Search NASA⌕ Search

SEARCH · Search NASA

Results for “angle”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Dynamic flow angle measurements at the diffuser exit of a Mach 2.5 mixed compression inlet

An exploratory investigation was made to determine the magnitude of the dynamic flow angle at a single point in the diffuser exit of a Mach 2.50 inlet. Results indicate that the maximum flow angle variation was + or - 3 degrees except when vortex generators were installed in the subsonic diffuser. The amplitude of these flow angle fluctuations was directly related to the amplitude of the total pressure fluctuations at the probe survey point. Flow angle fluctuations as high as + or - 11 degrees were recorded when vortex generators were installed near the probe survey point.

Prati, W. M.↗
NASA NTRS1972

The effect of injection angle on the interaction between sonic secondary jets and a supersonic free stream

An experimental investigation, as part of a research program on the development of technology for the design of supersonic combustion ramjets, has been conducted to determine the effect of injection angle on the jet penetration, mixing rate, and airstream total-pressure recovery downstream of five laterally spaced sonic hydrogen jets flush mounted on a flat plate. Results of this investigation indicated that at lower injection angles less free-stream momentum loss was required to turn and accelerate the injected gas downstream and, thereby, less flow disturbance and total-pressure loss were produced. In addition, lower injection angles resulted in improved fuel distribution and faster mixing of the injected gas with the free stream. A correlating parameter, developed from considerations of the effective-momentum-flux differences between the injected gas and the free-stream air, predicted greater penetration and faster mixing for the lower injection angles.

Mcclinton, C. R.↗
NASA NTRS1972

Space shuttle: Aerodynamic characteristics of cone-cylinder-flare-fin configurations at Mach numbers of 1.96, 2.74, and 4.96 and angles of attack from 50 to 90 degrees

A 0.00227-scale parametric model of an LMSC/MSFC water recoverable booster was tested in the MSFC 14 x 14-inch trisonic wind tunnel. The purpose of the test was to obtain high angle of attack force and static stability data which could be used by MSFC in preliminary design and aerodynamic trade studies. These data were obtained using six-component internal strain gauge balances. One hundred forty-four different geometrical combinations were possible as all model parts were interchangeable (three nose cones, three cylinder lengths, four flare sections and three sets of fins, plus a no-fin case in combination with the other components). However, due to tunnel occupancy limitations, only the most representative combinations were tested. All configurations investigated were tested at Mach 1.96, 2.74 and 4.96 with data obtained at angles of attack from 50 degrees to 90 degrees and at angles of sideslip from -10 degrees to +10 degrees (at an angle of attack of 60 degrees).

Bradley, D.↗
NASA NTRS1973

Prediction of static aerodynamic characteristics for space-shuttle-like and other bodies at angles of attack from 0 deg to 180 deg

An engineering-type procedure is presented for computing normal-force, axial-force, and pitching-moment coefficients for bodies at angles of attack from 0 deg to 180 deg. The procedure is ideally suited for estimating the aerodynamic characteristics of space shuttle booster-like bodies because of the wide range of angles of attack, Mach numbers, and Reynolds numbers to be encountered. The analytical formulas, plots, and references given are also applicable for shuttle orbiter, missile, and aircraft-like bodies of both circular and noncircular cross section. The method for computing normal-force and pitching-moment coefficients is based upon the original proposal of Allen that the crossflow or lift distribution over a body can be expressed as the sum of slender-body potential term and an empirical viscous crossflow term. Although experimental data from which to verify the procedure at very high angles of attack are extremely limited, the comparisons made thus far of computed with experimental results are good. In this report the procedure has been shown to be capable of predicting reasonably well the experimental variation of C sub N, C sub A, C sub m, and x sub ac/l with angle of attack for nine bodies of revolution at a free-stream Mach number of 2.86.

Jorgensen, L. H.↗
NASA NTRS1973

Experimental investigation of orthotropic panel flutter at arbitrary yaw angles, and comparison with theory

Flutter characteristics for yaw angles between 15 deg and 90 deg were determined experimentally for two types of corrugation-stiffened panels: those with weak twisting stiffness and those with strong twisting stiffness. By mounting the panels on a remotely controlled turntable, good definition of the flutter boundaries was obtained by rotating the panels into and out of flutter. Flutter tests were conducted at M = 2 and M = 1.6. Before testing, vibration tests and analyses were also performed. The experimental flutter data is compared with flutter theory for orthotropic panels utilizing quasi-steady aerodynamics. Five different corrugated panels were tested consisting of one single skin panel having a length-to-width ratio of 5 on clamped supports and four different square double skin panels on discrete flexible supports. The investigation indicated that flutter speed for corrugated panels is highly dependent on yaw angle. Reasonable flutter correlation between analysis and test was obtained for moderate yaw angles, but extreme sensitivity to structural parameters made the correlation at large yaw angles uncertain.

