Search NASA⌕ Search

SEARCH · Search NASA

Results for “Steel manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Evaluation of Composite Structural Materials for Heliostat Cost Reduction

Structures manufactured from steel comprise up to 40% of a CSP heliostat's cost. Composite structures represent a potential opportunity to reduce this cost. A reference heliostat structural model has been created with a reflector area of 25m 2 . The design, constructed of low-carbon steel, pro-vides baseline deflection and stiffness under a 21 m/s operating wind speeds. Wind loads on the tracker structure are determined for both operating and stow conditions. An established roster of suitable metal alternative materials is considered including: glass, basalt, and carbon reinforced polymer (GFRP, BFRP, and CFRP respectively). Three heliostat components are investigated: the pylon, torque tube, and the purlin-strut assembly. Composite material properties are substituted for those of steel, and the beams are re-sized to match the original steel components' deflection under given wind loads. Weight and cost changes resulting from this resizing are evaluated. It is found that GFRP and BFRP represent a 3X–6X cost premium for the same operating deflection character-istics as steel across all three investigated component classes; with weight reduction only achieved for the purlin-strut assembly. While CFRP components can achieve approximately 25–75% weight savings depending on the application, this comes with a 9X–14X cost increase over the steel base-line for tube-type structures and roughly 5X cost increase when replacing c-channel structures. This work does not rule out the possibility of cost savings when the heliostat design and kinematics to take advantage of composites' specific properties.

14 SOLAR ENERGY↗
DOE OSTI2023

Outlook on Industrial Requirements for Incorporating Nuclear Energy into Industrial Processes

There is an increasing interest globally and in the U.S. in decarbonizing heavy industrial processes which have large demands for heat and power. Currently these industries primarily use fossil fuels to meet these demands and they include: oil & gas, petroleum refining, chemicals and derivative products manufacturing, iron & steel production, polymers, ammonia and fertilizers, etc. The U.S. DOE Integrated Energy Systems (IES) program seeks to identify and analyze opportunities for integrating and substituting nuclear energy to fulfil these large heat and power demands in a cost competitive and sustainable manner while reducing carbon emissions of the processes by using clean nuclear power. Presently various representatives from a subset of these industrial companies have expressed interest in evaluating the options of integrating future advanced nuclear small modular reactors with their industries. This study is a scoping study to provide an outlook of industrial energy demands and the potential nuclear energy substitution potential. Future work will analyze in a more detailed manner the potential designs for coupling advanced nuclear reactors with various industries. The industrial processes of oil refining, methanol production, pulp and paper, ammonia and chlorine-alkali are described focusing on how heat and power is used within the facilities in the context of identifying nuclear substitution opportunities. The aim is to provide reliable, competitive, and sustainable energy that is clean while reducing carbon emissions and other environmental impacts such as water withdrawals, consumption, and contamination.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Additive Manufacturing of Fe-based Alloys for Nuclear Reactor Environments

This report is a Milestone 2 deliverable in FY2025, under work package MT-25AN090211 to support research and qualification activities supported by the Advanced Materials and Manufacturing Technologies (AMMT) program. It provides an update on the work done on the laser based additive manufacturing of steels for nuclear applications, conducted collaboratively by Argonne National Laboratory and Pacific Northwestern National Laboratory. Building upon FY23 and FY24 efforts, the focus of FY25 includes continued optimization of process parameters for the alloys: A709 & G92. The work package also includes fabricating test samples to conduct a thorough microstructural analysis and perform preliminary mechanical testing. The major accomplishments of this work package are summarized below, applicable to both Laser Powder Bed Fusion (LPBF) processes conducted at Argonne National Laboratory and Laser Powder Directed Energy Deposition (LP-DED) processes conducted at Pacific Northwest National Laboratory.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Compositional Homogeneity in Rapidly Solidified 316L stainless steel produced by laser powder-bed fusion processing

The segregation of alloying elements in rapidly solidified 316L stainless steel produced using additive manufacturing technologies is widely reported throughout literature. The microstructure of thin walls manufactured from 316L stainless steel using laser powder bed fusion are examined for the presence of alloy segregation, i.e. the rejection of solutes to grain boundaries. Metallographic methods including mechanical polishing and chemical etching are used to prepare samples for microanalysis m

Jankowski, Alan F. [Sandia National Laboratories (↗
DOE OSTI2023

Fiber-Optic Raman Probe for On-line EAF Slag Analysis

Here, in Electric Arc Furnace (EAF) steelmaking, the push for improved efficiency requires accurate analysis of the chemical composition of its slag system to control slag foaming, provide refractory protection, and maintain high furnace iron yield. Therefore, the ability to obtain real-time slag chemistry data would provide a useful tool to improve the control and efficiency of the process. The work reported here aims to assess the structure and chemistry of EAF slags at high temperatures using a portable fiber-optic Raman probe. As a result, the ability to relate Raman spectra peaks to chemistry and structure is demonstrated in experimental result with EAF slags at 1550°C.

