SEARCH · Search NASA

Results for “THRUST AUGMENTATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

All sources NASA NTRS DOE OSTI

NASA NTRS1987

Airflow calibration and exhaust pressure/temperature survey of an F404, S/N 215-109, turbofan engine

A General Electric F-404 turbofan engine was calibrated for thrust and airflow at the NASA Lewis Propulsion System Laboratory in support of future flight tests of the X-29 aircraft. Tests were conducted with and without augmentation, over a range of flight conditions, including the two design points of the airplane. Data obtained during the altitude tests will be used to correct two independent gross thrust calculation routines which will be installed and operated on the airplane to determine in-flight gross thrust. Corrected airflow data as a function of corrected fan speed collapsed onto a single curve. Similarly, trends were observed and defined for both augmented and dry thrust. Overall agreement between measured data and F-404 Engine Spec Deck data was within 2 percent for airflow and 6 percent for thrust. The results of an uncertainty analysis for thrust and airflow is presented. In addition to the thrust calibration, the exhaust gas boundary layer pressure and temperatures were surveyed at selected condition and engine power levels to obtain data for another NASA F-404 program. Test data for these surveys are presented.

Burns, Maureen E.↗

NASA NTRS1992

Flight evaluation of an extended engine life mode on an F-15 airplane

An integrated flight and propulsion control system designed to reduce the rate of engine deterioration was developed and evaluated in flight on the NASA Dryden F-15 research aircraft. The extended engine life mode increases engine pressure ratio while reducing engine airflow to lower the turbine temperature at constant thrust. The engine pressure ratio uptrim is modulated in real time based on airplane maneuver requirements, flight conditions, and engine information. The extended engine life mode logic performed well, significantly reducing turbine operating temperature. Reductions in fan turbine inlet temperature of up to 80 F were obtained at intermediate power and up to 170 F at maximum augmented power with no appreciable loss in thrust. A secondary benefit was the considerable reduction in thrust-specific fuel consumption. The success of the extended engine life mode is one example of the advantages gained from integrating aircraft flight and propulsion control systems.

Myers, Lawrence P.↗

NASA NTRS1993

ASRM Multi-Port Igniter Flow Field Analysis

The Advanced Solid Rocket Motor (ASRM) program was initiated by NASA in response to the need for a new generation rocket motor capable of providing increased thrust levels over the existing Redesigned Solid Rocket Motor (RSRM) and thus augment the lifting capacity of the space shuttle orbiter. To achieve these higher thrust levels and improve motor reliability, advanced motor design concepts were employed. In the head end of the motor, for instance, the propellent cast has been changed from the conventional annular configuration to a 'multi-slot' configuration in order to increase the burn surface area and guarantee rapid motor ignition. In addition, the igniter itself has been redesigned and currently features 12 exhaust ports in order to channel hot igniter combustion gases into the circumferential propellent slots. Due to the close proximity of the igniter ports to the propellent surfaces, new concerns over possible propellent deformation and erosive burning have arisen. The following documents the effort undertaken using computational fluid dynamics to perform a flow field analysis in the top end of the ASRM motor to determine flow field properties necessary to permit a subsequent propellent fin deformation analysis due to pressure loading and an assessment of the extent of erosive burning.

Kania, Lee↗

NASA NTRS1983

A parametric study of thermally augmented O2/H2 rocket enines

An analysis is presented of the performance of a conceptual propulsion system in which liquid hydrogen and liquid oxygen are first vaporized and heated by thermal power from a spacecraft nuclear electric power supply prior to combustion in a rocket engine. Calculations of the specific impulse (I-sp) are presented for a series of O2/H2 oxidizer-to-fuel mixture ratios and reactant pre-heat temperatures (T-aug). It is found that the ratio of the augmentation power to the total engine jet power (P-aug/P-tot) determines the engine thrust for a given P-aug, T-aug, and I-sp. In addition, the performance of an unaugmented O2/H2 and a heated-hydrogen rocket engine were also calculated for the same conditions. Results show that an augmented O2/H2 engine has three to eight times the thrust of a heated H2 engine for a given P-aug. It is concluded that it should be possible to design a high/low thrust propulsion system using a common propellant, with the option of using thermal power from the nuclear electric power supply to augment the low-thrust propulsion system during cruise periods when the reactor's full electric power is not needed.

