Search NASA⌕ Search

SEARCH · Search NASA

Results for “Surface effect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Surface scattering effects at different spectral regions

The development of theoretical models of rough surface scattering in different frequency regions is reviewed. The applications of the models to four different types of rough surface scattering are presented. The four categories of surface roughness effects are: (1) where the angular distribution of first-order average incoherent scattered power is proportional to the roughness spectrum of the surface; (2) where the horizontal roughness scale is less than the incident wavelength; (3) where both the horizontal and vertical roughness scales are large compared to the incident wavelength; and (4) scattering in the specular direction is dominated by large-scale roughness, and scattering in the opposite direction is dominated by small-scale roughness. Acoustic, optical and microwave scattering measurements from rough surfaces are presented which illustrate the four types of scattering behavior.

Fung, A. K.↗

Comparison of steady and transient flow boiling critical heat flux for FeCrAl accident tolerant fuel cladding alloy, Zircaloy, and Inconel

Steady and transient (with a heating rate of 685?/s) internal-flow CHF (Critical Heat Flux) experiments were conducted under atmospheric pressure at a fixed inlet temperature (40? or 60?) and mass flow (300kg/m 2 s) on Fe-13Cr-6Al alloy, Inconel 600 and Zircaloy-4 tube samples. Multiple experiments were repeated on the same specimen to investigate the effect of surface characteristic changes (i.e., roughness, wettability, and oxide scale morphology) on the occurrence of CHF. Despite notable changes of wettability, roughness, and oxide layer characteristics on samples that had already been subjected to CHF, measured flow CHF remained unchanged throughout repeated experiments for tested materials. This demonstrates that the surface effects on flow CHF are limited in the test conditions. In the steady-state flow boiling condition, Fe-13Cr-6Al alloy demonstrated a 22% and 14% increase in CHF compared to Zircaloy-4 and Inconel 600, respectively. Compared to the 2006 Groeneveld CHF lookup table, Fe-13Cr-6Al alloy gives a 13% increase in the tested flow boiling condition. Material properties are considered primarily responsible for the observed CHF differences among the tested materials. The surface thermal economy parameter $\frac{(pc_p)^{3/2}}{\sqrt{k}}$ is proposed as an explanation for the observed CHF differences; this parameter is related to material’s ability to avoid an irreversible dry spot formation. The apparent disagreement of Zircaloy-4 CHF with both the look up table predictions and Inconel 600 shows the limitation of departure of nuclate boiling (DNB) evaluations that do not consider cladding materials. The transient Fe-13Cr-6Al CHF is 39% and 23% higher than the lookup table prediction and the steady-state condition experimental result, respectively.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effect of surface potential and charge transfer mechanism in reduced graphene oxide and magnetic nanocomposites

Highlights: • Cobalt oxide/reduced graphene oxide nanocomposites were prepared by hydrothermal method. • The of cobalt oxide nanoparticles on graphene oxide sheets leads modification of surface potential of graphene oxide sheets. • Modification of surface potential causes shifting of Fermi energy level of graphene oxide sheets due to charge transfer process. • The occurrence function of graphene oxide sheets modified from 4.5 eV to 5.8 eV by decoration of cobalt oxide nanoparticles on it. • The work of charge transfer between cobalt oxide nanoparticles and graphene oxide sheets also envisaged from Raman spectra. - Abstract: In this paper, the charge transfer mechanism in hydrothermally synthesized cobalt oxide/reduced graphene oxide (Co{sub 3}O{sub 4}/RGO) nanocomposites has been established. Scanning and transmission electron microscopy results expose the decoration of Co{sub 3}O{sub 4} nanoparticles on GO sheets. Magnetic response of nanocomposites was confirmed from superconducting quantum interference device magnetometer measurement. Raman spectroscopy investigated optical properties of these nanocomposites. The Raman spectra of Co{sub 3}O{sub 4}/RGO nanocomposites shows the enhancement of D and G bands which are associated with GO due to the Surface-enhanced Raman spectroscopy effect and blue shift. Increase in the full-width half-maximum value as well as upshift in D and G peaks are strong signals of association of charge transfer process between GO sheets and decorated Co{sub 3}O{sub 4} nanoparticles. The effect of charge transfer process is measured in the expression of shifting of Fermi energy level of Co{sub 3}O{sub 4}/RGO nanocomposites. Charge transfer is correlated with observed Raman shift and scanning Kelvin probe microscopy. XRD spectra of Co{sub 3}O{sub 4}/RGO confirm the polycrystalline nature of Co{sub 3}O{sub 4} nanoparticles.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Impurity Extraction by Droplets

