SEARCH · Search NASA

Results for “TIP SPEED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Bending-torsion flutter of a highly swept advanced turboprop

Experimental and analytical results are presented for a bending-torsion flutter phenomena encountered during wind-tunnel testing of a ten-bladed, advanced, high-speed propeller (turboprop) model with thin airfoil sections, high blade sweep, low aspect ratio, high solidity and transonic tip speeds. Flutter occurred at free-stream Mach numbers of 0.6 and greater and when the relative tip Mach number (based on vector sum of axial and tangential velocities) reached a value of about one. The experiment also included two- and five-blade configurations. The data indicate that aerodynamic cascade effects have a strong destabilizing influence on the flutter boundary. The data was correlated with analytical results which include aerodynamic cascade effects and good agreement was found.

Mehmed, O.↗

NASA NTRS1975

Two-stage, low noise advanced technology fan. 4: Aerodynamic final report

A two-stage research fan was tested to provide technology for designing a turbofan engine for an advanced, long range commercial transport having a cruise Mach number of 0.85 -0.9 and a noise level 20 EPNdB below current requirements. The fan design tip speed was 365.8m/sec (1200ft/sec);the hub/tip ratio was 0.4; the design pressure ratio was 1.9; and the design specific flow was 209.2 kg/sec/sq m(42.85lbm/sec/sq ft). Two fan-versions were tested: a baseline configuration, and an acoustically treated configuration with a sonic inlet device. The baseline version was tested with uniform inlet flow and with tip-radial and hub-radial inlet flow distortions. The baseline fan with uniform inlet flow attained an efficiency of 86.4% at design speed, but the stall margin was low. Tip-radial distortion increased stall margin 4 percentage points at design speed and reduced peak efficiency one percentage point. Hub-radial distortion decreased stall margin 4 percentage points at all speeds and reduced peak efficiency at design speed 8 percentage points. At design speed, the sonic inlet in the cruise position reduced stall margin one percentage point and efficiency 1.5 to 4.5 percentage points. The sonic inlet in the approach position reduced stall margin 2 percentage points.

Harley, K. G.↗

NASA NTRS1980

Design and cold-air test of single-stage uncooled turbine with high work output

A solid version of a 50.8 cm single stage core turbine designed for high temperature was tested in cold air over a range of speed and pressure ratio. Design equivalent specific work was 76.84 J/g at an engine turbine tip speed of 579.1 m/sec. At design speed and pressure ratio, the total efficiency of the turbine was 88.6 percent, which is 0.6 point lower than the design value of 89.2 percent. The corresponding mass flow was 4.0 percent greater than design.

Moffitt, T. P.↗

NASA NTRS1973

High loading, low speed fan study, 5

A low speed, low noise, single stage fan was designed and tested. Design pressure ratio was 1.5 at a rotor tip speed of 1000 ft/sec. No inlet guide vane was used, the rotor stator was spaced and the number of rotor and stator airfoils was selected for low noise. Tests were conducted with uniform and distorted inlet flows. Stall margin of the initial design was too low for practical application. Airfoil slots and boundary layer and endwall devices did not improve stall margin sufficiently. A redesigned stator with reduced loadings increased stall margin, giving a fan efficiency of 0.883, 15% stall margin, and a 1.474 pressure radio at a specific flow of 41.7 lb/sec sq ft. Casing treatment over rotor tips improved stall margin with distorted inlet flow; vortex generators did not. Blade passing frequency noise increased with rotor relative Mach number. No supersonic fan noise was measured below 105% of design speed. Slotting airfoils, casing treatments, and a reduction of the ratio (number-stators/number-rotors) from (2n + 16) to (2n + 2) had no significant effects on noise.

Keenan, M. J.↗

NASA NTRS1935

Full-Scale Wind-Tunnel Tests of a PCA-2 Autogiro Rotor

This report presents the results of force tests on and air-flow surveys near PCA-2 autogiro rotor in the NACA full-scale wind tunnel. The force tests were made at three pitch settings and several rotor speeds; the effect of fairing protuberances on the rotor blade was determined. Induced downwash and yaw angles were determined at low tip-speed ratios in a plane 1 1/2 feet above the path of the blade tips. The results show that the maximum l/d of the rotor cannot be appreciably increased by increasing the blade pitch angle above about 4.5 degrees at the blade tip; that the protuberances on the blades cause more than 5 percent of the total rotor drag; and that the rotor center-of-pressure travel is very small.

