Results for “damage testing systems” — Page 16

NASA NTRS1980

Chemical vapor deposited tungsten with dispersed carbides for Space Shuttle check valves

A chemical vapor deposited tungsten with dispersed carbides was selected as the material for Space Shuttle Orbital Maneuvering and Reaction Control Systems check valve poppets and seats. The selection followed a NASA-sponsored prototype check valve development program utilizing the cutter-seal shell poppet concept. The poppet material is deposited as a coating approximately 0.9 mm thick and fabricated into a shell as a free standing body. The seat material is deposited as a coating 1.1 mm thick on a seat blank, and the cutter seal is machined in the coating. Module tests demonstrated that the material could be ground and lapped to very sharp edges and could cut through typical system contaminants without excessive damage to the sealing surfaces. The material was also determined to be unaffected by exposure to a strongly oxidizing storable propellant.

Williams, G. E.↗

NASA NTRS1995

TBC experience in land based gas turbines

Prior and on-going machine evaluations of TBC coatings for power generation applications are summarized. Rainbow testing of various TBC's on turbine nozzles, shrouds and buckets are described along with one test on combustor liners. GEPG has conducted over 15 machine tests with TBC coated turbine nozzles of various coatings. Rainbow test times generally range between 10,000 to 24,000 hours. TBC performance has been quite good and additional testing, including TBC's on shrouds and buckets is continuing. The results show that TBC's have the capability of surviving in power generation machines for the times required. The earlier rainbow tests which evaluated various top coat compositions resulted in confirmation of the superiority of YSZ and especially the 6-8 YSZ composition. On-going tests are more focused on TBC process and property variations. The prevalent failure modes seen thus far in the various rainbow tests are erosion, foreign object damage and buildup of deposits. Additional post test analysis is required to investigate bond coat oxidation and other time/temperature dependent changes to the system.

Nelson, W. A.↗

NASA NTRS2015

Method and Apparatus for Non-Destructive Evaluation of Materials

Methods and apparatus for characterizing composite materials for manufacturing quality assurance (QA), periodic inspection during the useful life, or for forensic analysis/material testing. System are provided that relate eddy-current sensor responses to the fiber layup of a composite structure, the presence of impact damage on a composite structure with or without a metal liner, volumetric stress within the composite, fiber tow density, and other NDE inspection requirements. Also provided are systems that determine electromagnetic material properties and material dimensions of composite materials from capacitive sensor inspection measurements. These properties are related to the presence of buried defects in non-conductive composite materials, moisture ingress, aging of the material due to service or environmental/thermal exposure, or changes in manufacturing quality.

Goldfine, Neil J.↗

NASA NTRS2017

Method and Apparatus for Non-Destructive Evaluation of Materials

Methods and apparatus for characterizing composite materials for manufacturing quality assurance (QA), periodic inspection during the useful life, or for forensic analysis/material testing. System are provided that relate eddy-current sensor responses to the fiber layup of a composite structure, the presence of impact damage on a composite structure with or without a metal liner, volumetric stress within the composite, fiber tow density, and other NDE inspection requirements. Also provided are systems that determine electromagnetic material properties and material dimensions of composite materials from capacitive sensor inspection measurements. These properties are related to the presence of buried defects in non-conductive composite materials, moisture ingress, aging of the material due to service or environmental/thermal exposure, or changes in manufacturing quality.

