Search NASA⌕ Search

SEARCH · Search NASA

Results for “Structural performance prediction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Design and Analysis of the Rocket Experiment Demonstration of a Soft X-Ray (REDSoX) Polarimeter Mirror Module Assembly

The Rocket Experiment Demonstration of a Soft X-ray (REDSoX) Polarimeter is a NASA sounding rocket experiment that is designed to demonstrate the technology necessary for measuring linear X-ray polarization as a function of energy below 1 keV. In astrophysics, soft X-ray spectropolarimetry will be used to probe the nature of acceleration mechanisms in quasar jets and to test models of neutron star structure. NASA Marshall Space Flight Center (MSFC) has designed a grazing-incidence mirror module assembly (MMA) for the REDSoX payload and used Finite Element Modelling Software (ANSYS) to perform structural analysis of the design. In this paper we will describe the overall design of the REDSoX MMA, details of the analysis techniques used for predicting factor of safety in the mirror adhesive bonds and structural components, the buckling analysis of the outer housing, and the raytrace technique used to estimate the effect of gravity sag on optical performance during ground testing.

Structural Analysis↗
NASA NTRS1994

Prediction of R-curves from small coupon tests

R-curves were predicted for Alclad 2024-T3 and C188-T3 sheet using the results of small-coupon Kahn tear tests in combination with two-dimensional elastic-plastic finite element stress analyses. The predictions were compared to experimental R-curves from 6.3, 16 and 60-inch wide M(T) specimens and good agreement was obtained. The method is an inexpensive alternative to wide panel testing for characterizing the fracture toughness of damage-tolerant sheet alloys. The usefulness of this approach was demonstrated by performing residual strength calculations for a two-bay crack in a representative fuselage structure. C188-T3 was predicted to have a 24 percent higher load carrying capability than 2024-T3 in this application as a result of its superior fracture toughness.

Yeh, J. R.↗
NASA NTRS1984

An emulator for minimizing computer resources for finite element analysis

A computer code, SCOPE, has been developed for predicting the computer resources required for a given analysis code, computer hardware, and structural problem. The cost of running the code is a small fraction (about 3 percent) of the cost of performing the actual analysis. However, its accuracy in predicting the CPU and I/O resources depends intrinsically on the accuracy of calibration data that must be developed once for the computer hardware and the finite element analysis code of interest. Testing of the SCOPE code on the AMDAHL 470 V/8 computer and the ELAS finite element analysis program indicated small I/O errors (3.2 percent), larger CPU errors (17.8 percent), and negligible total errors (1.5 percent).

Melosh, R.↗
NASA NTRS1985

SSME lifetime prediction and verification, integrating environments, structures, materials: The challenge

The planned missions for the space shuttle dictated a unique and technology-extending rocket engine. The high specific impulse requirements in conjunction with a 55-mission lifetime, plus volume and weight constraints, produced unique structural design, manufacturing, and verification requirements. Operations from Earth to orbit produce severe dynamic environments, which couple with the extreme pressure and thermal environments associated with the high performance, creating large low cycle loads and high alternating stresses above endurance limit which result in high sensitivity to alternating stresses. Combining all of these effects resulted in the requirements for exotic materials, which are more susceptible to manufacturing problems, and the use of an all-welded structure. The challenge of integrating environments, dynamics, structures, and materials into a verified SSME structure is discussed. The verification program and developmental flight results are included. The first six shuttle flights had engine performance as predicted with no failures. The engine system has met the basic design challenges.

Ryan, R. S.↗
NASA NTRS1994

High Performance Parallel Analysis of Coupled Problems for Aircraft Propulsion

In order to predict the dynamic response of a flexible structure in a fluid flow, the equations of motion of the structure and the fluid must be solved simultaneously. In this paper, we present several partitioned procedures for time-integrating this focus coupled problem and discuss their merits in terms of accuracy, stability, heterogeneous computing, I/O transfers, subcycling, and parallel processing. All theoretical results are derived for a one-dimensional piston model problem with a compressible flow, because the complete three-dimensional aeroelastic problem is difficult to analyze mathematically. However, the insight gained from the analysis of the coupled piston problem and the conclusions drawn from its numerical investigation are confirmed with the numerical simulation of the two-dimensional transient aeroelastic response of a flexible panel in a transonic nonlinear Euler flow regime.

