Search NASA⌕ Search

SEARCH · Search NASA

Results for “SINTERED INTERFACES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Evidence that Surface-Segregated Sr Phases Can Be Removed in LSCF via Ceria Pre-Infiltration, Are Less Apt to Form in SSC

Here Ce 0.9 Gd 0.1 O 1.95−x (GDC) pre-infiltration was performed on 12 vol.% La 0.6 Sr 0.4 Co 0.8 Fe 0.2 O 3−x (LSCF) or Sm 0.5 Sr 0.5 CoO 3−x (SSC) infiltrated GDC Solid Oxide Fuel Cell cathodes. The addition of 7.5 vol.% of ∼40 nm diameter GDC nanoparticles into a ∼30 μ m thick porous scaffold of partially-sintered, sub-micron GDC particles before LSCF infiltration 1) lowered the temperature needed to produce a LSCF-GDC polarization resistance ( R P ) of 0.1 Ohm*cm 2 by ∼50 °C, and 2) reduced the amount of 500 h, 650 °C open-circuit LSCF-GDC R P degradation from ∼37% to ∼6%. In contrast, GDC pre-infiltration had no effect on the initial SSC-GDC R P or the 19% in R P degradation observed during 500 h of 650 °C open-circuit aging. X-Ray Photoelectron Spectroscopy showed that GDC pre-infiltration lowered the concentration of strontium species on the surface of the initial and 650 °C-aged LSCF-GDC, but had no effect on the initial or aged SSC-GDC Sr concentrations. Similarly, Electrochemical Impedance Spectroscopy showed that for both the initial and aged LSCF-GDC, GDC pre-infiltration improved oxygen exchange at the infiltrate-backbone and infiltrate-gas interfaces, but had no effect on the SSC-GDC. Hence, GDC pre-infiltration was concluded to improve LSCF-GDC performance and durability by scavenging exsolved Sr-rich secondary phases that form on the interfaces of LSCF, but not SSC.

36 MATERIALS SCIENCE↗

Low Thermal Conductivity, High Durability Thermal Barrier Coatings for IGCC Environments

Advanced thermal barrier coatings (TBC) are crucial to improved energy efficiency in next generation gas turbine engines. The use of traditional topcoat materials, e.g. yttria-stabilized zirconia (YSZ), is limited at elevated temperatures due to (1) the accelerated undesirable phase transformations and (2) corrosive attacks by calcium-magnesium-aluminum-silicate (CMAS) deposits and moisture. The first goal of this project is to use the Solution Precursor Plasma Spray (SPPS) process to further reduce the thermal conductivity of YSZ TBCs by introducing a unique microstructural feature of layered porosity, called inter-pass boundaries (IPBs). Extensive process optimization accompanied with hundreds of spray trials as well as associated SEM cross-section and laser-flash measurements, yielded a thermal conductivity as low as 0.62 Wm⁻¹K⁻¹ in SPPS YSZ TBCs, approximately 50% reduction of APS TBCs; while other engine critical properties, such as cyclic durability, erosion resistance and sintering resistance, were characterized to be equivalent or better than APS baselines. In addition, modifications were introduced to SPPS TBCs so as to enhance their resistance to CMAS under harsh IGCC environments. Several mitigation approaches were explored, including doping the coatings with Al₂O₃ and TiO₂, applying a CMAS infiltration-inhibiting surface layer, and filling topcoat cracks with blocking substances. The efficacy of all these modifications was assessed with a set of novel CMAS-TBC interaction tests, and the moisture resistance was tested in a custom-built high-temperature moisture rig. In the end, the optimal low thermal conductivity TBC system was selected based on all evaluation tests and its processing conditions were documented. The optimal coating consisted on a thick inner layer of YSZ coating made by the SPPS process having a thermal conductivity 50% lower than standard YSZ coatings topped with a high temperature tolerant CMAS resistant gadolinium zirconate Coating made by the SPPS process. Noteworthy was the fact that the YSZ to GZO interface made by the SPPS process was not the failure location as had been observed in APS coatings.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

High Damping of Lightweight TiNi-Ti{sub 2}Ni Shape Memory Composites for Wide Temperature Range Usage