Frisbee, R. H.↗

NASA NTRS1988

Turbofan forced mixer lobe flow modeling. Part 3: Application to augment engines

Military engines frequently need large quantities of thrust for short periods of time. The addition of an augmentor can provide such thrust increases but with a penalty of increased duct length and engine weight. The addition of a forced mixer to the augmentor improves performance and reduces the penalty, as well as providing a method for siting the required flame holders. In this report two augmentor concepts are investigated: a swirl-mixer augmentor and a mixer-flameholder augmentor. Several designs for each concept are included and an experimental assessment of one of the swirl-mixer augmentors is presented.

Barber, T.↗

NASA NTRS2011

Engine Yaw Augmentation for Hybrid-Wing-Body Aircraft via Optimal Control Allocation Techniques

Asymmetric engine thrust was implemented in a hybrid-wing-body non-linear simulation to reduce the amount of aerodynamic surface deflection required for yaw stability and control. Hybrid-wing-body aircraft are especially susceptible to yaw surface deflection due to their decreased bare airframe yaw stability resulting from the lack of a large vertical tail aft of the center of gravity. Reduced surface deflection, especially for trim during cruise flight, could reduce the fuel consumption of future aircraft. Designed as an add-on, optimal control allocation techniques were used to create a control law that tracks total thrust and yaw moment commands with an emphasis on not degrading the baseline system. Implementation of engine yaw augmentation is shown and feasibility is demonstrated in simulation with a potential drag reduction of 2 to 4 percent. Future flight tests are planned to demonstrate feasibility in a flight environment.

Taylor, Brian R.↗

NASA NTRS2011

Engine Yaw Augmentation for Hybrid-Wing-Body Aircraft via Optimal Control Allocation Techniques

Taylor, Brian R.↗

NASA NTRS1984

Energy Efficient Engine exhaust mixer model technology report addendum; phase 3 test program

The Phase 3 exhaust mixer test program was conducted to explore the trends established during previous Phases 1 and 2. Combinations of mixer design parameters were tested. Phase 3 testing showed that the best performance achievable within tailpipe length and diameter constraints is 2.55 percent better than an optimized separate flow base line. A reduced penetration design achieved about the same overall performance level at a substantially lower level of excess pressure loss but with a small reduction in mixing. To improve reliability of the data, the hot and cold flow thrust coefficient analysis used in Phases 1 and 2 was augmented by calculating percent mixing from traverse data. Relative change in percent mixing between configurations was determined from thrust and flow coefficient increments. The calculation procedure developed was found to be a useful tool in assessing mixer performance. Detailed flow field data were obtained to facilitate calibration of computer codes.

Larkin, M. J.↗

NASA NTRS2010

A Coupled Aeroelastic Model for Launch Vehicle Stability Analysis

A technique for incorporating distributed aerodynamic normal forces and aeroelastic coupling effects into a stability analysis model of a launch vehicle is presented. The formulation augments the linear state-space launch vehicle plant dynamics that are compactly derived as a system of coupled linear differential equations representing small angular and translational perturbations of the rigid body, nozzle, and sloshing propellant coupled with normal vibration of a set of orthogonal modes. The interaction of generalized forces due to aeroelastic coupling and thrust can be expressed as a set of augmenting non-diagonal stiffness and damping matrices in modal coordinates with no penalty on system order. While the eigenvalues of the structural response in the presence of thrust and aeroelastic forcing can be predicted at a given flight condition independent of the remaining degrees of freedom, the coupled model provides confidence in closed-loop stability in the presence of rigid-body, slosh, and actuator dynamics. Simulation results are presented that characterize the coupled dynamic response of the Ares I launch vehicle and the impact of aeroelasticity on control system stability margins.

