Search NASA⌕ Search

SEARCH · Search NASA

Results for “Temperature Green function”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Conversion of cellulose to high-yield glucose in water over sulfonated mesoporous carbon fibers with optimized acidity

The hydrolysis of cellulose to high-yield glucose in water remains challenging owing to the limited acidity and substrate contact of sulfonated carbons. In this study, we report a unique sulfonated mesoporous carbon fiber with optimized acidity prepared by the pyrolysis of FeCl 3 -impregnated wipe fibers followed by acid treatment. The Bronsted acidity (especially for SO 3 H) was produced by sulfonation of the magnetic carbon fiber intermediate, while Lewis acidity originated from small Fe 3 O 4 nanoparticles and the remaining defects. The balanced Bronsted and Lewis acidity combined with hydrophilic functionalities was simultaneously tailored by varying the Fe/wipe fiber (WF) feed ratio and pyrolysis temperature to change the porous structure of the final catalysts. The elaborately fabricated MCF-SO 3 H-20-500 (20% Fe/WF feed ratio and pyrolysis at 500 degrees C) delivered 66.0% glucose yield as cellulose was completely converted. This is the highest glucose yield achieved by the hydrolysis of untreated cellulose in water over a sulfonated carbon catalyst. The optimized Bronsted and Lewis acidity was mainly responsible for the controlled conversion of cellulose to glucose, while the rich hydrophilic functionalities and superior mesoporous structure of the catalyst facilitated contact to cellulose and mass transfer. This investigation will open new avenues to design high-performance carbon sulfoacid catalysts toward cellulose hydrolysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Two-color pyrometry based flame to fuel surface radiative heat flux diagnostic using flamelets

In this study, a non-intrusive two-color pyrometry based radiative heat flux diagnostic is presented that accounts for the self-absorption effects. This diagnostic relies on looking up the flame temperature and soot volume fraction using the ratio of color intensities obtained from digital cameras and numerical solutions of 1D steady-state diffusion flames. Virtual two color pyrometry of computed flame show a unique one-to-one mapping of strained flames with intensity ratio; thereby allowing flames to be indexed and creation of a two-color flamelet manifold (TCFM). The TCFM is a function of two variables; the ratio of red to green intensities (flame index) and physical distance to the stoichiometric surface defined using a level-set function. The developed diagnostic is used in upward flame spread experiments where an approximate flame hull reconstruction method is applied to provide the 3D level-set function and intensity ratio for use of TCFM to provide radiative absorption properties for 3D ray tracing. Accounting for self- absorption effects provide improved soot volume fraction estimates. In conclusion, the radiative heat flux estimates are found to be in very good agreement with literature and improved results are obtained near the flame base.

42 ENGINEERING↗

First-principles study of L -shell iron and chromium opacity at stellar interior temperatures

Recently developed free-energy density functional theory (DFT)-based methodology for optical property calculations of warm dense matter has been applied for studying L-shell opacity of iron and chromium at T = 182 eV. We use Mermin–Kohn–Sham density functional theory with a ground-state and a fully temperature-dependent generalized gradient approximation exchange-correlation (XC) functionals. It is demonstrated that the role of XC at such a high-T is negligible due to the total free-energy of interacting system being dominated by the noninteracting free-energy term in agreement with estimations for the homogeneous electron gas. Furthermore, our DFT predictions are compared to the radiative emissivity and opacity of dense plasmas model, to the real-space Greens function method, and to experimental measurements. Good agreement is found between all three theoretical methods, and in the bound–continuum region for Cr when compared to the experiment, while the discrepancy between direct DFT calculations and the experiment for Fe remains essentially the same as for plasma-physics models.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Green synthesis of reduced Ti 3 C 2 T x MXene nanosheets with enhanced conductivity, oxidation stability, and SERS activity