The goals are to model and to measure the phase equilibrium properties of a finely divided fluid containing a large number of chemically similar species. The objective is to develop an accurate, usable model for such phenomena as pollutant extraction of rain clouds, industrial separation in spray towers, and separation in emulsions. The project was designed as a hierarchy of complementary theoretical and experimental steps. A theory was developed to describe the segregation of complex impurities at the interface of a solvent. This phenomenon is important in phase behavior when a large fraction of molecules in a material are near an interface, the situation in a finely divided material. The theory will be modified to account for the effect of surface curvature on the surface tension. The study of mixtures differs from pure fluids not only because of the surface effects but also because composition differences between the droplet and the surrounding vapor can stabilize a droplet with respect to a bulk phase.

Morrison, G.↗

Fundamental Investigations into the Properties and Performance of Advanced Materials

Intelligent engineering designs require an accurate understanding of material behavior, since any uncertainties or gaps in knowledge must be counterbalanced with heightened factors of safety, leading to overdesign. Therefore, building better structures and pushing the performance of new components requires an improved understanding of the thermomechanical response of advanced materials under service conditions. This dissertation provides fundamental investigations of several advanced materials: thermoset polymers, a common matrix material for fiber-reinforced composites and nanocomposites; aluminum alloy 7075-T6 (AA7075-T6), a high-performance aerospace material; and ceramic matrix composites (CMCs), an advanced composite for extreme-temperature applications. To understand matrix interactions with various interfaces and nanoinclusions at their fundamental scale, the properties of thermoset polymers are studied at the atomistic scale. An improved proximity-based molecular dynamics (MD) technique for modeling the crosslinking of thermoset polymers is carefully established, enabling realistic curing simulations through its ability to dynamically and probabilistically perform complex topology transformations. The proximity-based MD curing methodology is then used to explore damage initiation and the local anisotropic evolution of mechanical properties in thermoset polymers under uniaxial tension with an emphasis on changes in stiffness through a series of tensile loading, unloading, and reloading experiments. Aluminum alloys in aerospace applications often require a fatigue life of over 109 cycles, which is well over ii the number of cycles that can be practically tested using conventional fatigue testing equipment. In order to study these high-life regimes, a detailed ultrasonic cycle fatigue study is presented for AA7075-T6 under fully reversed tension-compression loading. The geometric sensitivity, frequency effects, size effects, surface roughness effects, and the corresponding failure mechanisms for ultrasonic fatigue across different fatigue regimes are investigated. Finally, because CMCs are utilized in extreme environments, oxidation plays an important role in their degradation. A multiphysics modeling methodology is thus developed to address the complex coupling between oxidation, mechanical stress, and oxygen diffusion in heterogeneous carbon fiber-reinforced CMC microstructures.

Schichtel, Jacob J.↗

Effect of surface fields on the dynamic resistance of planar HgCdTe mid-wavelength infrared photodiodes

