Results for “blanket” — Page 16

NASA NTRS2021

Relocatable 10 kW Solar Array for Lunar South Pole Missions

Deployable, relocatable, free-standing solar arrays are being developed to provide modular power for future lunar South Pole missions. Major design requirements for these arrays will be low mass, compact launch stowage, and highly reliable deployment and retraction. This paper presents a novel conceptual design for a10 kW solar array to address these requirements referred to as the Relocatable Solar Array (RSA).Simply stated, the concept is a pair of solar cell blankets freely hanging from a horizontal cross arm supported by a vertical, slender, telescoping mast resting on a deployable tripod base. A major factor in simplifying the design is that the force exerted by lunar gravity is used to deploy and maintain extension of the hanging array blankets. A second major factor in achieving the desired low mass and high volumetric efficiency is that the array operates in the vacuum, low-gravity, lunar environment with no deployed vibration frequency requirement. Such a low-load environment enables use of extraordinarily slender and low mass structural members to support the hanging array blankets. This concept was developed, in part, to serve as a NASA reference solar array concept against which other proposed arrays can be compared.

Lunar Surface Power↗

NASA NTRS2022

Passive Cooling in Aerogel-Based Insulation Systems for Liquid Hydrogen Upper Stage Launch Vehicle Tanks

Spray-On Foam Insulation (SOFI) is typically used to protect the windward-facing side of flight tanks for space launch vehicle liquid hydrogen (LH2) stages. SOFI is an excellent insulator in ambient pressure environments, however, its performance pales in comparison to reflective-type systems such as Multi-Layer Insulation in the thermal radiation dominated vacuum environment of space. If a windward insulation system employing radiation shields could be devised to replace or supplement SOFI, the on-orbit heat load could be drastically reduced, and the residual propellants could then be used to facilitate secondary missions. Such insulation systems, utilizing aerogel blanket insulation, have been explored by the Cryogenics Test Laboratory at NASA Kennedy Space Center. Owing to its nano-porous structure, aerogel is an excellent adsorbent as well as an insulator at cryogenic temperatures and will readily uptake condensable background gasses such as air when protecting a surface near LH2 temperatures. When an adsorbed blanket is rapidly exposed to a vacuum, such as during the ascent of a rocket, it will release the background gas, producing a passive cooling effect that could potentially reduce or eliminate the heat load on the propellant tank for a time. This work discusses the setup and results of a test program carried out to determine the effectiveness and impact of this cooling effect as it pertains to LH2 upper stage tanks. A vertical-cylindrical liquid nitrogen (LN2) calorimeter test instrument acted as the upper stage analog. The cold-mass was wrapped with two layers of 10 mm thick aerogel blanket material, with and without aluminum heat shields depending on the test, and interspersed with numerous thermocouple temperature sensors. Gaseous argon was used as a stand-in for air as the condensable background gas. The test procedure mimicked vehicle cryo-loading/stabilization, and ascent phases, with the ascent phase accomplished using parallel vacuum pumps. Results show that the desorption cooling effect was enough to not only eliminate the heat load on the LN2 cold-mass entirely, but further refrigerated the liquid below its boiling point.

A.M. Swanger↗

NASA NTRSDate not supplied

A Survey of ISS and Visiting Vehicle Returned Surfaces for Environmental Characterization and Computer Model Development

