Search NASA⌕ Search

SEARCH · Search NASA

Results for “compression rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

Evolution of microstructure and strength of a high entropy alloy undergoing the strain-induced martensitic transformation

In a recent work, we have reported outstanding strength and work hardening exhibited by a metastable high entropy alloy (HEA), Fe 42 Mn 28 Co 10 Cr 15 Si 5 (in at. %), undergoing the strain-induced martensitic transformation from metastable gamma austenite (γ) to stable epsilon martensite (ε). However, the alloy exhibited poor ductility, which was attributed to the presence of the brittle sigma (σ) phase in its microstructure. The present work reports the evolution of microstructure, strength, and ductility of a similar HEA, Fe 38.5 Mn 20 Co 20 Cr 15 Si 5 Cu 1.5 (in at. %), designed to suppress the formation of σ phase. A cast and then rolled plate of the alloy was processed into four conditions by annealing for 10 and 30 min at 1100 °C and by friction stir processing (FSP) at tool rotation rates of 150 and 400 revolutions per minute (RPM) to facilitate detailed examinations of variable initial grain structures. Neutron diffraction and electron microscopy were employed to characterize the microstructure and texture evolution. The initial materials had variable grain size but nearly 100% γ structure. Diffusionless strain induced γ→ε phase transformation took place under compression with higher rate initially and slower rate at the later stages of deformation, independent on the initial grain size. The transformation facilitated part of plastic strain accommodation and rapid strain hardening owing to a transformation-induced dynamic Hall-Petch-type barrier effect, increase in dislocation density, and texture. Here, the peak strength of nearly 2 GPa was achieved under compression using the structure created by double pass FSP (150 RPM followed by 150 RPM). Remarkably, the tensile elongation exhibited by the alloy was nearly 20% with fracture surfaces featuring a combination of ductile dimples and cleavage.

36 MATERIALS SCIENCE↗

Analysis of the Factors Contributing to Vertebral Compression Fractures After Spine Stereotactic Radiosurgery

Purpose: To determine our institutional vertebral compression fracture (VCF) rate after spine stereotactic radiosurgery (SRS) and determine contributory factors. Methods and Materials: Retrospective analysis from 2001 to 2013 at a single institution was performed. With institutional review board approval, electronic medical records of 1905 vertebral bodies from 791 patients who were treated with SRS for the management of primary or metastatic spinal lesions were reviewed. A total of 448 patients (1070 vertebral bodies) with adequate follow-up imaging studies available were analyzed. Doses ranging from 10 Gy in 1 fraction to 60 Gy in 5 fractions were delivered. Computed tomography and magnetic resonance imaging were used to evaluate the primary endpoints of this study: development of a new VCF, progression of an existing VCF, and requirement of stabilization surgery after SRS. Results: A total of 127 VCFs (11.9%; 95% confidence interval [CI] 9.5%-14.2%) in 97 patients were potentially SRS induced: 46 (36%) were de novo, 44 (35%) VCFs progressed, and 37 (29%) required stabilization surgery after SRS. Our rate for radiologic VCF development/progression (excluding patients who underwent surgery) was 8.4%. Upon further exclusion of patients with hematologic malignancies the VCF rate was 7.6%. In the univariate analyses, females (hazard ratio [HR] 1.54, 95% CI 1.01-2.33, P=.04), prior VCF (HR 1.99, 95% CI 1.30-3.06, P=.001), primary hematologic malignancies (HR 2.68, 95% CI 1.68-4.28, P<.001), thoracic spine lesions (HR 1.46, 95% CI 1.02-2.10, P=.02), and lytic lesions had a significantly increased risk for VCF after SRS. On multivariate analyses, prior VCF and lesion type remained contributory. Conclusions: Single-fraction SRS doses of 16 to 18 Gy to the spine seem to be associated with a low rate of VCFs. To the best of our knowledge, this is the largest reported experience analyzing SRS-induced VCFs, with one of the lowest event rates reported.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

