Search NASA⌕ Search

SEARCH · Search NASA

Results for “band engineering”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS2008

Time Delay Analysis of Turbofan Engine Direct and Indirect Combustion Noise Sources

The core noise components of a dual spool turbofan engine were separated by the use of a coherence function. A source location technique based on adjusting the time delay between the combustor pressure sensor signal and the far-field microphone signal to maximize the coherence and remove as much variation of the phase angle with frequency as possible was used. The discovery was made that for the 130o microphone a 90.027 ms time shift worked best for the frequency band from 0 to 200 Hz while a 86.975 ms time shift worked best for the frequency band from 200 to 400 Hz. Hence, the 0 to 200 Hz band signal took more time than the 200 to 400 Hz band signal to travel the same distance. This suggests the 0 to 200 Hz coherent cross spectral density band is partly due to indirect combustion noise attributed to entropy fluctuations, which travel at the flow velocity, interacting with the turbine. The signal in the 200 to 400 Hz frequency band is attributed mostly to direct combustion noise. Results are presented herein for engine power settings of 48, 54, and 60 percent of the maximum power setting

Miles, Jeffrey Hilton↗
DOE OSTI2022

Crystallographic ordering of Al and Sn in α-Ti

Increasing attention is being paid to α (2) Ti 3 (Al,Sn) precipitation from the α phase of titanium alloys owing to its effect on slip band formation, localisation and the implications for fatigue performance in jet engine titanium. However, the early stages of α 2 precipitation have historically been difficult to observe by electron microscopy, neutron diffraction or atom probe analysis. Here, small angle X-ray scattering is used to reexamine the phase boundary in binary Ti-Al and Ti-Sn alloys with around 500 ppmw O. It is found that the phase boundaries in the literature are approximately correct, at 6.2 wt.% Al and 16.9 wt.% Sn, and that this favours the use of Al as a solid solution strengthener over Sn for ambient temperature applications. However, once O content and phase partitioning in α + β alloys are taken into account, this implies that Al eq limits for future alloy design of critical rotating parts should be lowered substantially.

36 MATERIALS SCIENCE↗
NASA NTRS1976

Interim prediction method for turbine noise

A turbine noise prediction method for interim use in the NASA Aircraft Noise Prediction Program is selected. The method predicts the level, directivity, and one-third octave band spectra of far field turbine noise as a function of engine parameters. The selection results from a review of turbine noise data and prediction methods available in the open literature. It is concluded that the state-of-the-art turbine noise prediction capability is primitive and that the selected method represents only a temporary interim approach. Recommendations are made on research requirements.

Krejsa, E. A.↗
NASA NTRS2001

An Architecture Trade Study for Passive 10-km Soil Moisture Measurements from Low-Earth Orbit

In 1999 NASA HQ, as a result of an internal NASA study on potential Earth Science Enterprise Post-2002 Missions, directed the hydrology community to focus on achieving a 10-km spatial resolution global soil moisture mission. This type of resolution represents a significant technological challenge for an L-band radiometer in sun-synchronous low-earth orbit. An engineering trade study has been completed to determine alternative system configurations that could achieve the science requirements and to identify the most appropriate technology investments and development path for NASA to pursue in order to bring about such a mission. The results of the study are presented here together with a short discussion of future efforts.

Pellerano, Fernando↗
DOE OSTI2025

Mechanically and electrically tunable Rashba-Edelstein effect in ferroelectric semiconductors, CsGe⁢𝑋 3 (𝑋 = I, Br, Cl)