The Orbital Debris Engineering Model (ORDEM) developed by the NASA Orbital Debris Program Office (ODPO) is a data-driven model — extensive radar, optical, laboratory, and in situ measurement data sets have been used to build the model since its earliest versions. A salient aspect of professional software development is the verification and validation (V&V) process. Verification answers the question “Is the model built correctly?” while validation addresses the question “Did we build the correct model?” Less extensive, reserved, or independent data sets serve the validation requirement. Due to the dynamic nature of the orbital debris environment, it is critical to use contemporaneous data sources that represent the current environment to support ORDEM development and validation. ORDEM has utilized in situ data collected from Space Shuttle and Hubble Space Telescope surface inspections, now over a decade old. This historical dataset is fundamental for providing baseline in situ measurement data for sizes between 10 to 300 microns, but new data sources are being evaluated using returned surfaces from or near the International Space Station (ISS). This paper reviews a general microscopic survey of ISS soft goods, the Pressurized Mating Adapter 2 (PMA-2) blanket, and a limited-scope feasibility study conducted on the Space Exploration Technologies Corporation (SpaceX) Dragon capsule’s Thermal Protection System (TPS) material. The PMA-2 blanket, exposed to the space environment between 09 July 2013 and 25 February 2015, is an approximately 3.7 m2-area blanket composed of a betacloth outer layer and multiple ballistic fabric inner layers. The SpaceX Cargo Dragon capsule regularly visited the ISS from 2012 through 2020 and potentially provides a timely and well-characterized source of data for modeling purposes. The capsule’s lateral surfaces use SpaceX Proprietary Ablative Material (SPAM) TPS material, a syntactic foam, for thermal management during all mission phases. Seven SPAM extracted samples have been analyzed to date. This paper will provide an overview of the characterization completed for impact features by size, depth, impactor diameter, and the impactor residues chemical analyses, allowing a differentiation between micrometeoroids and orbital debris and a categorization by mass density and density class. Impactor diameter is estimated using damage equations generated from ground-based hypervelocity impact testing. The orbital debris impactors are compared to the current ORDEM 3.2 model of the environment at ISS altitudes. We briefly discuss the meteoroid impactors, including constituents and mass densities, in the general context of current models.

Phillip Anz-meador↗

NASA NTRSDate not supplied

A Survey of ISS and Visiting Vehicle Returned Surfaces for Environmental Characterization and Computer Model Development

The Orbital Debris Engineering Model (ORDEM) developed by the NASA Orbital Debris Program Office (ODPO) is a data-driven model — extensive radar, optical, laboratory, and in situ measurement data sets have been used to build the model since its earliest versions. A salient aspect of professional software development is the verification and validation (V&V) process. Verification answers the question “Is the model built correctly?” while validation addresses the question “Did we build the correct model?” Less extensive, reserved, or independent data sets serve the validation requirement. Due to the dynamic nature of the orbital debris environment, it is critical to use contemporaneous data sources that represent the current environment to support ORDEM development and validation. ORDEM has utilized in situ data collected from Space Shuttle and Hubble Space Telescope surface inspections, now over a decade old. This historical dataset is fundamental for providing baseline in situ measurement data for sizes between 10 to 300 microns, but new data sources are being evaluated using returned surfaces from or near the International Space Station (ISS). This paper reviews a general microscopic survey of ISS soft goods, the Pressurized Mating Adapter 2 (PMA-2) blanket, and a limited-scope feasibility study conducted on the Space Exploration Technologies Corporation (SpaceX) Dragon capsule’s Thermal Protection System (TPS) material. The PMA-2 blanket, exposed to the space environment between 09 July 2013 and 25 February 2015, is an approximately 3.7 m2-area blanket composed of a betacloth outer layer and multiple ballistic fabric inner layers. The SpaceX Cargo Dragon capsule regularly visited the ISS from 2012 through 2020 and potentially provides a timely and well-characterized source of data for modeling purposes. The capsule’s lateral surfaces use SpaceX Proprietary Ablative Material (SPAM) TPS material, a syntactic foam, for thermal management during all mission phases. Seven SPAM extracted samples have been analyzed to date. This paper will provide an overview of the characterization completed for impact features by size, depth, impactor diameter, and the impactor residues chemical analyses, allowing a differentiation between micrometeoroids and orbital debris and a categorization by mass density and density class. Impactor diameter is estimated using damage equations generated from ground-based hypervelocity impact testing. The orbital debris impactors are compared to the current ORDEM 3.2 model of the environment at ISS altitudes. We briefly discuss the meteoroid impactors, including constituents and mass densities, in the general context of current models.

