Search NASA⌕ Search

SEARCH · Search NASA

Results for “flaps”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1938

Wind-tunnel of three lateral-control devices in combination with a full-span slotted flap on an NACA 23012 airfoil

A large-chord NACA 23012 airfoil was tested. The airfoil extended completely across the test section, and two-dimensional flow was approximated. The model was fitted with a full-span slotted flap having a chord 25.66 percent of the airfoil chord. The ailerons investigated extended over the entire span and each had a chord 10 percent of the airfoil chord. The types of ailerons tested were: retractable ailerons, slot-lip ailerons using the lip of the slot for ailerons, and plain ailerons on the trailing edge of the slotted flap. The data are presented in the form of curves of section lift, drag, and pitching-moment coefficients for the airfoil with flap deflected but with ailerons neutral, and of rolling-moment, yawing-moment, and hinge-moment coefficients calculated for a rectangular wing of aspect ratio 6 with a semi-span aileron and a full-span flap. For the ailerons investigated the data indicate that, from considerations of rolling and yawing moments produced and of stick forces desired, the retractable aileron is the most satisfactory means of lateral control for use with a full-span slotted flap.

Wenzinger, Carl J↗
NASA NTRS1947

Investigation of Pressure Distribution over an Extended Leading-Edge Flap on a 42 Degrees Sweptback Wing

Pressure distribution over an extended leading-edge flap on a 42 degree swept-back wing was investigated. Results indicate that the flap normal-force coefficient increased almost linearly with the angle of attack to a maximum value of 3.25. The maximum section normal-force coefficient was located about 30 percent of the flap span outboard of the inboard end and had a value of 3.75. Peak negative pressures built up at the flap leading edge as the angle of attack was increased and caused the chordwise location of the flap center of pressure to be move forward.

Conner, D. William↗
NASA NTRS1936

Flight Investigation of Lateral Control Devices for Use with Full-Span Flaps

This report presents the results of flight tests made on five different lateral control devices that appeared adaptable to wings fitted with full span flaps: controllable auxiliary airfoils (airfoils mounted above and forward of the leading edge of the wings), external ailerons (airfoils mounted above the wing and slightly forward of its maximum ordinate), upper-surface ailerons (similar to split trailing-edge flaps except that they constitute the upper surface of the wing), ailerons that retract into the wing when in neutral, and narrow-chord conventional ailerons in combination with a special type of split flap that retracts into the under surface of the wing forward of the ailerons. The devices were tested on a small parasol monoplane. Experienced gained in the use of flaps during these tests has indicated the desirability of a flap that can be operated quickly and easily.

Soule, H A↗
NASA NTRS1937

Aerodynamic Characteristics of NACA 23012 and 23021 Airfoils with 20-Percent-chord External-Airfoil Flaps of NACA 23012 Section

Report presents the results of an investigation of the general aerodynamic characteristics of the NACA 23012 and 23021 airfoils, each equipped with a 0.20c external flap of NACA 23012 section. The tests were made in the NACA 7 by 10-foot and variable-density wind tunnels and covered a range of Reynolds numbers that included values corresponding to those for landing conditions of a wide range of airplanes. Besides a determination of the variation of lift and drag characteristics with position of the flap relative to the main airfoil, complete aerodynamic characteristics of the airfoil-flap combination with a flap hinge axis selected to give small hinge moments were measured in the two tunnels. Some measurements of air loads on the flap itself in the presence of the wing were made in the 7 by 10-foot wind tunnel.

Platt, Robert C↗
NASA NTRS1937

Span load distribution for tapered wings with partial-span flaps

Tables are given for determining the load distribution of tapered wings with partial-span flaps placed either at the center or at the wing tips. Seventy-two wing-flap combinations, including two aspect ratios, four taper ratios, and nine flap lengths, are included. The distributions for the flapped wing are divided into two parts, one a zero lift distribution due primarily to the flaps and the other an additional lift distribution due to an angle of attack of the wing as a whole. Comparison between theoretical and experimental results for wings indicate that the theory may be used to predict the load distribution with sufficient accuracy for structural purposes.