Goldfine, Neil J.↗

NASA NTRSDate not supplied

Orion Artemis I As Flown MMOD Analysis

Introduction The Lockheed Martin Orion spacecraft conducted the Artemis I flight around the Moon from November 16 through December 11, 2022. After the flight, an engineer from the NASA Johnson Space Center (JSC) Hypervelocity Impact Technology (HVIT) Group performed a Micrometeoroid and Orbital Debris MMOD analysis using the Bumper 3 risk assessment tool to predict the number of small impacts that would likely have occurred during the mission. Separately, a team from the same group inspected the Orion capsule for hypervelocity impact damage features. The results of the inspection were compared to those of the analysis to aid in improving the analysis, including the environment models. Scope of Work The spacecraft geometry model was created by Lockheed Martin during construction of the Artemis I Orion vehicle based on Computer Aided Design (CAD) models of the vehicle. New hypervelocity impact testing was performed to verify Ballistic Limit Equations (BLEs) used in the analysis to link impactor size and damage to the Thermal Protection System (TPS). The exact trajectory flown was recorded during the flight, including vehicle attitude. This data was used in conjunction with the ORDEM 3.2 and MEM 3 environment modeling tools to create models of particle flux impacting the spacecraft throughout the mission. Meteoroid shower forecast information was also included to account for additional particle flux associated with meteoroid showers. Inspection of the Orion capsule included the Backshell thermal tiles and the tape covering it, windows, fabric thermal materials, and small areas of other materials. Potential MMOD damage found was characterized using various techniques, including optical microscopy, computed tomography scanning, and X-ray spectroscopy. Findings The number of craters found in the Backshell tile, and their size distribution, matches well with the Bumper analysis prediction. Tape, window, and other material impacts recorded similarly align to Bumper analysis predictions. Conclusions and Recommendations This comparison of analysis with inspection of the hardware provides valuable insight into the MMOD environment and how accurately analysis tools assess the impact risk to spacecraft. As this was the first large, non-ablative returned surface from a lunar mission, this analysis extends the MMOD community’s insight beyond low Earth orbit into cis-lunar space.

MMOD↗

NASA NTRSDate not supplied

Orion Artemis I As Flown MMOD Analysis

Introduction The Lockheed Martin Orion spacecraft conducted the Artemis I flight around the Moon from November 16 through December 11, 2022. After the flight, an engineer from the NASA Johnson Space Center (JSC) Hypervelocity Impact Technology (HVIT) Group performed a Micrometeoroid and Orbital Debris MMOD analysis using the Bumper 3 risk assessment tool to predict the number of small impacts that would likely have occurred during the mission. Separately, a team from the same group inspected the Orion capsule for hypervelocity impact damage features. The results of the inspection were compared to those of the analysis to aid in improving the analysis, including the environment models. Scope of Work The spacecraft geometry model was created by Lockheed Martin during construction of the Artemis I Orion vehicle based on Computer Aided Design (CAD) models of the vehicle. New hypervelocity impact testing was performed to verify Ballistic Limit Equations (BLEs) used in the analysis to link impactor size and damage to the Thermal Protection System (TPS). The exact trajectory flown was recorded during the flight, including vehicle attitude. This data was used in conjunction with the ORDEM 3.2 and MEM 3 environment modeling tools to create models of particle flux impacting the spacecraft throughout the mission. Meteoroid shower forecast information was also included to account for additional particle flux associated with meteoroid showers. Inspection of the Orion capsule included the Backshell thermal tiles and the tape covering it, windows, fabric thermal materials, and small areas of other materials. Potential MMOD damage found was characterized using various techniques, including optical microscopy, computed tomography scanning, and X-ray spectroscopy. Findings The number of craters found in the Backshell tile, and their size distribution, matches well with the Bumper analysis prediction. Tape, window, and other material impacts recorded similarly align to Bumper analysis predictions. Conclusions and Recommendations This comparison of analysis with inspection of the hardware provides valuable insight into the MMOD environment and how accurately analysis tools assess the impact risk to spacecraft. As this was the first large, non-ablative returned surface from a lunar mission, this analysis extends the MMOD community’s insight beyond low Earth orbit into cis-lunar space.