PDF turbulence modeling and DNS

The problem of time discontinuity (or jump condition) in the coalescence/dispersion (C/D) mixing model is addressed in probability density function (pdf). A C/D mixing model continuous in time is introduced. With the continuous mixing model, the process of chemical reaction can be fully coupled with mixing. In the case of homogeneous turbulence decay, the new model predicts a pdf very close to a Gaussian distribution, with finite higher moments also close to that of a Gaussian distribution. Results from the continuous mixing model are compared with both experimental data and numerical results from conventional C/D models. The effect of Coriolis forces on compressible homogeneous turbulence is studied using direct numerical simulation (DNS). The numerical method used in this study is an eight order compact difference scheme. Contrary to the conclusions reached by previous DNS studies on incompressible isotropic turbulence, the present results show that the Coriolis force increases the dissipation rate of turbulent kinetic energy, and that anisotropy develops as the Coriolis force increases. The Taylor-Proudman theory does apply since the derivatives in the direction of the rotation axis vanishes rapidly. A closer analysis reveals that the dissipation rate of the incompressible component of the turbulent kinetic energy indeed decreases with a higher rotation rate, consistent with incompressible flow simulations (Bardina), while the dissipation rate of the compressible part increases; the net gain is positive. Inertial waves are observed in the simulation results.

Hsu, A. T.↗

Experimental study of vorticity-strain rate interaction in turbulent partially-premixed jet flames using tomographic particle image velocimetry

In turbulent flows, the interaction between vorticity, ω, and strain rate, s, is considered a primary mechanism for the transfer of energy from large to small scales through vortex stretching. The ω-s coupling in turbulent jet flames is investigated using tomographic particle image velocimetry (TPIV). TPIV provides a direct measurement of the three-dimensional velocity field from which ω and s are determined. The effects of combustion and mean shear on the ω-s interaction are investigated in turbulent partially premixed methane/air jet flames with high and low probabilities of localized extinction as well as in a non-reacting isothermal air jet with Reynolds number of approximately 13,000. Results show that combustion causes structures of high vorticity and strain rate to agglomerate in highly correlated, elongated layers that span the height of the probe volume. In the non-reacting jet, these structures have a more varied morphology, greater fragmentation, and are not as well correlated. The enhanced spatiotemporal correlation of vorticity and strain rate in the stable flame results in stronger ω-s interaction characterized by increased enstrophy and strain-rate production rates via vortex stretching and straining, respectively. The probability of preferential local alignment between ω and the eigenvector of the intermediate principal strain rate, s 2 , which is intrinsic to the ω-s coupling in turbulent flows, is larger in the flames and increases with the flame stability. The larger mean shear in the flame imposes a preferential orientation of ω and s 2 tangential to the shear layer. The extensive and compressive principal strain rates, s 1 and s 3 , respectively, are preferentially oriented at approximately 45° with respect to the jet axis. As a result, the production rates of strain and vorticity tend to be dominated by instances in which ω is parallel to the s 1 ¯-s 2 ¯ plane and orthogonal to s 3 ¯.

42 ENGINEERING↗

The role of breakup and coalescence in fine-scale bubble-induced turbulence. II. Kinematics