A bimodal porous TiNi-Ti{sub 2}Ni shape memory alloy composite (SMAC) with 59% porosity was fabricated by sintering Ti-46at.%Ni elemental powders with pore-forming agent. The porous TiNi-Ti{sub 2}Ni SMAC contains two irregular pores of about 400 and 120 μm. We investigated the microstructure and pore morphology correlated with the mechanical properties and damping capacities of the SMAC. Ti{sub 2}Ni intermetallic phases with size of 1-3 μm were homogeneously distributed in the TiNi matrix. The porous TiNi-Ti{sub 2}Ni SMAC exhibits exceptionally high inverse mechanical quality factor (Q{sup −1}) of ~0.25 at < 40 °C, which is among the highest value reported for porous/dense shape memory alloys or composites to best of our knowledge, and it shows very high compressive fracture strain of about 25%. Moreover, the fabricated porous SMAC at relatively low strain amplitude can exhibit considerable high Q{sup −1} of 0.06 ~ 0.11 for a wide range of temperature between − 90 and 200 °C, which is attributed to the stress concentration distribution provided by the bimodal structure of pores and the massive interfaces between pore/matrix and TiNi/Ti{sub 2}Ni. These porous SMACs can be an ideal candidate for using as a lightweight damping material in the energy-saving applications.

36 MATERIALS SCIENCE↗

Self-Stabilized LiNi 0.8 Mn 0.1 Co 0.1 O 2 in thiophosphate-based all-solid-state batteries through extra LiOH

Nickle-rich LiNi 0.8 Co 0.1 Mn 0.1 O 2 (NMC 811) cathode material exhibits engaging properties in high energy density and low cost, making it great potential for the next generation high-energy all-solid-state lithium batteries (ASSLBs). However, NMC 811 suffers from severe surface electrochemical, chemical, and voltage incompatibility towards solid-state electrolytes (SSE), especially thiophosphate-based electrolytes like Li 6 PS 5 Cl. Although diverse coating methods have been made to overcome this issue, they are typically cumbersome and expensive. A coating strategy that satisfied all the requirements of cost-efficiency, stability, uniformity, scalability, and easy-achieving is still challenging. Here, we developed a LiOH-based surface stabilization strategy that provides a ~10 nm stable permeable layer on NMC 811. After one-step sintering of NMC 811 precursor mixed with LiOH, which is commonly used for NMC 811 lithiation process, excessive LiOH simultaneously distributes on NMC 811 particles. Unlike other reported methods, this coating method can be easily controlled and fabricated without additional complicated processes. By simply controlling the thickness of LiOH layer, which protects the Li 6 PS 5 Cl solid electrolyte materials from being oxidized, optimized cycling stability can be obtained for 600 cycles with capacity of 130 mAh g – 1 on average at a wide electrochemical window of 2.50–4.20 V (vs. Li-In).

25 ENERGY STORAGE↗

Predicting Adhesion Energies of Metal Nanoparticles to Support Surfaces, Which Determines Metal Chemical Potential versus Particle Size and Thus Catalyst Performance

Improved catalysts and electrocatalysts composed of transition metal nanoparticles dispersed on high-area supports are essential for energy and environmental technologies. The chemical potential of the metal atoms in these supported nanoparticles is an important descriptor that correlates with both their catalytic activity and deactivation rate. This descriptor (μ M ) is predictably determined by the particle size and the adhesion energy per unit area at the metal/support interface (E adh ). We show here that the adhesion energies for different metals on a given support scale linearly with a simple property of the metal: for oxides, it is proportional to the metal oxophilicity, and for the carbon support, it increases linearly with metal carbophilicity (both divided by the area per metal atom). Furthermore, these relationships allow predicting E adh for other metal/support combinations, thus allowing estimation of μ M versus particle size and thereby better structure-based predictions of catalysts’ performance, which can aid in designing improved catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