Shyprykevich, P.↗
NASA NTRS1974

Flutter of elastically supported orthotropic panels including the effects of flow angle

A theoretical panel flutter analysis and computer program was developed which is capable of analyzing an orthotropic panel with in-plane loads, at various angles of cross flow and various edge-support conditions. The resulting modal analysis uses linear piston-theory aerodynamics and includes both aerodynamic and structural damping. Calculations made for typical panels with no in-plane forces show that large reductions in dynamic presure for flutter are possible with only small changes in flow angle. The reduction in dynamic pressure with flow angle is greater for elastically supported panels than for simply supported panels. Aerodynamic damping has a significant stabilizing effect at all flow angles except zero, whereas structural damping has negligible effect.

Sawyer, J. W.↗
NASA NTRS1974

Mirroring within the Fokker-Planck formulation of cosmic ray pitch angle scattering in homogeneous magnetic turbulence

The Fokker-Planck coefficient for pitch angle scattering, appropriate for cosmic rays in homogeneous, stationary, magnetic turbulence, is computed from first principles. No assumptions are made concerning any special statistical symmetries the random field may have. This result can be used to compute the parallel diffusion coefficient for high energy cosmic rays moving in strong turbulence, or low energy cosmic rays moving in weak turbulence. Becuase of the generality of the magnetic turbulence which is allowed in this calculation, special interplanetary magnetic field features such as discontinuities, or particular wave modes, can be included rigorously. The reduction of this results to previously available expressions for the pitch angle scattering coefficient in random field models with special symmetries is discussed. The general existance of a Dirac delta function in the pitch angle scattering coefficient is demonstrated. It is proved that this delta function is the Fokker-Planck prediction for pitch angle scattering due to mirroring in the magnetic field.

Goldstein, M. L.↗
NASA NTRS1974

Evaluation of importance of lateral acceleration derivatives in extraction of lateral-directional derivatives at high angles of attack

A theoretical investigation was conducted to determine the importance of the lateral acceleration (beta) derivatives in the extraction of lateral-directional stability derivatives for swept wing airplanes at high angles of attack. Representative values of lateral acceleration derivatives in yaw and roll (Cn beta and Cl beta) were used in a computer program to generate representative flight motions at several angles of attack and altitudes. The computer-generated motions were then subjected to a parameter identification process based on a modified Newton-Raphson method. Two identification techniques were evaluated, one which included the beta derivatives and one which neglected them. The results of the study indicate that omission of the beta derivatives from mathematical models used in the derivative-extraction techniques can produce erroneous values for the lateral-directional stability derivatives particularly at high angles of attack, where the beta derivatives are large. The largest errors occur in the dynamic derivatives, but large errors may also occur in the static derivatives for cases in which the beta derivatives have large effects on the flight motions of the airplane. In addition, the resulting identified mathematical models provide poor motion prediction as well as erroneous predictions of dynamic modal characteristics. These results strongly indicate that the effects of beta derivatives should be considered in any attempt to extract lateral-directional aerodynamic parameters at high angles of attack.

Nguyen, L. T.↗
NASA NTRS1974

Viewing-angle effects in radar images

A quantitative determination of the effect of viewing angle on the detectability of topographic linears in radar imagery is presented. Variations of azimuth and aspect angles of an imaging radar antenna relative to a topographic linear were simulated using low-angle illumination of controlled linear features on polystyrene sheets. The several model surfaces represented idealized versions of surface types that may be expected in areas of geologic interest. Fourier transform spectra of the radar image simulations were obtained using a coherent-optics system. These spectra were found to correlate with a detectability factor obtained directly from the radar image simulations. Fourier transform spectra of a linear feature observed from multiple viewing angles by a K-band imaging radar were also obtained and a detectability factor was estimated which agreed closely with theoretical predictions.

