Search NASA⌕ Search

SEARCH · Search NASA

Results for “high crystallinity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Vertically Aligned Single-Crystalline CoFe 2 O 4 Nanobrush Architectures with High Magnetization and Tailored Magnetic Anisotropy

Micrometer-tall vertically aligned single-crystalline CoFe 2 O 4 nanobrush architectures with extraordinarily large aspect ratio have been achieved by the precise control of a kinetic and thermodynamic non-equilibrium pulsed laser epitaxy process. Direct observations by scanning transmission electron microscopy reveal that the nanobrush crystal is mostly defect-free by nature, and epitaxially connected to the substrate through a continuous 2D interface layer. In contrast, periodic dislocations and lattice defects such as anti-phase boundaries and twin boundaries are frequently observed in the 2D interface layer, suggesting that interface misfit strain relaxation under a non-equilibrium growth condition plays a critical role in the self-assembly of such artificial architectures. Further, magnetic property measurements have found that the nanobrushes exhibit a saturation magnetization value of 6.16 μB/f.u., which is much higher than the bulk value. The discovery not only enables insights into an effective route for fabricating unconventional high-quality nanostructures, but also demonstrates a novel magnetic architecture with potential applications in nanomagnetic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High‐Performance Green Thick‐Film Ternary Organic Solar Cells Enabled by Crystallinity Regulation

Abstract The power conversion efficiency (PCE) of organic solar cells (OSCs) has reached high values of over 19%. However, most of the high‐efficiency OSCs are fabricated by spin‐coating with toxic solvents and the optimal photoactive layer thickness is limited to 100 nm, limiting practical development of OSCs. It is a great challenge to obtain ideal morphology for high‐efficiency thick‐film OSCs when using non‐halogenated solvents due to the unfavorable film formation kinetics. Herein, high‐efficiency ternary thick‐film (300 nm) OSCs with PCE of 15.4% based on PM6:BTR‐Cl:CH1007 are fabricated by hot slot‐die coating using non‐halogenated solvent (o‐xylene) in the air. Compared to PM6:BTR‐Cl:Y6 blends, the stronger pre‐aggregation of CH1007 in solution induces the earlier aggregation of CH1007 molecules and longer aggregation time, and thus results in high and balanced crystallinity of donors and acceptor in CH1007‐based ternary film, which led to high‐carrier mobility and suppressed charge recombination. The ternary strategy is further used to fabricate high‐efficiency, thick‐film, large‐area, and flexible devices processed from non‐halogenated solvents, paving the way for industrial development of OSCs.

Chemistry↗
DOE OSTI2023

An in situ formed inorganic conductive network enables high stability and rate capability of single-crystalline nickel-rich cathodes

Single-crystalline Ni-rich cathodes are promising for the next generation of high-energy-density Li-ion batteries due to their better capacity retention than their polycrystalline counterparts. However, there is still much room for improving the electrochemical performances when considering their surface degradation and severe kinetic hindrance during cycling. Herein, we report a strategy to construct an in situ formed robust Li-conductive Li 3 PO 4 layer on the surface of cathode particles. This Li-conductive layer significantly increases the Li-ion diffusion coefficients and suppresses detrimental surface phase transformation. In situ XRD reveals that the improved kinetics alleviate the local stress at high voltage. The as-prepared single-crystalline LiNi 0.83 Co 0.12 Mn 0.05 O 2 delivers good durability (96.8% after 100 cycles at 1C) and excellent rate capability (177.08 mA h g -1 at 5C). Here, this work provides a facile and efficient strategy to improve the cycling performance and boost the rate capability of single-crystalline Ni-rich cathodes.

