SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The basic nature of composite materials is considered. Carbon fiber composites and their area of current and planned application in civil aircraft are discussed, specifically within the framework of the various aspects of risk analysis.
The average exposure to carbon fibers which produced a short and potential shock hazard in a household toaster was determined. Toasters are normally in the off state. They are used for brief periods during the day and have timed cycles during which power is applied. The possibility of a short occurring from the heating element to the case was investigated to find the exposure levels at which a potential shock hazard could appear. The short produced was tested to determine its importance.
The probabilistic and statistical aspects of the carbon fiber risk assessment modeling of fire accidents involving commercial aircraft are examined. Three major sources of uncertainty in the modeling effort are identified. These are: (1) imprecise knowledge in establishing the model; (2) parameter estimation; and (3)Monte Carlo sampling error. All three sources of uncertainty are treated and statistical procedures are utilized and/or developed to control them wherever possible.
Insoluble, even coating formed by soaking in polyacrylic acid. Carbon fiber material prepared by soaking in solution of 20 percent polyacrylic acid in water. Material blotted and dried at 120 degrees C for at least 2 hours. Dried material reacted with boiling aqueous solution of calcium acetate. Treated material removed from boiling solution, blotted, dried at 120 degrees C, washed with distilled water, and dried again.
The damage tolerance of structures made of carbon-fiber-reinforced plastic is tested under various loads. Test laminate (73/1/1, 24/9/1, 1465 A) specimens of thickness 1.5-3.2 mm with various defects were subjected to static and dynamic loads. Special attention was given to delamination, and ultrasonic C-scans were made on the specimens. It was shown that cracks from even small defects are detected with great accuracy. The same probes were also X rayed; defects that could not be detected under ordinary X rays were bored and studied under vacuum by a contrast technique. The nondestructive ultrasonic and X ray tests were controlled by partially destructive tests, and good agreement was observed.
Copper chloride intercalated pitch-based carbon fibers are found to have electrical resistivities as low as 12.9 micro-ohm-cm, and are air- and thermally-stable at and above room temperature. This is therefore a good candidate system for conductor application. In addition, Shubnikov-deHaas quantum oscillatory effects were found, and electronic properties of the intercalated fiber are studied using magnetic fields to 20 tesla.
Tooling is an integral part of composites manufacturing. Composite tools, also called ‘soft’ tools, are more easily constructed than ‘hard’ metal tools and, because they are made from materials similar to the manufactured composite part, they can be made in-house and have a good co-efficient of thermal expansion match. However, as the ‘soft’ designation suggests, they are more vulnerable to wear and typically find application in relatively low-volume production. Additive manufacturing of thermoplastics has proven to be a lucrative option that can help improve the tooling functionalities, as it offers more design flexibility. Owing to the inherent nature of additive manufacturing, the possibility of printing sensors within the tool material and at proximity to otherwise inaccessible areas of the tool become a reality. Continuous carbon fiber (CCF)-reinforced three-dimensional (3D) printing of engineering thermoplastics has proven to be a viable option to strengthen a part well beyond the ideal moduli of unmodified thermoplastic. Furthermore, adding nanotubes or graphene to the thermoplastic matrix will also improve both the thermal conductivity and interlaminar shear strength within the tool. Carbon nanotubes (CNTs) and carbon fibers (CFs) are microwave susceptors; exploiting the physics of Joule heating to increase the energy efficiency of tool hardening and cure rates is a core goal of this project. Because of the rapid volumetric heating enabled by the absorption of microwave or radio frequency energy and electromagnetic (EM) annealing presents an attractive opportunity to significantly reduce manufacturing cycle times while improving part performance.
Defluorination of graphite fluoride (CFX) by heating to temperatures of 250 to 450 C in chemically reactive environments was studied. This is a new and possibly inexpensive process to produce new carbon-based materials. For example, CF 0.68 fibers, made from P-100 carbon fibers, can be defluorinated in BrH2C-CH = CH-CH2Br (1,4-dibromo-2butene) heated to 370 C, and graphitized to produce fibers with an unusually high modulus and a graphite layer structure that is healed and cross-linked. Conversely, a sulfur-doped, visibly soft carbon fiber was produced by defluorinating CF 0.9 fibers, made from P-25, in sulfur (S) vapor at 370 C and then heating to 660 C in nitrogen (N2). Furthermore, defluorination of the CF 0.68 fibers in bromine (Br2) produced fragile, structurally damaged carbon fibers. Heating these fragile fibers to 1100 C in N2 caused further structural damage, whereas heating to 150 C in bromoform (CHBr3) and then to 1100 C in N2 healed the structural defects. The defluorination product of CFX, tentatively called activated graphite, has the composition and molecular structure of graphite, but is chemically more reactive. Activated graphite is a scavenger of manganese (Mn), and can be intercalated with magnesium (Mg). Also, it can easily collect large amounts of an alloy made from copper (Cu) and type 304 stainless steel to form a composite. Finally, there are indications that activated graphite can wet metals or ceramics, thereby forming stronger composites with them than the pristine carbon fibers can form.
