Search NASA⌕ Search

SEARCH · Search NASA

Results for “Waste Processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Coal-Waste-Enhanced Filaments for Additive Manufacturing of High-Temperature Plastics and Ceramic Composites

In the United States, coal waste from over a century of mining and burning coal for heat and electricity has accumulated as mountains of coal fly ash and bottom ash and acre-size ponds, coal fines and gob. These materials can be a problem for local communities and water systems. A cost-effective process to utilize high volumes of these coal wastes in a high-value product would be beneficial to those communities by reducing the amount of waste and providing jobs, manufacturing components, and materials from the waste. Many coal-to-products technologies (e.g., carbon fibers, graphene, carbon foam) rely on carefully choosing the starting material and then altering it chemically or thermally to make the products work. Due to the wide variability of composition and coal content in typical coal waste streams, many high-volume coal waste streams are likely to be unsuitable for use in those technologies. Semplastics’ technology has been shown to utilize most types of coal waste successfully without any pre-selection or pre-processing requirements other than a nominal particle-size reduction for wastes like bottom ash. This characteristic of Semplastics’ solution may enable the use of much larger volumes of a wider range of coal wastes than other coal-to-products technologies. In this project, Semplastics leveraged its unique experience with both coal waste (fly ash or coal combustion residuals), resin materials, and 3D printing to develop 3D printer filaments using common coal wastes – bituminous coal fines and fly ash – and researched the feasibility of using other forms of coal waste as fillers. Simple 3D-printed parts were successfully produced from the coal waste enhanced filaments, which were found to have improved strength and stiffness.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2026

Developing a Process for Collaboration-Based Siting of a Federal Consolidated Interim Storage Facility in the United States: Learning from Communities Living with Legacy Waste

In June of 2023, the U.S. Department of Energy (DOE), Office of Nuclear Energy (NE) announced the selection of its Collaboration-Based Siting (CBS) Consortia, a group of 12 awardees, including the Consortium for Risk Evaluation with Stakeholder Participation (CRESP) (led by Vanderbilt University) to assist DOE-NE with the development of its process for siting a federal consolidated interim storage facility (FCISF) for spent nuclear fuel (SNF) storage. At this time, DOE NE is not soliciting interested host communities, rather the CBS Consortia are tasked with in-depth engagement, mutual learning, and capacity building to provide DOE NE with feedback on the CBS process. CRESP’s objective is to engage communities in two regions (the Pacific Northwest and the Southeast) with sites currently storing defense- and research-related SNF to foster learning concerning the best and worst practices in community participation in risk-informed decision making. This includes learning from existing structures for public input in radioactive waste management decision making [e.g. citizen advisory boards (CABs)] and other local parties about how to build and sustain trust among the parties. CRESP has been working to engage stakeholders and Tribes surrounding two DOE sites historically differing in receptiveness to engaging with DOE and trusting in DOE to accomplish its missions. CRESP’s approach to date has consisted of (1) engaging voluntarily members and former members of the DOE Office of Environmental Management’s CABs to develop a mutual understanding of their perspectives, values, and experiences related to risk and participatory decision making; (2) engaging members of those communities that would likely be part of any radioactive waste management discussions and who may provide valuable feedback for the development of the CBS process; and in the longer term, (3) engaging communities to foster knowledge sharing on understanding and definitions of risk and how risk is factored into community decision making. Our emphasis is to identify opportunities for improving risk communication frameworks, strategies, and decision making. The selection of a future FCISF site is likely to result in the creation of a structure similar to a CAB composed of members of the local community. We anticipate that these insights can help DOE NE learn from existing participatory risk communication structures in place at sites storing defenseor research-related SNF to understand best practices for fostering enduring and participatory relationships with future CABs. Within this paper, we (1) describe CRESP’s overall approach to assisting DOE NE with maturing the CBS process; (2) present a summary of preliminary phase 1 project results, including the development of a body of knowledge (describing available resources to support community engagement, risk communica tion, and participatory decision making) and community ecosystem information (leveraging demographic, social, economic, and environmental attribute mapping and advanced sentiment analysis of social media data); and (3) based on these results, provide observations for future research opportunities to support the development of CBS processes for radioactive waste management facilities, generally.