25 ENERGY STORAGE↗
DOE OSTI2022

Electrodeposition of Complex High Entropy Oxides via Water Droplet Formation and Conversion to Crystalline Alloy Nanoparticles

We report that a combination of electrodeposition and thermal reduction methods have been utilized for the synthesis of ligand-free FeNiCo alloy nanoparticles through a high-entropy oxide intermediate. These phases are of great interest to the electrocatalysis community, especially when formed by a sustainable chemistry method. This is successfully achieved by first forming a complex five element amorphous FeNiCoCrMn high-entropy oxide (HEO) phase via electrodeposition from a nanodroplet emulsion solution of the metal salt reactants. The amorphous oxide phase is then thermally treated and reduced at 570–600 °C to form the crystalline FeNiCo alloy with a separate CrMnO x cophase. The FeNiCo alloy is fully characterized by scanning transmission electron microscopy and energy-dispersive X-ray spectroscopy elemental analysis and is identified as a face-centered cubic crystal with the lattice constant a = 3.52 Å. The unoptimized, ligand-free FeNiCo NPs activity toward the oxygen evolution reaction is evaluated in alkaline solution and found to have an ~185 mV more cathodic onset potential than the Pt metal. Beyond being able to synthesize highly crystalline, ligand-free FeNiCo nanoparticles, the demonstrated and relatively simple two-step process is ideal for the synthesis of tailor-made nanoparticles where the desired composition is not easily achieved with classical solution-based chemistries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Solution-processable and functionalizable ultra-high molecular weight polymers via topochemical synthesis

Abstract Topochemical polymerization reactions hold the promise of producing ultra-high molecular weight crystalline polymers. However, the totality of topochemical polymerization reactions has failed to produce ultra-high molecular weight polymers that are both soluble and display variable functionality, which are restrained by the crystal-packing and reactivity requirements on their respective monomers in the solid state. Herein, we demonstrate the topochemical polymerization reaction of a family of para -azaquinodimethane compounds that undergo facile visible light and thermally initiated polymerization in the solid state, allowing for the first determination of a topochemical polymer crystal structure resolved via the cryoelectron microscopy technique of microcrystal electron diffraction. The topochemical polymerization reaction also displays excellent functional group tolerance, accommodating both solubilizing side chains and reactive groups that allow for post-polymerization functionalization. The thus-produced soluble ultra-high molecular weight polymers display superior capacitive energy storage properties. This study overcomes several synthetic and characterization challenges amongst topochemical polymerization reactions, representing a critical step toward their broader application.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Electrical Analysis of Pulsed Laser Annealed Poly-Si:Ga/SiOx Passivating Contacts

High-efficiency single crystalline silicon (c-Si) solar cells require precise control of dopant diffusion profiles and highly active doping concentrations through thermal annealing. Conventional furnace annealing has been successfully employed for dopant diffusion in aluminum back-surface field (Al-BSF), passivated emitter and rear contact (PERC), and Topcon cells. However, furnace annealing limits some next-generation polycrystalline silicon (poly-Si) on SiOx passivating contacts. This limitation largely affects p-type passivating contacts by not being able to: 1) control the dopant diffusion accurately to prevent B segregation at the SiOx and c-Si interface; and 2) provide highly activated doping concentrations for low contact resistivity. In this contribution, we use a nanosecond excimer laser to examine the passivation quality and electrical performance of both B- and Ga-doped poly-Si/SiOx passivating contacts. The core of this method is to take advantage of the nonequilibrium nature of the anneal through rapid melting and recrystallizing the poly-Si in a short timescale and to achieve doping concentrations above the solid solubility limit. Simulations were performed on polished surfaces to visualize the doping diffusion profiles under different laser conditions, and secondary ion mass spectrometry (SIMS) was used to verify the experimental diffusion profiles post pulsed laser melting (PLM). The results show the dopant diffusion profiles can be tuned precisely through PLM. The electrical analysis using VdP-Hall measurements reveals that the active doping concentration reached 10^21 cm-3 for B and ~2×10^21 cm-3 for Ga in poly-Si, far exceeding their solid solubility limit in Si, with a nearly 100% dopant activation achieved for B, and 20% for Ga. This highly activated dopant profile results in a low contact resistivity of <15 mO·cm^2 for B-doped contacts and <40 mO·cm^2 for Ga-doped contacts. We demonstrate that the passivation quality of the laser annealed contacts shows a linear dependency with the laser energy density and the number of pulses. PLM was also performed on random pyramid textured samples, and we found that preferential melting exists for the tips of pyramids, which can be pursued further for selective pinhole opening. Additionally, we perform thermal stability tests of these hyperdoped passivating contacts and show that under certain laser conditions, the B-doped samples exhibit good thermal stability with near full activation for temperatures up to 800°C. Lastly, we transfer this technique to a larger area by overlapping laser spots and show uniform passivation quality and electrical performance. We are currently implementing this PLM annealed p-type passivating contacts into double-side back-junction poly-Si/SiOx passivating contact devices. Our results show that PLM can not only enable the next generation of high-efficiency c-Si photovoltaics technology but can also benefit the c-Si integrated circuit industry through hyperdoping other semiconductors with atoms that may otherwise have a low solubility.