Orr, Jeb S.↗

NASA NTRS1985

Performance characterization tests of a 1-kW resistojet using hydrogen, nitrogen and ammonia as propellants

A performance mapping test of a 1 kW radiatively heated resistojet demonstrated high specific impulse and efficiency with hydrogen, nitrogen and ammonia as propellants. The resistojet was based on an unmodified augmentation section of the flight-qualified Rocket Research Company Augmented Catalytic Thruster. Peak specific impulse values of 686.9 sec for hydrogen, 191.6 sec for nitrogen, and 342 sec for ammonia were demonstrated. A maximum specific impulse efficiency of 94.3 percent was demonstrated with hydrogen. Testing covered a thrust range of 27 to 112 mlbf with augmentation powers ranging from 300 to 1000 watts. A total of 83 runs accumulating 25 hours of operation were conducted with the three propellants. Comparison of specific impulse efficiency to other published resistojet performance data showed the radiatively heated resistojet compares favorably to other design concepts.

Miyake, C. I.↗

NASA NTRS1995

Propulsion Controlled Aircraft design and development

This paper describes the design, development, and ground testing of the propulsion controlled aircraft (PCA) flight control system. A backup flight control system which uses only engine thrust, the PCA system utilizes collective and differential thrust changes to steer an aircraft that experiences partial or complete failure of the hydraulically actuated control surfaces. The objective of the program was to investigate, in flight, the throttles-only control capability of the F-15, using manual control, and also an augmented PCA mode in which computer-controlled thrust was used for flight control. The objective included PCA operation in up-and-away flight and, if performance was adequate, a secondary objective to make actual PCA landings. The PCA design began with a feasibility study which evaluated many control law designs. The study was done using off-line control analysis, simulation, and on-line manned flight simulator tests. Control laws, cockpit displays, and cockpit controls were evaluated by NASA test pilots. A flight test baseline configuration was selected based on projected flight performance, applicability to transport and fighter aircraft, and funding costs. During the PCA software and hardware development, the initial design was updated as data became available from throttle-only flight experiments conducted by NASA on the F-15. This information showed basic airframe characteristics that were not observed in the F-15 flight simulator and resulted in several design changes. After the primary objectives of the PCA flight testing were accomplished, additional PCA modes of operation were developed and implemented. The evolution of the PCA system from the initial feasibility study, control law design, simulation, hardware-in-the-loop tests, pilot-in-the-loop tests, and ground tests is presented.

Wells, Edward A.↗

NASA NTRS1989

Aerodynamics of thrust vectoring

Thrust vectoring as a means to enhance maneuverability and aerodynamic performane of a tactical aircraft is discussed. This concept usually involves the installation of a multifunction nozzle. With the nozzle, the engine thrust can be changed in direction without changing the attitude of the aircraft. Change in the direction of thrust induces a significant change in the aerodynamic forces on the aircraft. Therefore, this device can be used for lift-augmenting as well as stability and control purposes. When the thrust is deflected in the longitudinal direction, the lift force and the pitching stability can be manipulated, while the yawing stability can be controlled by directing the thrust in the lateral direction.

Tseng, J. B.↗

NASA NTRSDate not supplied

A Study of Large Scale Power Extraction and Insertion on Turbofan Performance and Stability

This describes the effects of turbofan power extraction and insertion (augmentation) on engine performance and stability. The purpose of this paper is to present how power augmentation affects a dual spool gas turbine engine cycle where the engine will also be required to provide thrust. The goals for the paper are to describe effective limits of power augmentation and offer strategies, utilizing spool choice and variable geometries, to maximize augmentation effect. While Analysis is general, two potential uses are explored: Power extraction for electrified aircraft propulsion and power insertion for thrust assist. Results of the paper show it is possible to extract over 20% (at 85% max thrust) and gain roughly 12% of maximum thrust through power insertion.