The Nature of the Nonsingularity of Inner Interfaces in Hydroxyapatite Ceramics

The morphology of inner interfaces in hydroxyapatite (HA) based calcium phosphate ceramics has been studied by transmission electron microscopy. Grain boundaries in the ceramics have been shown to have a vicinal character, which is related to the mechanism of secondary recrystallization in the material: layer growth of grains via sequential motion of elementary steps on planes corresponding to the {11̄00} HA prism faces, which grow through transitions of atoms from adjacent grains that are in contact through their planes with large Miller indices. The recrystallization process may be accompanied by a “collision” of vicinal growth surfaces of grains with relatively large misalignment angles and the formation of grain boundaries nanofaceted by prism planes of adjacent grains. The recrystallization process in such a case should be expected to continue in the grain with a smaller nonsingularity of the growth front. Grain boundaries may allow for a match between planes differing in Miller indices, nd{sub h1k1l1} ≈ md{sub h2k2l2}, and the formation of grain-boundary Pumphrey dislocations, which compensate for the size mismatch between interplanar spacings and/or misalignment of the planes. The observed characteristic grain match configurations are typical of both ceramics produced by sintering HA powders and HA films produced by ion sputtering.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

NASA Tech Briefs, August 2011

Topics covered include: Miniature, Variable-Speed Control Moment Gyroscope; NBL Pistol Grip Tool for Underwater Training of Astronauts; HEXPANDO Expanding Head for Fastener-Retention Hexagonal Wrench; Diagonal-Axes Stage for Pointing an Optical Communications Transceiver; Improvements in Speed and Functionality of a 670-GHz Imaging Radar; IONAC-Lite; Large Ka-Band Slot Array for Digital Beam-Forming Applications; Development of a 150-GHz MMIC Module Prototype for Large-Scale CMB Radiation; Coupling Between Waveguide-Fed Slot Arrays; PCB-Based Break-Out Box; Multiple-Beam Detection of Fast Transient Radio Sources; Router Agent Technology for Policy-Based Network Management; Remote Asynchronous Message Service Gateway; Automatic Tie Pointer for In-Situ Pointing Correction; Jitter Correction; MSLICE Sequencing; EOS MLS Level 2 Data Processing Software Version 3; DspaceOgre 3D Graphics Visualization Tool; Metallization for Yb14MnSb11-Based Thermoelectric Materials; Solvent/Non-Solvent Sintering To Make Microsphere Scaffolds; Enhanced Fuel-Optimal Trajectory-Generation Algorithm for Planetary Pinpoint Landing; Self-Cleaning Coatings and Materials for Decontaminating Field-Deployable Land and Water-Based Optical Systems; Separation of Single-Walled Carbon Nanotubes with DEP-FFF; Li Anode Technology for Improved Performance; Post-Fragmentation Whole Genome Amplification-Based Method; Microwave Tissue Soldering for Immediate Wound Closure; Principles, Techniques, and Applications of Tissue Microfluidics; Robotic Scaffolds for Tissue Engineering and Organ Growth; Stress-Driven Selection of Novel Phenotypes; Method for Accurately Calibrating a Spectrometer Using Broadband Light; Catalytic Microtube Rocket Igniter; Stage Cylindrical Immersive Display; Vacuum Camera Cooler; Atomic Oxygen Fluence Monitor; Thermal Management Tools for Propulsion System Trade Studies and Analysis; Introduction to Physical Intelligence; Technique for Solving Electrically Small to Large Structures for Broadband Applications; Accelerated Adaptive MGS Phase Retrieval; Large Eddy Simulation Study for Fluid Disintegration and Mixing; Tropospheric Correction for InSAR Using Interpolated ECMWF Data and GPS Zenith Total Delay; Technique for Calculating Solution Derivatives With Respect to Geometry Parameters in a CFD Code; Acute Radiation Risk and BRYNTRN Organ Dose Projection Graphical User Interface; Probabilistic Path Planning of Montgolfier Balloons in Strong, Uncertain Wind Fields; Flight Simulation of ARES in the Mars Environment; Low-Outgassing Photogrammetry Targets for Use in Outer Space; Planning the FUSE Mission Using the SOVA Algorithm; Monitoring Spacecraft Telemetry Via Optical or RF Link; and Robust Thermal Control of Propulsion Lines for Space Missions.