Wheatley, John B↗

NASA NTRS1973

An experimental investigation of vortex stability, tip shapes, compressibility, and noise for hovering model rotors

Schlieren methods of flow visualization and hot-wire anemometry for velocity measurements were used to investigate the wakes generated by hovering model propellers and rotors. The research program was directed toward investigating (1) the stability of the tip vortex, (2) the effects produced by various tip shapes on performance and tip vortex characteristics, and (3) the shock formation and noise characteristics associated with various tip shapes. A free-wake analysis was also conducted for comparison with the vortex stability experimental results. Schlieren photographs showing wake asymmetry, interaction, and instability are presented along with a discussion of the effects produced by the number of blades, collective pitch, and tip speed. Two hot-wire anemometer techniques, used to measure the maximum circumferential velocity in the tip vortex, are discussed.

Tangler, J. L.↗

NASA NTRS1979

A flight investigation of performance and loads for a helicopter with NLR-1T main-rotor blade sections

Data on performance and rotor loads for a teetering-rotor, AH-1G helicopter flown with a main rotor that had the NLR-1T airfoil as the blade-section contour are presented. The test envelope included hover, forward-flight speed sweeps from 35 to 85 m/sec, and collective-fixed maneuvers at about 0.25 tip-speed ratio. The data set for each test point described vehicle flight state, control positions, rotor loads, power requirements, and blade motions. Rotor loads are reviewed primarily in terms of peak-to-peak and harmonic content. Lower frequency components predominated for most loads and generally increased with increased airspeed, but not necessarily with increased maneuver load factor.

Morris, C. E. K., Jr.↗

NASA NTRS1975

Two-stage fan. 3: Data and performance with rotor tip casing treatment, uniform and distorted inlet flows

A two stage fan with a 1st-stage rotor design tip speed of 1450 ft/sec, a design pressure ratio of 2.8, and corrected flow of 184.2 lbm/sec was tested with axial skewed slots in the casings over the tips of both rotors. The variable stagger stators were set in the nominal positions. Casing treatment improved stall margin by nine percentage points at 70 percent speed but decreased stall margin, efficiency, and flow by small amounts at design speed. Treatment improved first stage performance at low speed only and decreased second stage performance at all operating conditions. Casing treatment did not affect the stall line with tip radially distorted flow but improved stall margin with circumferentially distorted flow. Casing treatment increased the attenuation for both types of inlet flow distortion.

Burger, G. D.↗

NASA NTRS1980

A flight investigation of performance and loads for a helicopter with 10-64C main rotor blade sections

A flight investigation produced data on performance and rotor loads for a teetering rotor, AH-1G helicopter flown with a main rotor that had the NLR-1T airfoil as the blade section contour. The test envelope included hover, forward flight speeds from 34 to 83 m/sec (65 to 162 knots), and collective fixed maneuvers at about 0.25 tip speed ratio. The data set for each test point describes vehicle flight state, control positions, rotor loads, power requirements, and blade motions. Rotor loads are reviewed primarily in terms of peak to peak and harmonic content. Lower frequency components predominated for most loads and generally increased with increased airspeed, but not necessarily with increased maneuver load factor. Detailed data for an advanced airfoil on an AH-1G are presented.

Morris, C. E. K.↗

NASA NTRS1997

Supersonic Quadrupole Noise Theory for High-Speed Helicopter Rotors

High-speed helicopter rotor impulsive noise prediction is an important problem of aeroacoustics. The deterministic quadrupoles have been shown to contribute significantly to high-speed impulsive (HSI) noise of rotors, particularly when the phenomenon of delocalization occurs. At high rotor-tip speeds, some of the quadrupole sources lie outside the sonic circle and move at supersonic speed. Brentner has given a formulation suitable for efficient prediction of quadrupole noise inside the sonic circle. In this paper, we give a simple formulation based on the acoustic analogy that is valid for both subsonic and supersonic quadrupole noise prediction. Like the formulation of Brentner, the model is exact for an observer in the far field and in the rotor plane and is approximate elsewhere. We give the full analytic derivation of this formulation in the paper. We present the method of implementation on a computer for supersonic quadrupoles using marching cubes for constructing the influence surface (Sigma surface) of an observer space- time variable (x; t). We then present several examples of noise prediction for both subsonic and supersonic quadrupoles. It is shown that in the case of transonic flow over rotor blades, the inclusion of the supersonic quadrupoles improves the prediction of the acoustic pressure signature. We show the equivalence of the new formulation to that of Brentner for subsonic quadrupoles. It is shown that the regions of high quadrupole source strength are primarily produced by the shock surface and the flow over the leading edge of the rotor. The primary role of the supersonic quadrupoles is to increase the width of a strong acoustic signal.

