Search NASA⌕ Search

SEARCH · Search NASA

Results for “Rotor noise”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Effects of casing boundary-layer removal on noise of a turbofan rotor

The effect of casing boundary-layer removal on noise produced by a turbofan rotor was measured. The outlet guide vanes were removed for these tests. A comparison was made between the noise measurements when the boundary layer was bled off and under zero bleed conditions. When the boundary layer was removed, overall sound pressure level was reduced 2 dB with moderate blade loading and 3 dB with heavier blade loading. An analysis of the changes in the spectral density with bleed is presented.

Goldstein, A. W.↗
NASA NTRS1985

On helicopter rotor low frequency broadband noise

The effect of shear-layer-type inflow turbulence on the low-frequency broadband noise of a model helicopter rotor is experimentally studied. The measurements and the one-dimensional energy spectral density indicate that the upstream airfoil wake turbulence is nonisotropic, but approaches isotropy at high wavenumbers. Turbulence measurements also indicate that the wake turbulence is weak. The effect of the inflow turbulence intensity on the peak sound pressure level follows an intensity-velocity squared scaling law. A number of length scales and turbulence intensities exist which can be measured in the airfoil wake depending on the position at which the measurements are taken. Comparison of experimental and theoretical sound pressure power spectral densities indicates that the initial anisotropy of the inflow turbulence does not invalidate the isotropic turbulence assumption made in noise prediction models as long as measured turbulence intensities and length scales are used.

Williams, Morgan↗
NASA NTRS1983

On high frequency broadband noise from model helicopter rotors

An experimental investigation was carried out to study high frequency broadband noise (HFBN) from model helicopter rotors at a range of tip Mach numbers up to 0.40. The type of HFBN in the present case was due to boundary layer self noise (BLSN). The effects of rotor advance ratio, tip speed, blade tip geometry, and free stream turbulence on the intensity and spectrum of BLSN have been investigated. Saturation or fall-off of the peak sound pressure level was observed as the tip Mach number was varied from 0.20 to 0.40. This result is different from measurements on square tip blades reported earlier by Aravamudan, Lee and Harris (1979). An explanation of this difference along with a discussion of the effects of blade tip geometry on BLSN are provided.

Humbad, N. G.↗
NASA NTRS1996

Aeroacoustic Codes For Rotor Harmonic and BVI Noise--CAMRAD.Mod1/HIRES

This paper presents a status of non-CFD aeroacoustic codes at NASA Langley Research Center for the prediction of helicopter harmonic and Blade-Vortex Interaction (BVI) noise. The prediction approach incorporates three primary components: CAMRAD.Mod1 - a substantially modified version of the performance/trim/wake code CAMRAD; HIRES - a high resolution blade loads post-processor; and WOPWOP - an acoustic code. The functional capabilities and physical modeling in CAMRAD.Mod1/HIRES will be summarized and illustrated. A new multi-core roll-up wake modeling approach is introduced and validated. Predictions of rotor wake and radiated noise are compared with to the results of the HART program, a model BO-105 windtunnel test at the DNW in Europe. Additional comparisons are made to results from a DNW test of a contemporary design four-bladed rotor, as well as from a Langley test of a single proprotor (tiltrotor) three-bladed model configuration. Because the method is shown to help eliminate the necessity of guesswork in setting code parameters between different rotor configurations, it should prove useful as a rotor noise design tool.

Brooks, Thomas F.↗
NASA NTRS1990

Wake Geometry Effects on Rotor Blade-Vortex Interaction Noise Directivity

Acoustic measurements from a model rotor wind tunnel test are presented which show that the directionality of rotor blade vortex interaction (BVI) noise is strongly dependent on the rotor advance ratio and disk attitude. A rotor free wake analysis is used to show that the general locus of interactions on the rotor disk is also strongly dependent on advance ratio and disk attitude. A comparison of the changing directionality of the BVI noise with changes in the interaction locations shows that the strongest noise radiation occurs in the direction of motion normal to the blade span at the time of interaction, for both advancing and retreating side BVI. For advancing side interactions, the BVI radiation angle down from the tip-path plane appears relatively insensitive to rotor operating condition and is typically between 40 and 55 deg below the disk. However, the azimuthal radiation direction shows a clear trend with descent speed, moving towards the right of the flight path with increasing descent speed. The movement of the strongest radiation direction is attributed to the movement of the interaction locations on the rotor disk with increasing descent speed.

Martin, R. M.↗
NASA NTRS1974

Theoretical studies on tone noise from a ducted fan rotor

The method of computing radiated noise from a ducted rotor due to inflow distortion and turbulence are examined. Analytical investigations include an appropriate description of sources, the cut-off conditions imposed on the modal propagation of the pressure waves in the annular duct, and reflections at the upstream end of the duct. Far field sound pressure levels at blade passing frequency due to acoustic radiation from a small scale low speed fan are computed. Theoretical predictions are in reasonable agreement with experimental measurements.