The ability of materials to convert charge current into spin current is fundamental to many spintronics applications. One means of realizing this conversion is via Rashba-Edelstein effect (REE). Using density functional theory simulations, we predict that REE can be induced in the recently discovered family of semiconducting ferroelectrics, CsGe⁢𝑋 3 (𝑋 = I, Br, Cl). The effect is quantified through Rashba-Edelstein coefficients, 𝜒 𝑥⁢𝑦 =−𝜒 𝑦⁢𝑥 , which are nonzero in valence and conduction bands. The largest values, obtained for CsGeI 3 , are 3.45 × 10 10 $\frac{ℏ}{Λ cm}$ and 0.97 × 10 10 $\frac{ℏ}{Λ cm}$ in the conduction and valence bands, respectively. The values are comparable to, and sometimes exceed, those of other inorganic materials, although the maximal values occur away from the band edges. The coefficients' sign couples to the direction of spontaneous polarization, offering opportunities for nonvolatile spin current manipulation via external electric field. Furthermore, these coefficients are highly tunable through strain engineering owing to strain-induced variations in spin textures and energy isosurfaces. Specifically, 𝜒 in the valence band of CsGeI 3 is enhanced to 3.61 × 10 10 $\frac{ℏ}{Λ cm}$ under 5% biaxial strain. Given this potential, we synthesized CsGeI 3 to validate our simulation structure and found excellent agreement between experiment and simulation, thereby allowing extrapolation of our findings to practically significant temperatures. Furthermore, our study identifies promising materials for nonvolatile, multifunctional spintronic applications.

Electronic structure↗
DOE OSTI2025

Low-phase-noise surface-acoustic-wave oscillator using an edge mode of a phononic band gap

Low-phase-noise microwave-frequency integrated oscillators provide compact solutions for various applications in signal processing, communications, and sensing. Surface acoustic waves (SAWs), featuring orders-of-magnitude shorter wavelength than electromagnetic waves at the same frequency, enable integrated microwave-frequency systems with much smaller footprint on chip. SAW devices also allow higher-quality (Q) factors than electronic components at room temperature. Here, we demonstrate a low-phase-noise gigahertz-frequency SAW oscillator on 128°Y-cut lithium niobate, where the SAW resonator occupies a footprint of 0.05 mm 2 . Leveraging phononic crystal band-gap-edge modes to balance between Q factors and insertion losses, our 1-GHz SAW oscillator features a low phase noise of -132.5 dBc/Hz at a 10-kHz offset frequency and an overlapping Hadamard deviation of 6.5 × 10 -10 at an analysis time of 64 ms. The SAW resonator-based oscillator holds high potential in developing low-noise sensors and acousto-optic integrated circuits.

42 ENGINEERING↗
DOE OSTI2026

Curvilinear Magnonic Crystal Based on 3D Hierarchical Nanotemplates

Curvilinear magnetic nanostructures enable control of magnetization dynamics through geometry-induced anisotropy and chiral interactions, as well as magnetic field modulation. In this work, we report a curvilinear magnonic crystal based on large-area square arrays of truncated nanospikes fabricated by conformal coating of 3D hierarchical templates with permalloy thin films. Brillouin light scattering spectroscopy reveals an anisotropic band structure with multiple dispersive and folded Bloch-type dispersive spin-wave modes as well as nondispersive modes exhibiting direction-dependent frequency shifts and intensity asymmetries along lattice principal axes. Finite element micromagnetic simulations indicate that curvature-induced variations of the demagnetizing field govern the magnonic response, enabling the identification of modes propagating in nanochannels and others localized on nanospike apexes or along the ridges connecting adjacent nanospikes. The combination of geometric curvature and optical probing asymmetry produces directional dependence of magnonic bands, establishing 3D hierarchical templates as a versatile platform for curvature-engineered magnonics.

3D hierarchical templates↗
NASA NTRS2000

Shuttle Radar Topography Mission (SRTM) Flight System Design and Operations Overview

This paper provides an overview of the Shuttle Radar Topography Mission (SRTM), with emphasis on flight system implementation and mission operations from systems engineering perspective. Successfully flown in February, 2000, the SRTM's primary payload consists of several subsystems to form the first spaceborne dual-frequency (C-band and X-band) fixed baseline interferometric synthetic aperture radar (InSAR) system, with the mission objective to acquire data sets over 80% of Earth's landmass for height reconstruction. The paper provides system architecture, unique design features, engineering budgets, design verification, in-flight checkout and data acquisition of the SRTM payload, in particular for the C-band system. Mission operation and post-mission data processing activities are also presented. The complexity of the SRTM as a system, the ambitious mission objective, the demanding requirements and the high interdependency between multi-disciplined subsystems posed many challenges. The engineering experience and the insight thus gained have important implications for future spaceborne interferometric SAR mission design and implementation.

