Search NASA⌕ Search

SEARCH · Search NASA

Results for “Time at temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

In-flight boundary-layer measurements on a hollow cylinder at a Mach number of 3.0

Skin temperatures, shear forces, surface static pressures, boundary layer pitot pressures, and boundary layer total temperatures were measured on the external surface of a hollow cylinder that was 3.04 meters long and 0.437 meter in diameter and was mounted beneath the fuselage of the YF-12A airplane. The data were obtained at a nominal free stream Mach number of 3.0 (a local Mach number of 2.9) and at wall to recovery temperature ratios of 0.66 to 0.91. The local Reynolds number had a nominal value of 4,300,000 per meter. Heat transfer coefficients and skin friction coefficients were derived from skin temperature time histories and shear force measurements, respectively. In addition, boundary layer velocity profiles were derived from pitot pressure measurements, and a Reynolds analogy factor was obtained from the heat transfer and skin friction measurements. The measured data are compared with several boundary layer prediction methods.

Quinn, R. D.↗
NASA NTRS1981

Experimental determination of the effects of moisture on composite-to-composite adhesive joints

The primary mode of moisture ingress into bonded composite joints is determined using a nuclear probe for deuterium (NPD) to measure the localized D2O content along the length of the adhesive (FM-300 and EA-9601) and through the thickness of bonded composite speciments. Calculated diffusivities and NPD measured equilibrium moisture contents are used to predict the moisture profiles along the length of the adhesives as a function of exposure time, temperature, and relative humidity. These results are compared with the observed moisture profiles to evaluate the extent of enhanced edge diffusion. The FM-300 adhesive exhibits good agreement between measured and predicted profiles at 49 C, 70% and 90% RH, and 77 C, 70% RH. At 77 C, 90% RH, the measured moisture content near the adhesive edge is substantially larger than the predicted level. The EA-9601 adhesive also shows good agreement at 49 C, 70% and 90% RH, but at 77 C, the concentration of D20 near the edges is enhanced at each humidity level. The effect of moisture content on the bond shear strength at room temperature and at elevated temperature is evaluated.

Deiasi, R. J.↗
NASA NTRS1980

Electrostatic bonding of thin (approximately 3 mil) 7070 cover glass to Ta2O5 AR-coated thin (approximately 2 mil) silicon wafers and solar cells

Electrostatic bonding (ESB) of thin (3 mil) Corning 7070 cover glasses to Ta2O5 AR-coated thin (2 mil) silicon wafers and solar cells is investigated. An experimental program was conducted to establish the effects of variations in pressure, voltage, temperature, time, Ta2O5 thickness, and various prebond glass treatments. Flat wafers without contact grids were used to study the basic effects for bonding to semiconductor surfaces typical of solar cells. Solar cells with three different grid patterns were used to determine additional requirements caused by the raised metallic contacts.

Egelkrout, D. W.↗
NASA NTRS1981

Space Shuttle Orbiter flight heating rate measurement sensitivity to thermal protection system uncertainties

A study was completed to determine the sensitivity of computed convective heating rates to uncertainties in the thermal protection system thermal model. Those parameters considered were: density, thermal conductivity, and specific heat of both the reusable surface insulation and its coating; coating thickness and emittance; and temperature measurement uncertainty. The assessment used a modified version of the computer program to calculate heating rates from temperature time histories. The original version of the program solves the direct one dimensional heating problem and this modified version of The program is set up to solve the inverse problem. The modified program was used in thermocouple data reduction for shuttle flight data. Both nominal thermal models and altered thermal models were used to determine the necessity for accurate knowledge of thermal protection system's material thermal properties. For many thermal properties, the sensitivity (inaccuracies created in the calculation of convective heating rate by an altered property) was very low.

Bradley, P. F.↗
NASA NTRS1980

Contact integrity testing of stress-tested silicon terrestrial solar cells

A test procedure was developed and applied to terrestrial silicon solar cells in order to determine the effect of accelerated environmental and time-temperature aging on metal contact integrity. Quantities of cells of four different manufacturers were given the contact integrity test after being subjected to accelerated stress tests that included forward bias-temperature, thermal cycle and thermal shock, power cycle, and bias-temperature humidity tests at two temperature-humidity levels. Significant effects due to certain stress tests were found for some cell types. It is concluded that cells fabricated using plated nickel/solder metallization showed significantly more serious contact integrity degradation than silver-metallized cells.

