Search NASA⌕ Search

SEARCH · Search NASA

Results for “Shocks”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Post-shock spikes - A new feature of proton and alpha enhancements associated with an interplanetary shock wave

Description of the salient characteristics of temporal variations of greater than or about equal to 100 keV/nucleon protons and alpha particles during a ten-hour period associated with the passage of an interplanetary shock wave. In addition to extending measurements to energies considerably below previous observations for energetic storm particle and shock-spike events, the discovery of a new low energy feature, referred to as 'postshock spikes', is reported. The typical width of these spikes is several minutes, but they occur several hours after the passage of the shock front. Evidence is presented that spikes depends on the energy per charge of the particles.

Gloeckler, G.↗

Incident shock-wave characteristics in air, argon, carbon dioxide, and helium in a shock tube with unheated helium driver

Incident shock-wave velocities were measured in the Langley 6-inch expansion tube, operated as a shock tube, with air, argon, carbon dioxide, and helium as test gases. Unheated helium was used as the driver gas and most data were obtained at pressures of approximately 34 and 54 MN/sq m. A range of pressure ratio across the diaphragm was obtained by varying the quiescent test-gas pressure, for a given driver pressure, from 0.0276 to 34.5 kN/sq m. Single- and double-diaphragm modes of operation were employed and diaphragms of various materials tested. Shock velocity was determined from microwave interferometer measurements, response of pressure transducers positioned along interferometer measurements, response of pressure transducers positioned along the driven section (time-of-arrival gages), and to a lesser extent, measured tube-wall pressure. Velocities obtained from these methods are compared and limitations of the methods discussed. The present results are compared with theory and the effects of diaphragm mode (single or double diaphragm), diaphragm material, heating of the driver gas upon pressurization of the driver section, diaphragm opening time, interface mixing, and two-dimensional (nonplanar) flow are discussed.

Miller, C. G., III↗

Table and charts of equilibrium normal shock and shock tube properties for pure argon with velocities to 18 km/sec

Equilibrium thermodynamic and flow properties are presented in tabulated and graphical form for moving, standing, and reflected normal shock waves in pure argon. Properties include pressure, temperature, density, enthalpy, speed of sound, entropy, molecular-weight ratio, isentropic exponent, velocity, and species mole fractions. Incident (moving) shock velocities are varied from 2 to 18 km/sec for a range of initial pressure of 5 N/sq m to 500 kN/sq m. Working charts illustrating shock tube performance with argon test gas and heated helium and hydrogen driver gases are also presented.

Miller, C. G., III↗

Molecule formation and infrared emission in fast interstellar shocks. II - Dissociation speeds for interstellar shock waves

The postshock destruction of molecules is examined, including the processes of (1) collisions with neutral hydrogen atoms and molecules, (2) electronic collisions, and (3) neutral chemical reactions with atoms, particularly atomic hydrogen. By using conservative estimates of collisional dissociation rates from individual vibrational states, it is found that process (1) leads to the destruction of molecular hydrogen behind shocks with speeds equal to or greater than 25 km/s if the preshock molecular gas has hydrogen nucleus densities of equal to or greater than 10 to the 4th/cu cm. At lower densities (100 per cu cm), destruction occurs for shock speeds equal to or greater than 50 km/s and process (2) dominates. Dissociation of molecules such as CO, H2O, and O2 follows the destruction of H2, as the resultant hydrogen atoms chemically dissociate the metal atoms from their bonds (process 3) in the hot postshock gas. These results demonstrate that many of the observed high-speed interstellar molecules, if shock accelerated, must have dissociated and reformed in the postshock gas.

Hollenbach, D.↗

The cosmic-ray shock structure problem for relativistic shocks

The time asymptotic behaviour of a relativistic (parallel) shock wave significantly modified by the diffusive acceleration of cosmic-rays is investigated by means of relativistic hydrodynamical equations for both the cosmic-rays and thermal gas. The form of the shock structure equation and the dispersion relation for both long and short wavelength waves in the system are obtained. The dependence of the shock acceleration efficiency on the upstream fluid spped, long wavelength Mach number and the ratio N = P sub co/cP sub co+P sub go)(Psub co and P sub go are the upstream cosmic-ray and thermal gas pressures respectively) are studied.