This work investigates the effect of surface fields on the dynamic resistance of a planar HgCdTe mid-wavelength infrared photodiode from both theoretical and experimental aspects, considering a gated n-on-p diode with the surface potential of its p-region modulated. Theoretical models of the surface leakage current are developed, where the surface tunnelling current in the case of accumulation is expressed by modifying the formulation of bulk tunnelling currents, and the surface channel current for strong inversion is simulated with a transmission line method. Experimental data from the fabricated devices show a flat-band voltage of V{sub FB}=−5.7 V by capacitance-voltage measurement, and then the physical parameters for bulk properties are determined from the resistance-voltage characteristics of the diode working at a flat-band gate voltage. With proper values of the modeling parameters such as surface trap density and channel electron mobility, the theoretical R{sub 0}A product and corresponding dark current calculated from the proposed model as functions of the gate voltage V{sub g} demonstrate good consistency with the measured values. The R{sub 0}A product remarkably degenerates when V{sub g} is far below or above V{sub FB} because of the surface tunnelling current or channel current, respectively; and it attains the maximum value of 5.7×10{sup 7} Ω · cm{sup 2} around the transition between surface depletion and weak inversion when V{sub g}≈−4 V, which might result from reduced generation-recombination current.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Multidimensional Modeling of Atmospheric Effects and Surface Heterogeneities on Remote Sensing

A modeling capability that allows a quantitative determination of atmospheric effects on remote sensing including the effects of surface heterogeneities is established. The objectives include: (1) the adaptation of existing radiative transfer codes to remote sensing applications, (2) the implementation of a realistic atmospheric data base, (3) the definition and verification against field measurements of a coupled atmosphere/canopy model, and (4) the quantitative characterization of the effects of some biophysical canopy parameters and soil surface boundary conditions on satellite-sensed Multispectral Scanner System (MSS) data. Substantial progress was also made in quantifying the effects of varying atmospheric turbidity and different non-Lambertian and specular ground reflectances on MSS data and its transforms like greenness and brightness.

Gerstl, S. A.↗

Effect of Surface Treatment on High-Temperature Oxidation Behavior of IN 713C

The effects of surface preparations on oxidation kinetics and oxide scale morphology for the commercially available Ni-based superalloy IN 713C have been investigated. The ground and polished samples were exposed in air at 800-1100 °C. The ground specimens were found to demonstrate lower oxidation kinetics compared to those after polishing. The grinding also affected the oxide scale morphology, resulting in a protective alumina scale, while the polished samples developed Ni-/Cr-rich mixed oxides on the surface. Better oxidation resistance of the ground surfaces is related to a higher concentration of defects in the near-surface region introduced by cold working. These defects facilitate the outward transport of the scale-forming element Al and thus are beneficial for protective oxidation. The oxidation mechanism at lower temperatures was introduced. The model based on the generalized Darken method and multiphase approximation was proposed.

36 MATERIALS SCIENCE↗

Modeling surface motion effects in N{sub 2} dissociation on W(110): Ab initio molecular dynamics calculations and generalized Langevin oscillator model

Accurately modeling surface temperature and surface motion effects is necessary to study molecule-surface reactions in which the energy dissipation to surface phonons can largely affect the observables of interest. We present here a critical comparison of two methods that allow to model such effects, namely, the ab initio molecular dynamics (AIMD) method and the generalized Langevin oscillator (GLO) model, using the dissociation of N{sub 2} on W(110) as a benchmark. AIMD is highly accurate as the surface atoms are explicitly part of the dynamics, but this advantage comes with a large computational cost. The GLO model is much more computationally convenient, but accounts for lattice motion effects in a very approximate way. Results show that, despite its simplicity, the GLO model is able to capture the physics of the system to a large extent, returning dissociation probabilities which are in better agreement with AIMD than static-surface results. Furthermore, the GLO model and the AIMD method predict very similar energy transfer to the lattice degrees of freedom in the non-reactive events, and similar dissociation dynamics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Disentangling fluxes of energy and matter in plasma-surface interactions: Effect of process parameters

The possibility to discriminate between the relative importance of the fluxes of energy and matter in plasma-surface interaction is demonstrated by the energy flux measurements in low-temperature plasmas ignited by the radio frequency discharge (power and pressure ranges 50-250 W and 8-11.5 Pa) in Ar, Ar+H{sub 2}, and Ar+H{sub 2}+CH{sub 4} gas mixtures typically used in nanoscale synthesis and processing of silicon- and carbon-based nanostructures. It is shown that by varying the gas composition and pressure, the discharge power, and the surface bias one can effectively control the surface temperature and the matter supply rates. The experimental findings are explained in terms of the plasma-specific reactions in the plasma bulk and on the surface.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