Felippa, C. A.↗
NASA NTRS1991

Development of structural composite mirror technology for submillimeter space telescopes

The technical approach to the design, manufacturing, testing, and analytical simulation of lightweight graphite/epoxy mirrors is described. The precision segmented reflector (PSR) program has produced (1) 1.0-m graphite/epoxy panels with areal densities of 7 kg/sq m as-manufactured surface precision near 1 micron rms, (2) 0.5-m panels with figure changes less than 1 micron rms for temperature reductions of 100 K, (3) analytical performance-prediction capability with submicron accuracy relative to panel thermal distortion, and (4) a unique thermal vacuum test facility for structural composite mirrors.

Freeland, R. E.↗
NASA NTRS2004

Automating Structural Analysis of Spacecraft Vehicles

A major effort within NASA's vehicle analysis discipline has been to automate structural analysis and sizing optimization during conceptual design studies of advanced spacecraft. Traditional spacecraft structural sizing has involved detailed finite element analysis (FEA) requiring large degree-of-freedom (DOF) finite element models (FEM). Creation and analysis of these models can be time consuming and limit model size during conceptual designs. The goal is to find an optimal design that meets the mission requirements but produces the lightest structure. A structural sizing tool called HyperSizer has been successfully used in the conceptual design phase of a reusable launch vehicle and planetary exploration spacecraft. The program couples with FEA to enable system level performance assessments and weight predictions including design optimization of material selections and sizing of spacecraft members. The software's analysis capabilities are based on established aerospace structural methods for strength, stability and stiffness that produce adequately sized members and reliable structural weight estimates. The software also helps to identify potential structural deficiencies early in the conceptual design so changes can be made without wasted time. HyperSizer's automated analysis and sizing optimization increases productivity and brings standardization to a systems study. These benefits will be illustrated in examining two different types of conceptual spacecraft designed using the software. A hypersonic air breathing, single stage to orbit (SSTO), reusable launch vehicle (RLV) will be highlighted as well as an aeroshell for a planetary exploration vehicle used for aerocapture at Mars. By showing the two different types of vehicles, the software's flexibility will be demonstrated with an emphasis on reducing aeroshell structural weight. Member sizes, concepts and material selections will be discussed as well as analysis methods used in optimizing the structure. Analysis based on the HyperSizer structural sizing software will be discussed. Design trades required to optimize structural weight will be presented.

Hrinda, Glenn A.↗
NASA NTRS1996

Novel Composites for Wing and Fuselage Applications: Novel Wing Design Concepts - Task 1

Design trade studies were conducted to arrive at advanced wing designs that integrated new material forms with innovative structural concepts and cost-effective fabrication methods. A representative spar was selected for design, fabrication, and test to validate the predicted performance. Textile processes, such as knitting, weaving and stitching, were used to produce fiber preforms that were later fabricated into composite span through epoxy Resin Transfer Molding (RTM), Resin Film Infusion (RFI), and consolidation of commingled thermoplastic and graphite tows. The target design ultimate strain level for these innovative structural design concepts was 6000 mu in. per in. The spars were subjected to four-point beam bending to validate their structural performance. The various material form /processing combination Y-spars were rated for their structural efficiency and acquisition cost. The acquisition cost elements were material, tooling, and labor.

Suarez, J. A.↗
NASA NTRS1986

Modeling of transient heat pipe operation

Mathematical models and associated solution procedures which can be used to design heat pipe cooled structures for use on hypersonic vehicles are being developed. The models should also have the capability to predict off-design performance for a variety of operating conditions. It is expected that the resulting models can be used to predict startup behavior of liquid metal heat pipes to be used in reentry vehicles, hypersonic aircraft, and space nuclear reactors. Work to date related to numerical solutions of governing differential equations for the outer shell and the combination capillary structure and working fluid is summarized. Finite element numerical equations using both implicit, explicit, and combination methods were examined.

Colwell, G. T.↗
NASA NTRS1989

Cosmological velocity correlations - Observations and model predictions

By applying the present simple statistics for two-point cosmological peculiar velocity-correlation measurements to the actual data sets of the Local Supercluster spiral galaxy of Aaronson et al. (1982) and the elliptical galaxy sample of Burstein et al. (1987), as well as to the velocity field predicted by the distribution of IRAS galaxies, a coherence length of 1100-1600 km/sec is obtained. Coherence length is defined as that separation at which the correlations drop to half their zero-lag value. These results are compared with predictions from two models of large-scale structure formation: that of cold dark matter and that of baryon isocurvature proposed by Peebles (1980). N-body simulations of these models are performed to check the linear theory predictions and measure sampling fluctuations.