This second part of our research explores the kinematic aspect of fine-scale bubble-induced turbulence (BIT) to (i) present the effect of bubble breakup and coalescence and (ii) compare it against the universal kinematic fine-scale turbulence characteristics reported in the literature. To this end, we simulate a dilute bubbly system of 0.5% void fraction using two distinct numerical simulations. In the volume-of-fluid (VoF) simulation, bubbles undergo breakup and coalescence. In the immersed boundary method (IBM) simulation, however, they act as rigid spheres. We also perform a simulation of classical homogeneous isotropic turbulence (HIT). The first important outcome of this study is that BIT is radically different from HIT in terms of its kinematic fine-scale characteristics. In the vorticity-dominating regions, BIT exhibits a weak vortex stretching. This weak vortex stretching is due to (a) the intermediate strain-rate eigenvalues skewed weakly to positive and (b) the extensive strain-rate eigenvector aligning perpendicular to the vorticity vector. The BIT has, on average, not only a weak enstrophy production but also a weak strain production in strain-dominating regions. The weak strain production is due to (a) the presence of vortex stretching in highly strained fluid elements and (b) the absolute magnitude of compressive strain-rate eigenvalue being as close to the extensive strain-rate eigenvalue. Thus, none of the kinematic fine-scale HIT characteristics is noted for BIT. The second important conclusion is that bubble breakup and coalescence play little to no influence on the kinematics of fine-scale BIT as VoF and IBM simulations produce similar results.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High speed X-ray phase contrast imaging of energetic composites under dynamic compression

Fracture of crystals and subsequent frictional heating are associated with formation of hot spots in energetic composites such as polymer bonded explosives (PBXs). Traditional high speed optical imaging methods cannot be used to study the dynamic sub-surface deformation and fracture behavior of such materials due to their opaque nature. In this study, high speed synchrotron X-ray experiments are conducted to visualize the in situ deformation and fracture mechanisms in PBXs manufactured using octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) crystals and hydroxyl-terminated polybutadiene (HTPB) binder. A modified Kolsky bar apparatus was used to apply controlled dynamic compression on the PBX specimens, and a high speed synchrotron X-ray phase contrast imaging (PCI) setup was used to record the in situ deformation and failure in the specimens. The experiments show that synchrotron X-ray PCI provides a sufficient contrast between the HMX crystals and the doped binder, even at ultrafast recording rates. Under dynamic compression, most of the cracking in the crystals was observed to be due to the tensile stress generated by the diametral compression applied from the contacts between the crystals. Tensile stress driven cracking was also observed for some of the crystals due to the transverse deformation of the binder and superior bonding between the crystal and the binder. In conclusion, the obtained results are vital to develop improved understanding and to validate the macroscopic and mesoscopic numerical models for energetic composites so that eventually hot spot formation can be predicted.

36 MATERIALS SCIENCE↗

A finite-strain rate- and pressure-dependent constitutive framework for analyzing shock compression behavior of cemented tungsten carbides to 100 GPa

In the present study a thermodynamically-consistent finite-strain rate-and-pressure-dependent constitutive framework is implemented to analyze the shock-compression behavior of cemented tungsten carbides to 100 GPa. Central to this framework is the use of logarithmic strain with a set of invariant basis that allow the Cauchy stress tensor to be expressed as a sum of three response terms that are mutually orthogonal, thus permitting a complete separation of the deviatoric and volumetric (pressure) response. An overstress viscoplasticity model that includes strain and strain rate hardening along with thermal softening is used to represent the deviatoric response, while a complete Mie-Grüneisen equation of state (EoS) is used to obtain the pressure response. Using this formulation, the shock-induced compression behavior of cemented tungsten carbide - obtained from planar plate impact experiments using a 30 mm powder gun to peak stresses of up to ~100 GPa - is analyzed to better understand the structure of the measured shock wave profiles and the associated in-material shock quantities. Of particular interest is the evolution of material inelasticity and strength, and temperature in the tungsten carbide samples during the shock compression process.