collaboration-based siting↗
DOE OSTI2025

Upcycling of Waste Plastics into Carboxylic Acids for Biodegradable Surfactants

This work outlines a process for producing high‐purity (>95%) carboxylate surfactants from post‐consumer recycled high‐density polyethylene (PCR‐HDPE). The approach involves the thermal depolymerization of PCR‐HDPE via pyrolysis, followed by fractional distillation to isolate C9–C14 olefins. These olefins undergo hydroformylation using cobalt carbonyl catalysts to generate aldehydes, which are subsequently oxidized to carboxylic acids using Pinnick oxidation under mild aqueous‐phase conditions. Neutralization of the resulting carboxylic acids with sodium hydroxide produces plastic‐derived carboxylate surfactants (PDCs) in the form of sodium carboxylates. Subsequent purification steps ensure surfactant‐grade purity and enable accurate assessment of physicochemical properties. The resulting PDCs are evaluated for critical micelle concentration (CMC), foamability, surface tension reduction, and calcium ion tolerance, demonstrating competitive behavior with conventional anionic carboxylate surfactants. This route provides a sustainable alternative for surfactant production, reducing reliance on fossil‐derived feedstocks and valorizing plastic waste streams through chemical upcycling.

Biodegradable surfactants↗
DOE OSTI2025

Investigating Np(VI) Nitrate Speciation Control through Temperature and Optical Spectroscopy

Numerous areas of nuclear processing, such as radioisotope production, nuclear waste remediation, and separations, depend upon the speciation of f-elements in the solution state. However, fundamental knowledge of the actinides─particularly Np─lags behind most of the elements on the periodic table. Despite the importance of Np(VI) chemistry in separations and nuclear processing, its speciation in HNO 3 remains uncertain. This work addresses some of these gaps by investigating the effect of HNO 3 concentration and temperature on the spectra and speciation of the Np(VI) nitrate system. Six samples of Np in 1 to 10 M HNO 3 were prepared and treated with (NH 4 ) 2 [Ce(NO 3 ) 6 ] to stabilize the hexavalent oxidation state. The absorbance spectrum of the 10 M HNO 3 is drastically different from the spectra of the other samples; the 10 M spectrum indicates coordination of nitrate ligands to the Np(VI)O 2 2+ ion to form a complex with high symmetry. Additionally, absorbance spectra were recorded over the temperature range of 15 to 40 °C, and systematic increases and decreases in certain spectral features of the ultraviolet–visible (UV–vis)–near-infrared (NIR) spectra are present in the spectra. The difference in spectral features suggests that Np(VI) nitrate speciation depends on temperature. Dilution studies of this sample were monitored with UV–vis–NIR and Raman spectroscopies. Spectral data indicate the presence of multiple complexes with different symmetries, including a high-symmetry complex with an inversion center. As samples are diluted and aquo ligands replace nitrate ligands bound to the Np(VI) neptunyl cation, changes in spectroscopic signals indicate a decrease in the high-symmetry nitrate complex and an increase in the lower-symmetry aquo complex. Additionally, the Raman band associated with the Np(VI)O 2 2+ symmetric stretch broadens with dilution and is fitted with two peaks. These peaks are assigned to Np(VI) aquo and nitrato complexes, indicating that this vibrational mode is sensitive to the coordination environment of the Np(VI) neptunyl cation and that contributions from these two Np(VI) complexes can be distinguished. This unique experimental data could be used to advance computational models describing the electronic transitions of complex actinyl ions.

Absorption↗
DOE OSTI2025

Evaluation of Hanford 200 West Area Tank Farms (241-S/241-SX-/241-U tank farms) Physical Properties Data for Use in Development of West Area Tank Treatment (WATT) Processing

With the recent acceptance of West Area Tank Treatment disposition alternative for 200 West Area tanks at the Hanford Site by the State of Washington and the U.S. Department of Energy, a review was initiated to identify the physical properties data available in the literature for the Hanford 241-S, 241-SX, and 241-U tank farms. The literature reviewed indicated that there is a relatively small set of useful data on physical properties of 200 West Area tanks, and the data that do exist are biased around a narrow range of tank samples. Much of the testing between the 1990s and mid-2010s was intended to support either enhanced sludge washing or feed delivery to the Pretreatment Facility at the Hanford Waste Treatment and Immobilization Plant. As such, some physical properties of 200 West Area samples were measured under conditions that are no longer relevant. Because of the distinctly different nature of many past processes at the 200 West Area compared to the 200 East Area, insight from waste testing in the 200 East Area waste should be used with caution, as there may be significantly different qualities in the physical properties data between these two areas (both in situ and as measured in laboratory analyses). Based on this assessment, there is a need to collect additional physical property data to support planning for 200 West Area retrievals.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Catalytic monoterpenes conversion over Pd and zeolite to sustainable aviation fuel