Gorski, Krzysztof M.↗
NASA NTRS1980

Review - Axial compressor stall phenomena

Stall in compressors can be associated with the initiation of several types of fluid dynamic instabilities. These instabilities and the different phenomena, surge and rotating stall, which result from them, are discussed in this paper. Assessment is made of the various methods of predicting the onset of compressor and/or compression system instability, such as empirical correlations, linearized stability analyses, and numerical unsteady flow calculation procedures. Factors which affect the compressor stall point, in particular inlet flow distortion, are reviewed, and the techniques which are used to predict the loss in stall margin due to these factors are described. The influence of rotor casing treatment (grooves) on increasing compressor flow range is examined. Compressor and compression system behavior subsequent to the onset of stall is surveyed, with particular reference to the problem of engine recovery from a stalled condition. The distinction between surge and rotating stall is emphasized because of the very different consequences on recoverability. The structure of the compressor flow field during rotating stall is examined, and the prediction of compressor performance in rotating stall, including stall/unstall hysteresis, is described.

Greitzer, E. M.↗
NASA NTRS1985

Nonlinear Dynamic Analysis of Deploying Flexible Space Booms

A fundamental investigation of the planar deployment and lock-up of two flexible boom type appendages which have attached tip masses and are connected to a central rigid body through a rotational spring is presented. Nondimensional parameters are identified and it is shown that, in general, the solution depends only on two mass ratios and one nondimensional stiffness parameter. Results are presented for boom tip deflections, deployment time and root moments at lock-up. A threshold value of the nondimensional stiffness parameter is identified beyond which boom deflections become large. Also, a thorough examination of the effect of nonlinear terms in the equations governing the deployment phase is performed. Nonlinear terms in the deployment equations due to kinematics and structural deformation are required to predict more accurately boom deflections, but retention of an inconsistent set of nonlinear terms leads to erroneous results. In particular, retaining nonlinear kinematic terms while neglecting nonlinear structural terms can produce inaccurate results even below the threshold stiffness value.

Mcgowan, P. E.↗
NASA NTRS1991

Active vibration absorber for CSI evolutionary model: Design and experimental results

The development of control of large flexible structures technology must include practical demonstration to aid in the understanding and characterization of controlled structures in space. To support this effort, a testbed facility was developed to study practical implementation of new control technologies under realistic conditions. The design is discussed of a second order, acceleration feedback controller which acts as an active vibration absorber. This controller provides guaranteed stability margins for collocated sensor/actuator pairs in the absence of sensor/actuator dynamics and computational time delay. The primary performance objective considered is damping augmentation of the first nine structural modes. Comparison of experimental and predicted closed loop damping is presented, including test and simulation time histories for open and closed loop cases. Although the simulation and test results are not in full agreement, robustness of this design under model uncertainty is demonstrated. The basic advantage of this second order controller design is that the stability of the controller is model independent.

Bruner, Anne M.↗
NASA NTRS2010

A New Analysis Tool Assessment for Rotordynamic Modeling of Gas Foil Bearings

Gas foil bearings offer several advantages over traditional bearing types that make them attractive for use in high-speed turbomachinery. They can operate at very high temperatures, require no lubrication supply (oil pumps, seals, etc.), exhibit very long life with no maintenance, and once operating airborne, have very low power loss. The use of gas foil bearings in high-speed turbomachinery has been accelerating in recent years, although the pace has been slow. One of the contributing factors to the slow growth has been a lack of analysis tools, benchmarked to measurements, to predict gas foil bearing behavior in rotating machinery. To address this shortcoming, NASA Glenn Research Center (GRC) has supported the development of analytical tools to predict gas foil bearing performance. One of the codes has the capability to predict rotordynamic coefficients, power loss, film thickness, structural deformation, and more. The current paper presents an assessment of the predictive capability of the code, named XLGFBTH (Texas A&M University). A test rig at GRC is used as a simulated case study to compare rotordynamic analysis using output from the code to actual rotor response as measured in the test rig. The test rig rotor is supported on two gas foil journal bearings manufactured at GRC, with all pertinent geometry disclosed. The resulting comparison shows that the rotordynamic coefficients calculated using XLGFBTH represent the dynamics of the system reasonably well, especially as they pertain to predicting critical speeds.