Cemented tungsten carbide↗

Reconnection in compressible plasmas: Extended conversion region

The classical Sweet-Parker approach to steady-state magnetic reconnection is extended into the regime of large resistivity (small magnetic Reynolds or Lundquist number) when the aspect ratio between the outflow and inflow scale, {delta} = d/L, approaches unity. In a previous paper [Paper I, Hesse et al., Phys. Plasmas 18, 042104 (2011)], the vicinity of the dissipation site (''diffusion region'') was investigated. In this paper, the approach is extended to cover larger sites, in which the energy transfer and conversion is not confined to the diffusion region. Consistent with the results of Paper I, we find that increasing aspect ratio {delta} is associated with increasing compression, increasing reconnection rate for low {beta}, but slightly decreasing rate for higher {beta}, decreasing outflow speed, and increasing outflow magnetic field. These trends are stronger for lower {beta}. Deviations from the traditional Sweet-Parker limit {delta}{yields} 0 become significant for R{sub m}<{approx}10, where R{sub m} is the magnetic Reynolds number (Lundquist number) based on the half-thickness of the current layer responsible for the Ohmic dissipation. They are also more significant for small {gamma}, that is, for increasing compressibility. In contrast to the results of Paper I, but consistent with earlier results for {delta}<<1, we find that in this limit the outflow speed is given by the Alfven speed {nu}{sub A} in the inflow region and the energy conversion is given by an even split of Poynting flux into enthalpy flux and bulk kinetic energy flux. However, with increasing {delta} the conversion to enthalpy flux becomes more and more dominant.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Evaluating temperature and fuel stratification for heat-release rate control in a reactivity-controlled compression-ignition engine using optical diagnostics and chemical kinetics modeling

We investigated the combustion process in a dual-fuel, reactivity-controlled compression-ignition (RCCI) engine using a combination of optical diagnostics and chemical kinetics modeling to explain the role of equivalence ratio, temperature, and fuel reactivity stratification for heat-release rate control. An optically accessible engine is operated in the RCCI combustion mode using gasoline primary reference fuels (PRF). A well-mixed charge of iso-octane (PRF = 100) is created by injecting fuel into the engine cylinder during the intake stroke using a gasoline-type direct injector. Later in the cycle, n-heptane (PRF = 0) is delivered through a centrally mounted diesel-type common-rail injector. This injection strategy generates stratification in equivalence ratio, fuel blend, and temperature. The first part of this study uses a high-speed camera to image the injection events and record high-temperature combustion chemiluminescence. Moreover, the chemiluminescence imaging showed that, at the operating condition studied in the present work, mixtures in the squish region ignite first, and the reaction zone proceeds inward toward the center of the combustion chamber. The second part of this study investigates the charge preparation of the RCCI strategy using planar laser-induced fluorescence (PLIF) of a fuel tracer under non-reacting conditions to quantify fuel concentration distributions prior to ignition. The fuel-tracer PLIF data show that the combustion event proceeds down gradients in the n-heptane distribution. The third part of the study uses chemical kinetics modeling over a range of mixtures spanning the distributions observed from the fuel-tracer fluorescence imaging to isolate the roles of temperature, equivalence ratio, and PRF number stratification. The simulations predict that PRF number stratification is the dominant factor controlling the ignition location and growth rate of the reaction zone. Equivalence ratio has a smaller, but still significant, influence. Lastly, temperature stratification had a negligible influence due to the NTC behavior of the PRF mixtures.

42 ENGINEERING↗

Unsteady transition measurements on a pitching three-dimensional wing

Boundary layer transition measurements were made during an experimental study of the aerodynamics of a rectangular wing undergoing unsteady pitching motions. The wing was tested at chordwise Mach numbers between 0.2 and 0.6, at sweep angles of 0, 15, and 30 deg, and for steady state, sinusoidal, and constant pitch rate motions. The model was scaled to represent a full size helicopter rotor blade, with chord Reynolds numbers between 2 and 6 x 10(exp 6). Sixteen surface hot-film gages were located along three spanwise stations: 0.08, 0.27, and 0.70 chords from the wing tip. Qualitative heat transfer information was obtained to identify the unsteady motion of the point of transition to turbulence. In combination with simultaneous measurements of the unsteady surface pressure distributions, the results illustrate the effects of compressibility, sweep, pitch rate, and proximity to the wing tip on the transition and relaminarization locations.