Source record↗

Cost-effective Manufacturing and Morphological Stabilization of Nanostructured Cathodes for Commercial SOFCs

The overall goals of the program were to develop methods for preparing and stabilizing SOFC electrodes by infiltration that can be manufactured on a practical scale, then transfer those methods to cells in stacks. Cathodes prepared by infiltration of nanoparticles into a porous scaffold of the electrolyte have demonstrated outstanding electrochemical performance and mechanical strength but are difficult to manufacture due to the large number of infiltration steps required to produce a conductive composite and show poor stability due to sintering of the nanoparticles. At Penn, the main goal was to develop a fabrication method that uses only a small number of infiltration steps. Infiltration with molten salts and electrodeposition were pursued but deemed impractical. A method in which an electronically conductive scaffold consisted of a composite of a mixed conductor, LSF (La 0.9 Sr 0.1 FeO 3 ), with yttria-stabilized zirconia (YSZ) was found to be promising. While some cation mixing between LSF and YSZ was observed during calcination, there was no evidence for new phases in XRD and incorporation of Zr into the perovskite could be minimized by reducing the Sr content of the LSF. To stabilize nanoparticles infiltrated into the LSF-YSZ composite scaffold, the USC team examined the effects of Atomic Layer Deposition with ZrO 2 and infiltrated nanoparticles. Significantly enhanced stability was observed with the infiltrated nanoparticles. The FuelCell Energy team prepared 4”x4” cells in which an LSF-YSZ composite scaffold was cofired with the YSZ electrolyte and infiltrated with LSCF nanoparticles. Apparently because the LSF-YSZ scaffold layer was very thin in this case, the cation mixing that occurred during calcination resulted in a poor scaffold-electrolyte interface which caused reduced performance.

36 MATERIALS SCIENCE↗

Cost-effective Manufacturing and Morphological Stabilization of Nanostructured Cathodes for Commercial Solid Oxide Fuel Cells (SOFCs) [Slides]

The overall goals of the program were to develop methods for preparing and stabilizing SOFC electrodes by infiltration that can be manufactured on a practical scale, then transfer those methods to cells in stacks. Cathodes prepared by infiltration of nanoparticles into a porous scaffold of the electrolyte have demonstrated outstanding electrochemical performance and mechanical strength but are difficult to manufacture due to the large number of infiltration steps required to produce a conductive composite and show poor stability due to sintering of the nanoparticles. At Penn, the main goal was to develop a fabrication method that uses only a small number of infiltration steps. Infiltration with molten salts and electrodeposition were pursued but deemed impractical. A method in which an electronically conductive scaffold consisted of a composite of a mixed conductor, LSF (La 0.9 Sr 0.1 FeO 3 ), with yttria-stabilized zirconia (YSZ) was found to be promising. While some cation mixing between LSF and YSZ was observed during calcination, there was no evidence for new phases in XRD and incorporation of Zr into the perovskite could be minimized by reducing the Sr content of the LSF. To stabilize nanoparticles infiltrated into the LSF-YSZ composite scaffold, the USC team examined the effects of Atomic Layer Deposition with ZrO 2 and infiltrated nanoparticles. Significantly enhanced stability was observed with the infiltrated nanoparticles. The FuelCell Energy team prepared 4”x4” cells in which an LSF-YSZ composite scaffold was cofired with the YSZ electrolyte and infiltrated with LSCF nanoparticles. Apparently because the LSF-YSZ scaffold layer was very thin in this case, the cation mixing that occurred during calcination resulted in a poor scaffold-electrolyte interface which caused reduced performance.

30 DIRECT ENERGY CONVERSION↗

Scalable and Cost-Effective Barrier Layer Coating to Improve Stability and Performance of SOFC Cathode

