Search NASA⌕ Search

SEARCH · Search NASA

Results for “STABILITY, LATERAL - DYNAMIC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1946

An Estimation of the Flying Qualities of the Kaiser Fleetwing All-Wing Airplane from Tests of a 1/7-Scale Model, TED No. NACA 2340

An investigation of a 1/7-scale powered model of the Kaiser Fleetwing all-wing airplane was made in the Langley full-scale tunnel to provide data for an estimation of the flying qualities of the airplane. The analysis of the stability and control characteristics of the airplane has been made as closely as possible in accordance with the requirements of the Bureau of Aeronautics, Navy Department's specifications, and a summary of the more significant conclusions is presented as follows. With the normal center of gravity located at 20 percent of the mean aerodynamic chord, the airplane will have adequate static longitudinal stability, elevator fixed, for all flight conditions except for low-power operation at low speeds where the stability will be about neutral. There will not be sufficient down-elevator deflection available for trim above speeds of about 130 miles per hour. It is probable that the reduction in the up-elevator deflections required for trim will be accompanied by reduced elevator hinge moments for low-power operation at low flight speeds. The static directional stability for this airplane will be low for all rudder-fixed or rudder-free flight conditions. The maximum rudder deflection of 30 deg will trim only about 15 deg yaw for most flight conditions and only 10 deg yaw for the condition with low power at low speeds. Also, at low powers and low speeds, it is estimated that the rudders will not trim the total adverse yaw resulting from an abrupt aileron roll using maximum aileron deflection. The airplane will meet the requirements for stability and control for asymmetric power operation with one outboard engine inoperative. The airplane would have no tendency for directional divergence but would probably be spirally unstable, with rudders fixed. The static lateral stability of the airplane will probably be about neutral for the high-speed flight conditions and will be only slightly increased for the low-power operation in low-speed flight. The airplane will not roll against the ailerons in a side-slip maneuver. Although the airplane would probably meet the minimum requirements of pb/2V of 0.07 at all speeds, there will be a loss in rolling ability of the airplane at high aileron deflections and at low flight speeds. It is estimated that the wing stall will be a gradual movement forward from the trailing edge and will be accompanied by no sudden pitching or rolling accelerations. Some stall warning may be indicated by reduction in the elevator and aileron force gradients and by the shaking of the controls caused by unsteady flow over the surfaces near the stall.

Brewer, Gerald W.↗
NASA NTRS1981

Experimental and theoretical study of three interacting, closely-spaced, sharp-edged 60 deg delta wings at low speeds

Wind tunnel tests were conducted to determine the subsonic longitudinal aerodynamic characteristics of lifting configuration consisting of a 60 deg delta main wing with two smaller 60 deg delta wings (called sub-wings) attached underneath. The test was designed to determine the effects on lift, drag, and pitching moment due to various placement of the subwings in relation to the main wing. Test results indicate the increasing vertical separation between the main wing and the sub-wings produced the most significant results; a 23.1% increase in maximum lift coefficient, a reduction in drag coefficient at high lift coefficients, and an increase in longitudinal stability. Lateral separation of the sub-wings produced no significant changes. Placement of the sub-wings rearward increases the initial lift curve slope and maximum lift coefficient and also increase the longitudinal stability. Results of a computer study using a vortex lattice code supported the experimental conclusions.

Faery, H. F., Jr.↗
NASA NTRS1999

Preliminary Results of the 1.5% TCA (Modular) Controls Model in the NASA Langley UPWT

To summarize the significant highlights in this report: (1) Data quality, determined by multiple repeat runs performed on the TCA baseline configuration, and long-term repeatability, determined by comparing baseline Reference H data from this test to a previous test, have been shown to be good. (2) The longitudinal stability of the TCA is more non-linear than for the Reference H, and while it is similar at normal lift values, the TCA has considerably more pitch-up at higher lift. (3) Longitudinal control effectiveness of the TCA is similar to the Reference H and the ratio of elevator effectiveness to horizontal tail effectiveness is approximately 0.3. 4) The directional stability of the TCA is improved relative to Reference H at higher angles-of attack. The chine is effective for improving directional stability. (5) The directional control effectiveness 'of the TCA rudder is the same as that of the Reference H rudder at low angles-of-attack, after taking factors, such as number of rudder panels deflected and vertical tail volume into account. However, rudder effectiveness was shown to be reduced at higher angles-of-attack. (6) The lateral stability was shown to be reduced relative to the Reference H, which may be beneficial at low speeds for alleviating lateral control saturation. (7) Lateral control effectiveness for the TCA was shown to be similar to the Reference H for negative trailing-edge flap deflections and was reduced by approximately 25% for positive trailing-edge flap deflections.

