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

All sources NASA NTRS DOE OSTI

NASA NTRS1991

Processing and properties of SiC whisker- and particulate-reinforced reaction bonded Si3N4

The microstructure and mechanical properties of reaction bonded Si3N4 (RBSN) reinforced with SiC whiskers of particles were investigated using RBSN composites made from colloidally pressed octanol dispersions of high-purity Si powders mixed with either SiC whiskers or alpha-SiC particles. Results of investigations, revealing high conversions of Si to Si3N4, specific surface areas, and constant relative densities and strengths, showed that the uniform microstructure and small flaw size of the matrix were maintained in the composites and that no degradation of the reinforcements was taking place. Neither the monolithic nor the composite materials exhibited R-curve behavior. A modest increase in fracture toughness was observed only in the RBSN containing 33 vol pct SiC(p).

Lightfoot, A.↗

NASA NTRS1991

Investigation of the effect of thermal exposure on the mechanical properties of titanium/SiC composites

The objective was to evaluate the influence of thermal exposure, both isothermal and cyclic, on the reaction kinetics, mechanical properties and fracture behavior of Ti-1100 alloy/SiC fiber composites. Previously, it was determined that composites made with TiB2 coated SiC fiber (sigma) reacted at the same rate as SCS-6 fibers. As a result, the thinner surface coating on the Sigma fiber was completely consumed at shorter times than that on the SCS-6. Thermal cycling experiments were conducted on longitudinal and transverse Ti-1100/SCS-6 composites over a temperature range of 150 to 800 C for 500 cycles. The thermal exposures were carried out in air and argon. No appreciable tensile strength degradation was observed for samples cycled in argon, although a strength loss was noted for the samples cycled in air. Fracture surfaces characterization showed brittle matrix failure in regions near the surface and in regions where there was a path for O2 ingress.

Gundel, Douglas B.↗

NASA NTRS1985

Mechanical properties of SiC fiber-reinforced reaction-bonded Si3N4 composites

The room temperature mechanical and physical properties of silicon carbide fiber reinforced reaction-bonded silicon nitride composites (SiC/RBSN) have been evaluated. The composites contained 23 and 40 volume fraction of aligned 140 micro m diameter chemically vapor deposited SiC fibers. Preliminary results for composite tensile and bend strengths and fracture strain indicate that the composites displayed excellent properties when compared with unreinforced RBSN of comparable porosity. Fiber volume fraction showed little influence on matrix first cracking strain but did influence the stressed required for matrix first cracking and for ultimate composite fracture strength. It is suggested that by reducing matrix porosity and by increasing the volume fraction of the large diameter SiC fiber, it should be possible to further improve the composite stress at which the matrix first cracks.

Bhatt, R. T.↗

NASA NTRS1986

Mechanical properties of SiC fiber-reinforced reaction-bonded Si3N4 composites

Bhatt, Ramakrishna T.↗

NASA NTRS1986

The evolution of nucleotides

Examples of chiral selection in nonenzymatic aminoacylation of internal 2-prime hydroxyl groups of oligo- and polynucleotides are discussed as an evidence for the early evolution of bionucleotides. Some factors that could influence the degree of this chiral selection and its direction are discussed. These include the structure of the aminoacyl component, the structure of the nucleoside component, and the reaction conditions. Investigation of the mechanism of this reaction was aided by the use of 3-prime inosine methyl phosphate (as a simplified model for a dinucleoside monophosphate) and proton NMR spectroscopy of t-butoxycarbonyl-alanyl esters of nucleosides as models for the transition state of the aminoacylation reaction itself.

Usher, D. A.↗

NASA NTRS2024

Mechanisms of Apatite Formation in Reactions of Yb 2-2x Gd 2x Si 2 O 7 with CMAS

Bulk β-Yb 1.9 Gd 0.1 Si 2 O 7 , β-Yb 1.6 Gd 0.4 Si 2 O 7 , and γ-Yb 1.4 Gd 0.6 Si 2 O 7 , along with baseline γ-Y 2 Si 2 O 7 and β-Yb 2 Si 2 O 7 were investigated in contact with a molten silicate to determine mechanisms of thermochemical degradation. A model 30.67CaO-8.25MgO-12.81AlO 1.5- 48.27SiO 2 silicate composition was deposited on the surfaces of the samples at a loading of ~2 mg/cm 2 . Reactions with the molten silicate resulted in the formation of a silicate apatite layer, which has been shown to reduce further molten silicate infiltration. Additions of gadolinium up to 30 mol% to Yb 2 Si 2 O 7 reduced infiltration up to ~60% compared to baseline Yb 2 Si 2 O 7 , but additional exposure time at temperature resulted in loss of the apatite layer. The results herein indicate that doping with gadolinium disilicate may not be beneficial in the long term degradation of disilicate-based EBCs by molten silicates.

