The effect of surface reactions on the solid propellant response function.
Surface coupled heat release effect on oscillatory amplitude of pressure coupled response in solid propellant
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Surface coupled heat release effect on oscillatory amplitude of pressure coupled response in solid propellant
Development of advanced differential absorption lidar (DIAL) receivers is very important to increase the accuracy of atmospheric water vapor measurements. A major component of such receivers is the optical detector. In the near-infrared wavelength range avalanche photodiodes (APD's) are the best choice for higher signal-to-noise ratio, where there are many water vapor absorption lines. In this study, characterization experiments were performed to evaluate a group of silicon-based APD's. The APD's have different structures representative of different manufacturers. The experiments include setups to calibrate these devices, as well as characterization of the effects of voltage bias and temperature on the responsivity, surface scans, noise measurements, and frequency response measurements. For each experiment, the setup, procedure, data analysis, and results are given and discussed. This research was done to choose a suitable APD detector for the development of an advanced atmospheric water vapor differential absorption lidar detection system operating either at 720, 820, or 940 nm. The results point out the benefits of using the super low ionization ratio (SLIK) structure APD for its lower noise-equivalent power, which was found to be on the order of 2 to 4 fW/Hz(sup (1/2)), with an appropriate optical system and electronics. The water vapor detection systems signal-to-noise ratio will increase by a factor of 10.
Investigation of surface Rayleigh wave response with simulated defects
Surface coupled heat release effect on oscillatory amplitude of pressure coupled response in solid propellant
While it is reasonable to predict that photosynthetic rates are inhibited while leaves are wet, leaf gas exchange measurements during wet conditions are challenging to obtain due to equipment limitations and the complexity of canopy-atmosphere interactions in forested environments. Thus, the objective of this study was to evaluate responses of seven tropical and three semiarid savanna plant species to simulated leaf wetness and test the hypotheses that (i) leaf wetness reduces photosynthetic rates (Anet), (ii) leaf traits explain different responses among species and (iii) leaves from wet environments are better adapted for wet leaf conditions than those from drier environments. The two sites were a tropical rainforest in northern Costa Rica with ~4200 mm annual rainfall and a savanna in central Texas with ~1100 mm. Gas exchange measurements were collected under dry and wet conditions on five sun-exposed leaf replicates from each species. Additional measurements included leaf wetness duration and stomatal density. We found that Anet responses varied greatly among species, but all plants maintained a baseline of activity under wet leaf conditions, suggesting that abaxial leaf Anet was a significant percentage of total leaf Anet for amphistomatous species. Among tropical species, Anet responses immediately after wetting ranged from -31% (Senna alata (L.) Roxb.) to +21% (Zamia skinneri Warsz. Ex. A. Dietr.), while all savanna species declined (up to -48%). After 10 min of drying, most species recovered Anet towards the observed status prior to wetting or surpassed it, with the exception of Quercus stellata Wangenh., a savanna species, which remained 13% below Anet dry. The combination of leaf wetness duration and leaf traits, such as stomatal density, trichomes or wax, most likely influenced Anet responses positively or negatively. There was also overlap between leaf traits and Anet responses of savanna and tropical plants. It is possible that these species converge on a relatively conservative response to wetness, each for divergent purposes (cooling, avoiding stomatal occlusion, or by several unique means of rapid drying). A better understanding of leaf wetness inhibiting photosynthesis is vital for accurate modeling of growth in forested environments; however, species adapted for wet environments may possess compensatory traits that mitigate these effects.
When optimizing a product or process with multiple responses, a two-stage Pareto front approach is a useful strategy to evaluate and balance trade-offs between different estimated responses to seek optimum input locations for achieving the best outcomes. After objectively eliminating non-contenders in the first stage by looking for a Pareto front of superior solutions, graphical tools can be used to identify a final solution in the second subjective stage to compare options and match with user priorities. Until now, there have been limitations on the number of response variables and input factors that could effectively be visualized with existing graphical summaries. We present novel graphical tools that can be more easily scaled to higher dimensions, in both the input and response spaces, to facilitate informed decision making when simultaneously optimizing multiple responses. A key aspect of these graphics is that the potential solutions can be flexibly sorted to investigate specific queries, and that multiple aspects of the solutions can be simultaneously considered. As a result, recommendations are made about how to evaluate the impact of the uncertainty associated with the estimated response surfaces on decision making with higher dimensions.
