Search NASA⌕ Search

SEARCH · Search NASA

Results for “Static pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

The Turbulent Pressure Spectrum Within the Roughness Sublayer of a Subarctic Forest Canopy

The turbulent static pressure spectrum E pp (k x ) as a function of longitudinal wavenumber k x in the roughness sublayer of forested canopies is of interest to a plethora of problems such as pressure transport in the turbulent kinetic energy budget, pressure pumping from snow or forest floor, and coupling between flow within and above canopies. Long term static pressure measurements above a sub-arctic forested canopy for near-neutral conditions during the winter and spring were collected and analyzed for three snow cover conditions: trees and ground covered with snow, trees are snow free but the ground is covered with snow, and snow free cover. In all three cases, it is shown that E pp (k x ) obeys the attached eddy hypothesis at low wavenumbers (1/δ < k x < 1/z) —with E pp (k x ) ∝ u$^4_*$k$^{-1}_x$ and Kolmogorov scaling in the inertial subrange at higher wavenumbers—with E pp (k x ) ∝ ϵ 4/3 k x -7/3 , where u * is the friction velocity at the canopy top, is the mean turbulent kinetic energy dissipation rate, z is the distance from the snow top, and is the boundary layer depth. The implications of these two scaling laws to the normalized root-mean squared pressure C p = o p /u$^2_*$ and its newly proposed logarithmic scaling with normalized wall-normal distance z/δ are discussed for snow covered and snow free vegetation conditions. The work here also shows that k$^{-1}_x$ the in the E pp (k x ) appears more extensive and robust than its longitudinal velocity counterpart.

Aslan, Toprak [Finnish Meteorological Inst., Helsi↗
NASA NTRS1975

Ambient and induced pressure fluctuations in supersonic jet flows

An experimental investigation of the ambient static pressure fluctuations and induced acoustic fields in supersonic jet flows has been undertaken to identify possible noise sources and the mechanisms involved in the propagation of disturbances within the flows. The axisymmetric cold air jet under investigation exhausted from a 7-in. exit diameter C-D nozzle run in two conditions: one yielding a fully expanded flow and the other an overexpanded flow. The survey of static pressure fluctuations consisted of measurements of the overall levels and spectra of the fluctuations along the centerline of the two flows and the variation in level across various transverse sections. The second aspect of the study involved the development of a procedure for tracing the propagation of externally induced periodic pressure disturbances inside the jet.

Barra, V.↗
NASA NTRS2000

Heat Transfer and Pressure Distributions on a Gas Turbine Blade Tip

Heat transfer coefficient and static pressure distributions are experimentally investigated on a gas turbine blade tip in a five-bladed stationary linear cascade. The blade is a 2-dimensional model of a first stage gas turbine rotor blade with a blade tip profile of a GE-E(sup 3) aircraft gas turbine engine rotor blade. The flow condition in the test cascade corresponds to an overall pressure ratio of 1.32 and exit Reynolds number based on axial chord of 1.1 x 10(exp 6). The middle 3-blade has a variable tip gap clearance. All measurements are made at three different tip gap clearances of about 1%, 1.5%, and 2.5% of the blade span. Heat transfer measurements are also made at two different turbulence intensity levels of 6.1 % and 9.7% at the cascade inlet. Static pressure measurements are made in the mid-span and the near-tip regions as well as on the shroud surface, opposite the blade tip surface. Detailed heat transfer coefficient distributions on the plane tip surface are measured using a transient liquid crystal technique. Results show various regions of high and low heat transfer coefficient on the tip surface. Tip clearance has a significant influence on local tip beat transfer coefficient distribution. Heat transfer coefficient also increases about 15-20% along the leakage flow path at higher turbulence intensity level of 9.7% over 6.1 %.