Transition metal carbides (MXenes) are an emerging family of highly conductive two-dimensional materials with additional functional properties introduced by surface terminations. Further modification of the surface terminations makes MXenes even more appealing for practical applications. Herein, we report a facile and environmentally benign synthesis of reduced Ti 3 C 2 T x MXene (r-Ti 3 C 2 T x ) via a simple treatment with L-ascorbic acid at room temperature. r-Ti 3 C 2 T x shows a six-fold increase in electrical conductivity, from 471 ± 49 for regular Ti 3 C 2 T x to 2819 ± 306 S m -1 for the reduced version. Additionally, we show an enhanced oxidation stability of r-Ti 3 C 2 T x as compared to regular Ti 3 C 2 T x . An examination of the surface-enhanced Raman scattering (SERS) activity reveals that the SERS enhancement factor of r-Ti 3 C 2 T x is an order of magnitude higher than that of regular Ti 3 C 2 T x . The improved SERS activity of r-Ti 3 C 2 T x is attributed to the charge transfer interaction between the MXene surface and probe molecules, re-enforced by an increased electronic density of states (DOS) at the Fermi level of r-Ti 3 C 2 T x . The findings of this study suggest that reduced MXene could be a superior choice over regular MXene, especially for the applications that employ high electronic conductivity, such as electrode materials for batteries and supercapacitors, photodetectors, and SERS-based sensors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

QCD Phase Diagram Using Dyson-Schwinger Equations

We describe briefly the Dyson-Schwinger equation approach of QCD and the study of the QCD phase diagram in this approach. The phase diagram in terms of the temperature and chemical potential, and that in the space of coupling strength and current-quark mass are given.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Predicted viscosity of liquid HMX up to 40 GPa

Viscous flow serves as a significant heating mechanism during the formation of hot spots, but the shear viscosity which determines this response is poorly characterized for most high explosives. Most recently, a model was proposed for the shear viscosity of liquid HMX (1,3,5,7-tetranitro-1,3,5,7-tetrazocane) that was fit to pressures reaching 5 GPa, but this work uncovered uncertainties in the viscosity at 0 GPa and remains untested at higher pressures. We use molecular dynamics (MD) simulations and the Green-Kubo formalism to predict the temperature- and pressure-dependent shear viscosity of HMX over the pressure interval 0 GPa≤P≤40 GPa. Reassessment of the viscosity at 0 GPa rules out several potential explanations for discrepancies between earlier reports; we attribute these differences to details of MD trajectory integration impacting molecular flexibility. The shear viscosity of HMX exhibits an Arrhenius temperature dependence at each pressure considered, with exponential prefactor and activation energy terms that are also strong functions of pressure. An analytic form for the viscosity is developed based on an extension of the well-known Andrade equation that simultaneously captures the temperature and pressure dependencies in the MD data up to 40 GPa. Comparison against a recently developed model for the viscosity of liquid RDX (1,3,5-trinitro-1,3,5-triazinane) shows that both materials exhibit similar functional dependencies with the viscosity of HMX being higher by roughly an order of magnitude at a given temperature-pressure state.

36 MATERIALS SCIENCE↗

Moderate temperature sintering of BaZr 0.8 Y 0.2 O 3-δ protonic ceramics by A novel cold sintering pretreatment

The state-of-the-art protonic ceramic conductor BaZr 0.8 Y 0.2 O 3-δ (BZY20) requires an extremely high sintering temperature (≥1700 °C) to achieve the desired relative density and microstructure necessary to function as a proton conducting electrolyte. In this work, we developed a cold sintering pretreatment assisted moderate-temperature sintering method for the fabrication of high-quality pure BZY20 pellets. BZY20 pellets with high relative density of ~94% were fabricated with a final sintering temperature of 1500 °C (200 °C lower than the traditional sintering temperature). A comparison with BZY20 control samples indicated that the proper amount of BaCO 3 introduced on the BZY20 particle surface and the high green density achieved by cold sintering pretreatment were the main drivers for lowering the sintering temperature. The electrical conductivity measurement by electrochemical impedance spectroscopy showed that the as-prepared BZY20 pellets have a proton conductivity comparable to the state-of-the-art values. The cold sintering pretreatment outlined in this work has the potential to lower the sintering temperatures for similar types of protonic ceramic materials under consideration for a wide range of energy conversion and storage applications.