Webb, G. M.↗

Cosmic-ray shock acceleration in oblique MHD shocks

A one-dimensional, steady-state hydrodynamical model of cosmic-ray acceleration at oblique MHD shocks is presented. Upstream of the shock the incoming thermal plasma is subject to the adverse pressure gradient of the accelerated particles, the J x B force, as well as the thermal gas pressure gradient. The efficiency of the acceleration of cosmic-rays at the shock as a function of the upstream magnetic field obliquity and upstream plasma beta is investigated. Astrophysical applications of the results are briefly discussed.

Webb, G. M.↗

Non-linear shipboard shock analysis of the Tomahawk missile shock isolation system

The identification, quantification, computer modeling and verification of the Tomahawk nonlinear liquid spring shock isolation system in a surface ship Vertical Launch System (VLS) are discussed. The isolation system hardware and mode of operation is detailed in an effort to understand the nonlinearities. These nonlinearities are then quantified and modeled using the MSC/NASTRAN finite element code. The model was verified using experimental data from the Navel Ordnance Systems Center MIL-S-901 medium weight shock tests of August 1986. The model was then used to predict the Tomahawk response to the CG-53 USS Mobile Bay shock trials of May-June 1987. Results indicate that the model is an accurate mathematical representation of the physical system either functioning as designed or in an impaired condition due to spring failure.

Leifer, Joel↗

Viscous hypersonic shock-on-shock interaction on blunt cowl lips

The effects of impinging ramp shocks on a two-dimensional viscous inlet cowl of the National Aerospace Plane (NASP) or blunt body flow fields for various impingement locations are numerically simulated by a recently developed second-order implicit total variation diminishing (TVD) algorithm. The results demonstrate that accurate computation of heat transfer rate is crucially dependent on adequate normal grid resolution at the wall. The various numerical results are compared with recent experimental data. Due to the complex flow patterns that occur for the shock-on-shock flows, adaptive grid procedures are utilized.

Klopfer, G. H.↗

Shock temperatures in silica glass - Implications for modes of shock-induced deformation, phase transformation, and melting with pressure

Observations of shock-induced radiative thermal emissions are used to determine the gray body temperatures and emittances of silica glass under shock compression between 10 and 30 GPa. The results suggest that fused quartz deforms heterogeneously in this shock pressure range. It is shown that the 10-16 GPa range coincides with the permanent densification region, while the 16-30 GPa range coincides with the inferred mixed phase region along the silica glass Hugoniot. Low emittances in the mixed phase region are thought to represent the melting temperature of the high-pressure phase, stishovite. Also, consideration is given to the effects of pressure on melting relations for the system SiO2-Mg2SiO4.

Schmitt, Douglas R.↗

Fast molecular shocks. I - Reformation of molecules behind a dissociative shock

The physical and chemical processes that operate in the cooling gas behind a fast, dissociative, single-fluid shock propagating in a dense interstellar cloud are discussed. The treatment extends previous theoretical work on fast molecular shocks by including the effects of the conversion of Ly-alpha photons into radiation of the two-photon continuum and into H2 Lyman band emission lines, the effects of CO photodissociation following line absorption, and the formation and destruction of molecules containing the elements nitrogen, silicon, and sulphur, and of the complex hydrocarbons. Abundance profiles for the molecular species of interest are presented. After molecular hydrogen begins to reform, by means of gas phase and grain surface processes, the neutral species OH, H2O, O2, CO, CN, HCN, N2, NO, SO, and SiO reach substantial abundances. The molecular ions HeH(+), OH(+), SO(+), CH(+), H2(+), and H3(+), are produced while the gas is still hot and partially ionized. Emissions from them provide a possible diagnostic probe of fast molecular shocks.

Neufeld, David A.↗

Effects of nose bluntness and shock-shock interactions on blunt bodies in viscous hypersonic flows

A numerical study was conducted to investigate the effects of blunt leading edges on the viscous flow field around a hypersonic vehicle such as the proposed National Aero-Space Plane. Attention is focused on two specific regions of the flow field. In the first region, effects of nose bluntness on the forebody flow field are investigated. The second region of the flow considered is around the leading edges of the scramjet inlet. In this region, the interaction of the forebody shock with the shock produced by the blunt leading edges of the inlet compression surfaces is analyzed. Analysis of these flow regions is required to accurately predict the overall flow field as well as to get necessary information on localized zones of high pressure and intense heating. The results for the forebody flow field are discussed first, followed by the results for the shock interaction in the inlet leading edge region.