Prince, J. L.↗
NASA NTRS1981

Long-time stress relaxation of a filled elastomer in vacuum environments

Samples of a filled elastomeric ablative material were stored at 45 C and 10 to the -6th torr for 7 months. Their tensile stress-relaxation modulus at constant strain was measured throughout the 7 months. Results of the testing are discussed primarily by comparisons of the data to atmospheric-pressure moduli (determined in this work for shorter periods of time) and with moduli predicted from short-time testing. Confirmation of the strengthening effects of vacuum on this composite was obtained. The use of time-temperature superposition techniques as an approximate accelerated testing procedure for this material under these conditions was also verified.

Ward, T. C.↗
NASA NTRS1981

Elevated temperature fatigue testing of metals

Material characterization and evaluation conducted for the purpose of calculating fatigue crack initiation lives of components operating at elevated temperatures are discussed. The major technology areas needed to perform a life prediction of an aircraft turbine engine hot section component and the steps required for life prediction are outlined. These include: the determination of the operating environment, the calculation of the thermal and mechanical loading of the component, the cyclic stress strain and creep behavior of the material required for structural analysis, the structural analysis to determine the local stress strain temperature time response of the material at the critical location in the component, and from a knowledge of the fatigue, creep, and failure resistance of the material, a prediction of the life of the component.

Hirschberg, M. H.↗
NASA NTRS1981

Transient catalytic combustor model

A quasi-steady gas phase and thermally thin substrate model is used to analyze the transient behavior of catalytic monolith combustors in fuel lean operation. The combustor response delay is due to the substrate thermal inertia. Fast response is favored by thin substrate, short catalytic bed length, high combustor inlet and final temperatures, and small gas channel diameters. The calculated gas and substrate temperature time history at different axial positions provides an understanding of how the catalytic combustor responds to an upstream condition change. The computed results also suggest that the gas residence times in the catalytic bed in the after bed space are correlatable with the nondimensional combustor response time. The model also performs steady state combustion calculations; and the computed steady state emission characteristics show agreement with available experimental data in the range of parameters covered. A catalytic combustor design for automotive gas turbine engine which has reasonably fast response ( 1 second) and can satisfy the emission goals in an acceptable total combustor length is possible.

Tien, J. S.↗
NASA NTRS1981

Preflight reentry heat transfer analysis of Space Shuttle

Preflight predictions of the structural temperature distributions during entry are compared with data from the initial Shuttle flight. Finite element thermal analysis programming was used to model the heat flow on Shuttle structures and actual gas properties of air were employed in the analyses of aerodynamic heating. Laminar, separated, and turbulent heat fluxes were calculated for varying locations on the craft using velocity-attitude and angle-of-attack projections taken from the nominal STS-1 trajectory. Temperature time histories of the first flight are compared with laminar and turbulent flow assumptions and an unpredicted rapid cooling 1800 sec into entry is credited to inaccurate assumptions of structural heat dissipative properties or flow conditions in that time phase of the flight; additional discrepancies in descriptions of heating of the upper fuselage are attributed to a lack of knowledge of the complex flow patterns existing over that area of the Shuttle body.

Ko, W. L.↗
NASA NTRS1981

Comparison of Michigan Basin crude oils

Michigan Basin oils from the Ordovician Trenton, Silurian Niagaran, and Devonian Dundee formations have been geochemically compared by GC, GC-MS, and carbon isotope mass spectrometry. One oil from each formation was selected for detailed analysis which included measurement of individual n-alkane delta 13 C values. The Ordovician and Devonian oils are strikingly similar to one another, yet clearly different from the Silurian oil. This pattern is unexpected because Ordovician and Devonian reservoirs are physically separated by the Silurian strata. From time-temperature considerations, the Devonian oil probably was formed in older strata and has migrated to its present location. Our analyses suggest a common source for the Devonian and Ordovician oils.

Vogler, E. A.↗
NASA NTRS1981

The viscoelastic response of a graphite/epoxy laminate

An accelerated characterization procedure has been developed for time-dependent compliances and strengths of resin-matrix composites. The procedure, which is based on a time-temperature-stress superposition principle, is applied to a graphite/epoxy laminate T300/934. Creep rupture analytical models are discussed, and model predictions are compared with experimental data. Master curves for the creep compliances are given.

Brinson, H. F.↗
NASA NTRS1982

Comparisons of free-flight experimental and predicted heating rates for the Space Shuttle

Experimental windward-ray heating rates measured during entry of the first Space Shuttle Orbiter mission are compared with predicted rates based on engineering and detailed equilibrium-air analyses. The experimental heating rates were reduced from temperature-time histories which are available only for the trajectory period after blackout which corresponds to a freestream Mach number and altitude of approximately 11.0 and 53 km, respectively. The experimental heating rates are computed for two measured emissivity data sets. The differences in the experimental heating rates based on the two emissivity data sets are sufficiently large that different interpretations of the STS-1 aerothermal environment may be inferred.

