Search NASA⌕ Search

SEARCH · Search NASA

Results for “Sensor Depth”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

Development of Solid State Thermal Sensors for Aeroshell TPS Flight Applications

In-situ Thermal Protection System (TPS) sensors are required to provide verification by traceability of TPS performance and sizing tools. Traceability will lead to higher fidelity design tools, which in turn will lead to lower design safety margins, and decreased heatshield mass. Decreasing TPS mass will enable certain missions that are not otherwise feasible, and directly increase science payload. NASA Ames is currently developing two flight measurements as essential to advancing the state of TPS traceability for material modeling and aerothermal simulation: heat flux and surface recession (for ablators). The heat flux gage is applicable to both ablators and non-ablators and is therefore the more generalized sensor concept of the two with wider applicability to mission scenarios. This paper describes the continuing development of a thermal microsensor capable of surface and in-depth temperature and heat flux measurements for TPS materials appropriate to Titan, Neptune, and Mars aerocapture, and direct entry. The thermal sensor is a monolithic solid state device composed of thick film platinum RTD on an alumina substrate. Choice of materials and critical dimensions are used to tailor gage response, determined during calibration activities, to specific (forebody vs. aftbody) heating environments. Current design has maximum operating temperature of 1500K, and allowable constant heat flux of q=28.7 W/cm(sup 2), and time constants between 0.05 and 0.2 seconds. The catalytic and radiative response of these heat flux gages can also be changed through the use of appropriate coatings. By using several co-located gages with various surface coatings, data can be obtained to isolate surface heat flux components due to radiation, catalycity and convection. Selectivity to radiative heat flux is a useful feature even for an in-depth gage, as radiative transport may be a significant heat transport mechanism for porous TPS materials in Titan aerocapture.

Martinez, Ed↗
NASA NTRSDate not supplied

Highlights of NASA’s Orbital Debris Program Office In Situ and Laboratory Measurements

NASA’s Orbital Debris Program Office (ODPO) maintains various returned spacecraft materials, capabilities, and facilities used for in situ and laboratory measurements that directly support orbital debris environmental models. In situ measurements include the analysis of exposed and returned hardware surfaces. These surfaces serve as passive sensors for the small-sized micrometeoroid and orbital debris (MMOD) flux below the sensitivity of ground-based radar and optical sensors. Various instruments and techniques are used to determine the size and depth of selected impact features, and – if feasible – the composition of the projectile material. Analysis of the impactor residues enables the differentiation of MM and OD for debris below 1 mm to support modeling the OD environment. In addition, projectiles identified as OD can be further differentiated in low-, medium-, and high- density impactors based on chemical analyses. In addition to in situ measurements, the ODPO has also worked in collaboration with the U.S. Space Force Space Systems Command (formerly the U.S. Air Force Space and Missile Systems Center), the Aerospace Corporation, and the University of Florida on a laboratory-based hypervelocity impact test, DebriSat, conducted at the Air Force Arnold Engineering Development Complex in 2014. The resulting data from this impact test series are being analyzed to assess the fragments’ sizes/masses, materials/densities, shapes, and other parameters of interest. The DebriSat project provides the data needed to update NASA’s breakup models and size estimation models using the simulated orbital breakup of a modern, low Earth orbit spacecraft. Ultimately, over 200,000 fragments from this impact test will be stored at NASA Johnson Space Center (JSC) and further analyzed by the ODPO. This project will also use machine learning techniques to infer physical parameters of fragments embedded in the soft-catch foam used in the impact experiment. Applied to X-ray imagery of the foam panels, these techniques promise to minimize human-in-the-loop processes for fragment extraction and physical characterization. A brief overview of this project and data collected will be presented. Lastly, the ODPO provides various capabilities hosted at NASA JSC for optical inspections and measurements using a variety of techniques and scientific instrumentation to support both in situ and laboratory measurements. The ODPO’s Optical Measurement Center (OMC) is an advanced facility for photometric and spectroscopic laboratory measurements of targets, including fragments from the DebriSat project. The OMC simulates telescopic observations by using space-like illumination conditions and source-target-sensor orientation techniques. Additionally, the OMC is uniquely equipped to acquire pseudo-bidirectional reflectance distribution data for broadband photometric measurements, thus removing aspect angle dependencies that can affect target size estimates using the optical size estimation model. Narrow-band surface material characterization using spectroscopic instrumentation gives insight into how the albedo parameter – also important in the optical size estimation model – may vary depending on the state of the material. The OMC also performs simulations of photometric measurements using optical ray-tracing software to model the OMC optical throughput. In addition to the OMC, the ODPO houses a start-of-the-art Fragment Analysis Facility that uses multiple microscopic inspection instruments to support in situ measurements and material characterization. An overview of both facilities will be highlighted in this paper.

