Search NASA⌕ Search

SEARCH · Search NASA

Results for “Tunnel Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

An analytical study and wind tunnel tests of an aeromechanical gust-alleviation system for a light airplane

The results of an analytical study of a system using stability derivatives determined in static wind tunnel tests of a 1/6 scale model of a popular, high wing, light airplane equipped with the gust alleviation system are reported. The longitudinal short period mode dynamics of the system are analyzed, and include the following: (1) root loci, (2) airplane frequency responses to vertical gusts, (3) power spectra of the airplane responses in a gust spectrum, (4) time history responses to vertical gusts, and (5) handling characteristics. The system reduces the airplane's normal acceleration response to vertical gusts while simultaneously increasing the pitching response and reducing the damping of the longitudinal short period mode. The normal acceleration response can be minimized by using the proper amount of static alleviation and a fast response system with a moderate amount of damping. The addition of a flap elevator interconnect or a pitch damper system further increases the alleviation while moderating the simultaneous increase in pitching response. The system provides direct lift control and may reduce the stick fixed longitudinal static stability.

Stewart, E. C.↗
NASA NTRSDate not supplied

Aeroservoelastic Control Law Development for the Integrated Adaptive Wing Technology Maturation Wind-Tunnel Test

In this paper, a linear quadratic Gaussian (LQG) regulator was applied to a computational aeroservoelastic (ASE) model of the Integrated Adaptive Wing Technology Maturation (IAWTM) wind-tunnel model to demonstrate its effectiveness for active flutter suppression. The aerodynamics within this computational ASE model were solved using unsteady Reynolds-averaged Navier-Stokes (RANS) equations; the structural dynamics of the model were solved using modal analysis. This RANS-based ASE model was used as the plant for the LQG regulator. The Kalman filter and controller used within the LQG regulator were derived from a reduced-order model (ROM) of the RANS-based ASE model. This ROM-based ASE model was generated using system identification techniques. It was shown that the Kalman filter adequately predicted important states of the plant, and that LQG regulator successfully stabilized an aeroelastically unstable plant without exceeding reasonable control surface limitations. All of this was demonstrated using simulation data, and the methods presented here appear feasible for use in the upcoming IAWTM wind-tunnel tests.

Josiah M. Waite↗
NASA NTRS1974

Wind tunnel test of model target thrust reversers for the Pratt and Whitney aircraft JT8D-100 series engines installed on a 727-200 airplane

The results of a low speed wind tunnel test of 0.046 scale model target thrust reversers installed on a 727-200 model airplane are presented. The full airplane model was mounted on a force balance, except for the nacelles and thrust reversers, which were independently mounted and isolated from it. The installation had the capability of simulating the inlet airflows and of supplying the correct proportions of primary and secondary air to the nozzles. The objectives of the test were to assess the compatibility of the thrust reversers target door design with the engine and airplane. The following measurements were made: hot gas ingestion at the nacelle inlets; model lift, drag, and pitching moment; hot gas impingement on the airplane structure; and qualitative assessment of the rudder effectiveness. The major parameters controlling hot gas ingestion were found to be thrust reverser orientation, engine power setting, and the lip height of the bottom thrust reverser doors on the side nacelles. The thrust reversers tended to increase the model lift, decrease the drag, and decrease the pitching moment.

Hambly, D.↗
NASA NTRS1973

The results of low-speed wind tunnel tests to investigate the effects of the NASA refan JT8D engine nacelles on the stability and control characteristics of the Boeing 727-200

The results from two low-speed wind tunnel tests of the Boeing 727-200 airplane as configured with the NASA refan JT8D-109 turbofan engines are presented. The objective of these tests was to determine the effects of the refan installation on the low-speed stability and control characteristics of the 727 airplane. Four side nacelle locations were tested to insure that aerodynamic interactions of the nacelles and empennage would be optimized. The optimum location was judged to be the same as that of the production JT8D-9 engines; the current production engine mounts can be used for this location. Some small changes in the basic airplane characteristics are attributable to the refan nacelles. The flaps up longitudinal and lateral-directional stability are both slightly increased for low angles of attack and sideslip respectively. The longitudinal stability at stall is improved for both the flaps up and landing flap configurations. The high attitude characteristics of the basic airplane are not significantly altered by the refan nacelle installation. Directional control capability is not affected by the refan nacelles.

Shirkey, M. D.↗
NASA NTRS1976

Some theoretical considerations of longitudinal stability in power-on flight with special reference to wind-tunnel testing, November 1942

Some problems relating to longitudinal stability in power-on flight are considered. A derivation is included which shows that, under certain conditions, the rate of change of the pitching moment coefficient with lift coefficient as obtained in wind tunnel tests simulating constant power operation is directly proportional to one of the indices of stability commonly associated with flight analysis, (the slope of the curve relating the elevator angle for trim and lift coefficient). The necessity of analyzing power-on wind tunnel data for trim conditions is emphasized, and a method is provided for converting data obtained from constant thrust tests to simulated constant throttle flight conditions.