Phillip Anz-Meador↗

NASA NTRS2023

Alternate Approach to Multi Layer Insulation Modeling to Reduce Node Count

For models with a limitation on the overall node count, the typical approach to Multi-Layer Insulation (MLI) modeling may generate nodes that are necessary for the analysis, but do not represent components of particular interest. This leaves fewer nodes that can be utilized to model components of greater importance than the MLI. A common approach to modeling MLI is to include a separate MLI node representing the outer layer of the insulation and a radiative coupling based on the area multiplied by an effective emissivity. Therefore, wherever insulation is included, one node is needed for the underlying surface and another node for the insulation. Since many spacecraft and instruments include MLI covering a sizable portion of their designs, this may result in a considerable number of nodes being used for MLI. An alternate method to MLI modeling was developed that eliminates the MLI node, while still preserving the effect of the insulation for the underlying surface, thereby increasing the available nodes that could be used elsewhere in the model. This approach relies on preserving the baseline reflectivity, while reducing the absorptivity (based on the blanket effective emittance) and including a transparency. An inactive second surface is placed just behind the base surface that fully absorbs any energy that is transmitted without including its effect in the model. In essence, this approach applies only the energy that makes it through the blanket to the underlying surface. This method was tested out on the Roman Space Telescope model in local areas in preparation for its use in the generation of a launch model, which is constrained in the allowable node count. This paper documents the performance of the method and presents a comparison between the One-Node MLI method and the traditional two node MLI approach.

Thermal↗

NASA NTRS1972

The absolute energy flux envelopes of B type stars.

Absolute energy flux envelopes covering the region of 1100 to 6000 A for main-sequence stars of types B3, B7 and A0 derived from published, ground-based observations and from spectrum scans with OAO-II are presented. These flux envelopes are compared with the predicted flux envelopes from lightly line-blanketed model atmospheres. The line blanketing at wavelengths shorter than 3000 A is severe, about one-half the predicted light being observed at 1600 A. These results demonstrate that a model which represents well the observed visible spectrum of a star may fail seriously for representing the ultraviolet spectrum.

Underhill, A. B.↗

NASA NTRS1972

Feasibility study of a 110 watt per kilogram lightweight solar array system

An investigation of the feasibility of a solar array panel subsystem which will produce 10,000 watts of electrical output at 1 A.U. with an overall beginning-of-life power-to-weight ratio of at least 110 watt/kg is reported. A description of the current baseline configuration which meets these requirements is presented. A parametric analysis of the single boom, two blanket planar solar array system was performed to arrive at the optimum system aspect ratio. A novel concept for the stiffening of a lightweight solar array by canting the solar cell blankets at a small angle to take advantage of the inherent in-plane stiffness to increase the symmetric out-of-plane frequency is introduced along with a preliminary analysis of the stiffening effect. A comparison of welded and soldered solar cell interconnections leads to the conclusion that welding is required on this ultralightweight solar array. The use of a boron/aluminum composite material in a BI-STEM type deployable boom is investigated as a possible advancement in the state-of-the-art.

Shepard, N. F.↗

NASA NTRS1972

Artificial lunar impact craters: Four new identifications, part I

The Apollo 16 panoramic camera photographed the impact locations of the Ranger 7 and 9 spacecraft and the S-4B stage of the Apollo 14 Saturn launch vehicle. Identification of the Ranger craters was very simple because each photographed its target point before impact. Identification of the S-4B impact crater proved to be a simple matter because the impact location, as derived from earth-based tracking, displayed a prominent and unique system of mixed light and dark rays. By using the criterion of a dark ray pattern, a reexamination of the Apollo 14 500 mm Hasselblad sequence taken of the Apollo 13 S-4B impact area was made. This examination quickly led to the discovery of the ray system and the impact crater. The study of artificial lunar impact craters, ejecta blankets, and ray systems provides the long-needed link between the various experimental terrestrial impact and explosion craters, and the naturally occurring impact craters on the moon. This elementary study shows that lunar impact crater diameters are closely predictable from a knowledge of the energies involved, at least in the size range considered, and suggests that parameters, such as velocity, may have a profound effect on crater morphology and ejecta blanket albedo.