Orbital Debris↗
NASA NTRSDate not supplied

Highlights of NASA’s Orbital Debris Program Office In Situ and Laboratory Measurements

NASA’s Orbital Debris Program Office (ODPO) maintains various returned spacecraft materials, capabilities, and facilities used for in situ and laboratory measurements that directly support orbital debris environmental models. In situ measurements include the analysis of exposed and returned hardware surfaces. These surfaces serve as passive sensors for the small-sized micrometeoroid and orbital debris (MMOD) flux below the sensitivity of ground-based radar and optical sensors. Various instruments and techniques are used to determine the size and depth of selected impact features, and – if feasible – the composition of the projectile material. Analysis of the impactor residues enables the differentiation of MM and OD for debris below 1 mm to support modeling the OD environment. In addition, projectiles identified as OD can be further differentiated in low-, medium-, and high- density impactors based on chemical analyses. In addition to in situ measurements, the ODPO has also worked in collaboration with the U.S. Space Force Space Systems Command (formerly the U.S. Air Force Space and Missile Systems Center), the Aerospace Corporation, and the University of Florida on a laboratory-based hypervelocity impact test, DebriSat, conducted at the Air Force Arnold Engineering Development Complex in 2014. The resulting data from this impact test series are being analyzed to assess the fragments’ sizes/masses, materials/densities, shapes, and other parameters of interest. The DebriSat project provides the data needed to update NASA’s breakup models and size estimation models using the simulated orbital breakup of a modern, low Earth orbit spacecraft. Ultimately, over 200,000 fragments from this impact test will be stored at NASA Johnson Space Center (JSC) and further analyzed by the ODPO. This project will also use machine learning techniques to infer physical parameters of fragments embedded in the soft-catch foam used in the impact experiment. Applied to X-ray imagery of the foam panels, these techniques promise to minimize human-in-the-loop processes for fragment extraction and physical characterization. A brief overview of this project and data collected will be presented. Lastly, the ODPO provides various capabilities hosted at NASA JSC for optical inspections and measurements using a variety of techniques and scientific instrumentation to support both in situ and laboratory measurements. The ODPO’s Optical Measurement Center (OMC) is an advanced facility for photometric and spectroscopic laboratory measurements of targets, including fragments from the DebriSat project. The OMC simulates telescopic observations by using space-like illumination conditions and source-target-sensor orientation techniques. Additionally, the OMC is uniquely equipped to acquire pseudo-bidirectional reflectance distribution data for broadband photometric measurements, thus removing aspect angle dependencies that can affect target size estimates using the optical size estimation model. Narrow-band surface material characterization using spectroscopic instrumentation gives insight into how the albedo parameter – also important in the optical size estimation model – may vary depending on the state of the material. The OMC also performs simulations of photometric measurements using optical ray-tracing software to model the OMC optical throughput. In addition to the OMC, the ODPO houses a start-of-the-art Fragment Analysis Facility that uses multiple microscopic inspection instruments to support in situ measurements and material characterization. An overview of both facilities will be highlighted in this paper.

Orbital Debris↗
NASA NTRS1975

Summary of the Active Microwave Workshop, chapter 1

An overview is given of the utility, feasibility, and advantages of active microwave sensors for a broad range of applications, including aerospace. In many instances, the material provides an in-depth examination of the applicability and/or the technology of microwave remote sensing, and considerable documentation is presented in support of these techniques. An assessment of the relative strengths and weaknesses of active microwave sensor data indicates that satisfactory data are obtainable for several significant applications.