Howard, Samuel A.↗
NASA NTRS1990

On the nature of the interaction between structures and actuators in vibration suppression

This lecture presents a summary of work on the analysis of the interaction between a structure, an actuator used to suppress the vibration of the structure, and the control law implemented by the actuator. Two control applications are considered. First, a proof-mass actuator with experimentally verified dynamics, capable of being used in a space structure configuration is examined. This is connected to a cantilevered beam modeled as a single degree of freedom system. Secondly, an electric motor, again with experimentally verified dynamics, is used to slew a beam modeled by a partial differential equation. Both the experimental and numerical configuration predict the presence of potential instabilities in system performance if proper consideration is not given to interactions between the control law, the structure and the actuator. In addition, an understanding of the interaction is shown to greatly effect performance. In particular it is shown that judicious choice of actuator parameters greatly improves closed loop performance.

Inman, Daniel J.↗
NASA NTRS2024

Modeling Dynamic Crush Behavior of Carbon Fiber Reinforced Polymer Composite Structures Using MAT213

Modeling crushing of carbon fiber reinforced polymer (CFRP) composites is challenging, and current simulation methodologies involve tuning of non-physical parameters. MAT213, a next-generation material model, has advanced functionality to better simulate dynamic impact loading. The objective of the present investigation is to evaluate the potential for using MAT213 to simulate dynamic crushing of CFRPs. Two sets of simulations were performed: one for calibration based on a set of coupon-level experiments and another for prediction of the response of structural elements. Simulations involving dynamic crushing of flat specimens were iteratively run to calibrate model parameters. The calibration demonstrated that MAT213 could produce a simulated force-displacement response within experimental scatter. The simulated failure morphology was also comparable to the experiments. After successful calibration, predictive simulations of dynamic crushing of C-channel shaped specimens were completed using a simulated crash sled test rig and two pairs of impactor mass/velocity conditions. The simulated force-displacement curve in the crash sled simulations for the lower-velocity condition fell within the experimental scatter, but the stable crush force was underpredicted by 27% in the higher-velocity simulations. Better correlation in the lower-velocity test condition likely results from the calibration condition being a similar velocity to the lower-velocity crash sled condition.

Dynamic Crush↗
NASA NTRS2004

New Tool Released for Engine-Airframe Blade-Out Structural Simulations

Researchers at the NASA Glenn Research Center have enhanced a general-purpose finite element code, NASTRAN, for engine-airframe structural simulations during steady-state and transient operating conditions. For steady-state simulations, the code can predict critical operating speeds, natural modes of vibration, and forced response (e.g., cabin noise and component fatigue). The code can be used to perform static analysis to predict engine-airframe response and component stresses due to maneuver loads. For transient response, the simulation code can be used to predict response due to bladeoff events and subsequent engine shutdown and windmilling conditions. In addition, the code can be used as a pretest analysis tool to predict the results of the bladeout test required for FAA certification of new and derivative aircraft engines. Before the present analysis code was developed, all the major aircraft engine and airframe manufacturers in the United States and overseas were performing similar types of analyses to ensure the structural integrity of engine-airframe systems. Although there were many similarities among the analysis procedures, each manufacturer was developing and maintaining its own structural analysis capabilities independently. This situation led to high software development and maintenance costs, complications with manufacturers exchanging models and results, and limitations in predicting the structural response to the desired degree of accuracy. An industry-NASA team was formed to overcome these problems by developing a common analysis tool that would satisfy all the structural analysis needs of the industry and that would be available and supported by a commercial software vendor so that the team members would be relieved of maintenance and development responsibilities. Input from all the team members was used to ensure that everyone's requirements were satisfied and that the best technology was incorporated into the code. Furthermore, because the code would be distributed by a commercial software vendor, it would be more readily available to engine and airframe manufacturers, as well as to nonaircraft companies that did not previously have access to this capability.

Lawrence, Charles↗
NASA NTRS1994

Structure of supersonic jet flow and its radiated sound

The present paper explores the use of large-eddy simulations as a tool for predicting noise from first principles. A high-order numerical scheme is used to perform large-eddy simulations of a supersonic jet flow with emphasis on capturing the time-dependent flow structure representating the sound source. The wavelike nature of this structure under random inflow disturbances is demonstrated. This wavelike structure is then enhanced by taking the inflow disturbances to be purely harmonic. Application of Lighthill's theory to calculate the far-field noise, with the sound source obtained from the calculated time-dependent near field, is demonstrated. Alternative approaches to coupling the near-field sound source to the far-field sound are discussed.

Mankbadi, Reda R.↗