Donlan, C. J.↗
NASA NTRS1981

Curved-flow, rolling-flow, and oscillatory pure-yawing wind-tunnel test methods for determination of dynamic stability derivatives

Dynamic stability derivatives are evaluated on the basis of rolling-flow, curved-flow and snaking tests. Attention is given to the hardware associated with curved-flow, rolling-flow and oscillatory pure-yawing wind-tunnel tests. It is found that the snaking technique, when combined with linear- and forced-oscillation methods, yields an important method for evaluating beta derivatives for current configurations at high angles of attack. Since the rolling flow model is fixed during testing, forced oscillations may be imparted to the model, permitting the measurement of damping and cross-derivatives. These results, when coupled with basic rolling-flow or rotary-balance data, yield a highly accurate mathematical model for studies of incipient spin and spin entry.

Chambers, J. R.↗
NASA NTRS1979

Integration Time Required to Extract Accurate Data from Transonic Wind-Tunnel Tests

Because the forces and pressures on wind-tunnel models tested at transonic speeds are not steady, even for static aerodynamic tests, integration time is required to obtain data of acceptable accuracy. The integration time required for both static and dynamic tests is evaluated analytically and confirmed by experimental measurements. It is shown that, for static and dynamic tests, the accuracy obtained is a function of integration time, frequency of the signal, and the ratio of the dynamic amplitude to the full signal of interest. In addition, for the dynamic case, the frequency bandwidth used in analysis is important. Results of this study indicate that, for typical data accuracy desired from models in a large transonic wind tunnel (11- by 11-ft), up to the following integration times are required: static force and moment tests, 0.5 s; static pressure tests, 1 s; flutter tests, 30 to 60 s; and random-dynamic tests, 10 s.

Muhlstein, Lado, Jr.↗
NASA NTRS1975

Integration time required to extract accurate static and dynamic data from transonic wind-tunnel tests

Because the forces and pressures on wind-tunnel models tested at transonic speeds are not steady, even for 'static' aerodynamic tests, integration time is required to obtain data of acceptable accuracy. The integration time required for both static and dynamic tests is evaluated analytically and confirmed by experimental measurements. It is shown that, for static and dynamic tests, the accuracy obtained is a function of integration time, frequency content of the signal, and the ratio of the dynamic amplitude to the full signal of interest. In addition, for the dynamic case, the frequency band width used in analysis is important. Results of this study indicate that, for typical data accuracy desired from models in a large transonic wind tunnel (11- by 11-ft), up to the following integration times are required: static force and moment tests, 0.5 sec; static pressure tests, 0.1 sec; flutter tests, 30 to 60 sec; and random-dynamic tests, 10 sec.

Muhlstein, L., Jr.↗
NASA NTRS1984

Wind tunneling testing and analysis relating to the spinning of light aircraft

Included is a summary of two studies related to the spinning of light aircraft. The first study was conducted to demonstrate that the aerodynamic forces and moments acting on a tail of a spinning aircraft can be obtained from static wind-tunnel tests. The second study analytically investigated spinning using a high angle-of-attack aerodynamic model derived from a static wind-tunnel data base. The validity of the aerodynamic model is shown by comparisons with rotary-balance data and forced-oscillation tests. The results of a six-degree-of-freedom analysis show that the dynamics and aerodynamics of the steep- and flat-spin modes of a modified Yankee have been properly modeled.

Mccormick, B. W.↗
NASA NTRS1974

Wind tunnel tests of a full-scale model of a light twin-engine airplane with fixed auxiliary airfoil or leading-edge slot

An investigation has been conducted by means of wind-tunnel tests of a full-scale mockup of a light twin-engine airplane configuration to determine the effects of outboard partial-span slots and of auxiliary airfoils ahead of the leading edge of the wing in improving aerodynamic characteristics at high angles of attack. Both of the stall-control devices gave considerable improvement in high angle-of-attack characteristics with the auxiliary airfoil giving the more favorable results, but neither device performed as well as might have been expected.

Fink, M. P.↗
NASA NTRS1976

A low speed wind tunnel test of a 0.050 scale model of shuttle orbiter (model 089B) to investigate the longitudinal and lateral directional effects of canard and tail configurational modifications in the LTV LSWT (MA14)

A low speed wind tunnel test was conducted to determine the effects of 6 canard configurations on the 0.050 scale model of shuttle orbiter 089B. In addition, two horizontal tail configurations were tested at two positions on the model as were two wing configurations. Since this test was restricted to 103 runs, only a limited number of permutations of the configurational changes could be tested. The testing was done in the 15 by 20 foot section of the LSWT and consisted of pitch polars, one yawed polar and several yaw runs. The pitch polars encompassed an alpha range from 0 to 28 deg; the yawed polar was run at beta = +2 degrees and the yaw runs covered a beta range from -6 to +6 deg at angles-of-attack of 0, 4, 10, 16, and 20 deg.