Source record↗
NASA NTRS2016

Elevated Aerosol Layers and Their Radiative Impact over Kanpur During Monsoon Onset Period

Accurate information about aerosol vertical distribution is needed to reduce uncertainties in aerosol radiative forcing and its effect on atmospheric dynamics. The present study deals with synergistic analyses of aerosol vertical distribution and aerosol optical depth (AOD) with meteorological variables using multisatellite and ground-based remote sensors over Kanpur in central Indo-Gangetic Plain (IGP). Micro-Pulse Lidar Network-derived aerosol vertical extinction (sigma) profiles are analyzed to quantify the interannual and daytime variations during monsoon onset period (May-June) for 2009-2011. The mean aerosol profile is broadly categorized into two layers viz., a surface layer (SL) extending up to 1.5 km (where sigma decreased exponentially with height) and an elevated aerosol layer (EAL) extending between 1.5 and 5.5 km. The increase in total columnar aerosol loading is associated with relatively higher increase in contribution from EAL loading than that from SL. The mean contributions of EALs are about 60%, 51%, and 50% to total columnar AOD during 2009, 2010, and 2011, respectively. We observe distinct parabolic EALs during early morning and late evening but uniformly mixed EALs during midday. The interannual and daytime variations of EALs are mainly influenced by long-range transport and convective capacity of the local emissions, respectively. Radiative flux analysis shows that clear-sky incoming solar radiation at surface is reduced with increase in AOD, which indicates significant cooling at surface. Collocated analysis of atmospheric temperature and aerosol loading reveals that increase in AOD not only resulted in surface dimming but also reduced the temperature (approximately 2-3 C) of lower troposphere (below 3 km altitude). Radiative transfer simulations indicate that the reduction of incoming solar radiation at surface is mainly due to increased absorption by EALs (with increase in total AOD). The observed cooling in lower troposphere in high aerosol loading scenario could be understood as a dynamical feedback of EAL-induced stratification of lower troposphere. Further, the observed radiative effect of EALs increases the stability of the lower troposphere, which could modulate the large-scale atmospheric dynamics during monsoon onset period. These findings encourage follow-up studies on the implication of EALs to the Indian summer monsoon dynamics using numerical models.

aerosol vertical distribution↗
NASA NTRS2017

Mars 2020 Entry, Descent, and Landing Instrumentation 2 (MEDLI2) Sensor Suite

The Mars 2020 Entry, Descent, and Landing Instrumentation 2 (MEDLI2) sensor suite seeks to address the aerodynamic, aerothermodynamic, and thermal protection system (TPS) performance issues during atmospheric entry, descent, and landing of the Mars 2020 mission. Based on the highly successful instrumentation suite that flew on Mars Science Laboratory (MEDLI), the new sensor suite expands on the types of measurements and also seeks to answer questions not fully addressed by the previous mission. Sensor Package: MEDLI2 consists of 7 pressure transducers, 17 thermal plugs, 2 heat flux sensors, and one radiometer. The sensors are distributed across both the heatshield and backshell, unlike MEDLI (the first sensor suite), which was located solely on the heat-shield. The sensors will measure supersonic pressure on the forebody, a pressure measurement on the aftbody, near-surface and in-depth temperatures in the heatshield and backshell TPS materials, direct total heat flux on the aftbody, and direct radiative heating on the aftbody. Instrument Development: The supersonic pressure transducers, the direct heat flux sensors, and the radiometer all were tested during the development phase. The status of these sensors, including the piezo-resistive pressure sensors, will be presented. The current plans for qualification and calibration for all of the sensors will also be discussed. Post-Flight Data Analysis: Similar to MEDLI, the estimated flight trajectory will be reconstructed from the data. The aerodynamic parameters that will be reconstructed will be the axial force coefficient, freestream Mach number, base pressure, atmospheric density, and winds. The aerothermal quantities that will be determined are the heatshield and backshell aero-heating, turbulence transition across the heatshield, and TPS in-depth performance of PICA. By directly measuring the radiative and total heat fluxes on the back-shell, the convective portion of the heat flux will be estimated. The status of the current tools to perform the post-flight data analysis will be presented, along with plans for model improvements.