Waste terpenes from wood drying are typically processed using a Regenerative Thermal Oxidizer (RTO) and converted to CO2 which is then released to the atmosphere. A novel alternative to this approach is to capture these terpenes using Fluidized Bed Concentrator (FBC) technology developed by CaptisAire which provides a useful waste carbon feedstock for subsequent upgrading. We have developed a catalytic approach where these waste terpenes (comprised of pinenes, limonene, and camphene), are converted to aromatic, and cycloalkane hydrocarbons suitable for use as a Sustainable Aviation Fuel (SAF) blendstock without the need for additional hydrogen. This provides a renewable source for aviation fuel aromatics and increases the potential blend content of renewably sourced alkanes from Hydroprocessed Esters and Fatty Acids (HEFA) and Alcohol to Jet (ATJ) processes. Terpenes were converted in a batch reactor at 260 °C and 120 psi N2 using a combination of Pd/C and H-BEA zeolite. Experimental results infer the role of the zeolite Brønsted acid to facilitate isomerization of pinenes and camphene to limonene, which then undergoes subsequent dehydro-aromatization to p-cymene using Pd/C. Hydrogen release from the dehydro-aromatization process, enables inert conversion of monoterpenes to cycloalkanes without additional hydrogen. Monoterpenes conversion to C10 aromatics (60%) and C10 cycloalkanes (40%) in an inert environment, provides a viable route for SAF blendstock sourced directly from captured waste terpenes. Transition to commercial off-the-shelf catalysts, facilitates scale-up of the terpene conversion process and improves commercial viability. We subsequently created hydrocarbon blends using HEFA or ATJ and converted terpenes, providing a 100% SAF blend with potential to replace traditional Jet-A.

Lawal, Ajibola [ORNL] (ORCID:0000000187266570)↗
DOE OSTI2024

Modeling nuclear waste disposal in crystalline rocks at the Forsmark and Olkiluoto repository sites – Evaluation of potential thermal–mechanical damage to repository excavations

We conduct coupled thermo-hydro-mechanical modeling of a KBS-3V repository design in crystalline rocks, using data and conditions from the Forsmark in Olkiluoto repository sites in Sweden and Finland. The study focuses on repository performance related to the impact of thermal and hydraulic evolution on the potential for thermal–mechanical damage to underground repository excavations. For the designs and conditions considered at the Forsmark and Olkiluoto repository sites, the simulations show a peak temperature well under the adopted performance target of a 100°C maximum temperature, whereas there is still a high potential for thermal–mechanical damage to the KBS-3V waste deposition holes. The thermal–mechanical damage is much more likely if rock permeability is so low that it delays saturation and swelling of bentonite-clay-based backfill beyond the time for the thermal–mechanical peak, which occurs 50 to 100 years after nuclear waste deposition. We also found that sidewalls of the KBS-3V emplacement tunnels are vulnerable to tensile fracturing due to the combined effect of thermal stressing and backfill swelling. The study highlights a strong interaction between bentonite-based backfill and host rock through capillary suction along with induced rock desaturation. A careful design and selection of the bentonite-clay-based backfill materials for KBS-3V tunnels and deposition holes can facilitate a timely saturation and backfill swelling that in turn can minimize thermal–mechanical damage.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

NREL's 1MW Water Electrolysis Stack Performance Validation to Pilot-Scale Renewable Natural Gas Production [Slides]

NREL has designed, built, and operates a 1MW water electrolyzer balance-of-plant to support industrial partners and the U.S. Department of Energy in developing next-generation PEM stacks to reduce the cost of hydrogen production. With that hydrogen, we are developing, innovating and de-risking a biomethanation process capable of megawatt-scale deployment that upgrades biogas waste streams to produce pipeline quality renewable natural gas (RNG). Biomethanation is a two-step process using a methanogenic microorganism to convert renewable hydrogen (H 2 ) and waste carbon dioxide (CO 2 ) to renewable methane (CH 4 ) - the primary component in natural gas. Using biogenic CO 2 from biogas sources like dairies, wastewater treatment plants, and landfills allows production of this drop-in direct replacement fuel. Research projects and future R&D topics are also discussed during the presentation.