Farassat, F.↗

NASA NTRS1987

Acoustic transmissibility of advanced turboprop aircraft windows

Advanced turboprop technology allows propeller aircraft to reach cruise speeds comparable to current jet aircraft yet with considerable fuel savings. Due to the higher blade loading and higher tip speed of these propellers, noise levels of up to 150 dB are expected on the outside of the fuselage in the propeller plane. In this study the transmissibility of triple pane windows, designed to provide 69 dB noise transmission loss at the blade propeller frequency of 164 Hz, was experimentally investigated using insertion loss and three-dimensional intensity techniques. A modal analysis on the outer window panes was conducted to determine pane modal frequencies. Coherence and phase relation of outer panes and window frame were established to obtain double/triple wall and lump mass resonance frequencies. Double/triple wall resonances were found to degrade the transmission loss of the two windows. It was shown that, at the blade passage frequency and the first two overtones, the combinations of window plus scratch shield provide less transmission loss than the average transmission loss of the treated fuselage. Strong disagreement was obtained between the experimental transmission loss of this investigation and the theoretical predictions from another study.

Grosveld, Ferdinand W.↗

NASA NTRS1998

Model Engine Performance Measurement From Force Balance Instrumentation

A large scale model representative of a low-noise, high bypass ratio turbofan engine was tested for acoustics and performance in the NASA Lewis 9- by 15-Foot Low-Speed Wind Tunnel. This test was part of NASA's continuing Advanced Subsonic Technology Noise Reduction Program. The low tip speed fan, nacelle, and an un-powered core passage (with core inlet guide vanes) were simulated. The fan blades and hub are mounted on a rotating thrust and torque balance. The nacelle, bypass duct stators, and core passage are attached to a six component force balance. The two balance forces, when corrected for internal pressure tares, measure the total thrust-minus-drag of the engine simulator. Corrected for scaling and other effects, it is basically the same force that the engine supports would feel, operating at similar conditions. A control volume is shown and discussed, identifying the various force components of the engine simulator thrust and definitions of net thrust. Several wind tunnel runs with nearly the same hardware installed are compared, to identify the repeatability of the measured thrust-minus-drag. Other wind tunnel runs, with hardware changes that affected fan performance, are compared to the baseline configuration, and the thrust and torque effects are shown. Finally, a thrust comparison between the force balance and nozzle gross thrust methods is shown, and both yield very similar results.

Jeracki, Robert J.↗

NASA NTRS1973

Leading edge serrations which reduce the noise of low-speed rotors

Acoustic effects of serrated brass strips attached near the leading edges of two different size rotors were investigated. The two bladed rotors were tested in hover. Rotor rotational speed, blade angle, serration shape, and serration position were varied. The serrations were more effective as noise suppressors at rotor tip speeds less than 135 m/sec (444 ft/sec) than at higher speeds. high frequency noise was reduced but the low frequency rotational noise was little affected. Noise reductions from 4 to 8 db overall sound pressure level and 3 to 17 db in the upper octave bands were achieved on the 1.52 m (5.0 ft) diameter rotor. Noise reductions up to 4 db overall sound pressure level were measured for the 2.59 m (8.5 ft) diameter rotor at some conditions.

Soderman, P. T.↗

NASA NTRS1980

A flight investigation of performance and loads for a helicopter with RC-SC2 main-rotor blade sections

The test envelope included hover, forward-flight speed sweeps from 33 to 74 m/sec (65 to 144 knots), and collective-fixed maneuvers at about 0.25 tip-speed ratio. The data set for each test point describes vehicle flight states, control positions, rotor loads, power requirements and blade motions. Rotor loads were reviewed primarily in terms of peak-to-peak and harmonic content. Lower frequency components predominated for most loads and generally increased with increased airspeed, but not necessarily with increased maneuver load factor.