During this project, a dense GDC barrier layer was deposited on YSZ substrate to prevent chemical reaction between LSCF and YSZ by a cost-effective EPD method. PPy was used as the agent to make YSZ conductive. Highly compact GDC green layer was obtained by the EPD process in an ethanol-based suspension. The deposition rate on PPy coated YSZ is slower than that on graphite because the charge transfer process is the rate-determining step. The main resistance is from the ion accumulation/depletion zone. The H + ions reduced at the cathode consist of free H + ions and absorbed H + ions corresponding to the unavoidable electrochemical reaction and deposition, respectively. A factor f was introduced to reflects EPD efficiency and describe the competitive relationship between deposition and electrochemical reaction during EPD process. f is in the range from 0 to 0.5 which is determined by the amount ration between free H + ions and absorbed H + ions at the suspension/deposit interface and the conductivity of the cathode. f decreases with the increase of current density or applied voltage and the conductivity of the cathode. GDC thin layers formed by DC-EPD in a thickness range of 5-8 µm were successfully densified at as low as 1300 °C and the adhesion between GDC and YSZ was good. The densification temperature can be further reduced to 1250 °C when AC-EPD was used to replace DC-EPD. The deposition rate increases with the increase of duty cycle and voltage ratio. The deposition rate increases with the increase of frequency from 10 Hz to 500 Hz, while decrease when the frequency increases from 500 Hz to 5000 Hz. Desorption of absorbed charge carrier is easy and irreversible. The deposition rate is independent on the conductivity of the cathode when the electrochemical reaction can be ignored with a high frequency. Inter-diffusion of cation ions between the electrolyte and barrier layer has been systematically characterized via 3-D atom probe, TEM, and other techniques. No measurable Sr transport occurs across the GDC layer with a thickness of 1.5 – 6 μm at a LSCF processing temperature of 1000 °C. However, Sr transport does occur across GDC layer with a thickness of 1.5 or 3 μm at a higher LSCF sintering temperature (1000 °C or 1200 °C). The primary pathway are open pores or grain boundaries in the GDC. The observed zirconate layer is discontinuous even for the most extreme conditions (1.5 μm GDC, 1200 °C LSCF sintering temperature). Increasing the thickness of GDC to 4.5 μm can effectively suppress any zirconate formation measurable by SEM-EDX. Cobalt is observed at grain boundaries within the GDC, suggesting some depletion of Co from the LSCF layer that may ultimately impact electrode performance.

08 HYDROGEN↗

Evolution of Ni-Mo/MgO during catalytic methane pyrolysis to produce base-growth nanotubes

Catalytic pyrolysis of methane is a promising approach for affordable hydrogen production without CO 2 emissions. While this process is thermodynamically appealing compared to steam reforming, the high stability of methane requires severe conditions, making catalyst stability challenging. Here, we report the behavior of a highly promising Ni-Mo/MgO catalyst, which greatly outperforms its Ni/MgO, Mo/MgO, and Ni-Mo/SiO 2 counterparts at atmospheric pressure. At 800°C, nearly 229 g of carbon nanotubes per gram of Ni are produced. We propose that this superior performance results from the phase evolution of the catalyst, which exsolves stable nickel catalyst particles under reaction conditions. We further reveal that molybdenum carbide formation reduces sintering and adheres the active catalytic particles to the support throughout the reaction, enabling catalyst reuse. Several characterization techniques (same-spot TEM, XPS, XRD, and Raman) are employed to examine catalyst morphology at every step, fostering a deeper understanding of its catalytic activity and stability.

36 MATERIALS SCIENCE↗

Dynamic Evolution of Palladium Single Atoms on Anatase Titania Support Determines the Reverse Water–Gas Shift Activity

Research interest in single-atom catalysts (SACs) has been continuously rising. However, the lack of understanding of the dynamic behaviors of SACs during applications hinder catalyst development and mechanistic understanding. Herein, we report on the evolution of active sites over Pd/TiO 2 -anatase SAC (Pd 1 /TiO 2 ) in the reverse water-gas shift (rWGS) reaction. Combining kinetics, in-situ characterization, and theory, we show that at T ≥ 350 °C, the reduction of TiO 2 by H 2 alters the coordination environment of Pd, creating Pd sites with partially cleaved Pd-O interfacial bonds and a unique electronic structure that exhibit high intrinsic rWGS activity through the carboxyl pathway. The activation by H 2 is accompanied by the partial sintering of single Pd atoms (Pd 1 ) into disordered, flat, ~1 nm diameter clusters (Pd n ). The highly active Pd sites in the new coordination environment under H 2 are eliminated by oxidation, which, when performed at high temperature, also re-disperses Pd n and facilitates the reduction of TiO 2 . In contrast, Pd 1 sinters into crystalline, ~5 nm particles (Pd NP ) during CO treatment, deactivating Pd 1 /TiO 2 . During the rWGS reaction, the two Pd evolution pathways co-exist. The activation by H 2 dominates, leading to the increasing rate with time-on-stream, and steady-state Pd active sites similar with the ones formed under H 2 . Finally, this work demonstrates how the coordination environment and nuclearity of metal sites on a SAC evolve during catalysis and pre-treatments, and how their activity is modulated by these behaviors. These insights on SAC dynamics and structure-function relationship are valuable to mechanistic understanding and catalyst design.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Unraveling the multi-step crystallization mechanism of polytetrafluoroethylene, modified polytetrafluoroethylene, and their nanocomposites with boron nitride nanobarbs: Experimental insights and theoretical analysis