Hwang, Helen H.↗
NASA NTRS2017

Mars 2020 Entry, Descent, and Landing Instrumentation 2 (MEDLI2) Sensor Suite

The Mars 2020 Entry, Descent, and Landing Instrumentation 2 (MEDLI2) sensor suite seeks to address the aerodynamic, aerothermodynamic, and thermal protection system (TPS) performance issues during atmospheric entry, descent, and landing of the Mars 2020 mission. Based on the highly successful instrumentation suite that flew on Mars Science Laboratory (MEDLI), the new sensor suite expands on the types of measurements and also seeks to answer questions not fully addressed by the previous mission. Sensor Package: MEDLI2 consists of 7 pressure transducers, 17 thermal plugs, 2 heat flux sensors, and one radiometer. The sensors are distributed across both the heatshield and backshell, unlike MEDLI (the first sensor suite), which was located solely on the heat-shield. The sensors will measure supersonic pressure on the forebody, a pressure measurement on the aftbody, near-surface and in-depth temperatures in the heatshield and backshell TPS materials, direct total heat flux on the aftbody, and direct radiative heating on the aftbody. Instrument Development: The supersonic pressure transducers, the direct heat flux sensors, and the radiometer all were tested during the development phase. The status of these sensors, including the piezo-resistive pressure sensors, will be presented. The current plans for qualification and calibration for all of the sensors will also be discussed. Post-Flight Data Analysis: Similar to MEDLI, the estimated flight trajectory will be reconstructed from the data. The aerodynamic parameters that will be reconstructed will be the axial force coefficient, freestream Mach number, base pressure, atmospheric density, and winds. The aerothermal quantities that will be determined are the heatshield and backshell aero-heating, turbulence transition across the heatshield, and TPS in-depth performance of PICA. By directly measuring the radiative and total heat fluxes on the back-shell, the convective portion of the heat flux will be estimated. The status of the current tools to perform the post-flight data analysis will be presented, along with plans for model improvements.

Hwang, Helen↗
NASA NTRS1982

Applications of remote sensing to geobotanical prospecting for non-renewable resources

Airborne sensors used in the remote detection of geobotanical anomalies are able to locate mineral deposits. Geobotanical stress is manifested in increased visible spectrum reflectance due to a decrease in chlorophyll content which induces chlorosis. The effectiveness of this method is, however, restricted to soils in which plant root structures are embedded in bedrock-derived soils to a depth sufficient for the production of heavy metal stress. It is noted that Landsat remote sensors are inherently better suited to the detection of overall plant density or biomass changes relating to zones of mineralization.

Birnie, R. W.↗
DOE OSTI2019

Utah FORGE: Well 58-32 Stimulation Conference Paper and Data

The U.S. Department of Energy’s (U.S. DOE) Frontier Observatory for Research in Geothermal Energy (FORGE) is a field laboratory that provides a unique opportunity to develop and test new technologies for characterizing, creating and sustaining Enhanced Geothermal Systems (EGS) in a controlled environment. In 2018, the U.S. DOE selected a site in south-central Utah for the FORGE laboratory. Numerous geoscientific studies have been conducted in the region since the 1970s in support of geothermal development at Roosevelt Hot Springs. A vertical scientific well, 58-32, was drilled and tested to a depth of 2290 m (7515 ft) GL in 2017 on the FORGE site to provide additional characterization of the reservoir rocks. The well encountered a conductive thermal regime and a bottom hole temperature of 199degC (390degF). More than 2000 natural fractures were identified, but measured permeabilities are low, less than 30 micro-darcies. Induced fractures indicate that the maximum horizontal stress trends NNE-SSW, consistent with geologic and well observations from the surrounding area. Approximately 45 m (147 ft) at the base of the well was left uncased. A maximum wellhead pressure of 27.6 MPa (4000 psig) at an injection rate of ~1431 L/min (~9 bpm) was measured during stimulation testing in September 2017. Conventional diagnostic evaluations of the data suggest that hydraulic fracturing and shearing occurred. Estimates of the stress gradient for delta_h_min range from of 16.7 to 17.6 kPa/m (0.74 to 0.78 psi/ft). A gradient of 25.6 kPa/m (1.13psi/ft) was calculated for delta_V. In 2019, the 2017 open-hole stimulation in well 58-32 was repeated with injection rates up to 2385 L/min (15 bpm). Two additional stimulations were conducted in the cased portion of the well; one to stimulate critically stressed fractures and the second to test noncritically stressed fractures. Breakdown of the zone spanning critically-stressed fractures occurred at a surface pressure of approximately 29.0 MPa (4200 psig). Although stimulation of the noncritically stressed fractures was interrupted by failure of the bridge plug beneath the perforated interval, micro-seismic data suggests stimulation of the fractures may have been initiated at a surface pressure of 45.5 MPa (6600 psig). These stimulation results support the conclusion the Mineral Mountains granitoid is an appropriate host for EGS development. Micro-seismicity was monitored during the stimulations using surface and downhole instrumentation. Five seismometers and a nodal array of 150 seismic sensors were deployed on the surface. A Distributed Acoustic Sensing (DAS) cable and a string of 12 geophones were deployed in well 78-32, drilled to a depth of 998 m (3274 ft) GL. A broadband sensor and a high-temperature geophone were deployed in well 68-32, drilled to a depth of 303 m (994 ft) GL. More than 420 micro-seismic events were detected by the geophone string. Other instruments detected fewer events.