Chambliss, E. B.↗
NASA NTRS1981

Statistical model to perform error analysis of curve fits of wind tunnel test data using the techniques of analysis of variance and regression analysis

The considered research had the objective to design a statistical model that could perform an error analysis of curve fits of wind tunnel test data using analysis of variance and regression analysis techniques. Four related subproblems were defined, and by solving each of these a solution to the general research problem was obtained. The capabilities of the evolved true statistical model are considered. The least squares fit is used to determine the nature of the force, moment, and pressure data. The order of the curve fit is increased in order to delete the quadratic effect in the residuals. The analysis of variance is used to determine the magnitude and effect of the error factor associated with the experimental data.

Alston, D. W.↗
NASA NTRS1985

Free-tip-rotor wind-tunnel test results

Seven controller mechanisms and several tip geometries were proposed and evaluated in the course of a free tip rotor development program which integrated those components into a model rotor system for wind tunnel testing. After a rigid whirl test was run to determine controller mechanism performance and structural integrity, a second whirl test was performed with a model rotor incorporating a selected controller design and a selected tip platform to determine the transient behavior of the tips in response to aerodynamic excitation. The results obtained demonstrate that a swept, tapered tip with a tension-torsion strap controller furnished satisfactory mechanical operation, achieved the specified output torque, possessed a low spring rate, and had fast and stable response to excitation.

Stroub, R. H.↗
NASA NTRS1986

Wind tunnel test evaluation of a Shuttle derived launch system

The Shuttle Derived Vehicle (SDV) is a proposed unmanned launch system configured using Shuttle elements. The SDV incorporates two solid rocket boosters, an external tank and three Space Shuttle main engines identical to those used in the present Space Transportation System. Two new elements, a recoverable propulsion/avionics module housing the main engines and an expendable payload module, complete the SDV configuration. This paper describes the activities and results of wind tunnel tests conducted to validate the aerodynamic and controllability characteristics of SDV configurations. The configuration variables consisted of the payload module diameter, length and nose shape. The tests were conducted in the NASA/Marshall Space Flight Center 14 inch trisonic wind tunnel. Aerodynamic force and moment data were obtained over a Mach number range of 0.6 to 4.96. The attack and sideslip angles were varied + or - 8.0 deg. Forces and moments were measured by a sting-supported six component strain gage balance.

Tewell, J. R.↗
NASA NTRS1995

Low-Speed Wind Tunnel Tests of Two Waverider Configuration Models

A definitive measurement of the low-speed flight characteristics of waverider-based aircraft is required to augment the overall design database for this important class of vehicles which have great potential for efficient high-speed flight. Two separate waverider-derived vehicles were tested; one in the 14- by 22-Foot Tunnel and the other in the 12-Foot Low Speed Tunnel at Langley Research Center. These tests provided measurements of moments and forces about all three axes, control effectiveness, flow field characteristics and the effects of configuration changes. The results of these tunnel tests are summarized and the subsonic aerodynamic characteristics of the two configurations are shown.

Pegg, Robert J.↗
NASA NTRS2019

Space Launch System Aeroacoustic Wind Tunnel Test Results

Characterization of accurate launch vehicle unsteady aerodynamics is critical for component and secondary structure vibroacoustic design. For the National Aeronautics and Space Administration (NASA) Space Launch System (SLS), aeroacoustic environments have been derived primarily through sub-scale wind tunnel testing. Both optical techniques and high frequency pressure measurements have been utilized across multiple testing facilities and numerous vehicle configurations to develop a range of preliminary and detailed environments. As the vehicle has matured and evolved, the data collected from each subsequent configuration has allowed for comparison studies which isolate the effects of certain outer mold line (OML) features on measured fluctuating pressure levels. This paper presents observations on some of those effects for features which include abort system protuberances, various fairings geometries, interstage flanges, and multibody interactions between a central core and fall away boosters. These features, and the flow conditions produced by them, are broadly applicable to many launch vehicle configurations.

Steva, Thomas B.↗
NASA NTRS1992

A hypersonic shock tunnel test of the Aeroassist Flight Experiment (AFE) vehicle at high altitude test conditions

The Aeroassist Flight Experiment (AFE) vehicle is a 4.26 m-diameter raked and blunted elliptic cone that is intended to obtain aerodynamic and aerothermodynamic data on blunt bodies at velocities near 10 km/s and altitudes above 75 km. Previous wind tunnel tests of this configuration have been at Mach numbers of 10 or lower. The present test program consisted of five test conditions at Mach numbers between 15 and 20 and simulated altitudes from 75 km to 97 km. Static longitudinal aerodynamic coefficients, the lift-to-drag ratio, and the trim angle-of-attack were obtained for angles-of-attack between 7 deg and 27 deg. The effects of angle-of-attack and shock Reynolds number, Re2, have been studied. These results indicate the AFE configuration is longitudinally stable. The variation of normal force slope, CNalpha and lift-to-drag slope, (L/D)alpha as well as the trim angle-of-attack with Re2 are documented. The trim angle-of-attack increases with decreasing values of shock Reynolds number (increasing altitude) while the lift-to-drag ratio at the trimmed conditions is relatively constant.

Wittliff, C. E.↗