The non-isothermal crystallization behavior and kinetics of polytetrafluoroethylene (PTFE) composites with boron nitride nanobarb (BNNB), a new generation nanostructure with unique surface morphology and mechanical “barbs” have been analyzed, understanding these properties is essential for their high-end applications as thermal interface materials (TIM) for microwave, 5G and microelectronic devices. The analysis of the crystallization parameters includes crystallization onset, peak and end temperatures, crystallization half-life and overall crystallinity of PTFE, modified PTFE and their BNNB composites. The results were further analyzed using theoretical models such as the combined Avrami-Ozawa model. It was found that BNNB supports crystallization in the modified PTFE but shows minimal effect on the crystallization of PTFE. Due to the limitation of the classical theoretical models used above in fully characterizing the multi-step crystallization process of PTFE, an in-depth analysis using the model-free advanced isoconversional computation was used to characterize the PTFE crystallization based on the evolution of activation energy with fractional crystallinity and for the first time with temperature. Three kinetic regions were identified in the crystallization mechanism. Here, this study investigated the molecular organization and microstructural evolution of PTFE, modified PTFE and their composites during non-isothermal crystallization using advanced X-ray scattering measurements. An insight into the changes undergone by the material's microstructural units including crystallite size and morphology, lamellar thickness and lamellar interfacial layer thickness, and crystallographic phase dynamics during non-isothermal cooling from the melt, was provided here in this work. The effect of copolymer modification of PTFE and the inclusion of pristine and functionalized BNNB (a thermally conductive and electrically insulating ceramic) are both new investigations that provide valuable knowledge for the development of materials with strong matrix-nanofiller interaction and guidance for optimizing sintering and cooling cycles, two key steps in PTFE processing that largely affect the material microstructural features. Overall, the result of the three-part investigation demonstrates that BNNB supports crystallization in the modified PTFE up to 20 wt% concentration and at low and high cooling rates typically used in the industrial processing of PTFE.

36 MATERIALS SCIENCE↗

Experimental Study of Local Micro-forming for Bi-HTS

The Bi-HTS (BSCCO high temperature superconductor) tape now has become the product in an industrial way, which has been available to apply in electric and electron fields. The main way to manufacture Bi-HTS tape is to use the technique of oxide powder in silver tube (OPIT), which involves the multi-step drawing and rolling with plastic deformation, which obviously belongs to a type of the micro-forming in macro-scale processing. There are two main characteristics founded: (a) contact and friction between silver and BSCCO surfaces, (b) interface between two materials. A series of micro-tensile experiments of silver foil with thicknesses of 0.03, 0.06 and 0.1 mm are designed to investigate the behaviors of silver with various scale of sizes. And the surface topography measurements have been carried out to analyze the changes in surface topography. Based upon experiments, some topics are researched which are referred to inhomogeneous, local effect, size effect, grain and micro-structure affecting, surface roughness, long-distance sausage phenomenon. Further the local breakdown of silver by Bi-HTS powder during process is analyzed through failure criterion. The results of this work will bring out an important exploration value to the theory and computation of micro-forming.