36 MATERIALS SCIENCE↗

Analysis of spin frustration in an Fe III 7 cluster using a combination of computational, experimental, and magnetostructural correlation methods

The synthesis, structure, and magnetic properties are reported for [Fe 7 O 3 (O 2 C t Bu) 9 (mda) 3 (H 2 O) 3 ] ( 1 ), where mdaH 2 is N -methyldiethanolamine. 1 was prepared from the reaction of [Fe 3 O(O 2 C t Bu) 6 (H 2 O) 3 ](NO 3 ) with mdaH 2 in a 1:~3 ratio in MeCN. The core of 1 consists of a central octahedral Fe III ion held within a non-planar Fe 6 loop by three μ 3 -O 2- and three μ 2 -RO - arms from the three mda 2- chelates. Variable-temperature dc and ac magnetic susceptibility studies revealed dominant antiferromagnetic coupling, leading to a ground state spin of S = 5 / 2 . The ground state was confirmed by a fit of magnetization data collected in the 0.1–7.0 T and 1.8–10.0 K ranges. The four Fe 2 pairwise exchange parameters ( J 1 - J 4 ) were estimated by independent methods: theoretical calculations using either broken symmetry energy differences (-46.3, -16.2, -3.9, and - 28.1 cm -1 , respectively) or Green’s function approximation methods (-41.4, -14.8, -13.2, and - 24.7 cm -1 ), and a magnetostructural correlation (MSC) previously developed for high nuclearity Fe III /O complexes (-39.5, -13.8, -6.7, and - 23.5 cm -1 ). Additionally, the J 1 - J 4 obtained from the MSC and theoretical methods were used with the program PHI to both simulate χ M T vs T as well as to serve as reasonable input values to fit the experimental data (-41.0, -11.4, -5.0, and - 27.3 cm -1 ). Analysis of the J ij led to identification of the spin frustration effects operative and the resultant spin vector alignments at each Fe III ion, thus allowing for the rationalization of the experimental ground state.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Combining the ensemble and Franck-Condon approaches for calculating spectral shapes of molecules in solution

The correct treatment of vibronic effects is vital for the modeling of absorption spectra of many solvated dyes. Vibronic spectra for small dyes in solution can be easily computed within the Franck-Condon approximation using an implicit solvent model. However, implicit solvent models neglect specific solute-solvent interactions on the electronic excited state. On the other hand, a straightforward way to account for solute-solvent interactions and temperature-dependent broadening is by computing vertical excitation energies obtained from an ensemble of solute-solvent conformations. Ensemble approaches usually do not account for vibronic transitions and thus often produce spectral shapes in poor agreement with experiment. Here we address these shortcomings by combining zero-temperature vibronic fine structure with vertical excitations computed for a room-temperature ensemble of solute-solvent configurations. In this combined approach, all temperature-dependent broadening is treated classically through the sampling of configurations and quantum mechanical vibronic contributions are included as a zero-temperature correction to each vertical transition. In our calculation of the vertical excitations, significant regions of the solvent environment are treated fully quantum mechanically to account for solute-solvent polarization and charge-transfer. For the Franck-Condon calculations, a small amount of frozen explicit solvent is considered in order to capture solvent effects on the vibronic shape function. We test the proposed method by comparing calculated and experimental absorption spectra of Nile red and the green fluorescent protein chromophore in polar and non-polar solvents. For systems with strong solute-solvent interactions, the combined approach yields significant improvements over the ensemble approach. For systems with weak to moderate solute-solvent interactions, both the high-energy vibronic tail and the width of the spectra are in excellent agreement with experiments

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

IC w22_phadiagractox Highlight: Composition-dependent melting temperature of a compound [Poster]

Figure 1 displays, ambient melting points of the Au-Cu system as a function of Cu atomic percent: present model vs. experimental data from four different sources. Figure 2 displays, ambient melting points of the U-O system as a function of O atomic percent: present model vs. both experiment and quantum molecular dynamics (QMD) simulations on the stoichiometric U-O compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Mechanical creep testing and characterization of Cr coated Zircaloy