Eppes, T. A.↗
NASA NTRS1974

The Fokker-Planck coefficient for pitch-angle scattering of cosmic rays

For the case of homogeneous, isotropic magnetic field fluctuations, it is shown that most theories which are based on the quasi-linear and adiabatic approximations yield the same integral for the Fokker-Planck coefficient for the pitch-angle scattering of cosmic rays. For example, despite apparent differences, the theories due to Jokipii and to Klimas and Sandri yield the same integral. It is also shown, however, that this integral in most cases has been evaluated incorrectly in the past. For small pitch angles, the errors in previous evaluations are fortuitously of minor importance. For large pitch angles, however, these errors become more significant; and for pitch angles of 90 deg, the actual Fokker-Planck coefficient contains a delta function which has been overlooked in the past. The implications of these corrections on the possibility of relating cosmic-ray diffusion coefficients to observed properties of the interplanetary magnetic field are discussed.

Fisk, L. A.↗
NASA NTRS1974

Onset of aerodynamic side forces at zero sideslip on symmetric forebodies at high angles of attack

Selected results are presented from extensive wind-tunnel tests that include variations in axial and cross-sectional shape, fineness ratio, bluntness, strakes, and boundary-layer trips over a wide range of conditions (angles of attack to 90 deg, angles of sideslip to 30 deg, Reynolds numbers from subcritical to supercritical, and Mach numbers from 0.1 to 0.7). Pointed forebodies at zero sideslip can experience side forces as large as maximum normal forces. The angle of attack at the onset of side force can be correlated with nose angle and afterbody length. Furthermore, these side forces can be reduced or eliminated by bluntness or nose strakes.

Keener, E. R.↗
NASA NTRS1974

Effects of leading edge sweep angle and design lift coefficient on performance of a modified arrow wing at a design Mach number of 2.6

Wing models were tested in the high-speed section of the Langley Unitary Plan wind tunnel to study the effects of the leading-edge sweep angle and the design lift coefficient on aerodynamic performance and efficiency. The models had leading-edge sweep angles of 69.44 deg, 72.65 deg, and 75.96 deg which correspond to values of the design Mach-number-sweep-angle parameter (beta cotangent A) sub DES of 0.6, 0.75, and 0.9, respectively. For each sweep angle, camber surfaces having design lift coefficients of 0,0.08, and 0.12 at a design Mach number of 2.6 were generated. The wind-tunnel tests were conducted at Mach numbers of 2.3, 2.6, and 2.96 with a stagnation temperature of 338.7 K (150 F) and a Reynolds number per meter of 9.843 times 10 to the 6th power. The results of the tests showed that only a moderate sweeping of the wing leading edge aft of the Mach line along with a small-to-moderate amount of camber and twist was needed to significantly improve the zero-lift (flat camber surface) wing performance and efficiency.

Mack, R. J.↗
NASA NTRS1975

Comparison of experimental and theoretical boundary-layer separation for inlets at incidence angle at low-speed conditions

Comparisons between experimental and theoretical Mach number distributions and separation locations are presented for the internal surfaces of four different subsonic inlet geometries with exit diameters of 13.97 centimeters. The free stream Mach number was held constant at 0.127, the one-dimensional throat Mach number ranged from 0.49 to 0.71, and the incidence angle ranged from 0 deg to 50 deg. Generally good agreement was found between the theoretical and experimental surface Mach number distributions as long as no flow separation existed. At high incidence angles, where separation was obvious in the experimental data, the theory predicted separation on the lip. At lower incidence angles, the theoretical results indicated diffuser separation which was not obvious from the experimental surface Mach number distributions. As incidence angle was varied from 0 deg to 50 deg, the predicted separation location shifted from the diffuser region to the inlet highlight. Relatively small total pressure losses were obtained when the predicted separation location was greater than 0.6 of the distance between the highlight and the diffuser exit.

Felderman, E. J.↗
NASA NTRS1975

Experimental aerodynamics characteristics for bodies of elliptic cross section at angles of attack from 0 deg to 58 deg and Mach numbers from 0.6 to 2.0

An experimental investigation was conducted to measure the static aerodynamic characteristics for two bodies of elliptic cross section and for their equivalent body of revolution. The equivalent body of revolution had the same length and axial distribution of cross-sectional area as the elliptic bodies. It consisted of a tangent ogive nose of fineness ratio 3 followed by a cylinder with a fineness ratio of 7. All bodies were tested at Mach numbers of 0.6, 0.9, 1.2, 1.5, and 2.0 at angles of attack from 0 deg to 58 deg. The data demonstrate that the aerodynamic characteristics can be significantly altered by changing the body cross section from circular to elliptic and by rolling the body from 0 deg to 90 deg. For example, the first elliptic body (with a constant cross-sectional axis ratio of 2) developed at zero roll about twice the normal force developed by the equivalent body of revolution. At some angles of attack greater than about 25 deg, side forces and yawing moments were measured in spite of the fact that the bodies were tested at zero angle of sideslip. The side-force and yawing-moment coefficients decreased with an increase in Mach number and essentially disappeared for all the bodies at Mach numbers greater than 1.2. From the standpoint of reducing undesirable side forces at high angles of attack, it is best to have the flattest side of the nose of the elliptic bodies pitching against the stream crossflow. The effect of Reynolds number was also the least significant for both elliptic bodies when the flattest side of the nose was pitched against the stream crossflow.