36 MATERIALS SCIENCE↗

Growth, sintering, and chemical states of Co supported on reducible CeO 2 (111) thin films: The effects of the metal coverage and the nature of the support

The growth, sintering, and interaction of cobalt with ceria were studied under ultrahigh vacuum conditions by vapor-deposition of Co onto well-defined CeOx(111) (1.5 < x < 2) thin films grown on Ru(0001). Charge transfer from Co to ceria occurs upon deposition of Co on CeO 1.96 and partially reduced CeO 1.83 at 300 K. X-ray photoelectron spectroscopy studies show that Co is oxidized to Co 2+ species at the cost of the reduction of Ce 4+ to Ce 3+ , at a lesser extent on reduced ceria. Co 2+ is the predominant species on CeO 1.96 at low Co coverages (e.g., ≤0.20 ML). The ratio of metallic Co/Co 2+ increases with the increase in the Co coverage. However, both metallic Co and Co 2+ species are present on CeO 1.83 even at low Co coverages with metallic Co as the major species. Scanning tunneling microscopy results demonstrate that Co tends to wet the CeO 1.96 surface at very low Co coverages at room temperature forming one-atomic layer high structures of Co–O–Ce. The increase in the Co coverage can cause the particle growth into three-dimensional structures. The formation of slightly flatter Co particles was observed on reduced CeO 1.83 . In comparison with other transition metals including Ni, Rh, Pt, and Au, our studies demonstrate that Co on ceria exhibits a smaller particle size and higher thermal stability, likely arising from strong metal–support interactions. The formed particles upon Co deposition at 300 K are present on the ceria surface after heating to 1000 K. The Co–ceria interface can be tuned by varying the Co metal coverage, the annealing temperature, and the nature of the ceria surface.

36 MATERIALS SCIENCE↗

Dislocation mediated alignment during metal nanoparticle coalescence

Dislocation mediated alignment processes during gold nanoparticle coalescence were studied at low and high temperatures using molecular dynamics simulations and transmission electron microscopy. Particles underwent rigid body rotations immediately following attachment in both low temperature (500 K) simulated coalescence events and low temperature (~315 K) transmission electron microscopy beam heating experiments. In many low temperature simulations, some degree of misorientation between particles remained after rigid body rotations, which was accommodated by grain boundary dislocation nodes. These dislocations were either sessile and remained at the interface for the duration of the simulation or dissociated and cross-slipped through the adjacent particles, leading to improved co-alignment. Minimal rigid body rotations were observed during or immediately following attachment in high temperature (1100 K) simulations, which is attributed to enhanced diffusion at the particles' interface. However, rotation was eventually induced by {111} slip on planes parallel to the neck groove. These deformation modes led to the formation of single and multi-fold twins whose structures depended on the initial orientation of the particles. The driving force for {111} slip is attributed to high surface stresses near the intersection of low energy {111} facets in the neck region. The details of this twinning process were examined in detail using simulated trajectories, and the results reveal possible mechanisms for the nucleation and propagation of Shockley partials on consecutive planes. Deformation twinning was also observed in-situ using transmission electron microscopy, which resulted in the co-alignment of a set of the particles' {111} planes across their grain boundary and an increase in their dihedral angle. As a result, this constitutes the first detailed experimental observation of deformation twinning during nanoparticle coalescence, validating simulation results presented here and elsewhere.

36 MATERIALS SCIENCE↗

Ductile-Phase Toughened Tungsten for Plasma Facing Materials (Final Report)