Zirconium based cladding has been developed for use in light water reactor fuel applications due to the material’s desirable low neutron scattering cross section. To help improve corrosion resistance in accident conditions, such as a loss of coolant accident (LOCA), a chromium coating can be applied to the outer diameter of the Zircaloy tube. Cladding strength at reactor relevant temperatures is important for the structural performance. Stress relaxation creep testing was performed on Cr coated Zircaloy-4 to measure strain rate as a function of stress for 350 and 650°C. These were performed at both 5 ± 1 % and 7.5 ± 1 % strain. The lower temperature provides results near normal operating temperature, while the higher temperature provides results relevant to off-normal conditions where recrystallization will take place. Characterization was also performed to analyze the structure of the Cr coating and Zircaloy-4 as well as the interface between the two.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Experimental study of the maximum resolution and packing density achievable in sintered and non-sintered binder-jet 3D printed steel microchannels

Developing high resolution 3D printed metallic microchannels is a challenge especially when there is an essential need for high packing density of the primary material. While high packing density could be achieved by heating the structure to the sintering temperature, some heat sensitive applications require other strategies to improve the packing density of primary materials. In this study the goal is to develop high green or pack densities microchannels on the scale of 2-300 microns which have a robust mechanical structure. Binder-jet 3D printing is an additive manufacturing process in which droplets of binder are deposited via inkjet into a bed of powder. By repeatedly spreading thin layers of powder and depositing binder into the appropriate 2D profiles, complex 3D objects can be created one layer at time. Microchannels with features on the order of 500 microns were fabricated via binder jetting of steel powder and then sintered and/or infiltrated with a secondary material. The average particle size of the steel powder was varied along with the droplet volume of the inkjet-deposited binder. The resolution of the process, packing density of the primary material, the subsequent features sizes of the microchannels, and the overall microchannel quality were characterized as a function of particle size distribution, droplet sizes and heat treatment temperatures.

Elliott, Amy M↗

Energy Saving Melting and Revert Reduction (E-SMARRT): Precision Casting of Steel

This project addresses improvements in metal casting processes by reducing scrap and reducing the cost of production, due to scrap reduction from investment casting and yield improvement offered by lost foam casting as compared to no-bake or green sand molding. The objectives for the investment casting portion of the subtask are to improve knowledge of fracture toughness of mold shells and the sources of strength limiting flaws and to understand the effects of wax reclamation procedures on wax properties. Applying 'clean steel' approaches to pouring technology and cleanliness in investment casting of steel are anticipated to improve incoming materials inspection procedures as they affect the microstructure and toughness of the shell. This project focused on two areas of study in the production of steel castings to reduce scrap and save energy: (1) Reducing the amount of shell cracking in investment cast steel production; (2) Investigate the potential of lost foam steel casting The basic findings regarding investment casting shell cracking were: (1) In the case of post pouring cracking, this could be related to phase changes in silica upon cooling and could be delayed by pouring arrangement strategies that maintained the shell surface at temperature for longer time. Employing this delay resulted in less adherent oxidation of castings since the casting was cooler at the time o fair exposure. (2) A model for heat transfer through water saturated shell materials under steam pressure was developed. (3) Initial modeling result of autoclave de-waxing indicated the higher pressure and temperature in the autoclave would impose a steeper temperature gradient on the wax pattern, causing some melt flow prior to bulk expansion and decreasing the stress on the green shell. Basic findings regarding lost foam casting of steel at atmospheric pressure: (1) EPS foam generally decomposes by the collapse mode in steel casting. (2) There is an accumulation of carbon pick-up at the end of the casting opposite the gate. (3) It is recommended that lost foam castings in steel be gated for a quiescent fill in an empty cavity mold to prevent foam occlusion defects from the collapse mode. The energy benefit is primarily in yield savings and lower casting weight per function due to elimination of draft and parting lines for the larger lost foam castings. For the smaller investment casting, scrap losses due to shell cracking will be reduced. Both of these effects will reduce the metal melted per good ton of castings. There will also be less machine stock required per casting which is a yield savings and a small additional energy savings in machining. Downstream savings will come from heavy truck and railroad applications. Application of these processes to heavy truck castings will lighten the heavy truck fleet by about ten pounds per truck. Using ten years to achieve full penetration of the truck fleet at linear rate this will result in a fuel savings of 131 trillion BTU over ten years.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Blue–green afterglow of BaAl{sub 2}O{sub 4}:Dy{sup 3+} phosphors