Singh, D. J.↗

An analysis of combustion studies in shock expansion tunnels and reflected shock tunnels

The effect of initial nonequilibrium dissociated air constituents on the combustion of hydrogen in high-speed flows for a simulated Mach 17 flight condition was investigated by analyzing the results of comparative combustion experiments performed in a reflected shock tunnel test gas and in a shock expansion tunnel test gas. The results were analyzed and interpreted with a one-dimensional quasi-three-stream combustor code that includes finite rate combustion chemistry. The results of this study indicate that the combustion process is kinetically controlled in the experiments in both tunnels and the presence of the nonequilibrium partially dissociated oxygen in the reflected shock tunnel enhances the combustion. Methods of compensating for the effect of dissociated oxygen are discussed.

Jachimowski, Casimir J.↗

Laminar and turbulent flow computations of Type 4 shock-shock interference aerothermal loads using unstructured grids

This report presents computations for the Type 4 shock-shock interference flow under laminar and turbulent conditions using unstructured grids. Mesh adaptation was accomplished by remeshing, refinement, and mesh movement. Two two-equation turbulence models were used to analyze turbulent flows. The mean flow governing equations and the turbulence governing equations are solved in a coupled manner. The solution algorithm and the details pertaining to its implementation on unstructured grids are described. Computations were performed at two different freestream Reynolds numbers at a freestream Mach number of 11. Effects of the variation in the impinging shock location are studied. The comparison of the results in terms of wall heat flux and wall pressure distributions is presented.

Vemaganti, Gururaja R.↗

A Nonlinear Theory for Predicting the Effects of Unsteady Laminar, Turbulent, or Transitional Boundary Layers on the Attenuation of Shock Waves in a Shock Tube with Experimental Comparison

The linearized attenuation theory of NACA Technical Note 3375 is modified in the following manner: (a) an unsteady compressible local skin-friction coefficient is employed rather than the equivalent steady-flow incompressible coefficient; (b) a nonlinear approach is used to permit application of the theory to large attenuations; and (c) transition effects are considered. Curves are presented for predicting attenuation for a shock pressure ratio up to 20 and a range of shock-tube Reynolds numbers. Comparison of theory and experimental data for shock-wave strengths between 1.5 and 10 over a wide range of Reynolds numbers shows good agreement with the nonlinear theory evaluated for a transition Reynolds number of 2.5 X 10(exp 5).

Trimpi, Robert L.↗

Detailed Simulations of Shock-Bifurcation and Ignition of an Argon-diluted Hydrogen/Oxygen Mixture in a Shock Tube

Detailed simulations of the bifurcation and ignition of an Argon-diluted Hydrogen/Oxygen mixture in the two-stage weak ignition regime are performed. An adaptive mesh-refinement (AMR) technique is employed to resolve all relevant physical scales that are associated with the viscous boundary-layer, the reaction front, and the shock-wave. A high-order hybrid WENO/central-differencing method is used as spatial discretization scheme, and a detailed chemical mechanism is employed to describe the combustion of the H2/O2 mixture. The operating conditions considered in this study are p = 5 bar and T = 1100 K, and fall in the third explosion limit. The computations show that the mixing of the thermally stratified fluid, carrying different momentum and enthalpy, introduces inhomogeneities in the core-region behind the reflected shock. These inhomogeneities act as localized ignition kernels. During the induction period, these kernels slowly expand and eventually transition to a detonation wave that rapidly consumes the unburned mixture.In competition with this detonation wave are the presence of secondary ignition kernels that appear in the unreacted core-region between reflected shock and detonation wave.