Morris, C. E. K., Jr.↗

NASA NTRS1986

Effects of planform geometry on hover performance of a 2-meter-diameter model of a four-bladed rotor

Hover tests were conducted on three small scale rotors to evaluate the effects of blade planform taper on rotor hover performance. Tests were conducted on a rectangular swept-tip configuration, on a configuration with a 3 to 1 taper over the outboard 20 percent of the span, and on a configuration with a 5 to 1 taper over the outboard 20 percent of the blade span. The investigation covered a range of thrust coefficients from 0 to 0.0075 and a range of tip speeds from 300 to 600 ft/sec. The tests showed that both tapered configurations had better hover performance than the swept-tip rectangular configuration and that the 3 to 1 taper configuration was better than the 5 to 1 taper configuration. The test results were compared with predictions made with a prescribed wake analysis, a momentum analysis, and a simplified free wake analysis.

Phelps, A. E., III↗

NASA NTRS1973

Noise comparison of two 1.2-pressure-ratio fans with 15 and 42 rotor blades

Two 1.829-m-(6-ft-) diameter fans suitable for a quiet engine for future short-takeoff-and-landing (STOL) aircraft were compared. Both fans were designed for a 1.2 pressure ratio with similar weight flows, thrusts, and tip speeds. The first fan, designated QF-9, had 15 rotor blades and 11 stator blades. The rotor was highly loaded and the tip solidity was less than 1. The QF-9 rotor blades had an adjustable pitch feature which can be used for thrust reversal. The second fan, designated QF-6, operated at a moderate loading with a rotor tip solidity greater than 1. Fan QF-6 had 42 rotor blades and 50 stator blades. The low number of rotor blades for QF-9 reduced the frequency of the blade-passage tone below the range of maximum annoyance. In addition to this difference, the QF-9 fan had a somewhat smaller rotor-stator separation than the QF-6 fan. In terms of sound pressure level and sound power level, QF-9 was the noisier fan, with the power level results for QF-9 being about 1 db above those for QF-6 at equivalent operating points as determined by similar stage pressure ratios. At the same equivalent operating points, the maximum perceived noise along a 152.5-m (500-ft) sideline for QF-9 was about 2.5 PNdb below that for QF-6, which indicated that QF-9 was less objectionable to human hearing.

Woodward, R. P.↗

NASA NTRS1972

Two-Stage Fan I: Aerodynamic and Mechanical Design

A two-stage, highly-loaded fan was designed to deliver an overall pressure ratio of 2.8 with an adiabatic efficiency of 83.9 percent. At the first rotor inlet, design flow per unit annulus area is 42 lbm/sec/sq ft (205 kg/sec/sq m), hub/tip ratio is 0.4 with a tip diameter of 31 inches (0.787 m), and design tip speed is 1450 ft/sec (441.96 m/sec). Other features include use of multiple-circular-arc airfoils, resettable stators, and split casings over the rotor tip sections for casing treatment tests.

Messenger, H. E.↗

NASA NTRS1977

Wind-tunnel tests of wide-chord teetering rotors with and without outboard flapping hinges

Wind tunnel tests of aeroelastically designed helicopter rotor models were conducted to obtain rotor aerodynamic performance and dynamic response data pertaining to two-bladed teetering rotors with a wider chord and lower hover tip speed than currently employed on production helicopters. The effects of a flapping hinge at 62 percent radius were also studied. Finally, the effects of changing tip mass on operating characteristics of the rotor with the outboard flapping hinge were examined. The models were tested at several shaft angles of attack for five advance ratios, 0.15, 0.25, 0.35, 0.40, and 0.45. For each combination of shaft angle and advance ratio, the rotor lift was varied over a wide range to include simulated maneuver conditions. At each test condition, rotor aerodynamic performance and dynamic response data were obtained. From these tests, it was found that wide-chord rotors may be subject to large control forces. An outboard flapping hinge may be used to reduce beamwise bending moments over a significant part of the blade radius without significantly affecting the chordwise bending moments.

Weller, W. H.↗