Lorber, Peter F.↗

Temperature distortion generator for turboshaft engine testing

The procedures and unique hardware used to conduct an experimental investigation into the response of a small-turboshaft-engine compression system to various hot gas ingestion patterns are presented. The temperature distortion generator described herein uses gaseous hydrogen to create both steady-state and time-variant, or transient, temperature distortion at the engine inlet. The range of transient temperature ramps produced by the distortion generator during the engine tests was from less than 111 deg K/sec (200 deg R/sec) to above 611 deg K/sec (1100 deg R/sec); instantaneous temperatures to 422 deg K (760 deg R) above ambient were generated. The distortion generator was used to document the maximum inlet temperatures and temperature rise rates that the compression system could tolerate before the onset of stall for various circumferential distortions as well as the compressor system response during stall.

Klann, G. A.↗

Temperature distortion generator for turboshaft engine testing

The procedures and unique hardware used to conduct an experimental investigation into the response of a small-turboshaft-engine compression system to various hot gas ingestion patterns are presented. The temperature distortion generator described herein uses gaseous hydrogen to create both steady-state and time-variant, or transient, temperature distortion at the engine inlet. The range of transient temperature ramps produced by the distortion generator during the engine tests was from less than 111 deg K/sec (200 deg R/sec) to above 611 deg K/sec (1100 deg R/sec); instantaneous temperatures to 422 deg K (760 deg R) above ambient were generated. The distortion generator was used to document the maximum inlet temperatures and temperature rise rates that the compression system could tolerate before the onset of stall for various circumferential distortions as well as the compressor system response during stall.

Klann, G. A.↗

Vector-based feedback of continuous wave radiofrequency compression cavity for ultrafast electron diffraction

The temporal resolution of ultrafast electron diffraction at weakly relativistic beam energies (⁠≲100 keV) suffers from space-charge induced electron pulse broadening. We describe the implementation of a radio frequency (RF) cavity operating in the continuous wave regime to compress high repetition rate electron bunches from a 40.4 kV DC photoinjector for ultrafast electron diffraction applications. Active stabilization of the RF amplitude and phase through a feedback loop based on the demodulated in-phase and quadrature components of the RF signal is demonstrated. This scheme yields 144 ± 19 fs RMS temporal resolution in pump–probe studies.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Quasi-static to Dynamic Response and Microstructure Development of Tantalum-Tungsten Alloys

Lawrence Livermore National Laboratory (LLNL) has a need to understand the quasi-static to dynamic mechanical response and microstructure evolution of tantalum-tungsten (Ta-W) alloys made by conventional wrought processing and additive manufacturing (AM). This two-year work scope will be performed at the Colorado School of Mines (Mines) and will include quasi-static (e.g., 10 -3 s -1 ) mechanical testing in tension and compression, along with high strain rate (Kolsky) pressure bar testing in tension and compression (e.g., 10 3 s -1 ), without and with temperature variations. Gas gun experiments at higher strain rates (e.g., over 10 3 s -1 ) will also be pursued. Complementary microstructure characterization will be performed on undeformed and deformed samples to fundamentally understand the role of processing on the microstructure characteristics and resulting deformation mechanisms that dictate the mechanical response of these alloys with variations in strain rate, temperature, and strain state. Alloys of interest will be Ta-based, containing up to 10 wt.% W. LLNL will supply initial wrought-processed material for sample machining. LLNL will also supply samples built by AM during the project for testing. Arc melting and casting may also be performed at Mines to produce small quantities of different alloys for machining and exploratory testing on an as-needed basis. This project will support multiple postdocs and graduate students at Mines, training them with the knowledge, skills, and abilities needed to study materials under extreme conditions of interest to the National Nuclear Security Agency.