Jamesa L. Stokes↗

NASA NTRS1979

Experimental and theoretical examples of the value and limitations of transition state theory

Value and limitations of transition-state theory (TST) are reviewed. TST analyses of the temperature dependence of the 'direct' reactions CH3 + CH3CHO yields CH4 + CH3CO(1) and O + CH4 yields OH + CH3(2) are presented in detail, and other examples of TST usefulness are recalled. Limitations are discussed for bimolecular processes in terms of 'complex' vs. 'direct' mechanisms. The reaction OH + CO yields CO2 + H is discussed in this context. Limitations for unimolecular processes seem to arise only for simple bond fission processes, and recent advances are noted.

Golden, D. M.↗

NASA NTRS1982

On the use of a global hydrogen-air combustion model in the calculation of turbulent reacting flows

A two-step global model describing the combustion of hydrogen in air at one atmosphere pressure is developed by comparing the temperature histories obtained from a 28-reaction H-O mechanism. Using criteria discussed herein, good agreement is obtained in the range of initial mixture temperatures from 1000K to 2000K and in the range of equivalence ratios from 0.2 to 2.0. The two-step global model is compared with the results obtained using an eight-step, H-O reaction mechanism in a computer program describing the turbulent diffusion of hydrogen in supersonic, axisymmetric and two-dimensional reacting flows. Comparisons of profiles of temperature, fuel mass flux, and pitot pressure are presented. The global model is judged to be adequate in flows which are not dominated by long ignition delay times.

Rogers, R. C.↗

NASA NTRS1985

Theoretical studies of the ignition and combustion of silane-hydrogen-air mixtures

A chemical kinetic mechanism is proposed for the combustion of silane-hydrogen-oxygen-nitrogen mixtures in the initial temperature range from 800K to 1250K and pressure range from 0.5 to 1.35 atm. The mechanism yields results which are in agreement with published ignition delay times obtained from shock tube experiments. Comparisons between the results obtained using the proposed mechanism and that of an alternative mechanism reveal that the former predicts appreciably shorter ignition delay times, but a flame blowout envelope which is shifted so as to decrease the stable flame region. Over much of the thermodynamic range examined, the mechanism predicts long reaction times. A three step global mechanism is proposed which closely models the ignition phase of SiH4 - H2 - air combustion; however, the reaction phase is less well reproduced by the global model. The necessity for additional experimental data to further assess the proposed models is stressed.

Chinitz, W.↗

NASA NTRS1989

Oxidation effects on the mechanical properties of SiC fiber-reinforced reaction-bonded silicon nitride matrix composites

The room temperature mechanical properties of SiC fiber reinforced reaction bonded silicon nitride composites were measured after 100 hrs exposure at temperatures to 1400 C in nitrogen and oxygen environments. The composites consisted of approx. 30 vol percent uniaxially aligned 142 micron diameter SiC fibers in a reaction bonded Si3N4 matrix. The results indicate that composites heat treated in a nitrogen environment at temperatures to 1400 C showed deformation and fracture behavior equivalent to that of the as-fabricated composites. Also, the composites heat treated in an oxidizing environment beyond 400 C yielded significantly lower tensile strength values. Specifically in the temperature range from 600 to 1000 C, composites retained approx. 40 percent of their as-fabricated strength, and those heat treated in the temperatures from 1200 to 1400 C retained 70 percent. Nonetheless, for all oxygen heat treatment conditions, composite specimens displayed strain capability beyond the matrix fracture stress; a typical behavior of a tough composite.

Bhatt, Ramakrishna T.↗

NASA NTRS1985

Shock tube measurements of growth constants in the branched-chain ethane-carbon monoxide-oxygen system

Exponential free radical growth constants have been measured for ethane carbon monoxide oxygen mixtures by monitoring the growth of oxygen atom concentration as manifested by CO flame band emission. Data were obtained over the temperature range of 1200 to 1700 K. The data were analyzed using an ethane oxidation mechanism involving seven elementary reaction steps. Calculated growth constants were close to experimental values at lower temperatures, up to about 1400 K, but at higher temperatures computed growth constants were considerably smaller than experiment. In attempts to explain these results additional branching reactions were added to the mechanism. However, these additional reactions did not appreciably change calculated growth constants.

Brokaw, R. S.↗

NASA NTRS1996

A new methodology to determine kinetic parameters for one- and two-step chemical models

In this paper, a new methodology to determine kinetic parameters for simple chemical models and simple transport properties classically used in DNS of premixed combustion is presented. First, a one-dimensional code is utilized to performed steady unstrained laminar methane-air flame in order to verify intrinsic features of laminar flames such as burning velocity and temperature and concentration profiles. Second, the flame response to steady and unsteady strain in the opposed jet configuration is numerically investigated. It appears that for a well determined set of parameters, one- and two-step mechanisms reproduce the extinction limit of a laminar flame submitted to a steady strain. Computations with the GRI-mech mechanism (177 reactions, 39 species) and multicomponent transport properties are used to validate these simplified models. A sensitivity analysis of the preferential diffusion of heat and reactants when the Lewis number is close to unity indicates that the response of the flame to an oscillating strain is very sensitive to this number. As an application of this methodology, the interaction between a two-dimensional vortex pair and a premixed laminar flame is performed by Direct Numerical Simulation (DNS) using the one- and two-step mechanisms. Comparison with the experimental results of Samaniego et al. (1994) shows a significant improvement in the description of the interaction when the two-step model is used.