08 HYDROGEN↗
DOE OSTI2024

Glass Formulation and Testing with RPP-WTP HLW Simulants (Final Report)

This report presents the results from HLW glass formulation work that was conducted at the Vitreous State Laboratory of The Catholic University of America during Part B1 of the RPP-WTP Project (formally known as TWRS-P) in support of the Privatization contractor, BNFL, Inc. Glass formulation development is required to provide data that are essential for design of the vitrification facility in the near term and for safe and reliable operation of that facility in the longer-term. These data also form the bases from which contractually and technically acceptable immobilized high-level waste (IHLW) products will be devised. Glass formulation therefore impacts many aspects of the vitrification facility design, overall process economics, and contractual compliance. As an integral part of the overall system design, development of glass formulations requires input from many sources including tank waste characterization, pretreatment process definition, flow sheet development, and processing schedules. Accordingly, the glass formulation effort must be responsive to new information as the facility design basis evolves.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Process intensification approach to enhancing heat and mass transfer: Radio frequency (RF) assisted drying of paper and board

Conventional multi-cylinder drying of paper and board typically relies on both conductive drying from steam-heated cylinders and convective drying, where heated air flows over the paper web surface. Conduction primarily contributes to heat transfer, while convection is the main driver of mass transfer. However, conventional drying systems are heavily dependent on steam, usually powered by fossil fuels, and are often energy-inefficient with high levels of waste. Additionally, these surface-driven processes result in a lower percentage of energy absorption compared to the energy supplied, leading to significant energy losses. To improve this long-standing process, an experimental system was developed to investigate a process intensification approach involving the integration of Radio Frequency (RF) heating, a volumetric electromagnetic technology, alongside traditional conduction and convection drying methods. This study also emphasizes the use of sensors to continuously monitor key parameters such as moisture content, supply system temperatures, sample temperatures, air flows, and drying rates in real-time. The effect of RF as an auxiliary energy source in localized environments at varying moisture levels was explored to optimize industrial drying systems, quantify potential improvements, and provide insights for future studies. Experimental results from trials combining RF with convection and with the base case alternating conduction-convection drying processes are presented. It is shown that RF is a viable process intensification approach for paper drying improving the drying rate and energy intensity at higher moisture contents. These findings offer valuable insights for process intensification and contribute to the process development, modeling, and simulation of advanced paper drying techniques.

42 ENGINEERING↗
DOE OSTI2025

Correction to “Greenhouse Gas and Air Pollutant Emissions from Composting”

Composting can divert organic waste from landfills, reduce landfill methane emissions, and recycle nutrients back to soils. However, the composting process is also a source of greenhouse gas and air pollutant emissions. Researchers, regulators, and policy decision-makers all rely on emissions estimates to develop local emissions inventories and weigh competing waste diversion options, yet reported emission factors are difficult to interpret and highly variable. This review explores the impacts of waste characteristics, pretreatment processes, and composting conditions on CO 2 , CH 4 , N 2 O, NH 3 , and VOC emissions by critically reviewing and analyzing 388 emission factors from 46 studies. The values reported to date suggest that CH 4 is the single largest contributor to 100-year global warming potential (GWP100) for yard waste composting, comprising approximately 80% of the total GWP 100 . For nitrogen-rich wastes including manure, mixed municipal organic waste, and wastewater treatment sludge, N 2 O is the largest contributor to GWP 100 , accounting for half to as much as 90% of the total GWP 100 . If waste is anaerobically digested prior to composting, N 2 O, NH 3 , and VOC emissions tend to decrease relative to composting the untreated waste. Effective pile management and aeration are key to minimizing CH 4 emissions. However, forced aeration can increase NH 3 emissions in some cases.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Accelerating Discovery to Deployment: Argonne's Materials Engineering Research Facility (MERF) and Its Role in Scaling Materials Technologies for Water and Resource Solutions