Highlights: • Afterglow can be achieved when Eu{sup 2+} is absent in the DyAl{sub 2}O{sub 4}:Dy{sup 3+} phosphors. • The afterglow of DyAl{sub 2}O{sub 4}:Dy{sup 3+} phosphors is discernible to naked eyes for minutes. • Dy{sup 3+} introduced trap centers are believed to be responsible for the afterglow. - Abstract: Dy{sup 3+} doped barium aluminate (BaAl{sub 2}O{sub 4}:Dy{sup 3+}) phosphors were prepared via the sol–gel combustion route at the ignition temperature of 600 °C. The phosphors were characterized with X-ray diffractometry, scanning electron microscopy, transmission electron microscopy, photoluminescence spectroscopy, Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. Regardless of the absence of Eu{sup 2+} luminescent centers, broadband blue–green afterglow with its peak at about 490 nm was recorded in the BaAl{sub 2}O{sub 4}:Dy{sup 3+} phosphors. The decay profile of the blue–green afterglow can be best fitted into a two-component exponential function with the two lifetime decay constants to be 8.81 and 45.25 s, respectively. The observation of blue–green afterglow from BaAl{sub 2}O{sub 4}:Dy{sup 3+} in the absence of Eu{sup 2+} provides unique opportunity in unveiling the afterglow mechanisms of rare-earth doped alkaline-metal aluminates. Possible mechanisms on the blue–green afterglow in BaAl{sub 2}O{sub 4}:Dy{sup 3+} phosphors are discussed in terms of the Dy{sup 3+} ions introduced trap centers as well as luminescent centers in the crystal lattice.

36 MATERIALS SCIENCE↗

Experimental realization of classical Z 2 spin liquids in a programmable quantum device

We build and probe a Z 2 spin liquid in a programmable quantum device, the D-Wave DW-2000Q. Specifically, we observe the classical eight-vertex and six-vertex (spin ice) states and transitions between them. To realize this state of matter, we design a Hamiltonian with combinatorial gauge symmetry using only pairwise-qubit interactions and a transverse field, i.e., interactions which are accessible in this quantum device. The combinatorial gauge symmetry remains exact along the full quantum annealing path, landing the system onto the classical eight-vertex model at the endpoint of the path. The output configurations from the device allow us to directly observe the loop structure of the classical model. Moreover, we deform the Hamiltonian so as to vary the weights of the eight vertices and show that we can selectively attain the classical six-vertex (ice) model, or drive the system into a ferromagnetic state. Additionally, we present studies of the classical phase diagram of the system as a function of the eight-vertex deformations and effective temperature, which we control by varying the relative strengths of the programmable couplings, and we show that the experimental results are consistent with theoretical analysis. Finally, we identify additional capabilities that, if added to these devices, would allow us to realize Z 2 quantum spin liquids on which to build topological qubits.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Physical properties of white-light sources in the 2011 February 15 solar flare