Whitaker, E. A.↗

NASA NTRS1972

King Crater and its environs, part M

Superb photographs of King Crater were returned by the Apollo 16 crew. The metric and panoramic cameras provided stereoscopic coverage with which high quality topographic maps may be made. King crater, approximately 75 km in diameter and, on the average, 3.8 km deep, is among the most significant features photographed and visually studied from lunar orbit on the Apollo 16 mission. It is the freshest crater on the far side in its size range and has several unique characteristics. (1) Although its ejecta blanket displays very sharp features, the crater does not appear to have extensive ray systems and secondary crater chains. (2) As depicted for the first time by Apollo 16 photographs, the ejecta blanket is strewn with numerous flow fronts and scarps. (3) A flat and smooth, dark, lavalike deposit 15 km across is on the northern rim of the crater. (4) The central peak of the crater is a Y-shaped structure that begins at the southern rim. (5) Bright units that are aligned with the central peak on the northern wall and rim suggest that a preexisting tabular body was excavated by the cratering process.

El-Baz, F.↗

NASA NTRS1973

Nuclear Analysis

Exploratory calculations were performed for several gas core breeder reactor configurations. The computational method involved the use of the MACH-1 one dimensional diffusion theory code and the THERMOS integral transport theory code for thermal cross sections. Computations were performed to analyze thermal breeder concepts and nonbreeder concepts. Analysis of breeders was restricted to the (U-233)-Th breeding cycle, and computations were performed to examine a range of parameters. These parameters include U-233 to hydrogen atom ratio in the gaseous cavity, carbon to thorium atom ratio in the breeding blanket, cavity size, and blanket size.

Clement, J. D.↗

NASA NTRS1973

Ultraviolet photometry from the Orbiting Astronomical Observatory. VII alpha squared Canum Venaticorum.

Far-ultraviolet photometry by OAO-2 is presented for alpha squared CVn covering the entire 5.47-day period of this magnetic Ap variable. The light curves ranging from 1330 to 3320 A indicate that there are two important sources of back warming from far-ultraviolet absorption. Strong line blanketing by the rare earths redistributes flux longward of the Balmer discontinuity, causing the major observed photometric variations. In addition, a second source, which may be due to a combination of continuous opacities and line blanketing from the iron-peak and rare-earth groups below 1600 A, apparently redistributes flux into the region of the Balmer discontinuity. It is also found that ground-based determinations of the effective temperature are overestimated due to the flux redistribution from far-ultraviolet absorption. The effective temperature of alpha squared CVn derived from OAO and ground-based absolute fluxes is found to be 11,200 K, which remains constant over the cycle.

Molnar, M. R.↗

NASA NTRS1973

Lunar magnetic anomalies and the Cayley formation

It is proposed that magnetic anomalies such as found at the Apollo 16 site are associated with breccia flows which cooled in place from above 770 C. The required field at the time that this process took place is a few thousand gamma. It is suggested that the surface and orbital magnetic anomalies are caused by basins filled with Cayley-like breccia flows to a thickness of the order of a kilometer. These breccia blankets settled in place from temperatures above 770 C and a thickness on the order of 1 km was welded to a level of 2 to 4 on Warner's scale. A base surge caused by impact or by a volcanic event could be the mechanism by which these breccia blankets were deposited.

Strangway, D. W.↗

NASA NTRS1974

Predicting spacecraft multilayer insulation performance from heat transfer measurements

Multilayer insulation (MLI) ideally consists of a series of radiation shields with low-conductivity spacers. When MLI blankets were installed on cryogenic tanks or spacecraft, a large discrepancy between the calorimeter measurements and the performance of the installed blankets was discovered. It was found that discontinuities such as exposed edges coupled with high lateral heat transfer created 'heat leaks' which overshadowed the basic heat transfer of the insulation. Approaches leading to improved performance predictions of MLI units are discussed.

Stimpson, L. D.↗

NASA NTRS1974

Lunar basin formation and highland stratigraphy

Multiring impact basins, formed after solidification of the lunar crust, account for most or all premare regional deposits and structures expressed in the lunar landscape and for major topographic and gravity variations. A fresh basin has two or more concentric mountain rings, a lineated ejecta blanket, and secondary impact craters. Crackled material on the floor may be impact melt. The ejecta blanket was emplaced at least partly as a ground-hugging flow and was probably hot. A suggested model of basin formation is that the center lifts up and the rings form by inward collapse during evisceration. The resulting basin is shallow and has a central uplift of the mantle. This results in a central gravity high and a ring low. Later flooding by mare basalt has since modified most near side basins. Highland deposits of plains, furrowed and pitted terrain, and various hills, domes, and craters that were interpreted before the Apollo missions as being volcanic can now be interpreted as being basin related.