Shen, Yuhsyen↗
NASA NTRS1949

Altitude-Test-Chamber Investigation of Mcdonnell Afterburner on J34 Engine

An altitude-test-chamber investigation was conducted to determine the operational and performance characteristics of a McDonnell afterburner with a fixed-area exhaust nozzle on a J34 engine. At rated engine speed, the altitude limit, as determined by combustion blow-out, occurred as a band of unstable operation of about 6000-foot altitude in width with minimum altitude limits from 31,000 feet at a simulated flight Mach number of 0.40 to about 45,500 feet at a simulated flight Mach number of 1.00. Considerable difficulty was experienced in attempting to establish or maintain balanced-cycle engine operation at altitudes above 36,000 feet. The fuel-air ratio for balanced-cycle operation and lean blowout of the afterburner, the augmented-thrust ratio, the total specific fuel consumption, and the afterburner combustion efficiency for balanced-cycle operation are summarized in a table. Satisfactory afterburner ignition was obtained over a range of flight Mach Numbers from 0.32 to 0.60 at altitudes from 10,000 to 30,000 and engine speeds from 10,000 to 12,500 rpm.

Reller, John O.↗
NASA NTRS2012

NASA Tech Briefs, November 2012

The topics include: Visual System for Browsing, Analysis, and Retrieval of Data (ViSBARD); Time-Domain Terahertz Computed Axial Tomography NDE System; Adaptive Sampling of Time Series During Remote Exploration; A Tracking Sun Photometer Without Moving Parts; Surface Temperature Data Analysis; Modular, Autonomous Command and Data Handling Software with Built-In Simulation and Test; In-Situ Wire Damage Detection System; Amplifier Module for 260-GHz Band Using Quartz Waveguide Transitions; Wideband Agile Digital Microwave Radiometer; Buckyball Nucleation of HiPco Tubes; FACT, Mega-ROSA, SOLAROSA; An Integrated, Layered-Spinel Composite Cathode for Energy Storage Applications; Engineered Multifunctional Surfaces for Fluid Handling; Polyolefin-Based Aerogels; Adjusting Permittivity by Blending Varying Ratios of SWNTs; Gravity-Assist Mechanical Simulator for Outreach; Concept for Hydrogen-Impregnated Nanofiber/Photovoltaic Cargo Stowage System; DROP: Durable Reconnaissance and Observation Platform; Developing Physiologic Models for Emergency Medical Procedures Under Microgravity; Spectroscopic Chemical Analysis Methods and Apparatus; Low Average Sidelobe Slot Array Antennas for Radiometer Applications; Motion-Corrected 3D Sonic Anemometer for Tethersondes and Other Moving Platforms; Water Treatment Systems for Long Spaceflights; Microchip Non-Aqueous Capillary Electrophoresis (MicronNACE) Method to Analyze Long-Chain Primary Amines; Low-Cost Phased Array Antenna for Sounding Rockets, Missiles, and Expendable Launch Vehicles; Mars Science Laboratory Engineering Cameras; Seismic Imager Space Telescope; Estimating Sea Surface Salinity and Wind Using Combined Passive and Active L-Band Microwave Observations; A Posteriori Study of a DNS Database Describing Super critical Binary-Species Mixing; Scalable SCPPM Decoder; QuakeSim 2.0; HURON (HUman and Robotic Optimization Network) Multi-Agent Temporal Activity Planner/Scheduler; MPST Software: MoonKommand

Source record↗
DOE OSTI2025

Anisotropic strain relaxation-induced directional ultrafast carrier dynamics in RuO 2 films