Kubiatko, Paul↗
NASA NTRS1945

Flight Measurements of Lateral and Directional Stability and Control Characteristics of the Grumman F8F-1 Airplane

This paper presents the results of flight tests to determine the lateral and directional stability and control characteristics of the Grumman F8F-1 airplane with three vertical-tail configurations. The data presented herein have no bearing on the performance characteristics of the airplane, which were not measured but which were considered to be exceptionally good. The conclusions reached regarding the lateral and directional stability and control characteristics may be summarized as follows: 1. It was found that the directional stability was poor with the production vertical tail. Addition of a 12-inch extension to the vertical fin and rudder produced a desirable improvement in directional stability and control characteristics. However, further enlargement of the vertical tail would be required to make the directional stability satisfactory in all respects. 2. There was a tendency for the rudder control force to overbalance at large angles of right sideslip with the modified vertical tails. There was no such tendency with the production tail configuration which included a dorsal fin. It was concluded that the dorsal fin should have been retained on the modified vertical tails. 3. The aileron control characteristics were better than those of many comparable airplanes which have been tested. However, the ailerons did not satisfy the Navy requirements for satisfactory flying qualities with regard to either control forces or rolling effectiveness. 4. The power of the rudder trimming tab proved to be inadequate and the tab should be enlarged and/or be provided with an increased deflection range.

Crane, H. L.↗
NASA NTRS1974

Maximum likelihood identification of aircraft stability and control derivatives

Application of a generalized identification method to flight test data analysis. The method is based on the maximum likelihood (ML) criterion and includes output error and equation error methods as special cases. Both the linear and nonlinear models with and without process noise are considered. The flight test data from lateral maneuvers of HL-10 and M2/F3 lifting bodies are processed to determine the lateral stability and control derivatives, instrumentation accuracies, and biases. A comparison is made between the results of the output error method and the ML method for M2/F3 data containing gusts. It is shown that better fits to time histories are obtained by using the ML method. The nonlinear model considered corresponds to the longitudinal equations of the X-22 VTOL aircraft. The data are obtained from a computer simulation and contain both process and measurement noise. The applicability of the ML method to nonlinear models with both process and measurement noise is demonstrated.

Mehra, R. K.↗
NASA NTRS1972

A generalized method for the identification of aircraft stability and control derivatives from flight test data.

This paper discusses the application of a generalized identification method for flight test data analysis. The method is based on the maximum likelihood (ML) criterion and includes output error and equation error methods as special cases. Both the linear and nonlinear models with and without process noise are considered. The flight test data from lateral maneuvers of HL-10 and M2/F3 lifting bodies are processed to determine the lateral stability and control derivatives, instrumentation accuracies and biases. A comparison is made between the results of the output error method and the generalized ML method for M2/F3 data containing gusts. It is shown that better fits to time histories are obtained by using the generalized ML method.

Mehra, R. K.↗
NASA NTRS1962

Experimental Research on 4-Duct Tandem VTOL Aircraft Configurations

This paper presents a brief summary of several wind-tunnel investigations conducted at the Langley Research Center of the NASA to study the aerodynamic and stability and control characteristics of several VTOL aircraft configurations powered by four tilting ducted propellers arranged in tandem pairs. Specifically the two rear ducts could be mounted close alongside the upper rear portion of the fuselage with small wing panels attached to the outboard side of the ducts or could be mounted outboard on the tips of a small wing located high on the rear portion of the fuselage. The two front ducts were always mounted close inboard on the forward part of the fuselage and could be mounted either in a high or low position on the fuselage. The results of the investigation indicated that aircraft of this type could have acceptable aerodynamic and static longitudinal and lateral stability and control characteristics in both transition and normal cruise flight except for the possible qualification that the lateral force due to sideslip is abnormally high and might cause the aircraft to be too sensitive to side gusts.