Ihme, Matthias↗

Direct Monte Carlo Simulations of Chemical Equilibrium Composition of Molecular Fluid Mixtures Under Shock Conditions

A new Monte Carlo simulation method is implemented which holds the number and kind of atoms constant rather than the number and kind of molecules for a molecular fluid mixture. Chemical reactions are allowed as a correlated move of atoms such as an interchange of atoms between molecules. Equilibrium chemical composition is determined as an average over the simulation along with equation of state quantities. Results are presented for N 2 + O 2 → 2NO at 30GPa and 3000K. The equilibrium composition is shown to be sensitive to the potentials between unlike species.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Shock tube measurements of high temperature rate constants for OH with cycloalkanes and methylcycloalkanes

High temperature experiments were performed with the reflected shock tube technique using multi-pass absorption spectrometric detection of OH radicals at 308 nm. The present experiments span a wide T-range, 801-1347 K, and represent the first direct measurements of the title rate constants at T>500 K for cyclopentane and cyclohexane and the only high temperature measurements for the corresponding methyl derivatives. The present work utilized 48 optical passes corresponding to a total path length {proportional_to}4.2 m. As a result of this increased path length, the high [OH] detection sensitivity permitted unambiguous analyses for measuring the title rate constants. The experimental rate constants in units, cm{sup 3} molecule{sup -1} s{sup -1}, can be expressed in Arrhenius form as k{sub OH+Cyclopentane}=(1.90{+-}0.30) x 10{sup -10}exp(-1705{+-}56 K/T) (813-1341 K), k{sub OH+Cyclohexane}=(1.86{+-}0.24) x 10{sup -10}exp(-1513{+-}123 K/T) (801-1347 K), k{sub OH+Methylcyclopentane}=(2.02{+-}0.19) x 10{sup -10}exp(-1799{+-}96 K/T) (859-1344 K), k{sub OH+Methylcyclohexane}=(2.55{+-}0.30) x 10{sup -10}exp(-1824{+-}114 K/T) (836-1273 K). These results and lower-T experimental data were used to obtain three parameter evaluations of the experimental rate constants for the title reactions over an even wider T-range. These experimental three parameter fits to the rate constants in units, cm{sup 3} molecule{sup -1} s{sup -1}, are k{sub OH+Cyclopentane}=1.390 x 10{sup -16}T{sup 1.779}exp(97 K/T)cm{sup 3} molecule{sup -1}s{sup -1} (209-1341 K), k{sub OH+Cyclohexane}=3.169 x 10{sup -16}T{sup 1.679}exp(119 K/T)cm{sup 3}molecule{sup -1}s{sup -1} (225-1347 K), k{sub OH+Methylcyclopentane}=6.903 x 10{sup -18}T{sup 2.148}exp(536 K/T)cm{sup 3}molecule{sup -1}s{sup -1} (296-1344 K), k{sub OH+Methylcyclohexane}=2.341 x 10{sup -18}T{sup 2.325}exp(602 K/T)cm{sup 3}molecule{sup -1}s{sup -1} (296-1273 K). High level electronic structure methods were used to characterize the first three reactions in order to provide reliable extrapolations of the rate constants from 250-2000 K. The results of the theoretical predictions for OH + cyclohexane and OH + methylcyclopentane were sufficient to make a theoretical prediction for OH + methylcyclohexane. The present recommended rate expressions for OH with cyclohexane, and methylcyclohexane, give rate constants that are 15-25% higher (over the T-range 800-1300 K) than the rate constants utilized in recent modeling efforts aimed at addressing the oxidation of cyclohexane and methylcyclohexane. The current measurements reduce the uncertainties in rate constants for the primary cycloalkane consumption channel in a high temperature oxidation environment. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

X-ray diffraction from shock driven Sn microjets

Here, in situ x-ray diffraction was performed on shock-generated microjets composed of Sn and Sn–4Ag. Under low pressure drives (~21 GPa), a significant fraction of the jet volume was found to be in the β-Sn phase, and these crystallites were much smaller than the initial grain size of the material. Significant quantities of amorphous (molten) material were observed for higher drive pressures (~25–35 GPa). The extent of melting at these pressures was greater than would be predicted for uniaxial shock loading. Diffraction patterns from the Sn–4Ag alloy showed a peak that is consistent with the expected Ag 3 Sn intermetallic phase. This peak remained evident under drive conditions where the sample was otherwise fully amorphous. This indicates a slushy or a mixed phase of liquid Sn and solid Ag 3 Sn. Given the eutectic character of this alloy, this observation is attributed to a kinetic limitation on the dissolution of Ag 3 Sn. This implies that a much broader range of drive conditions will lead to mixed phase jets and ejecta than would be predicted from the equilibrium melt boundary of such alloys.

36 MATERIALS SCIENCE↗