Hybrid tooling is an emerging concept introduced in the aerospace industries to reduce weight and cost of traditional tools. A hybrid tool features a skin, which provides desired surface quality, durability, and a low-density substrate to reduce the weight of the mold. The big area additive manufacturing (BAAM) technology permits rapid production of thermoplastic polymer intensive large-scale structures. The present study features a carbon fiber reinforced polyphenylene sulfide (CF-PPS) substrate fabricated using Oak Ridge National Laboratory's BAAM system. Carbon fiber-bismaleimide (CF-BMI) prepreg skin was then bonded to the BAAM tool through high-pressure autoclave molding. Process optimization was conducted to improve the bonding between CF-PPS and CF-BMI (transverse tensile strength increased from 0.54 to 4.8 MPa). Durability of the mold was demonstrated from fabricating seven (7) carbon fiber-Huntsman epoxy hand lay-up parts utilizing the mold.
Ultraviolet-enhanced chemical vapor deposition (UVCVD) has been developed to lower the required substrate temperature thereby allowing for the application of metal oxide-based coatings to carbon and ceramic fibers without causing significant fiber damage. An effort to expand this capability to other ceramic phases chosen to maximize oxidation protection in the likely event of matrix cracking and minimize possible reaction between the coating and fiber during long-term high temperature use will be presented along with studies aimed at the demonstration of these and other benefits for the next-generation interface coating systems being developed herein.
With a better balance among good mechanical performance, high freedom of design, and low material and manufacturing cost, chopped carbon fiber chip reinforced sheet molding compound (SMC) composites show great potential in different engineering applications. Here in this paper, bending fatigue behaviors of SMC composites considering the heterogeneous fiber orientation distributions have been thoroughly investigated utilizing both experimental and computational methods. First, four-point bending fatigue tests are performed with designed SMC composites, and the local modulus is adopted as a metric to represent the local fiber orientation of two opposing sides. Interestingly, SMC composites with and without large discrepancy in local modulus of opposing sides show different fatigue behaviors. Interrupted tests are conducted to explore the bending fatigue failure mechanism, and the damage processes of valid specimens are also closely examined. We find that the fatigue failure of SMC composites under four-point bending is governed by crack propagation instead of crack initiation. Because of this, the heterogeneous local fiber orientations of both sides of the specimen influence fatigue life. The microstructure of the lower side shows a direct influence while that of the upper side also exhibiting influence which becomes more prominent for high cycle fatigue cases. Furthermore, a hybrid micro–macro computational model is proposed to efficiently study the cyclic bending behavior of SMC composites. The region of interest is reconstructed with a modified random sequential absorption algorithm to conserve all the microstructural details including the heterogeneous fiber orientation, while the rest of the regions are modeled as homogenized macro-scale continua. Combined with a framework to capture the progressive fatigue damage under cyclic bending, the bending fatigue behaviors of SMC composites are accurately captured by the hybrid computational model comparing with our experimental analysis.
Advanced unidirectional and bidirectional carbon fiber/epoxy resin composites were evaluated for physical and mechanical properties over a cryogenic to room temperature range for potential application to cryogenic vessels. The results showed that Courtaulds HTS carbon fiber was the superior fiber in terms of cryogenic strength properties in epoxy composites. Of the resin systems tested in ring composites, CTBN/ERLB 4617 exhibited the highest composite strengths at cryogenic temperatures, but very low interlaminar shear strengths at room temperature. Tests of unidirectional and bidirectional composite bars showed that the Epon 828/Empol 1040 resin was better at all test temperatures. Neither fatigue cycling nor thermal shock had a significant effect on composite strengths or moduli. Thermal expansion measurements gave negative values in the fiber direction and positive values in the transverse direction of the composites.
This study focuses on the notch effect on the fatigue failure of chopped carbon fiber chip-reinforced sheet molding compound (SMC) composites by using both experimental and numerical methods. The S-N diagrams of notched specimens are first obtained experimentally, which exhibit large scatter and are shown to depend on the spatial distribution of local fiber orientations. After considering the effect of this spatial distribution by adopting a new fatigue damage parameter to normalize the results, we achieve a much better correlation in the normalized S-N diagram for all the notched specimens with different hole diameters. Next, compared with the fatigue results of smooth specimens without notches, we find that SMC composites under tension-tension fatigue loading exhibit notch-insensitivity, which renders this type of composites a better candidate in joints or similar applications. Meanwhile, the fatigue failure mechanisms of notched SMC composites are explored through a microstructure characterization procedure. On this basis, a computational micromechanics model considering the notch effect and an improved multi-scale progressive damage fatigue law, calibrated by coupon-level fatigue tests of smooth SMC composites under different loading conditions, are employed to predict the fatigue behavior of notched SMC composites. We show that detailed failure processes and fatigue life of notched SMC composites can be efficiently and adequately predicted by this computational framework.