VTOL AIRCRAFT↗
NASA NTRS1960

Aerodynamic Characteristics at Low Speed of a Reentry Configuration Having Rigid Retractable Conical Lifting Surfaces

An exploratory investigation has been made in the Langley 300 MPH 7 by 10 foot tunnel to study the low-speed static longitudinal and lateral stability characteristics of a reentry configuration having rigid retractable conical lifting surfaces that unfolded from the surface of a conical fuselage. The model also had curved tail surfaces that unfolded from a cylindrical aft section attached to the cone. Longitudinal tests were made through an angle-of-attack range from -4 deg to 90 deg and limited lateral tests were made through an angle-of-sideslip range from -12 deg to 32 deg at an angle of attack of 0 deg. The tail surface provided longitudinal trim to maximum lift and beyond and up to an angle of attack of 51 deg for a center-of-moment location of 42.9 percent mean aerodynamic chord. For this center-of-moment position the model had a static margin of 12 percent mean aerodynamic chord at the lower lift coefficients and was longitudinally stable up to a lift coefficient between 1.0 and 1.2. Neutral stability occurred from lift coefficient of 1.0 up to near maximum lift coefficient. The maximum value of trimmed lift-drag ratio was 4.85 at a lift coefficient of approximately 0.3 and a trimmed angle of attack of approximately 10 deg. The configuration was directionally stable throughout the test angle of sideslip range for an angle of attack of 0 deg.

Fournier, Paul G.↗
NASA NTRS1976

Design of a control configured tanker aircraft

The benefits that accrue from using control configured vehicle (CCV) concepts were examined along with the techniques for applying these concepts to an advanced tanker aircraft design. Reduced static stability (RSS) and flutter mode control (FMC) were the two primary CCV concepts used in the design. The CCV tanker was designed to the same mission requirements specified for a conventional tanker design. A seven degree of freedom mathematical model of the flexible aircraft was derived and used to synthesize a lateral stability augmentation system (SAS), a longitudinal control augmentation system (CAS), and a FMC system. Fatigue life and cost analyses followed the control system synthesis, after which a comparative evaluation of the CCV and conventional tankers was made. This comparison indicated that the CCV weight and cost were lower but that, for this design iteration, the CCV fatigue life was shorter. Also, the CCV crew station acceleration was lower, but the acceleration at the boom operator station was higher relative to the corresponding conventional tanker. Comparison of the design processes used in the CCV and conventional design studies revealed that they were basically the same.

Walker, S. A.↗
NASA NTRS1933

Pressure Distribution Tests on a Series of Clark Y Biplane Cellules with Special Reference to Stability

The pressure distribution data discussed in this report represents the results of part of an investigation conducted on the factors affecting the aerodynamic safety of airplanes. The present tests were made on semispan, circular-tipped Clark Y airfoil models mounted in the conventional manner on a separation plane. Pressure readings were made simultaneously at all test orifices at each of 20 angles of attack between -8 degrees and +90 degrees. The results of the tests on each wing arrangement are compared on the bases of maximum normal force coefficient, lateral stability at a low rate of roll, and relative longitudinal stability. Tabular data are also presented giving the center of pressure location of each wing.

Noyes, Richard W↗
NASA NTRS1959

Force-Test Investigation of the Stability and Control Characteristics of a 1/4-Scale Model of a Tilt-Wing Vertical-Take-Off-and-Landing Aircraft

A wind-tunnel investigation has been made to determine the aerodynamic characteristics of a 1/4-scale model of a tilt-wing vertical-take-off-and-landing aircraft. The model had two 3-blade single-rotation propellers with hinged (flapping) blades mounted on the wing, which could be tilted from an incidence of 4 deg for forward flight to 86 deg for hovering flight. The investigation included measurements of both the longitudinal and lateral stability and control characteristics in both the normal forward flight and the transition ranges. Tests in the forward-flight condition were made for several values of thrust coefficient, and tests in the transition condition were made at several values of wing incidence with the power varied to cover a range of flight conditions from forward-acceleration (or climb) conditions to deceleration (or descent) conditions The control effectiveness of the all-movable horizontal tail, the ailerons and the differential propeller pitch control was also determined. The data are presented without analysis.