Azad, Gm S.↗
NASA NTRS2020

Calibration of the 11x11-Foot Transonic Wind Tunnel at NASA Ames Research Center

A static pipe calibration characterizing the streamwise static pressure distribution was conducted at the 11-By 11-Foot Transonic Wind Tunnel at NASA Ames Research Center. This data is used to determine the local Mach number within the test section and evaluate buoyancy corrections to axial force measurements. The 60 foot long, 6 inch diameter pipe contained 444 static pressure taps spanning the test section and nozzle regions of the tunnel. The forward end of the pipe extends into the settling chamber and is held by four cables mounting to the tunnel shell, and the aft end is fixed on the institutional model support system. A hydraulic cylinder at the aft end of the pipe provides tension on the system to reduce vibration and to keep the pipe as level as possible throughout the test section. The previous calibration was improved upon by using pressure scanners with greater accuracy, ensuring a uniform pressure tube length for each tap to control pneumatic lag, optically tracking any streamwise movement of the pipe, and more tightly controlling the tunnel condition set points. Typically this calibration is conducted with the pipe on tunnel centerline and 33 inches below centerline for sting-mounted models and semi-span (i.e. floor-mounted) models respectively, however schedule demands permitted only the centerline calibration. The semi-span calibration is planned to be completed in the summer of 2020. Immediately following the static pipe calibration, a shorter, 9 foot static pipe used as the calibration check standard was installed to obtain its first post-calibration pressure dataset. This short static pipe consists of 148 static pressure taps distributed along the pipe section and one total pressure tap at the end of an ogive nose. Performing the calibration test and its check standard back-to-back allows this dataset to establish a reliable baseline for future calibration check standard testing. Over time the use of a calibration check standard offers the ability to assess the stability of the calibration through statistical process control in an efficient and costeffective manner, thereby potentially increasing the time required between full tunnel calibrations.

White, Bethany↗
NASA NTRS1983

Shock noise features using the SCIPVIS code

The numerical computational supersonic jet plume model SCIPVIS was analyzed in order to determine its effectiveness for predicting the complicated flow structure associated with supersonic shock containing jet plumes. The analysis focused on assessing the applicability of using this code for predicting the broadband shock noise radiation. The analysis was carried out for several exit Mach number cases (including 1.00, 1.41, and 1.99) covering both underexpanded and overexpanded flow conditions. The three primary turbulence closure models incorporated in the SCIPVIS code were utilized for comparisons to measured plume static pressure distributions. Among other results, the prediction of plume static pressures for all three nozzle exit Mach numbers was found to perform exceptionally well when compared with experimental data for both underexpanded and overexpanded cases. Computations performed using this code for calculating the average shock wavelength for the 1.99 exit Mach number case were shown to provide an excellent prediction of the peak frequency for broadband shock noise. The spatial variation of the turbulent kinetic energy was found to be in qualitative agreement with wedge hot-film measurements.

Seiner, J. M.↗
NASA NTRS1992

A computational study of advanced exhaust system transition ducts with experimental validation

The current study is an application of CFD to a 'real' design and analysis environment. A subsonic, three-dimensional parabolized Navier-Stokes (PNS) code is used to construct stall margin design charts for optimum-length advanced exhaust systems' circular-to-rectangular transition ducts. Computer code validation has been conducted to examine the capability of wall static pressure predictions. The comparison of measured and computed wall static pressures indicates a reasonable accuracy of the PNS computer code results. Computations have also been conducted on 15 transition ducts, three area ratios, and five aspect ratios. The three area ratios investigated are constant area ratio of unity, moderate contracting area ratio of 0.8, and highly contracting area ratio of 0.5. The degree of mean flow acceleration is identified as a dominant parameter in establishing the minimum duct length requirement. The effect of increasing aspect ratio in the minimum length transition duct is to increase the length requirement, as well as to increase the mass-averaged total pressure losses. The design guidelines constructed from this investigation may aid in the design and manufacture of advanced exhaust systems for modern fighter aircraft.

Wu, C.↗
NASA NTRS2015

LEWICE3D/GlennHT Particle Analysis of the Honeywell Al502 Low Pressure Compressor

A flow and ice particle trajectory analysis was performed for the booster of the Honeywell AL502 engine. The analysis focused on two closely related conditions one of which produced a rollback and another which did not rollback during testing in the Propulsion Systems Lab at NASA Glenn Research Center. The flow analysis was generated using the NASA Glenn GlennHT flow solver and the particle analysis was generated using the NASA Glenn LEWICE3D v3.56 ice accretion software. The flow and particle analysis used a 3D steady flow, mixing plane approach to model the transport of flow and particles through the engine. The inflow conditions for the rollback case were: airspeed, 145 ms; static pressure, 33,373 Pa; static temperature, 253.3 K. The inflow conditions for the non-roll-back case were: airspeed, 153 ms; static pressure, 34,252 Pa; static temperature, 260.1 K. Both cases were subjected to an ice particle cloud with a median volume diameter of 24 microns, an ice water content of 2.0 gm3 and a relative humidity of 100 percent. The most significant difference between the rollback and non-rollback conditions was the inflow static temperature which was 6.8 K higher for the non-rollback case.