36 MATERIALS SCIENCE↗

Strain-rate/temperature behavior of high density polyethylene in compression

The compressive strain rate/temperature behavior of highly linear, high density polyethylene was analyzed in terms of the predictive relations developed for metals and other crystalline materials. For strains of 5 percent and above, the relationship between applied strain rate, dotted epsilon, and resulting flow stress, sigma, was found to be: dotted epsilon exp times (Q sub f/RT) = k'(sigma/sigma sub c) to the nth power; the left-hand side is the activation-energy-compensated strain rate, where Q sub f is activation energy for flow, R is gas constant, and T is temperature; k is a constant, n is temperature-independent stress exponent, and sigma/sigma sub c is structure-compensated stress. A master curve resulted from a logarithmic plot of activation-energy-compensated strain rate versus structure-compensated stress.

Clements, L. L.↗

Compressibility Effects on the Growth and Structure of Homogeneous Turbulent Shear Flow

Compressibility effects within decaying isotropic turbulence and homogeneous turbulent shear flow have been studied using direct numerical simulation. The objective of this work is to increase our understanding of compressible turbulence and to aid the development of turbulence models for compressible flows. The numerical simulations of compressible isotropic turbulence show that compressibility effects are highly dependent on the initial conditions. The shear flow simulations, on the other hand, show that measures of compressibility evolve to become independent of their initial values and are parameterized by the root mean square Mach number. The growth rate of the turbulence in compressible homogeneous shear flow is reduced compared to that in the incompressible case. The reduced growth rate is the result of an increase in the dissipation rate and energy transfer to internal energy by the pressure-dilatation correlation. Examination of the structure of compressible homogeneous shear flow reveals the presence of eddy shocklets, which are important for the increased dissipation rate of compressible turbulence.

Blaisdell, G. A.↗

Effect of compressibility on the Rayleigh-Taylor and Richtmyer-Meshkov instability induced nonlinear structure at two fluid interface

The effect of compressibility and of density variation on Rayleigh-Taylor and Richtmyer-Meshkov instability of the temporal development of two fluid interfacial structures such as bubbles and spikes have been investigated. It is seen that the velocity of the tip of the bubble or spike increases (destabilization) if the local Atwood number increases due to density variation of either of the fluids. The opposite is the result, i.e., the bubble or spike tip velocity decreases (stabilization) if the density variation leads to lowering of the value of the local Atwood number. The magnitude of stabilization or destabilization is an increasing function of the product of the wave number k and interfacial pressure p{sub 0}. The effect of compressibility is quite varied. If the heavier (upper) fluid alone is incompressible ({gamma}{sub h}{yields}{infinity}), but the lighter fluid is compressible the growth rate is higher (destabilization) than when both the fluids are incompressible. Moreover the heavier fluid remaining incompressible the growth rate decreases (stabilization) as {gamma}{sub l} (finite) increases and ultimately tends to the incompressible limit value as {gamma}{sub l}{yields}{infinity}. With {gamma}{sub l}{yields}{infinity} but {gamma}{sub h} finite the growth increases (destabilization) as {gamma}{sub h} increases. When both {gamma}{sub h} and {gamma}{sub l} are finite (density {rho}{sub h}>density {rho}{sub l}) the growth is reduced when {gamma}{sub h}<{gamma}{sub l} compared to that when both fluids are incompressible and enhanced when {gamma}{sub h}>{gamma}{sub l}. The set of nonlinear equations describing the dynamics of bubbles and spikes in the presence of fluid density variations are not analytically integrable in closed form. The results derived by numerical solution methods are represented and interpreted in corresponding figures.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Mechanical Behavior of UO 2 at Sub-grain Length Scales: Quantification of Elastic, Plastic and Creep Properties via Microscale Testing