Gas Turbine engines↗

NASA NTRS2021

A Study of Large-Scale Power Extraction and Insertion on Turbofan Performance and Stability

This paper describes the effects of turbofan power extraction and insertion (augmentation) on engine performance and stability. The purpose of this paper is to present how power augmentation affects a dual spool gas turbine engine cycle where the engine will also be required to provide thrust. The goals for the paper are to describe effective limits of power augmentation and offer strategies, utilizing spool choice and variable geometries, to maximize augmentation effect. While Analysis is general, two potential uses are explored: Power extraction for electrified aircraft propulsion and power insertion for thrust assist. Results of the paper show it is possible to extract over 20% (at 85% max thrust) and gain roughly 12% of maximum thrust through power insertion.

Gas Turbine engines↗

NASA NTRSDate not supplied

A Study of Large Scale Power Extraction and Insertion on Turbofan Performance and Stability

This paper describes the effects of turbofan power extraction and insertion (augmentation) on engine performance and stability. The purpose of this paper is to present how power augmentation affects a dual spool gas turbine engine cycle where the engine will also be required to provide thrust. The goals for the paper are to describe effective limits of power augmentation and offer strategies, utilizing spool choice and variable geometries, to maximize augmentation effect. While Analysis is general two potential uses are explored: Power extraction for electrified aircraft propulsion purposes. And, Power insertion for thrust assist. Results of the paper show it is possible to extract over 20% (at 85% max thrust) and gain roughly 12% of maximum thrust through power insertion.

Gas Turbine Engines↗

NASA NTRS1977

Performance tests with a 4.75 inch bore tapered-roller bearings at high speeds

The tapered-roller bearings were tested at speeds to 15,000 rpm which results in a cone-rib tangential velocity of 130 m/sec. (25,500 ft/min). Lubrication was applied either by jets or directly to the cone-rib, augmented with jets. Additional test parameters included thrust loads to 53,400 N (12,000 lbs), radial loads to 26,700 N (6,000 lbs), lubricant flow rates from 1.9 x 0.000 to 15.1 x 0.001 cubic meter/min. (0.5 to 4.0 gpm), and lubricant inlet temperatures of 350 K and 364 K (170 F and 195 F). Temperature distribution, separator speed, and drive-motor power demand were determined as functions of these test parameters.

Signer, H. R.↗

NASA NTRS1984

Circulation control technology applied to propulsive high lift systems

Technology developed for the Circulation Control Wing high-lift system has been extended to augment lift by entraining and redirecting engine thrust. Ejecting a thin jet sheet tangentially over a small curved deflecting surface adjacent to the slipstream of a turbofan engine causes the slipstream to flow around that deflecting surface. The angle of deflection is controlled pneumatically by varying the momentum of the thin jet sheet. The downward momentum of the slipstream enhances wing lift. This concept of pneumatically deflecting the slipstream has been applied to an upper surface blowing high-lift system and to a thrust deflecting system. The capability of the pneumatic upper surface blowing system was demonstrated in a series of investigations using a wind tunnel model and the NASA Quiet Short-haul Research Aircraft (QSRA). Full-scale thrust deflections greater than 90 deg were achieved. This mechanically simple system can provide increased maneuverability, heavy lift or overload capability, or short takeoff and landing performance.

Englar, R. J.↗

NASA NTRS2004

Fire Prevention, Detection and Suppression

In mid-1999, the Space and Life Sciences Directorate at Johnson Space Center was challenged to develop a new paradigm for NASA human life sciences: space medicine, space biomedical research and countermeasures, advanced human support technology. A new thrust - Bioastronautics - was formulated with a budget augmentation request. The objective are: expanded extramural community participation through the National Space Biomedical Research Institute, initiated the detailed planning and implementation of Bioastronautics, an integrated approach to ensure healthy and safe human space travel, assist in the solution of earth-based problems.

Ruff, Gary A.↗