The U.S. Department of Energy (DOE) national laboratories represent a unique class of government‐owned, contractor‐operated research institutions dedicated to conducting research and development (R&D) related activities that address national priorities, supporting and advancing the DOE mission. They play a vital role in sustaining U.S. innovation capacity, stewarding the nation's technical base, and nurturing science and technologies. In this perspective, we highlight the processing science and scaleup capabilities of the Materials Engineering Research Facility (MERF) at DOE's Argonne National Laboratory to demonstrate how DOE National Laboratories bridge fundamental science and applied technology development to accelerate deployment. Case studies are presented on selective membranes for critical mineral recovery, sensors for per‐ and polyfluoroalkyl substances (PFAS) detection, surface functionalization via atomic layer deposition (ALD) and sequential infiltration synthesis (SIS), and lithium recovery from battery recycling waste streams using a novel electrodialysis process. These examples underscore MERF's role in translating innovative technologies into practical solutions for renewable water and critical resource recovery, which also leverage Argonne's analytical and computational capabilities. This perspective also outlines mechanisms for collaborating with the DOE national laboratories to strengthen partnerships across government, the national laboratories, academia, and industry.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Life Cycle Greenhouse Gas Emissions of Biogas Upgrading for Fuel Production

Waste-to-Renewable Natural Gas (RNG) offers a promising solution to alleviating waste management challenges by converting waste into renewable fuels. Here, this process can significantly reduce greenhouse gas (GHG) emissions, as demonstrated through a comprehensive life cycle analysis. Biogas upgrading is essential to enhance the methane concentration, though it could be energy-intensive and susceptible to methane slippage. Four commonly adopted biogas upgrading technologies, including pressure swing adsorption, membrane separation, chemical absorption, and water scrubbing, are considered. Our study evaluates the life cycle GHG emissions of RNG production from major sources of waste in the U.S. including wastewater sludge, food waste, landfill gas, dairy cow manure, and swine manure. Meta-analysis was conducted to assess methane slippage and energy consumption of biogas upgrading and associated GHG emissions, while accounting for potential avoided emissions from conventional waste management, which vary widely (ranging from −481.0 to 101.8 g CO 2 -eq/MJ). Under default upstream assumptions, representative carbon intensity of RNG varies from about −125 g of CO 2 -eq/MJ (dairy cow manure) to about 41 g of CO 2 -eq/MJ (wastewater sludge). We also explored RNG applications in producing hydrogen, ammonia, and compressed/liquefied forms. These findings highlight the potential of RNG and RNG-derived fuels to reduce GHG emissions and bolster the U.S. energy supply.

Biogas upgrades↗
DOE OSTI2025

Dual C–H functionalization of polyolefins for covalent adaptable network formation via cooperative electrolysis

The increasing demand for carbon fibre-reinforced polymer composites with polyolefin thermoset matrices will lead to the generation of large volumes of low molecular weight waste oligomers during the fibre recovery process. To address this challenge, we present a cooperative electrolytic dual C–H bond functionalization strategy for the one-step installation of two key functional groups essential for dynamic linkages of these deconstructed oligomers. Through direct competition studies, we reveal the predominance of tertiary allylic C–H activation along the complex, branched oligomer backbone. The resulting difunctionalized oligomers form covalently adaptable networks with exceptional circularity. By establishing a sustainable pathway for upcycling deconstructed oligomers from carbon fibre-reinforced polymer fibre recovery, this strategy introduces thermoset materials derived directly from waste. Here, it advances sustainable manufacturing practices, contributing to a net-zero waste synthetic ecosystem, and highlights the prospects of mediated electrolysis in macromolecular transformations.

Electrocatalysis↗
DOE OSTI2025

Influence of Process Parameter and Build Rate Variations on Defect Formation in Laser Powder Bed Fusion SS316L

Laser powder bed fusion (LPBF) is an additive manufacturing process that has gained interest for its material fabrication due to multiple advantages, such as the ability to print parts with small feature sizes, good mechanical properties, reduced material waste, etc. However, variations in the key process parameters in LPBF may result in the instantiation of porosity defects and variation in build rate. Particularly, volumetric energy density (VED) is a variable that encapsulates a number of those parameters and represents the amount of energy input from the laser source to the feedstock. VED has been traditionally used to inform the quality of the printed part but different values of VED are presented as optimal values for certain material systems. An optimal VED value can be maintained by changing the key process parameters so that various combinations yield a constant value. In this study, an optimal constant VED value is maintained while printing SS316L with variable key processing parameters. Porosity analysis is performed using optical microscopy, as well as X-ray computed tomography, to reveal the volume density and distribution of those pores. Two primary defect categories are identified, namely lack of fusion and porosity induced by balling defects. The findings indicate that, even at optimal VED, variations in process parameters can significantly influence defect type, underscoring the sensitivity of defect formation to the variation of these parameters. Furthermore, a minor change in the build rate, driven by adjustments in process parameters, was found to influence defect categories. These findings emphasize that fine tuning the process parameters and build rate is essential to minimize defects. Finally, fiducial marks have been identified as a source of unintentional porosity defects. These results enable the refinement of process parameters, ultimately optimizing LPBF to achieve enhanced material density and expedite the printing.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Development of an ERT‐Based Framework for Bentonite Buffers Monitoring From Laboratory Tests: 1. Characterizing Thermal–Hydrological–Mechanical Processes