Rao, C. V. R.↗
NASA NTRS1990

Prediction of XV-15 tilt rotor discrete frequency aeroacoustic noise with WOPWOP

The results, methodology, and conclusions of noise prediction calculations carried out to study several possible discrete frequency harmonic noise mechanisms of the XV-15 Tilt Rotor Aircraft in hover and helicopter mode forward flight are presented. The mechanisms studied were thickness and loading noise. In particular, the loading noise caused by flow separation and the fountain/ground plane effect were predicted with calculations made using WOPWOP, a noise prediction program developed by NASA Langley. The methodology was to model the geometry and aerodynamics of the XV-15 rotor blades in hover and steady level flight and then create corresponding FORTRAN subroutines which were used an input for WOPWOP. The models are described and the simplifying assumptions made in creating them are evaluated, and the results of the computations are presented. The computations lead to the following conclusions: The fountain/ground plane effect is an important source of aerodynamic noise for the XV-15 in hover. Unsteady flow separation from the airfoil passing through the fountain at high angles of attack significantly affects the predicted sound spectra and may be an important noise mechanism for the XV-15 in hover mode. The various models developed did not predict the sound spectra in helicopter forward flight. The experimental spectra indicate the presence of blade vortex interactions which were not modeled in these calculations. A need for further study and development of more accurate aerodynamic models, including unsteady stall in hover and blade vortex interactions in forward flight.

Coffen, Charles D.↗
NASA NTRS1982

Model helicopter rotor low frequency broadband noise

The results of an experimental investigation of low frequency broadband noise (LFBN) radiated from model helicopter rotors are presented. The results up to tip Mach number of 0.50 suggest that the peak sound pressure level (SPL) of LFBN appears to follow tip Mach number to a fourth power law and rms velocity of turbulence to a second power law. The experimental results on the effect of tip speed and advance ratio on the peak SPL of LFBN can be explained on the basis of a simple scaling law. However, the experimental results on the effect of blade loading on the peak SPL of LFBN is still not clearly understood. A simple peak SPL scaling law for noise from a helicopter in forward flight encountering a sinusoidal gust is also developed. The trends predicted by the scaling law with the experimental results are found satisfactory for the cases of variation of the peak SPL of LFBN with tip speed and advance ratio.

Humbad, N. G.↗
NASA NTRS2022

Identification and Reduction of Interactional Noise of a Quadcopter in Hover and Forward Flight Conditions

Advanced Air Mobility is a vision for a safe, accessible, and sustainable aviation system to transport people and cargo between places not served by traditional aviation. With this emerging transportation industry, there is motivation to characterize the noise of vehicles to determine their potential impacts on the community. An experimental testing campaign was conducted on a representative model of a small unmanned aircraft system in the NASA Langley Low Speed Aeroacoustic Wind Tunnel as a continuation of a previous testing campaign. The goals of the current test are to identify sources of interactional noise as well as to test custom-designed rotors and noise reduction devices. The tested noise reduction methods involve increasing the vertical distances between the rotors and the vehicle airframe as well as between the forward and aft rotor disk planes. These methods are intended to reduce rotor-airframe interaction noise in hover and fore-aft rotor wake ingestion noise in forward flight. A phased microphone array is also utilized to identify the locations of prominent noise generation for the different vehicle configurations in forward flight. Elevation of the rotors from the vehicle airframe yielded nearly 8 dBA overall noise reduction in forward flight, while yielding up to 4 dB reduction in overall tonal levels for one of the rotors in hover.

Nikolas S Zawodny↗
NASA NTRS1977

An experimental investigation of helicopter rotor high frequency broadband noise

The paper describes experiments involving a 4.17 foot diameter model rotor operating in a 5 times 7.5 ft open jet wind tunnel enclosed in an anechoic chamber. The effects of rotor thrust, advance ratio, and the number of blades on the intensity and spectrum of high frequency broadband noise (HFBN) have been investigated. The effects of each parameter were determined by keeping the other two constant. The directivities of the two- and three-bladed rotors were measured in a direction perpendicular to the plane of the rotor disk. The effects of heading edge, pressure side, and suction side serrations on HFBN were measured under several operating conditions, and the effects of the serrations on the mean thrust generated by the rotor were studied. A scaling law is proposed to determine the location of the peak frequency and intensity of HFBN.