Techniques were developed to measure properties at sub-grain scales using depleted Uranium Oxide (d-UO2) samples heat-treated to obtain different grain sizes and oxygen stoichiometries, through three main tasks: 1) sample processing and characterization, 2) microscale and conventional testing and 3) modeling. Grain size and crystallography were characterized using Scanning Electron Microscopy (SEM), in conjunction with Electron Backscattering Diffraction (EBSD) and Electron Channeling Contrast Imaging (ECCI). Grains were then carefully selected based on their crystallographic orientations to perform ex-situ micromechanical tests with samples machined via Focused Ion Beam (FIB), with emphasis on micro-cantilever bending. These experiments were performed under controlled atmospheres, to insure stoichiometry control, at temperatures up to 700 °C and allowed measurements involving elastic (effective Young’s modulus), plastic (critical resolved shear stresses) and creep (creep strain rates) behavior. Conventional compression experiments were performed simultaneously to compare with the ex-situ measurements and study potential size effects. Modeling was implemented using anisotropic elasticity and inelastic constitutive relations for plasticity and creep based on kinematics and kinetics of dislocation glide that account for the effects of crystal orientation, and stress. The models will be calibrated and validated using the experimental data. This project provided insight on correlations among stoichiometry, crystallography and mechanical behavior in advanced oxide fuels, provided valuable experimental data to validate and calibrate mesoscale fuel performance codes and also a framework to measure sub-grain scale mechanical properties that should be suitable for use with irradiated samples due to small volumes required. The goals and metrics of the ongoing study of thermo-mechanical behavior in depleted uranium dioxide (d-UO 2 ) outlined in this project have been concluded successfully, resulting in: 1) the successful fabrication, processing, and characterization of large-grained samples with various orientations (up to and including single crystals) having stoichiometric and hyper-stoichiometric O/U ratios; 2) formulation, calibration, and validation of a crystal plasticity constitutive model to describe the creep deformation of UO 2 at the sub-grain length scale (single crystal level) at intermediate temperatures; 3) the successful calibration of a crystal plasticity constitutive model to describe the elasto-plastic deformation of microcantilever beams, also at moderate temperatures. Samples were prepared from natural uranium oxide powder of production-quality provided by Areva. The powder was pressed in a die to a pressure of 100 MPa to produce green pellets with no sintering aids, lubricants, or any other additives. The green pellets were then heated up to 1700 °C under ultra-high purity argon atmosphere (~1 ppm O2). The atmosphere was then changed to 79% Argon, 21% O 2 and the temperature was held at 1700 °C for 2 hours to sinter the pellets under oxidative conditions [1] that are known to increase grain growth kinetics in UO 2 [2]. Samples were then cooled down under Ar-4%H2 atmosphere to reduce the samples back to stoichiometric UO 2 . For macro-scale procedures, testing of UO 2 samples with large grains was performed at 1200 °C using a modified load frame capable of applying dead-weight loads to ensure constant stress conditions, while displacement of the sample produced by the applied load was measured with high precision micrometers to obtain strains. Stress steps were used during testing and the strains were monitored to measured creep strain rates under steady state for each level of stress used, so that stress exponents could be obtained. The results of the mechanical testing, along with sample geometry and crystal orientation of the grains in the samples, as well as post-test sample characterization were used to formulate a viscoplastic model to account for steady state (stage II) creep behavior, along with basic assumptions from crystal plasticity and kinematic constraints due to testing fixtures. In the micro-scale, testing of microcantilever beams at temperatures ranging from 25 to 570 °C was performed in-situ with a scanning electron microscope with a special attachment to apply load and measure displacement while the samples were at temperature. The load-displacement curves obtained showed linear behavior before fracture for all temperatures attempted except 570 °C, where clear deviations from non-linearity were observed before fracture. These deviations were consistently observed for all samples tested for a given orientation. A viscoplastic model was used to account for the presence of inelastic strain, along with basic assumptions from crystal plasticity and beam theory. These models were kept as simple as possible, and results from tests performed in a set of samples with a given crystal orientation were used to calibrate the material constants for the model, while results from a different sample set were then used for validation, thus satisfying the conditions of all main tasks within the parameters of this project. Details of these efforts are outlined in this report.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