Ultrafast light-matter interactions inspire potential functionalities in picosecond optoelectronic applications. However, achieving directional carrier dynamics in metals remains challenging due to strong carrier scattering within a multiband environment, typically expected for isotropic carrier relaxation. In this study, we demonstrate epitaxial RuO 2 /TiO 2 (110) heterostructures grown by hybrid molecular beam epitaxy to engineer polarization selectivity of ultrafast light-matter interactions via anisotropic strain engineering. Combining spectroscopic ellipsometry, x-ray absorption spectroscopy, and optical pump-probe spectroscopy, we revealed the strong anisotropic transient optoelectronic response at an excitation energy of 1.58 eV in strain-engineered RuO 2 /TiO 2 (110) heterostructures along both in-plane [001] and [1$\bar1$0] crystallographic directions. Theoretical analysis identifies strain-induced modifications in band nesting as the underlying mechanism for enhanced anisotropic carrier relaxation observed at this excitation energy. These findings establish epitaxial strain engineering as a powerful tool for tuning anisotropic optoelectronic responses with near-infrared excitations in metallic systems, paving the way for next-generation polarization-sensitive ultrafast optoelectronic devices.

Science & Technology - Other Topics↗
DOE OSTI2023

Constructing uniform oxygen defect engineering on primary particle level for high-stability lithium-rich cathode materials

Lithium-rich layered cathode materials are considered to be research focus of cathode candidates for next generation lithium-ion batteries due to their high specific capacity and low cost. However, lattice deoxidation associated with elemental migration and internal local shrinkage usually results in deteriorated cyclic performance and notorious voltage attenuation, severely limiting its application. In this paper, we have successfully injected uniform oxygen defects into surface region of Li 1.2 Ni 0.13 Co 0.13 Mn 0.54 O 2 primary particles under the high-pressure and weak carbonate environment. Various experimental investigations indicate that the injected robust oxygen defects can not only mitigate detrimental interfacial reactions but also suppress unfavorable lattice variation and particle breakage. More importantly, theoretical calculations unravel the critical roles of oxygen defects in regulating energy band structure for strengthened anionic reversibility. Owing to stabilization effects of unique oxygen defect engineering, the modified Li 1.2 Ni 0.13 Co 0.13 Mn 0.54 O 2 cathode has harvested dramatically enhanced electrochemical performance including a high initial coulombic efficiency of 96.6%, an outstanding capacity retention of 91.96% (1C, 200 cycles) and suppressed voltage decay of only 1.62 mV per cycle. Therefore, this facile and effective defect engineering strategy could establish new guidance for promoting practical application of Li-rich Mn-based cathode material.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Self-equilibrated backstresses induce compensation between hardening and softening: Micromechanical and microstructural features

For crystal plasticity formulation neglecting the strain gradients at the dislocation scale, backstresses are necessary to satisfy the mesoscopic stress equilibrium and strain compatibility requirements. Backstresses in a material point and those between neighboring points are treated separately. Physically backstresses can dynamically induce either hardening or softening effects to adjust the dislocation hardening of slip systems, whereas the sum of the stresses resulting in backstresses in the representative volume element (RVE) is zero. Backstress hardening suppresses certain slip activities, while backstress softening triggers excess dislocations. A two-phase brass is studied. Backstresses make the hard phase deform smaller and the soft phase deform more than those without employing backstresses in a model. In the former, more homogeneous lattice strain and higher yield stress are obtained. Backstress has limited effects on the evolution of the critical resolved shear stress and crystallographic texture. Furthermore, it is a major cause of the banded structures featuring sharp crystallographic contrasts which are not parallel to the slip planes. Tests indicate that backstress induces a serrated behavior at the early stages of deformation and induces the geometrically necessary bands (GNBs), which are parallel to the macroscopic axes.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Connectivity-Dependent Exciton–Phonon Coupling in Cesium Bismuth Halide Quantum Dots