Ice Accretion Codes↗
NASA NTRS2008

Effects of a Rotating Aerodynamic Probe on the Flow Field of a Compressor Rotor

An investigation of distortions of the rotor exit flow field caused by an aerodynamic probe mounted in the rotor is described in this paper. A rotor total pressure Kiel probe, mounted on the rotor hub and extending up to the mid-span radius of a rotor blade channel, generates a wake that forms additional flow blockage. Three types of high-response aerodynamic probes were used to investigate the distorted flow field behind the rotor. These probes were: a split-fiber thermo-anemometric probe to measure velocity and flow direction, a total pressure probe, and a disk probe for in-flow static pressure measurement. The signals acquired from these high-response probes were reduced using an ensemble averaging method based on a once per rotor revolution signal. The rotor ensemble averages were combined to construct contour plots for each rotor channel of the rotor tested. In order to quantify the rotor probe effects, the contour plots for each individual rotor blade passage were averaged into a single value. The distribution of these average values along the rotor circumference is a measure of changes in the rotor exit flow field due to the presence of a probe in the rotor. These distributions were generated for axial flow velocity and for static pressure.

Lepicovsky, Jan↗
NASA NTRS1971

An investigation of transient pressure and plasma properties in a pinched plasma column

The transient pinched plasma column generated in a linear Z-pinch was studied experimentally and analytically. The plasma column was investigated experimentally with the following plasma diagnostics: a special rapid response pressure transducer, a magnetic field probe, a voltage probe and discharge luminosity. Axial pressure profiles on the discharge chamber axis were used to identify three characteristic regions of plasma column behavior; they were in temporal sequence: strong axial pressure asymmetry noted early in plasma column lifetime followed by plasma heating in which there is a rapid rise in static pressure and a slight decrease static pressure before plasma column breakup. Plasma column lifetime was approximately 5 microseconds. The axial pressure asymmetry was attributed to nonsimultaneous pinching of the imploding current sheet along the discharge chamber axis. The rapid heating is attributed in part to viscous effects introduced by radial gradients in the axial streaming velocity. Turbulent heating arising from discharge current excitation of the ion acoustic wave instability is also considered a possible heating mechanism.

Stover, E. K.↗
NASA NTRS1972

Flow conditions around the exit and downstream of certain stator blading with various trailing edge thicknesses and geometries

The blading investigated was curved back with thick profiles. The variations in flow conditions considered were flow angle and isentropic energy. Experimental data were obtained in a two-dimensional cascade from surveys with a combined angle, total-, and static-pressure probe and from an array of end-wall static pressure taps. Analytical results were obtained from ideal flow theory. The results showed large variations in flow conditions close to the plane of the trailing edge that were largely attenuated at a distance a little greater than one blade pitch downstream of the trailing edge in the direction of flow. The results were affected by the geometry and thickness of the trailing edge. The agreement between experimental and analytical results is generally fair to excellent.

Prust, H. W., Jr.↗
NASA NTRS1991

Wind tunnel blockage study of a generic three-dimensional sidewall compression scramjet inlet at Mach 10

A large scale model of a generic three-dimensional sidewall compression scramjet inlet has been designed based on the results of a computational parametric study for testing in the 31-inch Mach 10 Hypersonic Wind Tunnel at the NASA Langley Research Center. In order to increase the instrumentation density in interaction regions for a highly instrumented model, it is desirable to make the model as large as possible. When the cross-sectional area of a model becomes large relative to the inviscid core size of the tunnel, the effects of blockage must be considered. In order to assess these effects, a blockage model (an inexpensive, much less densely instrumented version of the configuration) was fabricated for preliminary testing. Since it was desired to determine both the effect of the model on the performance of the wind tunnel and also to determine if the inlet would start, the model possessed a total of 32 static pressure orifices distributed on the forebody plane and sidewalls; seventeen static pressure orifices on the tunnel wall and 3 pitot probes on the model monitored the tunnel performance. This paper presents the design considerations in the development of the wind tunnel model and the blockage aspects of the effects of contraction ratio, cowl location, Reynolds number, and angle of attack.

Holland, Scott D.↗
NASA NTRS1992

An experimental investigation of the flow in a diffusing S-duct

Compressible, subsonic flow through a diffusing S-duct has been experimentally investigated. Benchmark aerodynamic data are presented for flow through a representative S-duct configuration. The collected data would be beneficial to aircraft inlet designers and is suitable for the validation of computational codes. Measurements of the 3D velocity field and total and static pressures were obtained at five cross-sectional planes. Surface static pressures and flow visualization also helped to reveal flowfield characteristics. All reported tests were conducted with an inlet centerline Mach number of 0.6 and a Reynolds number, based on the inlet centerline velocity and duct inlet diameter, of 2.6 x 10 exp 6. The results show that a large region of streamwise flow separation occurred within the duct. Transverse velocity components indicate that the duct curvature induces strong pressure driven secondary flows, which evolve into a large pair of counter-rotating vortices. These vortices convect the low momentum fluid of the boundary layer toward the center of the duct, degrading both the uniformity and magnitude of the total pressure profile.