The aim of this project is to reduce the cost of Type IV, carbon fiber (CF) composite overwrap compressed gas storage tanks by reducing the cost of CF and CF composites. The project team worked to reduce the cost of CF by exploring and testing opportunities for a low-cost alternative precursor material for CF production to supplant market-dominant and costly polyacrylonitrile (PAN). Concurrently, the team aimed to reduce the cost of the tanks at the composite level by improving the interfacial adhesion between the fibers and the matrix resin through the incorporation of low-cost nanoparticles recycled from waste materials, which would reduce the volume of costly CF required to achieve the same tank performance. At the end of the first year, the project team selected mesophase pitch as the primary precursor candidate from a field of materials based on the superior mechanical performance and cost-saving potential. During the second year, the team produced CFs derived from mesophase pitch achieving an average tensile strength of 365.6 ksi and average tensile modulus of 40.74 Msi. Facility availability for spinning and converting these fibers at greater scale has hindered scale-up demonstration, but the team has identified opportunities to conduct this work in the near term. Cost modeling shows that these mesophase pitch-derived CFs can be up to 40% less expensive than PAN-derived CFs due to the lower cost of the feedstock material, higher throughput, greater conversion yield, and lower cost spinning method and compared to PAN. Additionally, the team has demonstrated at lab-scale that nanoparticle coating CFs can significantly increase the interfacial shear strength and load transfer efficiency of CFs in a matrix. Single filament pull-out testing showed a 27% average increase in max interfacial shear strength due to this coating. A continuous method of applying these coatings to a tow of CF has been developed for scale-up. 26 m tows of coated CFs were produced using this system and formed into composite ring samples for ASTM ring burst testing. Issues with the testing protocol have limited assessment of these results. A prototype Type IV tank was designed to meet ANSI HGV2 standards, and the design criteria set out by DOE, using the CF properties developed by the team paired with a proprietary resin matrix, a polyamide liner, and aluminum end bosses. The tank weighs 153.1 kg and with a total capacity of 5.8 kg H2 (5.6 kg usable), which yields a gravimetric capacity of 1.17 kWh/kg. Cost modeling predicts that the tank will have a projected cost of $15.73/kWh. Tank performance modeling does not include considerations for fiber-matrix load transfer efficiency improvements offered by nanoparticle coating method.
The fraction of carbon fibers passing through a water separator and an air filter was determined in order to estimate the proportion of fibers outside a closed aircraft that are transmitted to the electronics through the air conditioning system. When both devices were used together and only fibers 3 mm or larger were considered, a transfer function of .001 was obtained.
The manufacturing process, test procedures and application of high strength, high modulus carbon fibers are described in this patent document.
Experimental measurements of the electrical resistivity vs temperature of methane vapor grown carbon fibers are presented. The fibers are heat treated from 1100 C (as-grown) to 3000 C. Data are fit to a standard two band model, which yields values for boundary scattering limited electron mobility, in-plane mean free path, energy band overlap, and total carrier density. The data are also fit to an ellipsoidal band model, where data fits yield effective masses, band overlap, Fermi velocity, phonon contributions to scattering, and ionized impurity scattering rates.
This work considers a unique wide tow (450k filaments) form of low-cost carbon fiber intended for non-aerospace applications. TCF is currently produced in epoxy and urethane sizing, and there is a need to understand its resulting composite properties. In this work, the interfacial adhesion of sized TCF reinforced in thermoset urethane (TSU) composites are examined through the surface, thermal and mechanical characterization techniques. Atomic force microscopy (AFM) results showed an increase in surface roughness for urethane (276%) and epoxy sized (78%) versus unsized TCF. XPS results showed 531% increase in O in epoxy sized TCF and 250% N content in urethane sized TCF compared to unsized TCF. The surface energy of epoxy and urethane sized TCF is enhanced by 78% and 96%, respectively compared to unsized TCF. The storage modulus showed improvement for urethane (23%) and epoxy (21%) sized than unsized TCF-TSU composites. The flexural, interlaminar shear strength (ILSS), and impact properties of urethane sized TCF increase by 24%, 50%, and 273%, respectively, than unsized TCF. The results demonstrate that the surface and thermal properties correlate with the mechanical properties of TCF-TSU composites and sizing enhances the wettability of the composites.