Tungsten (W) and W-alloys are the leading candidates for plasma-facing components in nuclear fusion reactors because of their high melting point, high temperature strength, good thermal conductivity and low sputtering yield, however, they are too brittle to serve a structural function. A variety of processing approaches were employed to fabricate ductile-phase-toughened (DPT) tungsten (W) composites, that includes consolidating elemental W powder with Cu- or WC-coated W-wires via spark plasma sintering (SPS). Laminated W-composites with Cu-foils were also fabricated by hot-pressing or brazing. Mechanical testing and analytical modeling were used to guide composite development. The fracture toughness of thin W plate or laminated W-composites was measured in three-point bending (3PB) at room temperature (RT). Crack arrest and crack bridging were observed for the laminated composites, and fracture resistance curves were successfully calculated. An analytical model of crack bridging was developed using the specimen geometry, matrix properties, and the stress-displacement function of a ductile reinforcement (“bridging law”) to calculate the fracture resistance curve (R-curve) and load-displacement curve (P-D curve) for any test specimen geometry. The code was also implemented to estimate the bridging law of an arbitrary composite using R-curve data. In another approach, commercially available liquid-phase sintered W alloys with four different compositions were characterized in terms of microstructure, tensile and fracture toughness at different specimen, size, geometry and testing temperatures. The room temperature (RT) average maximum load fracture toughness values (KIc or KJm ≈ 38 to 107 MPa√m) of WHA, containing only 3 to 10 wt.% of a NiFe-based ductile phase (DP), are ≈ 5 to 13 times higher than for monolithic W (≈ 8 MPa√m). Most RT tests show extensive stable ductile tearing (DT) at all W contents, including 97W (KJm ≈ 69 MPa√m), for small baseline bend bars (B=1.65mm, W=2B). Exceptions to DT, include RT elastic fracture at 97W observed in 3x larger specimens than the baseline specimens. However, the WHA KIc was still almost 5 times higher than that for monolithic W. The other exception to RT ductile tearing was for some of the 6 to 8x larger 95W alloy specimens that contained large ceramic initiating inclusions at the precrack front, along with lower DP%, with a KIc ≈ 59 MPa√m, compare to their stable DT KJm ≈ 82 MPa√m. Small specimen tests down to -196°C, to partially emulate irradiation hardening, also transition to elastic fracture at a temperature (-150 for 90W to -25ºC for 97W) that depends on the W content. However, even at -196°C, the KIc at 97W is ≈ 3 times that of monolithic W at RT. In contrast to classical ductile phase toughening by macrocrack bridging, WHA toughening mainly involves new mechanisms associated with arrest, blunting and bridging of numerous process zone microcracks. Later, these WHAs were used to fabricate W-WHA hybrid composites by coating elemental W powder on WHA using SPS. Three-point bend bars were fabricated and fracture toughness was tested at room temperature. Crack initiated and propagated from W-part to the WHA part for the well-bonded (interface) W-WHA composites for 90 and 92.5WHAs, however, crack arrested and diverted at/or through the interface for loosely bonded W-95/97WHAs with increasing load.

36 MATERIALS SCIENCE↗

Importance of the Heat Treatment Scheme on Self-Reducing Reactive Silver Inks

Self-reducing reactive silver inks can print high-quality silver at reasonable temperatures. While numerous studies have explored the impact of processing temperature on electrical properties, the role of the heat treatment scheme has not yet been studied. Common heat treatment schemes include printing and drying inks at room temperature before heat treatment, performing heat treatments while the inks are still wet, and directly printing the inks onto heated substrates. Each scheme generates distinct heat transfer and mass transport kinetics that can affect the silver morphology and electrical properties. However, to date, the impact of different schemes has not been systematically investigated. To address this knowledge gap, this work investigates how different heat treatment schemes impact metal formation, sintering, and the resultant electrical properties of printed self-reducing reactive silver inks. Heat treatment on room-temperature dried inks and wet inks, with top-down (oven) and bottom-up (hot plate) heating sources, were compared. Inks dried at room temperature resulted in extremely porous films that required high heat treatment temperatures (>100 °C) for silver densification. However, these dried films could only densify locally, and their high initial porosities resulted in voids and high resistances (~0.6 Ω mm –1 ) even after heat treatments above 300 °C. Inks that were wet during heat treatment showed moderate improvements in electrical properties with resistances on the order of 0.4 Ω mm –1 at heat treatments of 250 °C. Printing reactive inks directly onto heated substrates yielded the best low-temperature results, with 0.46 Ω mm –1 (5.5 × bulk silver) line resistances achieved at only 90 °C. Overall, this work’s experimental results provide detailed insights into why printing onto a heated substrate results in superior electrical performance compared to more common heat treatment schemes. Additionally, controlling where the precipitation reaction occurs is critical to controlling the film morphology and properties. As a result, this work shows that even an ammonia-based silver reactive ink can achieve good, low-temperature electrical properties with the proper heat treatment scheme.

14 SOLAR ENERGY↗