Pearson, H A↗
NASA NTRS1937

Wind-Tunnel Investigation of Wings with Ordinary Ailerons and Full-Span External-Airfoil Flaps

Report presents an investigation carried out in the NACA 7- by 10-foot wind tunnel of an NACA 23012 airfoil equipped, first, with a full-span NACA 23012 external-airfoil flap having a chord 0.20 of the main airfoil chord and with a full-span aileron with a chord 0.12 of the main airfoil chord on the trailing edge of the main airfoil and equipped second, with a 0.30-chord full-span NACA 23012 external-airfoil flap and a 0.13-chord full-span aileron. The results are arranged in three groups, the first two of which deal with the airfoil characteristics of the two airfoil-flap combinations and with the internal-control characteristics of the airfoil-flap-aileron combinations. The third group of tests deals with several means for balancing ailerons mounted on a special large-chord NACA 23012 external-airfoil flap. The tests included an ordinary aileron, a curtained-nose balance, a frise balance, and a tab.

Platt, Robert C↗
NASA NTRS1938

Pressure distribution over an NACA 23012 airfoil with an NACA 23012 external-airfoil flap

Report presents the results of pressure-distribution tests of an NACA 23012 airfoil with an NACA 23012 external airfoil flap made in the 7 by 10-foot wind tunnel. The pressures were measured on the upper and lower surfaces at one chord section on both the main airfoil and on the flap for several different flap deflections and at several angles of attack. A test installation was used in which the airfoil was mounted horizontally in the wind tunnel between vertical end planes so that two-dimensional flow was approximated. The data are presented in the form of pressure-distribution diagrams and as graphs of calculated coefficients for the airfoil-and-flap combination and for the flap alone.

Wenzinger, Carl J↗
NASA NTRS1939

Wind-Tunnel Investigation of an NACA 23012 Airfoil with Various Arrangements of Slotted Flaps

An investigation was made in the 7 by 10-foot wind tunnel and in the variable-density wind tunnel of the NACA 23012 airfoil with various slotted-flap arrangements. The purpose of the investigation in the 7 by 10-foot wind tunnel was to determine the airfoil section aerodynamic characteristics as affected by flap shape, slot shape, and flap location. The flap position for maximum lift; polars for arrangements favorable for take-off and climb; and complete lift, drag, and pitching-moment characteristics for selected optimum arrangements were determined. The best arrangements were tested in the variable-density tunnel at an effective Reynolds number of 8,000,000. In addition, data from both wind tunnels are included for plain, split, external-airfoil, and Fowler flaps for purposes of comparison.

Wenzinger, Carl J↗
NASA NTRS1941

Wind-tunnel investigation of NACA 23012, 23021, and 23030 airfoils equipped with 40-percent-chord double slotted flaps

Report presents the results of an investigation conducted in the NACA 7 by 10-foot win tunnel to determine the effect of the deflection of main and auxiliary slotted flaps on the aerodynamic section characteristics of large-chord NACA 23012, 23021, 23030 airfoils equipped with 40-percent-chord double slotted flaps. The complete aerodynamic section characteristics and envelope polar curves are given for each airfoil-flap combination. The effect of airfoil thickness is shown, and comparisons are made of single slotted flaps with double slotted flaps on each of the airfoils.

Harris, Thomas A↗
NASA NTRS1994

A wind tunnel investigation of the effects of micro-vortex generators and Gurney flaps on the high-lift characteristics of a business jet wing

A study of a full-scale, semi-span business jet wing has been conducted to investigate the potential of two types of high-lift devices for improving aircraft high-lift performance. The research effort involved low-speed wind-tunnel tests of micro-vortex generators and Gurney flaps applied to the flap system of the business jet wing and included force and moment measurements, surface pressure surveys and flow visualization on the wing and flap. Results showed that the micro-vortex generators tested had no beneficial effects on the longitudinal force characteristics in this particular application, while the Gurney flaps were an effective means of increasing lift. However, the Gurney flaps also caused an increase in drag in most circumstances.