Wellborn, S. R.↗
NASA NTRS1992

An experimental investigation of the flow in a diffusing S-duct

Compressible, subsonic flow through a diffusing S-duct has been experimentally investigated. Benchmark aerodynamic data are presented for flow through a representative S-duct configuration. The collected data would be beneficial to aircraft inlet designers and is suitable for the validation of computational codes. Measurements of the 3D velocity field and total and static pressures were obtained at five cross-sectional planes. Surface static pressures and flow visualization also helped to reveal flow field characteristics. All reported tests were conducted with an inlet centerline Mach number of 0.6 and a Reynolds number, based on the inlet centerline velocity and duct inlet diameter, of 2.6 x 10(exp 6). The results show that a larger region of streamwise flow separation occurred within the duct. Details about the separated flow region, including mechanisms which drive this complicated flow phenomenon, are discussed. Transverse velocity components indicate that the duct curvature induces strong pressure driven secondary flows, which evolve into a large pair of counter-rotating vortices. These vortices convect the low momentum fluid of the boundary layer towards the center of the duct, degrading both the uniformity and magnitude of the total pressure profile.

Wellborn, Steven R.↗
NASA NTRS1997

Thrust Enhancement in Hypervelocity Nozzles by Chemical Catalysis

In the hypersonic flight regime, the air-breathing supersonic combustion ramjet (scramjet) has been shown to be a viable propulsion system. The current designs of scramjet engines provide performance benefits only up to a Mach number of 14. Performance losses increase rapidly as the Mach number increases. To extend the applicability of scram'jets beyond Mach 14, research is being conducted in the area of inlet and wave drag reduction, skin-friction and heat-transfer reduction, nozzle loss minimization, low-loss mixing, and combustion enhancement. For high Mach number applications, hydrogen is the obvious fuel choice because of its high energy content per unit mass in comparison with conventional fuels. These flight conditions require engines to operate at supersonic internal velocities, high combustor temperatures, and low static pressures. The high static temperature condition enhances the production of radicals such as H and OH, and the low-pressure condition slows the reaction rates, particularly the recombination reactions. High-temperature and low-pressure constraints, in combination with a small residence time, result in a radical-rich exhaust gas mixture exiting the combustor. At high Mach number conditions (due to low residence time), H and OH do not have enough time to recombine ; thus, a significant amount of energy is lost as these high-energy free radical are exhausted. The objective of the present study is to conduct a flowfield analysis for a typical nozzle geometry for NASP-type vehicle to assess for thrust enhancement in hypervelocity nozzles by substituting small amount of phosphine for hydrogen.

Singh, D. J.↗
DOE OSTI2022

UAE6 - Wind Tunnel Tests Data - UAE6 - Sequence 4 - Raw Data

Sequence 4: Static Pressure Calibration (P) This test sequence used a downwind, teetered turbine with a 3.4° cone angle. The wind speed ranged from 5 m/s to 25 m/s. Yaw angles of 0° to 30° were achieved. The blade tip pitch was 3°. The rotor rotated at 72 RPM. Blade and probe pressure measurements were collected. A static pitot probe was installed on a boom 2.3 m upwind of the nacelle at hub height and connected to the reference side of the Mensor digital differential pressure transducer through the pneumatic rotary coupling. This provided the reference pressure for all blade-mounted pressure transducers, as opposed to the NASA atmospheric pressure reference that was used for all other test sequences. This simulates the pressure system connections used in field measurements where the static pressure was unknown.

17 WIND ENERGY↗
NASA NTRS1951

Boundary Layer Effect on the Surface Pressure of an Infinite Cone in Supersonic Flow

The theory of Taylor and Maccoll (Ref,1) gives the surface pressure on an infinite cone in supersonic flow as a function of the cone vertex angle and the free stream Mach number and static pressure for a gas of vanishing viscosity. When a slender conical probe is used together with an impact pressure probe to determine the static pressure and Mach number in a low density gas stream, it is desirable to have some theoretical estimate of the effect of viscous boundary layer on the probe readings. Theoretical and experimental results with respect to impact probes have been presented in Refs. 5 and 6. A simple approximation for a conical probe based on linearized supersonic flow and compressible boundary layer theory is presented here.

Lin, T. C.↗
NASA NTRS1987

Reduction of Orifice-Induced Pressure Errors

Use of porous-plug orifice reduces or eliminates errors, induced by orifice itself, in measuring static pressure on airfoil surface in wind-tunnel experiments. Piece of sintered metal press-fitted into static-pressure orifice so it matches surface contour of model. Porous material reduces orifice-induced pressure error associated with conventional orifice of same or smaller diameter. Also reduces or eliminates additional errors in pressure measurement caused by orifice imperfections. Provides more accurate measurements in regions with very thin boundary layers.

Plentovich, Elizabeth B.↗