Lee, A.↗
NASA NTRS1972

Methods for reducing blade passing frequency noise generated by rotor-wake - stator interaction

A theoretical model for the generation of blade-passage noise caused by the interaction of rotor wakes with the downstream stator blades in a fan stage has been compiled. This model has combined a description of the rotor wake based on existing experimental correlations with an existing theory for the response of the stator blades to those wakes. This model of the interaction-caused blade-passage noise has been used to examine some effects of blade geometry and flow conditions on the noise generated. A set of significant parameters has been identified to reduce this interaction-caused blade-passage frequency noise. A redesign of an existing fan with the use of these concepts has produced a theoretical noise reduction of more than 7 decibels.

Dittmar, J. H.↗
NASA NTRS2011

Fundamental Rotorcraft Acoustic Modeling From Experiments (FRAME)

A new methodology is developed for the construction of helicopter source noise models for use in mission planning tools from experimental measurements of helicopter external noise radiation. The models are constructed by employing a parameter identification method to an assumed analytical model of the rotor harmonic noise sources. This new method allows for the identification of individual rotor harmonic noise sources and allows them to be characterized in terms of their individual non-dimensional governing parameters. The method is applied to both wind tunnel measurements and ground noise measurements of two-bladed rotors. The method is shown to match the parametric trends of main rotor harmonic noise, allowing accurate estimates of the dominant rotorcraft noise sources to be made for operating conditions based on a small number of measurements taken at different operating conditions. The ability of this method to estimate changes in noise radiation due to changes in ambient conditions is also demonstrated.

Greenwood, Eric↗
NASA NTRS1973

Leading edge serrations which reduce the noise of low-speed rotors

Acoustic effects of serrated brass strips attached near the leading edges of two different size rotors were investigated. The two bladed rotors were tested in hover. Rotor rotational speed, blade angle, serration shape, and serration position were varied. The serrations were more effective as noise suppressors at rotor tip speeds less than 135 m/sec (444 ft/sec) than at higher speeds. high frequency noise was reduced but the low frequency rotational noise was little affected. Noise reductions from 4 to 8 db overall sound pressure level and 3 to 17 db in the upper octave bands were achieved on the 1.52 m (5.0 ft) diameter rotor. Noise reductions up to 4 db overall sound pressure level were measured for the 2.59 m (8.5 ft) diameter rotor at some conditions.

Soderman, P. T.↗
NASA NTRS1978

Improved methods for calculating the thickness noise

Advanced methods to compute the rotor thickness noise which is predominant in the case of high speed rotor were developed. These methods were deduced from a previous method by transforming the integral coordinate, commuting the order of integration and differential, and/or performing chordwise integration analytically with some adequate assumption. The necessary computational times and waveforms obtained by the previous and three advanced methods were compared. It was then concluded that the advanced methods could save the computational time compared with the previous method with the same accuracy.

Nakamura, Y.↗
NASA NTRS2010

A Parameter Identification Method for Helicopter Noise Source Identification and Physics-Based Semi-Empirical Modeling

A new physics-based parameter identification method for rotor harmonic noise sources is developed using an acoustic inverse simulation technique. This new method allows for the identification of individual rotor harmonic noise sources and allows them to be characterized in terms of their individual non-dimensional governing parameters. This new method is applied to both wind tunnel measurements and ground noise measurements of two-bladed rotors. The method is shown to match the parametric trends of main rotor Blade-Vortex Interaction (BVI) noise, allowing accurate estimates of BVI noise to be made for operating conditions based on a small number of measurements taken at different operating conditions.

Greenwood, Eric, II↗
NASA NTRS2023

Blade-Wake Interaction Noise for Small Hovering Rotors, Part I: Characterization Study

This work illustrates the use of artificial neural network modeling to study and characterize broadband blade-wake interaction noise from hovering small unmanned aerial systems rotors subject to varying airfoil geometries, rotor geometries, and operating conditions. Design of experiments was used to create input feature spaces, and a high-fidelity strategy was implemented at the discrete data points defined by the input feature spaces to design airfoils and rotor blades, predict the unsteady rotor aerodynamics and aeroacoustics, and isolate the blade-wake interaction noise from the acoustic broadband noise. A metric for the blade-wake interaction noise was developed, and the ANOPP2 Artificial Neural Network Tool was used to identify an optimal prediction model for the nonlinear relationship between the input features and the metric for blade-wake interaction noise. This optimal artificial neural network was then validated over training/test data and exhibited prediction accuracy over 91% for data previously unseen by the model. A sensitivity analysis was conducted, which showed that input features that directly modify the thrust coefficient had a dominant effect over blade-wake interaction noise. The optimal prediction model along with aerodynamic simulations were used to further study the effect of varying input features on blade-wake interaction noise, and three types of blade-wake interaction noise were identified

Christopher S. Thurman↗