Transition metal carbides (TMCs) have attracted significant attention because of their applications toward a wide range of catalytic transformations. However, the practicality of their synthesis is still limited because of the harsh conditions in which most TMCs are prepared. Recently, a solution-phase synthesis of phase-pure a-MoC1-x nanoparticles was presented. While this synthetic route yielded nanoparticles with exceptional catalytic performance, the reaction parameter space was not explored, and catalyst throughput was not optimized for scale-up. Continuous flow platforms coupled with statistical design of experiments (DoE) can provide a powerful method for understanding the reaction parameter space for optimizations. Here, we demonstrate the use of statistical DoE in tandem with response surface methodology for a parametric screening analysis to optimize the throughput of a MoC1-x nanoparticle synthesis utilizing a millifluidic flow reactor. A full factorial design was implemented to evaluate four input variables (reaction temperature, flow rate, solvent fraction of oleylamine, and precursor concentration) that carry statistically significant effects on three responses (throughput, residence time, and isolated yield). A Doehlert matrix was implemented to investigate each significant variable at a higher number of levels to optimize throughput. Our results give a nonintuitive set of experimental conditions that resulted in an optimized throughput of 2.2 g h-1. This translates to a 50-fold increase in throughput compared to the previously reported batch method. The catalytic performance of the MoC1-x nanoparticles produced under optimized throughput was demonstrated in the CO2 hydrogenation reaction. This DoE screening analysis and throughput optimization of MoC1-x synthesis open the door to an increased feasibility for scale-up.
Changes in proximate composition of fish and rice flour coextrudates like moisture, protein, and fat content were studied with respect to extrusion process v ariables like barrel temperature, x1 (100–200 degrees C); screw speed, x2 (70–110 rpm); fish content of the feed, x3 (5–45 percent); and feed moisture content, x4 (20–60 percent). Experiments were conducted at five levels of the process variables based on rotatable experimental design. Response surface models (RSM) were developed that adequately described the changes in moisture, protein, and fat content of the extrudates based on the coeff icient of determination (R2) values of 0.95, 0.99, and 0.94. ANOVA analysis indicated that extrudate moisture content was influenced by x4, protein content by x1 and x3, and fat content by x3 and x4 at P < 0.001. Trends based on response surf ace plots indicated that the x1 of about 200 degrees C, x2 of about 90 rpm, x3 of about 25%, and x4 of about 20% minimized the moisture in the extrudates. Protein content was maximized at x1 of 100 degrees C, x2 > 80 rpm, x3 of about 45 percent, and x4 > 50 percent, and fat content was minimized at x1 of about 200 degrees C, x2 of about 85–95 rpm, x3 < 15 percent, and x4 of about >50 percent. Optimized process variables based on a genetic algorithm (GA) for minimum moisture and fat content and maximum protein content were x1 = 199.86, x2 = 109.86, x3 = 32.45, x4 = 20.03; x1 = 199.71, x2 = 90.09, x3 = 15.27, x4 = 58.47; and x1 = 102.97, x2 = 107.67, x3 = 44.56, x4 = 59.54. The predicted values were 17.52 percent, 0.57 percent, and 46.65 percent. Based on the RSM and GA analy sis, extrudate moisture and protein content was influenced by x1, x3, and x4 and fat content by x2, x3, and x4.
Multiphase computational fluid dynamics plays a major role in design and optimization of fossil fuel based reactors. There is a growing interest in accounting for the influence of uncertainties associated with physical systems to increase the reliability of computational simulation based engineering analysis. The U.S. Department of Energy's National Energy Technology Laboratory (NETL) has recently undertaken an initiative to characterize uncertainties associated with computer simulation of reacting multiphase flows encountered in energy producing systems such as a coal gasifier. The current work presents the preliminary results in applying non-intrusive parametric uncertainty quantification and propagation techniques with NETL's open-source multiphase computational fluid dynamics software MFIX. For this purpose an open-source uncertainty quantification toolkit, PSUADE developed at the Lawrence Livermore National Laboratory (LLNL) has been interfaced with MFIX software. In this study, the sources of uncertainty associated with numerical approximation and model form have been neglected, and only the model input parametric uncertainty with forward propagation has been investigated by constructing a surrogate model based on data-fitted response surface for a multiphase flow demonstration problem. Monte Carlo simulation was employed for forward propagation of the aleatory type input uncertainties. Several insights gained based on the outcome of these simulations are presented such as how inadequate characterization of uncertainties can affect the reliability of the prediction results. Also a global sensitivity study using Sobol' indices was performed to better understand the contribution of input parameters to the variability observed in response variable.