MMOD↗

NASA NTRS2001

Fatigue and Damage Tolerance Analysis of a Hybrid Composite Tapered Flexbeam

The behavior of nonlinear tapered composite flexbeams under combined axial tension and cyclic bending loading was studied using coupon test specimens and finite element (FE) analyses. The flexbeams used a hybrid material system of graphite/epoxy and glass/epoxy and had internal dropped plies, dropped in an overlapping stepwise pattern. Two material configurations, differing only in the use of glass or graphite plies in the continuous plies near the midplane, were studied. Test specimens were cut from a full-size helicopter tail-rotor flexbeam and were tested in a hydraulic load frame under combined constant axialtension load and transverse cyclic bending loads. The first determination damage observed in the specimens occurred at the area around the tip of the outermost ply-drop group in the tapered region of the flexbeam, near the thick end. Delaminations grew slowly and stably, toward the thick end of the flexbeam, at the interfaces above and below the dropped-ply region. A 2D finite element model of the flexbeam was developed. The model was analyzed using a geometrically non-linear analysis with both the ANSYS and ABAQUS FE codes. The global responses of each analysis agreed well with the test results. The ANSYS model was used to calculate strain energy release rates (G) for delaminations initiating at two different ply-ending locations. The results showed that delaminations were more inclined to grow at the locations where they were observed in the test specimens. Both ANSYS and ABAQUS were used to calculate G values associated with delamination initiating at the observed location but growing in different interfaces, either above or below the ply-ending group toward the thick end, or toward the thin end from the tip of the resin pocket. The different analysis codes generated the same trends and comparable peak values, within 5-11 % for each delamination path. Both codes showed that delamination toward the thick region was largely mode II, and toward the thin region was predominantly mode I. The calculated peak G-values from either analysis predict delamination is most likely to occur along the same interface where it was observed in the test specimens. Calculated peak G values were used with material characterization data to calculate a curve relating the fatigue life of the specimens, N, to the applied transverse load, V, for a given constant axial load.

Murri, Gretchen B.↗

NASA NTRS2000

Dynamic Capability of an Operating Stirling Convertor

The NASA John H. Glenn Research Center and the US Department of Energy are currently developing a Stirling convertor for use as an advanced spacecraft power system for future NASA deep-space missions. NASA Headquarters has recently identified the Stirling technology generator for potential use as the spacecraft power system for two of NASA's new missions, the Europa Orbiter and the Solar Probe missions (planned for launch in 2006 and 2007 respectively). As part of the development of this power system, a Stirling Technology Demonstration Convertor was vibration tested at NASA John H. Glenn Research Center to verify its survivability and capability of withstanding the harsh dynamic environment typically seen by the spacecraft when it is launched by an expendable launch vehicle. The Technology Demonstration Convertor was fully operational (producing power) during the random vibration testing. The output power of the convertor and other convertor performance indicators were measured during the testing, and these results are discussed in this paper. Numerous accelerometers and force gauges also were used to provide information on the dynamic characteristics of the Technology Demonstration Convertor and as an indication of any possible damage due to the vibration. These measurements will also be discussed in this paper. The vibration testing of the Stirling Technology Demonstration Convertor was extremely successful. The Technology Demonstration Convertor survived all its vibration testing with no structural damage or functional performance degradation. As a result of this testing, the Stirling convertor's capability to withstand vibration has been demonstrated, enabling its usage in future spacecraft power systems.

Goodnight, Thomas W.↗

NASA NTRS2019

Materials and Processes for New Propulsion Systems with Reduced Environmental Impact