Jorgensen, L. H.↗
NASA NTRS1975

An investigation of the solar zenith angle variation of D-region ionization

Model calculations are carried out with a view to interpreting the solar zenith angle variation of D-region ionization. A model is developed for the neutral chemistry including the transport terms relating to molecular and eddy diffusion. The diurnal behavior is described of the minor neutral constituents formed in an oxygen-hydrogen-nitrogen atmosphere, in the height interval between 30 and 120 km. Computations carried out for two cases of the eddy diffusion coefficients models indicate that the constituents which are important for the D-region positive-ion chemistry do not show a significant variation with zenith angle for values up to 75 deg over the D-region heights. In the ion chemistry model, ion-pair production rates are calculated for solar X-rays between 1 A and 100 A, EUV radiations from 100 A up to the Lyman-alpha line, precipitating electrons, and galactic cosmic rays. The solar zenith angle variation of the positive-ion composition, negative-ion composition, and the electron densities are described up to 75 deg zenith angle, in the height interval between 60 and 100 km.

Ratnasiri, P. A. J.↗
NASA NTRS1975

Normal- and oblique-shock flow parameters in equilibrium air including attached-shock solutions for surfaces at angles of attack, sweep, and dihedral

Normal- and oblique-shock flow parameters for air in thermochemical equilibrium are tabulated as a function of shock angle for altitudes ranging from 15.24 km to 91.44 km in increments of 7.62 km at selected hypersonic speeds. Post-shock parameters tabulated include flow-deflection angle, velocity, Mach number, compressibility factor, isentropic exponent, viscosity, Reynolds number, entropy difference, and static pressure, temperature, density, and enthalpy ratios across the shock. A procedure is presented for obtaining oblique-shock flow properties in equilibrium air on surfaces at various angles of attack, sweep, and dihedral by use of the two-dimensional tabulations. Plots of the flow parameters against flow-deflection angle are presented at altitudes of 30.48, 60.96, and 91.44 km for various stream velocities.

Hunt, J. L.↗
NASA NTRS1976

Incidence angle bounds for lip flow separation of three 13.97-centimeter-diameter inlets

Low speed wind tunnel tests were conducted to establish a procedure for determining inlet-lip flow separation and to make preliminary examination of the incidence angle bounds for lip flow separation on inlets intended for the nacelles of STOL (short takeoff and landing) aircraft. Three inlets were tested. Two of the inlets had short centerbodies with lower lip area contraction ratios of 1.30 and 1.44. The third inlet had a cylindrical centerbody extended forward into the inlet throat with a lower lip area contraction ratio of 1.44. The inlets were sized to fit a 13.97 centimeter-diameter fan. For inlet throat Mach numbers less than about 0.43, the lip flow separation angle was increased by either increasing the ratio of throat velocity to freestream velocity (Vt/Vo) or by increasing the lower lip area contraction ratio. For throat Mach numbers greater than a certain value (ranging from 0.43 to 0.52), increasing throat Mach number in some cases resulted in a decrease in the lip flow separation angle. Extending a cylindrical centerbody into the inlet throat increased the flow separation angle for nearly all values of Vt/Vo.

Luidens, R. W.↗
NASA NTRS1976

Inlets for high angles of attack

Different inlet designs for high angle of attack STOL and VTOL applications were tested in a subsonic wind tunnel. Three removable entry lips having contraction ratios of 1.30, 1.34 and 1.38 were tested with a single diffuser. The internal contour of each entry lip was an ellipse with a major to minor axis of 2.0. Each lip and diffuser assembly was tested to determine its tolerance to angle of attack, first with a conventional centerbody and then with an extended centerbody. Results indicate that a large improvement in separation angle (determined as a function of lip contraction ratio and inlet flow) was obtained for the extended centerbody for all contraction ratios. Improved inlet tolerance to angle of attack was obtained by reducing the adverse pressure gradient downstream of the throat.

Miller, B. A.↗