15 GEOTHERMAL ENERGY↗
NASA NTRS1975

The use of lasers for hydrographic studies

The utilization of remote laser sensors in water pollution detection and identification, coastal environmental monitoring, and bathymetric depth sounding, is discussed. qr

Kim, H. H.↗
NASA NTRS1980

Soil moisture sensing with microwave techniques

Microwave approaches for the remote sensing of soil moisture are discussed, with the advantages described as follows: (1) the all-weather capability, (2) the greater penetration depth into the soil and through vegetation than with optical or infrared sensors, and (3) the large changes in the dielectric properties of soil produced by changes in water content. Both active and passive microwave approaches are discussed. The dependence of the relationship between microwave response and soil moisture on such things as soil texture, surface roughness, vegetative cover and nonuniform moisture and temperature profiles is analyzed from both the experimental and theoretical viewpoints. The dielectric properties of the soil are analyzed quantitatively, as these control the reflective and emissive properties of the soil surface, and a model for estimating a soil's dielectric properties from its texture and moisture content is also presented. Emissivity is calculated using the Fresnel equation of electromagnetic theory, and reflectivity is shown to be decreased by surface roughness, while the backscatter coefficient increases. It is demonstrated, that microwave radiometers are sensitive to soil moisture for a wide range of surface conditions, and that the longer wavelengths are best for soil moisture sensing.

Schmugge, T.↗
NASA NTRS1983

Direct determination of surface albedos from satellite imagery

An empirical method to measure the spectral surface albedo of surfaces from Landsat imagery is presented and analyzed. The empiricism in the method is due only to the fact that three parameters of the solution must be determined for each spectral photograph of an image on the basis of independently known albedos at three points. The approach is otherwise based on exact solutions of the radiative transfer equation for upwelling intensity. Application of the method allows the routine construction of spectral albedo maps from satelite imagery, without requiring detailed knowledge of the atmospheric aerosol content, as long as the optical depth is less than 0.75, and of the calibration of the satellite sensor.

Mekler, Y.↗
NASA NTRS1985

LANDSAT-4 Thematic Mapper Calibration and Atmospheric Correction

The LANDSAT-4 thematic mapper, with its wide spectral coverage and digitization to 8 bits per word, is a large step forward in the direction of quantitative radiometry from the multispectral scanner (MSS). In order to utilize the quantitative accuracy built into the thematic mapper effectively, more attention must be paid to calibration before launch, changes of calibration with time in orbit, and atmospheric interference with the measurements, especially in the 450 to 520 nanometer band. Experience with the coastal zone color scanner (CZCS) program led to procedures wherein Rayleigh correction factors can be generated utilizing simultaneous surface truth data that empirically give correct upwelled surface radiances, despite errors in sensor calibration, solar spectral irradiance measurements, and reported values of Rayleigh optical depth. These techniques offer sensitive tests for change in calibration, especially at shorter wavelengths. Instruments, such as the CZCS, have shown that calibration changes first, and to the largest degree, at the shorter wavelengths, with lesser changes as wavelength increases. These techniques are utilized to calculate a Rayleigh correction factor that, together with geometric terms, should give an accurate correction for this portion of the atmospheric contribution to the signal.

Hovis, W. A.↗
NASA NTRS2006

Moving water to South America as observed from space

The approximate balance of the mass change rate measured by the Gravity Recovery and Climate Experiment (GRACE) with the moisture influx across the entire coastline less climatological river discharge for South America (SA), in agreement with the conservation principle, bolsters not only the credibility of the spacebased measurements, but supports the characterization of ocean's influence on the annual variation of continental water balance. The moisture transport integrated over the depth of the atmosphere is estimated using measurements by QuikSCAT and Special Sensor Microwave/Imager. The large-scale geographic patterns of precipitation from the Tropical Rain Measuring Mission (TRMM) and the mass change rate were found to follow similar annual changes over South America.