Howard, K. A.↗

NASA NTRS1975

Design and fabrication of a flexible tunnel for Sortie Laboratory

A program was conducted to update a prototype design and to fabricate a flexible tunnel for a space shuttle/spacelab interface structure. The significant changes in the prototype are as follows: (1) elimination of foam from bladder laminate to increase bladder flexibility, (2) heat treat pulley brackets, bolts, and hinge pin to 160,000 psi minimum tensile strength, and (3) reduction of the meteoroid barrier from 0.5 inch to 0.375 inch. The thermal blanket installation study resulted in developing a method of installation by properly folding the various layers so that a uniform thickness could be maintained under the clamps. A single-lobe mockup was fabricated and cycled open and closed several times with no apparent damage to the blanket.

Source record↗

NASA NTRS1975

The life and times of Big Bertha - Lunar breccia 14321

The assembly and metamorphic history of polymict breccia 14321 are reconstructed. The earliest formed fragmental component of 14321 (microbreccia-1) is dominated by KREEP-rich norite, extruded and subsequently brecciated and lithified in an ejecta blanket at approximately 1000 C in the general region of Mare Imbrium after the Serenitatis impact but prior to the Imbrium impact. This early microbreccia component and lesser amounts of mare-type basalt, microgranite, rhyolite glass, anorthosite and olivine microbreccia were assembled at the Apollo 14 site as part of the Fra Mauro ejecta blanket from the Imbrium impact. The resulting microbreccia-3 incorporates all the lithic types above and accretionary lapilli structures (microbreccia-2) in a dark matrix annealed at approximately 700 C. A later impact on the Fra Mauro excavated and mutually abraded microbreccia-3 and a local, 14321-type, basalt which were assembled into polymict breccia 14321. Final placement of 14321 at its sampling location was accomplished during the minor Cone Crater impact event.

Duncan, A. R.↗

NASA NTRS1975

Evaluation of low cost/high temperature insulation, July 1974 - June 1975

Six fiber products and six insulation blankets comprising silica, alumina, zirconia, mullite, and mixed ceramic systems were subjected to furnace exposures up to 500 hours at temperatures of 1000 to 1600 C and evaluated for chemical and dimensional stability and for changes in thermal conductivity. Alumina, zirconia, and mullite fibers were fabricated into reusable surface insulation (RSI) tile by water-felting and reimpregnation with ethyl silicate. Specimens were exposed to 25 thermal cycles at 1200 C and 1400 C and a pressure of 10 and 32 torr, respectively. Production costs for 930 sq m (10,000 sq ft) of blanket insulation and of alumina RSI tile were developed.

Strauss, E. L.↗

NASA NTRS1976

Thermal performance of a customized multilayer insulation (MLI)

The thermal performance of a LH2 tank on a shroudless vehicle was investigated. The 1.52 m (60 in) tank was insulated with 2 MLI blankets consisting of 18 double aluminized Mylar radiation shields and 19 silk net spacers. The temperature of outer space was simulated by using a cryoshroud which was maintained at near liquid hydrogen temperature. The heating effects of a payload were simulated by utilizing a thermal payload simulator (TPS) viewing the tank. The test program consisted of three major test categories: (1) null testing, (2) thermal performance testing of the tank installed MLI system, and (3) thermal testing of a customized MLI configuration. TPS surface temperatures during the null test were maintained at near hydrogen temperature and during test categories 2 and 3 at 289 K (520R). The heat flow rate through the tank installed MLI at a tank/TPS spacing of 0.457 m was 1.204 watts with no MLI on the TPS and 0.059 watts through the customized MLI with three blankets on the TPS. Reducing the tank/TPS spacing from 0.457 m to 0.152 m the heat flow through the customized MLI increased by 10 percent.

Leonhard, K. E.↗