Martuccio, Michelle Therese↗
NASA NTRS1995

Blade-Mounted Flap Control for BVI Noise Reduction Proof-of-Concept Test

This report describes a wind tunnel test of the McDonnell Douglas Helicopter Systems (MDHS) Active Flap Model Rotor at the NASA Langley 14- by 22-Foot Subsonic Tunnel. The test demonstrated that BVI noise reductions and vibration reductions were possible with the use of an active flap. Aerodynamic results supported the acoustic data trends, showing a reduction in the strength of the tip vortex with the deflection of the flap. Acoustic results showed that the flap deployment, depending on the peak deflection angle and azimuthal shift in its deployment schedule, can produce BVI noise reductions as much as 6 dB on the advancing and retreating sides. The noise reduction was accompanied by an increase in low frequency harmonic noise and high frequency broadband noise. A brief assessment of the effect of the flap on vibration showed that significant reductions were possible. The greatest vibration reductions (as much as 76%) were found in the four per rev pitching moment at the hub. Performance improvement cam results were inconclusive, as the improvements were predicted to be smaller than the resolution of the rotor balance.

Dawson, Seth↗
NASA NTRS1959

Wind-Tunnel Investigation of a Small-Scale Sweptback-Wing Jet-Transport Model Equipped with an External-Flow Jet-Augmented Double Slotted Flap

A wind-tunnel investigation at low speeds has been made to study the aerodynamic characteristics of a small-scale sweptback-wing Jet-transport model equipped with an external-flow jet-augmented double slotted flap. Included in the investigation were tests of the wing alone to study the effects of varying the spanwise extent of blowing on the full-span flap. The results indicated that the double-slotted-flap arrangement of the present investigation was more efficient in terms of lift and drag than were the external-flow single-slotted-flap arrangements previously tested and gave a substantial reduction In the thrust-weight ratio required for a given lift coefficient under trimmed drag conditions. An increase in the spanwise extent of blowing on the full-span flap was also found to increase the efficiency of the model in terms of the lift and drag but, as would be expected on a sweptback-wing configuration, was accompanied by significant increases in negative pitching moment.

Johnson, Joseph L., Jr.↗
NASA NTRS1958

Lift, Drag, and Pitching Moment of an Aspect-Ratio-2 Triangular Wing with Leading-Edge Flaps Designed to Simulate Conical Camber

An investigation was conducted to determine the effectiveness of leading-edge flaps in reducing the drag at lifting conditions of a triangular wing of aspect ratio 2.0. The flaps, deflected to simulate conically cambered wings having a wide range of design lift coefficients, were tested over a Mach number range of 0.70 to 2.22 through an angle-of-attack variation from -6 deg to +18 deg at a constant Reynolds number of 3.68 million based on the wing mean aerodynamic chord. A symmetrical wing of the same plan form and aspect ratio was also tested to provide a basis for comparison. The experimental results showed that with the flaps in the undeflected position, a small amount of fixed leading-edge droop incorporated over the outboard 5 percent of the wing semispan was as effective at high subsonic speeds as conical camber in improving the maximum lift-drag ratio above that of the symmetrical wing. At supersonic speeds, the penalty in minimum drag above that of the symmetrical wing was less than that incurred by conical camber. Deflecting the leading-edge flaps about the hinge line through 80 percent of the wing semispan resulted in further improvements of the drag characteristics at lift coefficients above 0.20 throughout the Mach number range investigated. The lift and pitching-moment characteristics were not significantly affected by the leading-edge flaps.

Menees, Gene P.↗
NASA NTRS1999

Subsonic Investigation of Leading-Edge Flaps Designed for Vortex- and Attached-Flow on a High-Speed Civil Transport Configuration

A wind tunnel investigation of two separate leading-edge flaps, designed for vortex and attached-flow, respectively, were conducted on a High Speed Civil Transport (HSCT) configuration in the Langley 14- by 22-Foot Subsonic Tunnel. Data were obtained over a Mach number range of 0.12 to 0.27, with corresponding chord Reynolds numbers of 2.50 x 10 (sup 6) to 5.50 x 10 (sup 6). Variations of the leading-edge flap deflection angle were tested with outboard leading-edge flaps deflected 0 deg. and 26.4 deg. Trailing-edge flaps were deflected 0 deg., 10 deg., 12.9 deg., and 20 deg. The longitudinal and lateral aerodynamic data are presented without analysis. A complete tabulated data listing is also presented herein. The data associated with each deflected leading-edge flap indicate L/D improvements over the undeflected configuration. These improvements may be instrumental in providing the necessary lift augmentation required by an actual HSCT during the climb-out and landing phases of the flight envelope. However, further tests will have to be done to assess their full potential.