Abstract Bentonite clay is widely used in engineered barrier systems for the permanent disposal of high‐level radioactive waste due to its low permeability, high swelling capacity, and thermal stability. However, the complex thermal‐hydrological‐mechanical (THM) processes induced by heating from decaying radioactive waste and hydration from surrounding rock can lead to heterogeneous changes that are difficult to measure and predict. This study develops an Electrical Resistivity Tomography (ERT)‐based framework for monitoring THM processes, progressing from sample‐scale to bench‐scale tests, to inform field‐scale applications. Sample‐scale tests analyzed small bentonite samples under controlled variations in water content, temperature, and porosity to establish fundamental resistivity relationships. Bench‐scale tests involved larger bentonite columns subjected to heating (up to 200°C) and hydration under controlled pressure, simulating repository conditions. ERT measurements, complemented by X‐ray CT imaging, temperature monitoring, and tracing sensors, revealed coupled THM processes, such as hydration‐induced compression, swelling, and thermal gradients, leading to complex resistivity patterns. The results demonstrate the potential of ERT for capturing THM‐induced resistivity changes, though challenges remain in upscaling and quantitative analysis. This study evaluates laboratory test capabilities and proposes future improvements for understanding THM‐induced resistivity responses. A conceptual framework for ERT implementation in field‐scale monitoring is presented, synthesizing findings from both scales and exploring how ERT data can inform long‐term modeling and reduce prediction uncertainties. Overall, this ERT‐based framework offers a robust method for monitoring bentonite buffers, aiding in early issue detection and supporting the safe long‐term disposal of radioactive waste in geological repositories, while highlighting the need for future development. Plain Language Summary Bentonite clay is crucial in engineered barrier systems (EBS) for containing high‐level radioactive waste due to its ability to absorb water, swell, seal and remain stable under high temperatures. When bentonite absorbs water and heats up from radioactive decay, it experiences complex changes in its physical and mechanical properties. Understanding these changes is important for ensuring the long‐term safety and effectiveness of EBS. This study used Electrical Resistivity Tomography (ERT), a non‐invasive method that measures electrical conductivity to monitor these changes during laboratory experiments. The ERT data revealed significant variations in resistivity corresponding to changes in water content, temperature, and density, providing detailed spatial and temporal insights into the behavior of bentonite. These findings enhance our ability to predict the long‐term performance of bentonite barriers, ensuring the safe containment of radioactive waste. By improving our understanding of bentonite's behavior, this research supports the development of more reliable and effective barrier systems for radioactive waste disposal, protecting the environment and public health. Key Points ERT monitoring was employed to capture resistivity changes in bentonite during controlled heating and hydration experiments, providing insights into THM processes ERT data reveal significant resistivity changes correlated with water content, temperature, and mechanical effects, enhancing the understanding of THM dynamics in bentonite This study explores the potential of the framework for application in field‐scale EBS monitoring, emphasizing the need for integrating additional geophysical methods for comprehensive subsurface imaging

Chen, Hang↗
DOE OSTI2024

Engineering-Scale Testing of the Biphasic Solvent Based CO 2 Absorption Capture Technology at a Covanta Waste-to-Energy Facility

The original goals of this project were to advance the development and demonstration of the Biphasic CO 2 Absorption Process (BiCAP) technology for CO 2 capture from waste-to-energy (WTE) generation at a 2.5 tonne per day (TPD) engineering scale. This project has primarily focused on the basic design of the 2.5 TPD pilot system within the inside battery limits pertaining to CO 2 capture. The project also conducted a preliminary techno-economic analysis (TEA) for BiCAP at a scale of 100,000 tonne per year (TPY) of CO 2 capture and a preliminary life cycle analysis (LCA) with a primary focus on the environmental impacts related to global warming potential.

09 BIOMASS FUELS↗