Mantel, T.↗

NASA NTRS1981

Irradiation of NH3-CH4 mixtures as a model of photochemical processes in the Jovian planets and Titan

The reactions occurring upon the ultraviolet irradiation of ammonia-methane mixtures are investigated in a simulation of the atmospheric chemistry of the Jovian planets and Titan. Gas mixtures were irradiated at 185 nm at temperatures from 156-298 K, and product and reactant concentrations were determined by means of gas chromatography. The ratio of the moles of CH4 lost per mole of NH3 decomposed is found to be 0.25, with the extent of CH4 decomposition independent of temperature. The absence of a temperature effect suggests that nonthermal atoms, probably hydrogen, initiate CH4 decomposition by the extraction of a hydrogen atom. A decrease in CH4 loss with increasing pressure or the addition of other gases to the photolysis mixture, and the lack of an increase in NH3 photolysis with CH4 pressure support this mechanism. Major reaction products obtained include C2H2, C3H8 or CH3NH2, and C4H10. Considerations of atmospheric concentrations of H2 and He indicate that NH3 photolysis does not contribute to CH4 decomposition on Jupiter, Saturn, Uranus, and Neptune, although it may have had a role in the formation of the Titan atmosphere.

Ferris, J. P.↗

NASA NTRS1972

Popping phenomena with the hydrazine nitrogen-tetroxide propellant system.

The propellant spray resulting from the impingement of liquid jets of hydrazine and nitrogen tetroxide has been studied at atmospheric pressure by means of streak photography. The streak photographs show periodic small explosions that originate near the impingement point and propagate through the propellant spray at velocities of 3000 to 5000 fps, consuming all propellant droplets over a distance of up to 6 in. Typical streak photographs are presented. The frequency of the explosions or pops ranged up to several hundred cps, and could be controlled by varying the contact time in the liquid phase. Below a minimum threshold contact time, popping did not take place. At high values of contact time, the popping rate was controlled by the transit time of the free jet before impingement. Flashing of the oxidizer prior to impingement prevented popping under certain conditions. It is postulated that popping is initiated by liquid phase reactions. A mechanism for the occurrence of popping and its relation to reactive stream separation is suggested.

Houseman, J.↗

NASA NTRS1973

Forced guidance and distribution of practice in sequential information processing.

Distribution of practice and forced guidance were used in a sequential information-processing task in an attempt to increase the capacity of human information-processing mechanisms. A reaction time index of the psychological refractory period was used as the response measure. Massing of practice lengthened response times while forced guidance shortened them. Interpretation was in terms of load reduction upon the response-selection stage of the information-processing system.-

Decker, L. R.↗

NASA NTRS1978

Solubility, stability, and electrochemical studies of sulfur-sulfide solutions in organic solvents

A preliminary study of the sulfur electrode in organic solvents suggests that the system warrants further investigation for use in a low temperature (100 deg to 120 C) Na-S secondary battery. A qualitative screening was undertaken at 120 C to determine the solubilities and stabilities of Na2S and Na2S2 in representatives of many classes of organic solvents. From the screening and quantitative studies, two classes of solvents were selected for work; amides and cyclic polyalcohols. Voltammetric and Na-S cell charge discharge studies of sulfide solutions in organic solvents (e.g., N, N-dimethylformamide) at 120 C suggested that the reversibilities of the reactions on Pt or high density graphite were moderately poor. However, the sulfur electrode was indeed reducible (and oxidizable) through the range of elemental sulfur to Na2S. Reactions and mechanisms are proposed for the oxidation reduction processes occurring at the sulfur electrode.

Fielder, W. L.↗

NASA NTRS1979

An analytical study of nitrogen oxides and carbon monoxide emissions in hydrocarbon combustion with added nitrogen, preliminary results

The effect of combustor operating conditions on the conversion of fuel-bound nitrogen (FBN) to nitrogen oxides NO sub x was analytically determined. The effect of FBN and of operating conditions on carbon monoxide (CO) formation was also studied. For these computations, the combustor was assumed to be a two stage, adiabatic, perfectly-stirred reactor. Propane-air was used as the combustible mixture and fuel-bound nitrogen was simulated by adding nitrogen atoms to the mixture. The oxidation of propane and formation of NO sub x and CO were modeled by a fifty-seven reaction chemical mechanism. The results for NO sub x and CO formation are given as functions of primary and secondary stage equivalence ratios and residence times.

Bittker, D. A.↗

NASA NTRS1980

High electrical resistivity carbon/graphite fibers

Carbon/graphite fibers were chemically oxidized in the liquid phase to fibers of graphite oxide. Resistivity increases as high as 10,000 times were obtained, the oxidized fiber decomposed on exposure to atmosphere. A factor of 1,000 remained as a stable increment. The largest change observed was 1,000,000 times. Best results were obtained on the most highly graphitized fibers. Electrochemical oxidation yielded a lower increase--about 10 times, but provided a controllable method of synthesis and insight to the mechanism of reaction. Tensile tests indicated that the strength of the fiber on oxidation was decreased by no more than 25 percent.

Vogel, F. L.↗