Aeronautics research at NASA Glenn Research Center includes development, characterization and modeling of high temperature, lightweight materials and fabrication processes for aircraft propulsion systems with increased efficiency and reduced emissions, fuel burn and noise. Current propulsion materials research includes Ceramic Matrix Composites and Environmental Barrier Coatings, Polymer Matrix Composites and Additive Manufacturing processes. This presentation will summarize recent progress and plans in these areas. Ceramic Matrix Composites for Turbine Components: As part of NASA's Aeronautics research, Glenn Research Center has developed Ceramic Matrix Composites for 2700 degrees Fahrenheit turbine engine applications in the next generation of ultra-efficient aircraft. In this presentation, the development of advanced fiber and matrix constituents that enabled this advancement will be reviewed, and characterization of the resulting improvements in mechanical properties and durability will be summarized. Progress toward the development and validation of models predicting the effects of the engine environment on durability of Ceramic Matrix Composites and Environmental Barrier Coatings will be summarized. Progress and plans for collaborative research with industry and other government agencies will be reviewed. Polymer Matrix Composites for Powertrain and Impact Protection: A lightweight, hybrid polymer matrix composite/steel gear concept for rotorcraft power transmission applications was evaluated at realistic speed, torque, and power conditions. Dynamic testing was performed at 5000 horsepower and 5400 revolutions per minute with no performance degradation. Test results demonstrated the potential of hybrid composite / metal gears to reduce gear weight by approximately 15 percent, enabling the implementation of multi-speed drive systems, which would otherwise have a weight penalty, for increased speed and efficiency. Results of post-test inspection and endurance tests will be presented. Separately, ballistic impact tests demonstrated improved damage tolerance in polymer matrix composites by incorporating lightweight, thermoplastic veil materials between selected composite plies during the composite fabrication process. Results of impact tests and post-test inspection will be presented. Additive Manufacturing for Electric Propulsion: Additive Manufacturing processes offer the potential to fabricate new, high power density electric motor designs with complex geometries, multi-material components and optimally designed components that would not be feasible with traditional manufacturing processes. High performance stator components using advanced 3-phase conductive coils were fabricated using direct printing with optimized silver pastes. Additional additive manufacturing methods are being used to fabricate rotors and motor housing components. Systems studies show that the higher performance and lower weight motors offer improved energy efficiency and reduced emissions. Improvements to motor performance resulting from optimized materials and component designs will be presented.

Additive Manufacturing↗

NASA NTRS1972

Prediction of hail damage to aircraft.

Description of a hailstone impact simulator, a valuable laboratory apparatus which can be used for such hailstone research as the testing of prospective structural designs or generating data to compare with theory. The simulator consists of a launcher and a velocity-measuring system. It has been successfully used to obtain deformation data on flat sheets and spherical caps of various sizes impacted by hailstones at typical flight velocities. A computer program is described which adequately predicts the damage to a simple structure when impacted by a hailstone.

Hayduk, R. J.↗

NASA NTRS1994

Test plan. GCPS task 7, subtask 7.1: IHM development

The overall objective of Task 7 is to identify cost-effective life cycle integrated health management (IHM) approaches for a reusable launch vehicle's primary structure. Acceptable IHM approaches must: eliminate and accommodate faults through robust designs, identify optimum inspection/maintenance periods, automate ground and on-board test and check-out, and accommodate and detect structural faults by providing wide and localized area sensor and test coverage as required. These requirements are elements of our targeted primary structure low cost operations approach using airline-like maintenance by exception philosophies. This development plan will follow an evolutionary path paving the way to the ultimate development of flight-quality production, operations, and vehicle systems. This effort will be focused on maturing the recommended sensor technologies required for localized and wide area health monitoring to a technology readiness level (TRL) of 6 and to establish flight ready system design requirements. The following is a brief list of IHM program objectives: design out faults by analyzing material properties, structural geometry, and load and environment variables and identify failure modes and damage tolerance requirements; design in system robustness while meeting performance objectives (weight limitations) of the reusable launch vehicle primary structure; establish structural integrity margins to preclude the need for test and checkout and predict optimum inspection/maintenance periods through life prediction analysis; identify optimum fault protection system concept definitions combining system robustness and integrity margins established above with cost effective health monitoring technologies; and use coupons, panels, and integrated full scale primary structure test articles to identify, evaluate, and characterize the preferred NDE/NDI/IHM sensor technologies that will be a part of the fault protection system.