Zoby, E. V.↗
NASA NTRS1982

Twenty three year cycle in surface temperatures during the Maunder minimum

Power spectra of Manley's record of central England temperatures for the Maunder minimum have been compared with later periods. It is found that the power in the approximately 23 year cycle is statistically significant in the Maunder minimum portion of this temperature time series. This gives indirect support to the recent suggestion that the solar cycle persisted in the Maunder minimum even though normal sunspot activity was not observed. The results also indicate that the approximately 23 year cycle was stronger during the Maunder minimum than later times in this record.

Hameed, S.↗
NASA NTRS1982

Thermal periodicities in the Venus atmosphere

Evidence of periodic fluctuations was sought in the Pioneer Venus orbiter's IR radiometer data by averaging it in 10 X 10 deg latitude-longitude bins for each of the 72 days during which the instrument was in operation. The thermal brightness temperature time series obtained was then analyzed to determine the amplitude of fluctuations at periods ranging from two to 64 days, for cloud-top, 70, 80 and 90 km levels in the atmosphere. It is found that fluctuation amplitudes, which are small at equatorial latitudes, increase to a maximum at 60-70 deg latitude and reach a maximum at the cloud-top level, decreasing to a minimum at the 80 km channel before increasing again toward the 90 km channel. The period of the highest amplitude fluctuation is found to be 5.3 + or - 0.4 days, at all altitudes except at 70-80 deg latitude, where a 2.9-day period which may correspond to the polar dipole dominates the cloud-top channel.

Apt, J.↗
NASA NTRS1982

Process research on non-CZ silicon material

High risk, high payoff research areas associated with he process for producing photovoltaic modules using non-CZ sheet material are investigated. All investigations are being performed using dendritic web silicon, but all processes are directly applicable to other ribbon forms of sheet material. The technical feasibility of forming front and back junctions in non-CZ silicon using liquid dopant techniques was determined. Numerous commercially available liquid phosphorus and boron dopant solutions are investigated. Temperature-time profiles to achieve N(+) and P(+) sheet resistivities of 60 + or - 10 and 40 + or - s10 ohms per square centimeter respectively are established. A study of the optimal method of liquid dopant application is performed. The technical feasibility of forming a liquid applied diffusion mask to replace the more costly chemical vapor deposited SiO2 diffusion mask was also determined.

Source record↗
NASA NTRS1983

The NBS: Processing/Microstructure/Property Relationships in 2024 Aluminum Alloy Plates

As received plates of 2024 aluminum alloy were examined. Topics covered include: solidification segregation studies; microsegregation and macrosegregation in laboratory and commercially cast ingots; C-curves and nondestructive evaluation; time-temperature precipitation diagrams and the relationships between mechanical properties and NDE measurements; transmission electron microscopy studies; the relationship between microstructure and properties; ultrasonic characterization; eddy-current conductivity characterization; the study of aging process by means of dynamic eddy current measurements; and Heat flow-property predictions, property degradations due to improve quench from the solution heat treatment temperature.

Ives, L. K.↗
NASA NTRS1983

Low cycle fatigue behavior of aluminum/stainless steel composites

Composites consisting of an aluminum matrix reinforced with various volume fractions of stainless steel wire were fabricated by hot die pressing under various conditions of temperature, time, and pressure. The composites were tested in plane bending to complete fracture under cycle loading, and the results were analyzed on a computer to obtain a statistically valid mathematical relationship between the low-cycle fatigue life and the fiber volume fraction of the composite. The fractured surfaces of the composites were examined by scanning electron microscopy to identify the characteristic features of fatigue damage. Fatigue damage mechanisms are proposed and discussed.

Bhagat, R. B.↗
NASA NTRS1983

Variable anodic thermal control coating on aluminum

A variable thermal control coating (modified chromic acid anodizing) has been developed to meet the needs for the thermal control of spacecraft. This coating, with controlled variable ranges of 0.10 to 0.72 thermal emittance and 0.2 to 0.4 solar absorptance, allows the user to select any value of thermal emittance and solar absorptance within the range specified and obtain both values within + or - 0.02. Preliminary solar stability has shown less than 15 percent degradation over 2000 hours of vacuum solar exposure. The technique has been determined to be sensitive to the parameters of voltage, rate of voltage application, time, temperature, acid concentration, and material pretreatment.

Duckett, R. J.↗