47 OTHER INSTRUMENTATION↗
NASA NTRS1921

Crippling Strength of Axially Loaded Rods

A new empirical formula was developed that holds good for any length and any material of a rod, and agrees well with the results of extensive strength tests. To facilitate calculations, three tables are included, giving the crippling load for solid and hollow sectioned wooden rods of different thickness and length, as well as for steel tubes manufactured according to the standards of Army Air Services Inspection. Further, a graphical method of calculation of the breaking load is derived in which a single curve is employed for determination of the allowable fiber stress. Finally, the theory is discussed of the elastic curve for a rod subject to compression, according to which no deflection occurs, and the apparent contradiction of this conclusion by test results is attributed to the fact that the rods under test are not perfectly straight, or that the wall thickness and the material are not uniform. Under the assumption of an eccentric rod having a slight initial bend according to a sine curve, a simple formula for the deflection is derived, which shows a surprising agreement with test results. From this a further formula is derived for the determination of the allowable load on an eccentric rod. The resulting relations are made clearer by means of a graphical representation of the relation of the moments of the outer and inner forces to the deflection.

Natalis, FR↗
NASA NTRSDate not supplied

Developments of Bosch Process Architectures for ISRU Terrestrial Applications

To effectively realize NASA’s goals of a sustainable presence on the Moon and be-yond, In-Situ Resource Utilization (ISRU) must be leveraged. To reduce launch mass for space missions, commodities such as oxygen and carbon can be produced in-situ. Oxygen can be used for life support and as a propellant, and carbon can be used for battery production, filtration, additive manufacturing, and steel casting. Carbon is a required reactant in the carbothermal reduction process, a leading candidate for oxygen production on the lunar surface. To pro-duce these consumables, the Carbon Utilization Technology for Lunar and Atmospheric Systems (CUTLAS) project is developing architectures that leverage the Bosch process. The Bosch process re-acts CO 2 and H 2 to produce carbon powder and water, which can then be electrolyzed, leaving O 2 and recycled H 2 . This process is also applicable to carbon dioxide emissions on Earth.

Carbon capture↗
DOE OSTI2025

Oxide Dispersion Strengthened Ferritic Steel Wire Feedstock Development for Larger Format Additive Manufacturing (CRADA Final Report)

This CRADA project funded through DOE’s INFUSE program sought to demonstrate the viability of fabricating large, complex parts from oxide dispersion strengthened (ODS) steel with advanced manufacturing. Exhibiting excellent radiation tolerance and high mechanical performance at elevated temperatures, ODS steel is a promising structural material candidate for near-plasma components in fusion energy systems. Its use, however, has been limited by a lack of manufacturability. This project sought to produce ODS steel wire through a solid-state shear assisted extrusion process and then demonstrate that the wire can undergo controlled local melting while being welded with the final part sufficiently retaining the beneficial properties of ODS steel. This would allow the use of wire-arc additive manufacturing (WAAM) to manufacture large-scale ODS parts, even though ODS is currently only available as a powder. WAAM is a promising technique for producing components like the replaceable ARC vacuum vessel in CFS’ fusion reactor design. Meanwhile, this project will also expand PNNL’s capability in producing custom wire feedstock with friction extrusion, enabling downstream large-scale manufacturing with WAAM and solid-state based additive manufacturing. The project achieved its goals of developing tooling and fixturing to produce ODS wire at smaller diameters than previous projects. Several small lengths of wire of 1.5 mm and 2.5 mm diameter in the range of 2.5-30 mm long were produced at tool temperatures that are known to cause ODS particle coarsening (~1200 °C). Fixtures and tooling for longer (>1 m) wires were developed but further process development is needed reduce tool temperature during extrusions and to increase wire length needed for WAAM testing and development.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Dynamic properties of 316l stainless steel repaired using electron beam additive manufacturing