Greenberg, H. S.↗

NASA NTRS1986

Testing metals and alloys for use in oxygen systems

When oxygen is present in high concentrations or large quantities, as in oxygen-based life-support systems, the likelihood of combustion and the probable intensity of a conflagration increase, together with the severity of the damage caused. Even stainless steel will burn vigorously when ignited in a 1000-psi oxygen environment. The hazards involved in the use of oxygen increase with system operation at the elevated temperatures typical of propulsion systems. Fires in oxygen systems are generally catastrophic, causing a threat to life in manned vehicles. When mechanical components of a mechanism generate friction heat in the presence of oxygen, many commonly used metal alloys ignite and burn. Attention is presently given to frictional heating, particle impact, and flame propagation tests conducted in oxygen environments.

Stoltzfus, Joel M.↗

NASA NTRS2019

Safe2Ditch Steer-To-Clear Development and Flight Testing

This paper describes a series of small unmanned aerial system (sUAS) flights performed at NASA Langley Research Center in April and May of 2019 to test a newly added Steer-to-Clear feature for the Safe2Ditch (S2D) prototype system. S2D is an autonomous crash management system for sUAS. Its function is to detect the onset of an emergency for an autonomous vehicle, and to enable that vehicle in distress to execute safe landings to avoid injuring people on the ground or damaging property. Flight tests were conducted at the City Environment Range for Testing Autonomous Integrated Navigation (CERTAIN) range at NASA Langley. Prior testing of S2D focused on rerouting to an alternate ditch site when an occupant was detected in the primary ditch site. For Steer-to-Clear testing, S2D was limited to a single ditch site option to force engagement of the Steer-to-Clear mode. The implementation of Steer-to-Clear for the flight prototype used a simple method to divide the target ditch site into four quadrants. An RC car was driven in circles in one quadrant to simulate an occupant in that ditch site. A simple implementation of Steer-to- Clear was programmed to land in the opposite quadrant to maximize distance to the occupant’s quadrant. A successful mission was tallied when this occurred. Out of nineteen flights, thirteen resulted in successful missions. Data logs from the flight vehicle and the RC car indicated that unsuccessful missions were due to geolocation error between the actual location of the RC car and the derived location of it by the Vision Assisted Landing component of S2D on the flight vehicle. Video data indicated that while the Vision Assisted Landing component reliably identified the location of the ditch site occupant in the image frame, the conversion of the occupant’s location to earth coordinates was sometimes adversely impacted by errors in sensor data needed to perform the transformation. Logged sensor data was analyzed to attempt to identify the primary error sources and their impact on the geolocation accuracy. Three trends were observed in the data evaluation phase. In one trend, errors in geolocation were relatively large at the flight vehicle’s cruise altitude, but reduced as the vehicle descended. This was the expected behavior and was attributed to sensor errors of the inertial measurement unit (IMU). The second trend showed distinct sinusoidal error for the entire descent that did not always reduce with altitude. The third trend showed high scatter in the data, which did not correlate well with altitude. Possible sources of observed error and compensation techniques are discussed.

Petty, Bryan J.↗

NASA NTRS2014

Shake Test Results and Dynamic Calibration Efforts for the Large Rotor Test Apparatus

A shake test of the Large Rotor Test Apparatus (LRTA) was performed in an effort to enhance NASAscapability to measure dynamic hub loads for full-scale rotor tests. This paper documents the results of theshake test as well as efforts to calibrate the LRTA balance system to measure dynamic loads.Dynamic rotor loads are the primary source of vibration in helicopters and other rotorcraft, leading topassenger discomfort and damage due to fatigue of aircraft components. There are novel methods beingdeveloped to reduce rotor vibrations, but measuring the actual vibration reductions on full-scale rotorsremains a challenge. In order to measure rotor forces on the LRTA, a balance system in the non-rotatingframe is used. The forces at the balance can then be translated to the hub reference frame to measure therotor loads. Because the LRTA has its own dynamic response, the balance system must be calibrated toinclude the natural frequencies of the test rig.