Metal halide octahedra form the fundamental functional building blocks of metal halide perovskites, dictating their structures, optical properties, electronic structures, and dynamics. Here, in this study, we show that the connectivity of bismuth halide octahedra in Cs 3 Bi 2 Br 9 and Cs 3 Bi 2 I 9 quantum dots (QDs) changes with different halide elements. We use first-principles calculations to reveal the key role of the connectivity of bismuth halide octahedra on the wave function symmetry, Huang-Rhys factor, and exciton-phonon interaction strength. Following QD synthesis via a ligand-mediated transport method, the effect of connectivity is verified with transient absorption spectroscopy, where we contrast Cs 3 Bi 2 Br 9 and Cs 3 Bi 2 I 9 QD exciton dynamics. In photoexcited Cs 3 Bi 2 I 9 QDs, phonons related to the vibrational motions of face-sharing [BiI 6 ] 3- bioctahedra couple strongly to the electronic state and drive rapid carrier relaxation. Equivalent signals are not observed for photoexcited Cs 3 Bi 2 Br 9 QDs, implying a lack of phonon involvement in band-edge absorption and subsequent exciton relaxation. Our findings suggest that structural engineering can effectively tune the exciton-phonon coupling and therefore influence exciton relaxation and recombination in perovskite nanomaterials.

TDDFT↗
DOE OSTI2022

Tuning moiré excitons and correlated electronic states through layer degree of freedom

Moiré coupling in transition metal dichalcogenides (TMDCs) superlattices introduces flat minibands that enable strong electronic correlation and fascinating correlated states, and it also modifies the strong Coulomb-interaction-driven excitons and gives rise to moiré excitons. Here, we introduce the layer degree of freedom to the WSe 2 /WS 2 moiré superlattice by changing WSe 2 from monolayer to bilayer and trilayer. We observe systematic changes of optical spectra of the moiré excitons, which directly confirm the highly interfacial nature of moiré coupling at the WSe 2 /WS 2 interface. In addition, the energy resonances of moiré excitons are strongly modified, with their separation significantly increased in multilayer WSe 2 /monolayer WS 2 moiré superlattice. The additional WSe 2 layers also modulate the strong electronic correlation strength, evidenced by the reduced Mott transition temperature with added WSe 2 layer(s). The layer dependence of both moiré excitons and correlated electronic states can be well described by our theoretical model. Our study presents a new method to tune the strong electronic correlation and moiré exciton bands in the TMDCs moiré superlattices, ushering in an exciting platform to engineer quantum phenomena stemming from strong correlation and Coulomb interaction.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Determination of electron-hole pair creation energy in Cd 0.9 Zn 0.1 Te 0.98 Se 0.02 quaternary semiconductor for room-temperature gamma-ray detection

We report the first-time measurement of the electron-hole pair (ehp) creation energy (W ehp ) in novel Cd 0.9 Zn 0.1 Te 0.98 Se 0.02 (CZTS) quaternary semiconductor. CZTS in single crystalline form is poised to be the future of large-volume room-temperature gamma-ray detectors due to its excellent compositional homogeneity with highly reduced defects, high-Z (atomic number) constituents, wide bandgap (1.6 eV), and superior charge transport properties. Despite a great deal of study of the material and device properties since its inception, the W ehp in CZTS has not been measured experimentally. Accurate determination of W ehp is essential for calibration of the spectrometer and other theoretical calculations. In this study we have used an absolute calibration approach, which is based on an iterative approach that yields the Wehp as the best-fit parameter. Using a 241 Am alpha emitting radioisotope and a planar CZTS detector, the Wehp in CZTS was calculated to be 4.47 eV. The obtained value has been validated by accurately predicting the peak energy for gamma rays emitted by a 137 Cs source and read by a CZTS detector with different dimensions. The dependences of the calculated W ehp value on the detector dimensions, type of interaction, and effect of charge trapping are also discussed.

42 ENGINEERING↗