Newsom, William A., Jr.↗
NASA NTRS1972

Low-speed aerodynamic characteristics of a model having a 42 deg swept low wing with a supercritical airfoil, double-slotted flaps, and a T-tail

A low speed wind tunnel test was conducted in the Langley V/STOL tunnel to determine the static longitudinal and lateral stability characteristics of a general research model which simulated an advance configuration for a commercial transport airplane with a T tail. The model had a 42 deg swept, aspect ratio 6.78 wing with a supercritical airfoil and a high lift system which consisted of a leading edge slat and a double slotted flap. Various slat and flap deflection combinations represented clean, take off, and landing configurations. Effects on the longitudinal and lateral aerodynamic characteristics were determined for two flow through, simulated engine nacelles located on the sides of the fuselage near the rear of the model.

Fournier, P. G.↗
NASA NTRS1958

Low-Speed Static Stability Characteristics of Two Configurations Suitable for Lifting Reentry from Satellite Orbit

An investigation of the low-speed static stability and control characteristics of 1/4-scale models of two configurations suitable for lifting reentry from satellite orbit has been made in the Langley free- flight tunnel. One of the models was a thick, all-wing configuration having a delta plan form and the other was a flat delta wing with a half-cone fuselage. The investigation showed that, in general, the all-wing configuration had better longitudinal and lateral stability characteristics than the flat delta configuration.

Paulson, John W.↗
NASA NTRS1974

Low-speed aerodynamic characteristics of a transport configuration having a 42 deg swept supercritical airfoil wing and three tail height positions

A low speed investigation was conducted in the Langley V/STOL tunnel to define the static stability characteristics of an advanced high subsonic speed transport aircraft model in the cruise configuration (no high lift system). The wing of the model had 42 deg sweep of the quarter chord line, an aspect ratio of 6.78, and supercritical airfoil sections. Three different horizontal tail configurations (high, mid, and low) were investigated on the complete model and for the model with the wing removed in order to assess effects of the wing flow field on the tail contributions to both longitudinal and lateral stability characteristics. All the model configurations investigated were tested over an angle of attack range from approximately -5 to 23 deg. Some model configurations were also tested over an angle of attack range from about 11 to 38 deg in order to explore the aerodynamic characteristics in the deep stall region.

Fournier, P. G.↗
NASA NTRS1987

Partitioning of flight data for aerodynamic modeling of aircraft at high angles of attack

It is sometimes necessary to determine aerodynamic model structure and estimate associated stability and control derivatives for airplanes from flight data that cover a large range of angle of attack or sideslip. One method of dealing with that problem is through data partitioning. The main purpose of this paper is to provide an explanation of a data partitioning procedure and its application and to discuss both the power and limitations of that procedure for the analysis of large maneuvers of aircraft. The partitioning methodology is shown to provide estimates for coefficients of those regressors that are well excited in the aircraft motion. In particular, primary lateral stability and damping derivatives are identified throughout the maneuver ranges.

Batterson, James G.↗
NASA NTRS1993

X-31 aerodynamic characteristics determined from flight data

The lateral aerodynamic characteristics of the X-31 were determined at angles of attack ranging from 20 to 45 deg. Estimates of the lateral stability and control parameters were obtained by applying two parameter estimation techniques, linear regression, and the extended Kalman filter to flight test data. An attempt to apply maximum likelihood to extract parameters from the flight data was also made but failed for the reasons presented. An overview of the System Identification process is given. The overview includes a listing of the more important properties of all three estimation techniques that were applied to the data. A comparison is given of results obtained from flight test data and wind tunnel data for four important lateral parameters. Finally, future research to be conducted in this area is discussed.

Kokolios, Alex↗
NASA NTRS1984

Locally linearized longitudinal and lateral-directional aerodynamic stability and control derivaties for the X-29A aircraft

The locally linearized longitudinal and lateral-directional aerodynamic stability and control derivatives for the X-29A aircraft were calculated for altitudes ranging from sea level to 50,000 ft, Mach numbers from 0.2 to 1.5, and angles of attack from -5 deg to 25 deg. Several other parameters were also calculated, including aerodynamic force and moment coefficients, control face position, normal acceleration, static margin, and reference angle of attack.

Budd, G. D.↗