White-light flares (WLFs) are observational rarities, making them understudied events. However, optical emission is a significant contribution to flare energy budgets and the emission mechanisms responsible could have important implications for flare models. Using Hinode SOT optical continuum data taken in broadband red, green, and blue filters, we investigate WL emission from the X2.2 flare SOL2011-02-15T01:56:00. We develop a technique to robustly identify enhanced flare pixels and, using a knowledge of the RGB filter transmissions, determined the source color temperature and effective temperature. We investigated two idealized models of WL emission—an optically thick photospheric source, and an optically thin chromospheric slab. Under the optically thick assumption, the color temperature and effective temperature of flare sources in sunspot umbra and penumbra were determined as a function of time and position. Values in the range of 5000-6000 K were found, corresponding to a blackbody temperature increase of a few hundred kelvin. The power emitted in the optical was estimated at ∼10{sup 26} erg s{sup –1}. In some of the WL sources the color and blackbody temperatures are the same within uncertainties, consistent with a blackbody emitter. In other regions this is not the case, suggesting that some other continuum emission process is contributing. An optically thin slab model producing hydrogen recombination radiation is also discussed as a potential source of WL emission; it requires temperatures in the range 5500-25,000 K, and total energies of ∼10{sup 27} erg s{sup –1}.

79 ASTRONOMY AND ASTROPHYSICS↗

Characterization of 430L porous supports obtained by powder extrusion moulding for their application in solid oxide fuel cells

The characterization of 430L stainless steel planar porous supports obtained by powder extrusion moulding was performed in this work. A thermoplastic multicomponent binder based on high density polyethylene and paraffin wax was selected for the process. Green supports were shaped by extrusion moulding, and subsequently the binder was removed by a thermal cycle previously optimized. Sintering was carried out at different temperatures in low vacuum. Density of sintered parts was measured by Archimedes' method and porosity was also evaluated through a microstructural analysis by optical microscopy. The porosity degree of samples sintered at low temperature was close to 35% which is a very suitable value for their application in SOFCs. Tensile tests were carried out in order to determine mechanical strength as a function of porosity degree. Based on these results, the best feedstock composition and processing parameters were selected. The oxidation behaviour in static air at high temperature was studied, and formed oxides were characterized in a scanning electron microscope equipped with energy dispersive analysis of X-rays. X-ray diffraction experiments were performed in order to identify the formed oxides based on formula Fe{sub 2−x}Cr{sub x}O{sub 3}. The results of these studies showed that this kind of ferritic stainless steel would be more suitable to be used as anodic supports where a rich hydrogen atmosphere is employed. Preliminary deposition tests allowed obtaining a homogeneous Ni–YSZ anode layer with a thickness of 10 μm on the porous metallic substrates. - Highlights: • 430L stainless steel porous supports were obtained by powder extrusion moulding. • Porosity degree was controlled sintering at different temperatures in low vacuum. • Tensile tests allowed determining mechanical strength of porous supports. • A study about its oxidation behaviour in static air at high temperature was realized. • After oxidation, formed oxides were characterized by EDS–SEM and XRD.

36 MATERIALS SCIENCE↗

Full-wave simulations of ICRF heating regimes in toroidal plasmas with non-Maxwellian distribution functions

At the power levels required for significant heating and current drive in magnetically-confined toroidal plasma, modification of the particle distribution function from a Maxwellian shape is likely [T. H. Stix, Nucl. Fusion, 15 737 (1975)], with consequent changes in wave propagation and in the location and amount of absorption. In order to study these effects computationally, both the finite-Larmor-radius and the high-harmonic fast wave (HHFW), versions of the full-wave, hot-plasma toroidal simulation code TORIC [M. Brambilla, Plasma Phys. Control. Fusion 41, 1 (1999) and M. Brambilla, Plasma Phys. Control. Fusion 44, 2423 (2002)], have been extended to allow the prescription of arbitrary velocity distributions of the form f(v||, v_perp, psi , theta). For hydrogen (H) minority heating of a deuterium (D) plasma with anisotropic Maxwellian H distributions, the fractional H absorption varies significantly with changes in parallel temperature but is essentially independent of perpendicular temperature. On the other hand, for HHFW regime with anisotropic Maxwellian fast ion distribution, the fractional beam ion absorption varies mainly with changes in the perpendicular temperature. The evaluation of the wave-field and power absorption, through the full wave solver, with the ion distribution function provided by either aMonte-Carlo particle and Fokker-Planck codes is also examined for Alcator C-Mod and NSTX plasmas. Non-Maxwellian effects generally tends to increase the absorption with respect to the equivalent Maxwellian distribution.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