monsoon↗
NASA NTRS2005

SAFER Inspection of Space Shuttle Thermal Protection System

In the aftermath of the space shuttle Columbia accident, it quickly became clear that new methods would need to be developed that would provide the capability to inspect and repair the shuttle's thermal protection system (TPS). A boom extension to the Remote Manipulator System (RMS) with a laser topography sensor package was identified as the primary means for measuring the damage depth in acreage tile as well as scanning Reinforced Carbon- Carbon (RCC) surfaces. However, concern over the system's fault tolerance made it prudent to investigate alternate means of acquiring close range photographs and contour depth measurements in the event of a failure. One method that was identified early was to use the Simplified Aid For EVA Rescue (SAFER) propulsion system to allow EVA access to damaged areas of concern. Several issues were identified as potential hazards to SAFER use for this operation. First, the ability of an astronaut to maintain controlled flight depends upon efficient technique and hardware reliability. If either of these is insufficient during flight operations, a safety tether must be used to rescue the crewmember. This operation can jeopardize the integrity of the Extra-vehicular Mobility Unit (EMU) or delicate TPS materials. Controls were developed to prevent the likelihood of requiring a tether rescue, and procedures were written to maximize the chances for success if it cannot be avoided. Crewmember ability to manage tether cable tension during nominal flight also had to be evaluated to ensure it would not negatively affect propellant consumption. Second, although propellant consumption, flight control, orbital dynamics, and flight complexity can all be accurately evaluated in Virtual Reality (VR) Laboratory at Johnson Space Center, there are some shortcomings. As a crewmember's hand is extended to simulate measurement of tile damage, it will pass through the vehicle without resistance. In reality, this force will push the crewmember away from the vehicle, and could induce a moment which, if strong enough, could saturate the attitude control system in SAFER. This raises the concern that additional propellant will be consumed to maintain controlled flight. To account for this, the fidelity of the Virtual Reality simulation was improved to include the effect of crewmember contact with the vehicle during SAFER flight. In addition, while participating in VR simulations, the subject is in shirt sleeves and sits in a chair. This does not provide a flight-like representation of body position awareness. To prevent inadvertent contact with tile or RCC, other facilities were utilized to establish crew preferences for body attitude and tool configuration. Finally, a study was performed to determine if attitude constraints are needed for the Space shuttle and International Space Station to reduce SAFER flight difficulty.

Scoville, Zebulon C.↗
NASA NTRS2023

Pacific Northwest Health & Air Quality: Monitoring Trends in Air Quality During a Drought Case Study to Improve Public Health Response to Drought Threats

Recent studies have documented a correlation between air quality and drought in the United States, which has been linked with increased aerosols including airborne particulate matter (PM) during drought conditions. This study partnered with local health departments to evaluate trends in air quality in the Pacific Northwest during the evolution of drought conditions using aerosol optical depth (AOD) observations collected by NASA’s Moderate Resolution Imaging Spectroradiometer (MODIS) sensor aboard the Terra and Aqua satellites. These satellite data were analyzed in conjunction with ground-based PM2.5 and PM10 data sourced from the Environmental Protection Agency (EPA)’s network of ground-based monitors and the Standardized Precipitation Evapotranspiration Index (SPEI) drought index. Based on recommendations by local health departments, this study examined air quality trends between 2015 and 2022 in 12 counties within Oregon and Washington that reflected diversity in population density, drought exposure, rural and urban status, and data availability from EPA monitors. Overall, results indicated variation in relationships among drought, satellite, and ground-based air quality data across the study area. This study did not control for the impact of wildfire events on air quality and also did not investigate shorter SPEI aggregation periods, both of which are avenues for future research. This project supplemented research into links between drought and human health and provided health departments with an objective foundation from which they can communicate public health risks to local communities.

Abby Sgan↗
NASA NTRSDate not supplied

Monitoring Trends in Air Quality During a Drought: Case Study to Improve Public Health Response to Drought Threats

Drought has been an area of distinct concern in the Pacific Northwest since the mid-2010s. Recent studies have documented a correlation between air quality and drought in the United States, which is often observed in increased aerosols including airborne particulate matter (PM). This study partnered with the Oregon Health Authority and Washington State Department of Health to evaluate trends in air quality in the Pacific Northwest during the evolution of drought conditions using aerosol optical depth (AOD) observations collected by NASA’s Moderate Resolution Imaging Spectroradiometer (MODIS) sensor aboard the Terra and Aqua satellites. These satellite data were analyzed in conjunction with ground-based PM2.5 and PM10 data sourced from the Environmental Protection Agency (EPA) Air Quality System’s network of ground-based monitors and the Standardized Precipitation Evapotranspiration Index drought index. Based on recommendations by local health departments, this study examined air quality trends between 2015 and 2022 in 12 counties within Oregon and Washington that reflected diversity in population density, drought exposure, rural and urban status, and data availability from EPA AQS monitors. The findings from this study provided supplemental information to the ongoing efforts by community health stakeholders to study the public health impacts of drought and support public health responses to future drought events.

Taylor West↗