doping diffusion profile↗
DOE OSTI2026

Leveraging Stereochemistry to Optimize the Properties of Polyhydroxyalkanoates

The recycling of low-density polyethylene (LDPE) is challenging due to difficulties with sorting and contamination, leading to environmental harm. Polyhydroxyalkanoates (PHAs) are at the forefront of high-performance biodegradable alternatives to olefinic plastics, but few offer LDPE-like properties such as low strength and crystallinity while maintaining high ductility and thermal stability. Herein, we report a series of isoenriched transpoly( 3-hydroxy-2-methylbutyrates) (trans-PHMBs) with tunable mechanical and thermal properties. These polymers were synthesized through ring-opening polymerization of racemic trans-3,4-dimethylpropiolactone (rac-trans-DMPL), sourced from C1 and C4 feedstocks, using a new class of “sandwich” C 2 symmetric rac-( Ar BDI*)ZnO i Pr catalysts (where BDI = β-diketiminate). Variation of aromatic groups (Ar) and polymerization temperature yielded mm%s between 45−79% and melting temperatures (T m ) between 141−174 °C. trans-PHMB with intermediate isotacticities of 73 and 75 mm% exhibit similar stress−strain profiles to LDPE, indicating that these polymers have the potential to serve as higher melting, degradable substitutes for LDPE.

Biopolymers↗
DOE OSTI2023

X-Ray Scattering Data Processing and Analysis

Semicrystalline polymers have a degree of crystallinity that depends on chain structure and crystallization conditions. Thermomechanical properties are influenced by the degree of crystallinity and crystalline morphology. A common method used to understand crystalline content, crystal and amorphous layer thickness, and layer thickness distributions, is X-ray scattering (XS). This report uses XS to first investigate crystalline orientation in high density polyethylene (HDPE) samples. Then, a single orientation is analyzed via XS in a temperature study to investigate crystalline behavior under changing temperatures. Lastly, block copolymer filaments extruded at varying speeds are analyzed. The X-ray data are used to gain a baseline understanding of crystalline behavior in these unique filaments.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Influence of Single-Crystalline Morphology on the Electrochemical Behavior of High-Nickel Layered Oxide Cathodes

High-Nickel layered oxides are being pursued for their high specific capacities. With increasing nickel content, the layered oxides also suffer from structural and morphological instabilities, which degrade the electrochemical performance. Single-crystalline morphology presents an attractive solution to these problems, simultaneously reducing surface area available for parasitic reactions and preventing electrolyte penetration into the bulk with the removal of grain boundaries. Single-crystal cathodes have already shown promising results with NMC composition cathodes, but there are still gaps in the fundamental understanding of how single-crystalline morphology alters electrochemical behavior. We attempt to fill some of these gaps by studying in detail the electrochemical operation of polycrystalline and single-crystalline LiNiO 2 (LNO). Single-crystal LNO is prepared through a molten salt method yielding high-quality, distinct crystals with comparable lattice chemistry to polycrystalline LNO. The single-crystal LNO achieves far greater stability during long-term cycling, reaching 500 cycles with 82.5% capacity retention. Interestingly, the single-crystalline LNO also displays superior rate performance, delivering 157 mA h g −1 at 10C discharge rate. Investigation of the phase evolution behavior during cycling strongly suggests that the absence of grain boundaries in single-crystalline LNO is responsible for the superior performance.