Campbell, Bryan A.↗
NASA NTRS1991

Handling Qualities Results of an Initial Geared Flap Tilt Wing Piloted Simulation

An exploratory simulation study of a novel approach to pitch control for a tilt wing aircraft was conducted in 1990 on the NASA-Ames Vertical Motion Simulator. The purpose of the study was to evaluate and compare the handling qualities of both a conventional and a geared flap tilt wing control configuration. The geared flap is an innovative control concept which has the potential for reducing or eliminating the horizontal pitch control tail rotor or reaction jets required by prior tilt wing designs. The handling qualities results of the geared flap control configuration are presented in this paper and compared to the conventional (programmed flap) tilt wing control configuration. This paper also describes the geared flap concept, the tilt wing aircraft, the simulation model, the simulation facility and experiment setup, and the pilot evaluation tasks and procedures.

Guerrero, Lourdes M.↗
NASA NTRS2001

In-Flight Flow Visualization Results of The F-106B With a Vortex Flap

Surface and off-surface flow visualization techniques were used to visualize the three-dimensional vortex flows on the F-106 aircraft with vortex flaps installed. Results at angles of attack between 9 deg to 18 deg and Mach numbers from 0.3 to 0.9 are presented. A smoke flow vapor screen technique was used to document leading-edge vortex paths and sizes, while an oil flow technique was employed to provide detailed information on reattachment and separation line locations and other flow details. Results were obtained for two vortex flap deflection angles, 30 deg and 40 deg. Flow visualization revealed the existence of a multiple vortex system that had not previously been seen in subscale tests or predicted for this configuration. The vortex flap generated a leading-edge vortex system that reattached near the flap hinge over a wide angle of attack range. In addition to the primary vortex, flow visualization revealed the presence of several distinct vortices which traced a path from the vortex flap and then over the wing.

Brandon, Jay M.↗
NASA NTRS2003

Active Control of Separation From the Flap of a Supercritical Airfoil

Active flow control in the form of periodic zero-mass-flux excitation was applied at several regions on the leading edge and trailing edge flaps of a simplified high-lift system t o delay flow separation. The NASA Energy Efficient Transport (EET) supercritical airfoil was equipped with a 15% chord simply hinged leading edge flap and a 25% chord simply hinged trailing edge flap. Detailed flow features were measured in an attempt to identify optimal actuator placement. The measurements included steady and unsteady model and tunnel wall pressures, wake surveys, arrays of surface hot-films, flow visualization, and particle image velocimetry (PIV). The current paper describes the application of active separation control at several locations on the deflected trailing edge flap. High frequency (F(+) approx.= 10) and low frequency amplitude modulation (F(+)AM approx.= 1) of the high frequency excitation were used for control. Preliminary efforts to combine leading and trailing edge flap excitations are also reported.

Melton, La Tunia Pack↗
NASA NTRS2003

In-Flight Flow Visualization Results of the F-106B with a Vortex Flap

Surface and off-surface flow visualization techniques were used to visualize the three-dimensional vortex flows on the F-106 aircraft with vortex flaps installed. Results at angles of attack between 9 degrees to 18 degrees and Mach numbers from 0.3 to 0.9 are presented. A smoke flow vapor screen technique was used to document leading-edge vortex paths and sizes, while an oil flow technique was employed to provide detailed information on reattachment and separation line locations and other flow details. Results were obtained for two vortex flap deflection angles, 30 degrees and 40 degrees. Flow visualization revealed the existence of a multiple vortex system that had not previously been seen in subscale tests or predicted for this configuration. The vortex flap generated a leading-edge vortex system that reattached near the flap hinge over a wide angle of attack range. In addition to the primary vortex, flow visualization revealed the presence of several distinct vortices which traced a path from the vortex flap and then over the wing.

Brandon, Jay M.↗