Shake Test Results↗

NASA NTRS2014

HEMODOSE: A Set of Multi-parameter Biodosimetry Tools

After the events of September 11, 2001 and recent events at the Fukushima reactors in Japan, there is an increasing concern of the occurrence of nuclear and radiological terrorism or accidents that may result in large casualty in densely populated areas. To guide medical personnel in their clinical decisions for effective medical management and treatment of the exposed individuals, biological markers are usually applied to examine the radiation induced changes at different biological levels. Among these the peripheral blood cell counts are widely used to assess the extent of radiation induced injury. This is due to the fact that hematopoietic system is the most vulnerable part of the human body to radiation damage. Particularly, the lymphocyte, granulocyte, and platelet cells are the most radiosensitive of the blood elements, and monitoring their changes after exposure is regarded as the most practical and best laboratory test to estimate radiation dose. The HEMODOSE web tools are built upon solid physiological and pathophysiological understanding of mammalian hematopoietic systems, and rigorous coarse-grained biomathematical modeling and validation. Using single or serial granulocyte, lymphocyte, leukocyte, or platelet counts after exposure, these tools can estimate absorbed doses of adult victims very rapidly and accurately. Some patient data in historical accidents are utilized as examples to demonstrate the capabilities of these tools as a rapid point-of-care diagnostic or centralized high-throughput assay system in a large scale radiological disaster scenario. Unlike previous dose prediction algorithms, the HEMODOSE web tools establish robust correlations between the absorbed doses and victim's various types of blood cell counts not only in the early time window (1 or 2 days), but also in very late phase (up to 4 weeks) after exposure

Hu, Shaowen↗

NASA NTRS1973

Safety monitoring system for radioisotope thermoelectric generators

System alerts personnel of hazards which may develop while they are performing tests on radioisotope thermoelectric generator (RTG). Remedial action is initiated to minimize damage. Five operating conditions are monitored: hot junction temperature, cold junction temperature, thermal shroud coolant flow, vacuum in test chamber, and alpha radiation.

Zoltan, A.↗

NASA NTRS1985

Mechanical protection of DLC films on fused silica slides

Measurements were made with a new test for improved quantitative estimation of the mechanical protection of thin films on optical materials. The mechanical damage was induced by a sand blasting system using spherical glass beads. Development of the surface damage was measured by the changes in the specular transmission and reflection, and by inspection using a surface profilometer and a scanning electron microscope. The changes in the transmittance versus the duration of sand blasting was measured for uncoated fused silica slides and coated ones. It was determined that the diamond like carbon films double the useful optical lifetime of the fused silica. Theoretical expressions were developed to describe the stages in surface deterioration. Conclusions were obtained for the SiO2 surface mechanism and for the film removal mechanism.

Nir, D.↗

NASA NTRS1991

Impact response of composite materials

Composite materials composed of carbon fibers and resin matrices offer great promise in reducing the weight of aerospace structures. However they remain extremely vulnerable to out of plane impact loads, which lead to severe losses in strength and stiffness. The results of an experimental program, undertaken to investigate the low velocity impact damage tolerance of composite materials is presented. The objectives were to identify key neat resin/composite properties that lead to enhancement of composite impact damage tolerance and to find a small scale test that predicts compression after impact properties of panels. Five materials were selected for evaluation. These systems represented different classes of material behavior such as brittle epoxy, modified epoxies, and amorphous and semicrystalling thermoplastics. The influence of fiber properties on the impact performance was also studied in one material, i.e., in polyether ether ketone (PEEK). Several 24 and 48 ply quasi-isotropic and 24 ply orthotropic laminates were examined using an instrumented drop weight impactor. Correlations with post impact compression behavior were made.

Tiwari, S. N.↗