Additive manufacturing has the potential to be used for repair of high-value parts, but the strength and integrity of such repaired parts, especially under dynamic loading, in still unknown. This work presents the results of high strain-rate dynamic testing of additively repaired stainless steel samples. The 316L samples were intentionally damaged and subsequently repaired with 308L stainless steel wire using electron beam additive manufacturing. The repaired samples were subjected to gas-gun impact testing to induce incipient damage and determine the role played by the repaired region in dictating damage and failure. The results show the following: 1) the equation of state of the repaired region is comparable to the original material as shown by the unchanged spall plane location, 2) the deformation behavior is similar to the original material as shown by the similar Hugoniot Elastic limit, 3) the spall strength of the repaired region is slightly higher than the original material due to varying grain size, and 4) the damage morphology in the repaired region is different and involves a high rate of void coalescence. In conclusion, despite these minor differences in the spall strength and the damage morphology, the overall dynamic response of the original material and repaired samples is similar suggesting that AM is a promising approach for repairing high-value components.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Oxide Dispersion Strengthened Ferritic Steel Wire Feedstock Development for Large Format Additive Manufacturing - CRADA 620 (Abstract)

This CRADA project funded through DOE’s INFUSE program seeks to demonstrate the viability of fabricating large, complex parts from oxide dispersion strengthened (ODS) steel with advanced manufacturing. Exhibiting excellent radiation tolerance and high mechanical performance at elevated temperatures, ODS steel is a promising structural material candidate for near-plasma components in fusion energy systems. Its use, however, has been limited by a lack of manufacturability. This project will seek to produce ODS steel wire through a solid-state shear assisted extrusion process and then demonstrate that the wire can undergo controlled local melting while being welded with the final part sufficiently retaining the beneficial properties of ODS steel. This would allow the use of wire-arc additive manufacturing (WAAM) to manufacture large-scale ODS parts, even though ODS is currently only available as a powder. WAAM is a promising technique for producing components like the replaceable ARC vacuum vessel in CFS’ fusion reactor design. Meanwhile, this project will also expand PNNL’s capability in producing custom wire feedstock with friction extrusion, enabling downstream large-scale manufacturing with WAAM and solid-state based additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructural and Hall–Petch Analysis of Additively Manufactured Ferritic Alloy Using 2507 Duplex Stainless Steel Powder

The powder bed fusion–laser beam (PBF-LB) process, a method of additive manufacturing (AM), was used to print duplex stainless steel (DSS) using commercial-grade 2507 powders. While conventionally processed DSS has a two-phase microstructure consisting of 50% austenite and 50% ferrite, the PBF-LB-printed 2507 alloy was nearly 100% ferrite. Optimal processing conditions that minimized porosity were determined to be 290 W laser power and 1000 mm/s scan speed, and grain size, texture, and phases were characterized as a function of laser power and scan speed. Grain size increased with increasing laser power but decreased with increasing scan speed. A <100> texture diminished with increasing scan speed from 1000 mm/s to 1400 mm/s. No austenite phase was detected. Transmission electron microscopy (TEM) and scanning transmission electron microscopy (STEM) characterization revealed nanoscale chromium nitride precipitates in the ferritic matrix (incoherent hexagonal close-packed (HCP) precipitates at grain boundaries and coherent body-centered cubic (BCC) precipitates within the grains) and a high density of tangled dislocations. Tensile tests of as-printed alloys showed a yield strength of 570 MPa, an ultimate tensile strength of 756 MPa, and an elongation to failure of 10%. The tensile properties were analyzed based on the observed microstructure considering grain size, nanoscale precipitates, and the high density of dislocations.

Crystallography↗
DOE OSTI2026

Hydrogen-based ore-to-part manufacturing of near-net-shape stainless steel

Decarbonizing iron and steelmaking, combined with global disruptions to raw material supply chains, necessitates novel approaches to iron and steel production. In this work, we demonstrate a direct ore-to-part manufacturing route using a mixture of ore-derived oxide powders of Fe 2 O 3 , Cr 2 O 3 , NiO, and MoO 3 as feedstock for additive manufacturing, combined with sintering under H 2 to produce a near-net-shape austenitic stainless-steel. Complete reduction of all constituent oxides, including MoO 3 and Cr 2 O 3 , is achieved in-situ at 1300 °C, resulting in dense, crack-free bulk alloy. The fabricated part retains geometric fidelity while undergoing substantial volumetric shrinkage inherent to redox and sintering. Thermodynamic calculations elucidate the co-reduction mechanisms and alloying pathways that enable complete metallization. This work is the first demonstration of net-shaping metal parts directly from ore derived oxides, and this ore-to-part approach can minimize the emissions and lead time for manufacturing associated with downstream processing such as rolling, forging, and machining.