The discovery of topological phases has introduced a new dimension to materials science. Three-dimensional (3D) topological insulators (TIs) are a remarkable class of matter that is insulating in the bulk while hosting conductive topological surface states (TSSs) with unique charge and spin properties. High-order harmonic generation (HHG) has emerged as a powerful tool to probe condensed matter systems by providing insights into their electronic structure and dynamic behavior. Here, we investigate HHG in the prototype 3D-TI Bi$_2$Se$_3$. We demonstrate that the contributions of bulk and surface states to the harmonic emission can be controlled by tuning the thickness of thin film samples. An ultrathin (6 nm) film substantially enhances HHG from the surface states, while the bulk states dominate HHG in a thicker (50 nm) film. By applying a quasi-static terahertz perturbing field, we disentangle the bulk and surface responses and reveal the significant impact of the surface states' shift vector and Berry curvature on HHG. Our study provides effective methods for isolating the optical responses of TSSs from those of the bulk, which opens the door to resolving an ongoing debate regarding whether it is possible to reliably extract topological signatures in HHG.
The Arctic surface energy budget (SEB) couples the atmosphere with the sea ice, making it useful for both studying surface processes as well as evaluating models. Improved understanding of atmosphere-ice interactions is required to improve models, requiring year-round observations to address seasonally dependent biases. This work uses novel observations from the MOSAiC expedition to quantify the responses of surface fluxes to radiative forcing over sea ice throughout a complete annual cycle. We identify two primary regimes of flux response: an ice growth regime in winter and an ice melt regime in summer. In the growth regime, changes in radiative forcing impact upwelling longwave, sensible heat, and subsurface heat fluxes, whereas in the melt regime changes in radiative forcing primarily alter the amount of melt and subsurface transmission because the surface temperature is fixed. These observed responses of surface fluxes to radiative forcing are used to evaluate seven weather forecast models during the ice growth regime. In most models, the responses of surface fluxes to radiative forcing do not match observations. Many models also have biased downwelling longwave. One model (the Coupled Arctic Forecast System; CAFS) adequately captures both the mean radiative forcing and the flux responses in winter. CAFS is further evaluated against observations spanning the full MOSAiC year, demonstrating sufficient agreement to provide a more generalized understanding of these SEB process relationships across the Arctic.
In this study, we apply an uncertainty quantification (UQ) framework to CO2 sequestration problems. In one scenario, we look at the risk of wellbore leakage of CO2 into a shallow unconfined aquifer in an urban area; in another scenario, we study the effects of reservoir heterogeneity on CO2 migration. We combine various sampling approaches (quasi-Monte Carlo, probabilistic collocation, and adaptive sampling) in order to reduce the number of forward calculations while trying to fully explore the input parameter space and quantify the input uncertainty. The CO2 migration is simulated using the PNNL-developed simulator STOMP-CO2e (the water-salt-CO2 module). For computationally demanding simulations with 3D heterogeneity fields, we combined the framework with a scalable version module, eSTOMP, as the forward modeling simulator. We built response curves and response surfaces of model outputs with respect to input parameters, to look at the individual and combined effects, and identify and rank the significance of the input parameters.
Forecasting solar energy generation is a challenging task due to the variety of solar power systems and weather regimes encountered. Forecast inaccuracies can result in substantial economic losses and power system reliability issues. This paper presents a suite of generally applicable and value-based metrics for solar forecasting for a comprehensive set of scenarios (i.e., different time horizons, geographic locations, applications, etc.). In addition, a comprehensive framework is developed to analyze the sensitivity of the proposed metrics to three types of solar forecasting improvements using a design of experiments methodology, in conjunction with response surface and sensitivity analysis methods. The results show that the developed metrics can efficiently evaluate the quality of solar forecasts, and assess the economic and reliability impact of improved solar forecasting.
The blending of woody and herbaceous biomass can influence pellet quality and the energy consumption of the process. This work aims to understand the pelleting characteristics of 2-inch top-pine residue blended with switchgrass at high moisture content. The process variables tested are blend moisture content, length-to-diameter (L/D) ratio in the pellet die, and the blend ratio. A flat die pellet mill was also used in this study. The pine and switchgrass blend ratios that were tested include: (1) 25% 2-inch top pine residue with 75% switchgrass; (2) 50% 2-inch top pine residue with 50% switchgrass; and (3) 75% 2-inch top pine residue with 25% switchgrass. The pelleting process conditions tested included the L/D ratio in the pellet die (i.e., 1.5 to 2.6) and the blend moisture content (20 to 30%, w.b.). Analysis of experimental data indicated that blending 25% switchgrass with 75% 2-inch top pine residue and 50% switchgrass with 50% 2-inch top pine residue resulted in pellets with a bulk density of > 550 kg/m3 and durability of > 95%. Optimization of the response surface models developed for process conditions in terms of product properties indicated that a higher L/D ratio of 2.6 and a lower blend-moisture content of 20% (w.b.) maximized bulk density and durability. Higher pine in the blends improved the pellet durability and reduced energy consumption.
Pretreatment of lignocellulosic biomass at high temperatures or with oxidizing chemicals generate various inhibitors that restrict the efficient bioconversion of sugars in subsequent steps. The present study systematically investigates individual and combinatorial effects of pretreatment parameters on the generation of inhibitors. Herein, a plot between pretreatment temperature and inhibitor revealed optimum pretreatment temperature for energycane bagasse i.e., 170 °C beyond which total inhibitor production increased exponentially. No inhibitor production was observed on mechanical processing i.e., disk milling/cryogenic grinding of biomass. Evaluation of response surface regression exhibited that biomass solids loading has a significant effect on inhibitor generation at higher temperatures. The concentrations of certain inhibitors such as acetic acid, furfurals, and HMF increased more than 3-folds on doubling the solids loading. Furthermore, a novel low-severity approach of low-temperature hydrothermal pretreatment coupled with cryogenic grinding for lignocellulosic biomasses has been introduced which improved sugar yields while maintaining a low inhibitor concentration.
This paper describes a variable-pitch propeller testing and aerodynamic modeling methodology for electric vertical takeoff and landing (eVTOL) aircraft using wind tunnel testing. Propellers used for eVTOL aircraft propulsion systems experience a wide range of operating conditions resulting in significant variation of axial thrust and torque, as well as off-axis forces and moments, across a typical flight envelope. An experimental design is developed to collect informative wind tunnel data in an efficient manner using response surface methods. System identification methods are then applied to isolated propeller wind tunnel data to develop a mathematical model of the propeller valid throughout the transition envelope of a vectored-thrust eVTOL aircraft. Multiple explanatory variable definitions are postulated and compared using modeling and prediction performance metrics. Modeling results validated against data withheld from the modeling process indicate good predictive capability and agree with theoretical expectations. All identified propeller models are provided, which allows the models to be used in future eVTOL aircraft flight dynamics simulations.
VTMOP is a Fortran 2008 software package containing two Fortran modules for solving computationally expensive bound-constrained blackbox multiobjective optimization problems. VTMOP implements the algorithm of [32], which handles two or more objectives, does not require any derivatives, and produces well-distributed points over the Pareto front. The first module contains a general framework for solving multiobjective optimization problems by combining response surface methodology, trust region methodology, and an adaptive weighting scheme. The second module features a driver subroutine that implements this framework when the objective functions can be wrapped as a Fortran subroutine. Lastly, support is provided for both serial and parallel execution paradigms, and VTMOP is demonstrated on several test problems as well as one real-world problem in the area of particle accelerator optimization.
The U.S. Department of Energy National Energy Technology Laboratory's (NETL) 50 kW th chemical looping reactor (CLR) has an underperforming cyclone, which was designed using empirical correlations. To improve the performance of this cyclone using computational fluid dynamics (CFD)-based modeling simulations, four critical design parameters including the vortex tube radius and length, barrel radius, and the inlet width and height were optimized. Here, NETL's open source multiphase flow with interphase exchange (MFiX) CFD code has been used to model a series of cyclones by systematically varying the geometric design parameters. To perform the optimization process, the surrogate modeling and sensitivity analysis followed by the optimization capability in nodeworks was used. The basic methodology for the process is to employ a statistical design of experiments (DOE) method to generate sampling simulations that fill the design space. Corresponding CFD models are then created, executed, and postprocessed. A response surface is created to characterize the relationship between input parameters and the quantities of interest (QoI). Finally, the CFD-surrogate is used by an optimization method to find the optimal design condition based on the objective and constraints prescribed. The resulting optimal cyclone has a larger diameter and longer vortex tube, a larger diameter barrel, and a taller and narrower solids inlet. The improved design has a predicted pressure drop 11 times lower than the original design while reducing the mass loss by a factor of 2.3.