Yang, Mingzhang [Univ. of Waterloo, ON (Canada); F↗
DOE OSTI2022

Design of an additively manufactured functionally graded material of 316 stainless steel and Ti-6Al-4V with Ni-20Cr, Cr, and V intermediate compositions

This study presents a method for designing a computationally informed gradient pathway to fabricate a functionally graded material (FGM) with terminal alloys of 316 stainless steel (SS316) and Ti-6Al-4V via directed energy deposition additive manufacturing with powder feedstock. In this work, the grading is accomplished through the introduction of intermediate elements and alloys (Ni-20Cr, Cr, and V) to avoid the brittle Fe-Ti intermetallic phases that form in the direct liquid phase joining of Ti-alloys and stainless steels. Using a combination of equilibrium calculations and Scheil-Gulliver simulations, a compositional pathway was designed to avoid deleterious phases. FGM samples were fabricated and experimentally characterized to determine the viability of the pathway. A change in phases from fcc to bcc was predicted to occur within the Ni-20Cr/Cr gradient region, and this was validated through experimental characterization. No detrimental phases (intermetallic, Laves, or σ phases) formed along the gradient path, demonstrating a successful computationally-informed design and fabrication of an FGM from SS316 to Ti-6Al-4V.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Mitigation of Cu-Induced Grain Boundary Sensitization in Steel Wire Rods Through a Desensitization Heat Treatment

Steel wire rods are essential for manufacturing high-strength steel tire cords. Yet, the presence of residual copper (Cu) in recycled steel can cause grain-boundary sensitization, embrittlement, and deterioration of the mechanical performance of the final product. This study introduces a desensitization heat treatment step designed to redistribute Cu away from austenite grain boundaries after sensitization occurs. The treatment consists of a 10 min dwell at 1000 °C in a 5%H 2 -Ar reducing atmosphere followed by quench. The temperature and hold time were selected based on diffusion calculations to promote solid-state back diffusion of Cu without altering grain morphology. Experimental validation showed that the dwell step reduced the length of Cu-rich sensitized zones of steel wire rod samples containing 0.21 wt.% Cu by approximately 89% and restored the mechanical properties to nearly 95–98% relative to low-Cu baseline steel (0.01 wt.% Cu). Compared with sensitized and as-obtained samples, these results highlight the effectiveness of the proposed method in improving both the microstructure and tensile performance of recycled steel wire rods, enabling their potential application in tire manufacturing.

copper↗
DOE OSTI2025

Post-build stress-relief optimization for laser powder bed fusion 316H stainless steel

Nuclear energy remains a critical component of a diversified and efficient energy portfolio, offering reliable, high-capacity, and low-carbon power. However, in the U.S., aging infrastructure and the slow qualification and deployment of advanced materials and manufacturing techniques hinder progress in next-generation reactor technologies. This study explores the application of laser powder bed fusion (LPBF) additive manufacturing for stainless steel 316H, with a focus on optimizing post-build heat treatments to enhance material properties for high-temperature nuclear applications. The research targets the optimization of stress-relief temperatures to alleviate postbuild residual stresses, ensuring improvements in the microstructural corelated properties. A series of microstructural and mechanical evaluations were performed on LPBF-printed SS-316H samples which were subjected to annealing at temperatures varying between 650 °C and 850 °C. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy analyses revealed that increasing the heattreatment temperature accelerated dislocation recovery. Vickers microhardness measurements showed an initial reduction in values, followed by stabilization over extended durations at all the temperatures. While higher temperatures facilitated faster recovery, they also promoted carbide precipitation along grain and solidification cell boundaries, narrowing the safe processing window. In contrast, heat treatment at 650°C preserved the cellular substructure and enabled controlled carbide precipitation over time. In conclusion, these findings highlight the importance of time–temperature optimization and suggest that 650°C for up to 2 h provides the most favorable balance between recovery and carbide control for a stress-relief treatment.

316 stainless steel↗