25 ENERGY STORAGE↗
DOE OSTI2024

Epitaxially Grown Single-Crystalline SrTiO 3 Membranes Using a Solution-Processed, Amorphous SrCa 2 Al 2 O 6 Sacrificial Layer

Water-soluble sacrificial layers based on epitaxially-grown, single crystalline (Ca, Sr, Ba) 3 Al 2 O 6 layer are widely used for creating free-standing perovskite oxide membranes. However, obtaining these sacrificial layers with intricate stoichiometry remains a challenge, especially for molecular beam epitaxy (MBE). In this study, we demonstrate the hybrid MBE growth of epitaxial, single crystalline SrTiO 3 films using a solution processed, amorphous SrCa 2 Al 2 O 6 sacrificial layer onto SrTiO 3 (001) substrates. Prior to the growth, the oxygen plasma exposure was used to first create the crystalline SrCa 2 Al 2 O 6 layer with well-defined surface crystallinity. Utilizing reflection high energy electron diffraction, x-ray diffraction, and atomic force microscopy, we observe an atomic layer-by-layer growth of epitaxial, single crystalline SrTiO 3 film on the SrCa 2 Al 2 O 6 layer with atomically smooth surfaces. The SrCa 2 Al 2 O6 layer was subsequently dissolved in de-ionized water to create free-standing SrTiO3 membranes that were transferred onto a metal-coated Si wafer. Membranes created with Sr-deficiency revealed ferroelectric-like behavior measured using piezo force microscopy whereas stoichiometric films remained paraelectric-like. Furthermore, these findings underscore the viability of using ex-situ deposited amorphous SrCa2Al2O6 for epitaxial, single crystalline growth, as well as the importance of point defects in determining the ferroic properties in membranes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

High-Entropy Borides under Extreme Environment of Pressures and Temperatures

The high-entropy transition metal borides containing a random distribution of five or more constituent metallic elements offer novel opportunities in designing materials that show crystalline phase stability, high strength, and thermal oxidation resistance under extreme conditions. We present a comprehensive theoretical and experimental investigation of prototypical high-entropy boride (HEB) materials such as (Hf, Mo, Nb, Ta, Ti)B2 and (Hf, Mo, Nb, Ta, Zr)B2 under extreme environments of pressures and temperatures. The theoretical tools include modeling elastic properties by special quasi-random structures that predict a bulk modulus of 288 GPa and a shear modulus of 215 GPa at ambient conditions. HEB samples were synthesized under high pressures and high temperatures and studied to 9.5 GPa and 2273 K in a large-volume pressure cell. The thermal equation of state measurement yielded a bulk modulus of 276 GPa, in excellent agreement with theory. The measured compressive yield strength by radial X-ray diffraction technique in a diamond anvil cell was 28 GPa at a pressure of 65 GPa, which is a significant fraction of the shear modulus at high pressures. The high compressive strength and phase stability of this material under high pressures and high temperatures make it an ideal candidate for application as a structural material in nuclear and aerospace fields.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Molecular models for creep in oriented polyethylene fibers

Highly oriented and crystalline polyetheylene (PE) fibers have a large failure stress under rapid tensile loading but exhibit significant creep at much smaller stresses that limits applications. A possible mechanism is slip of chains due to stress-enhanced, thermally activated nucleation of dislocations at chain ends in crystalline regions. Molecular dynamics simulations are used to parameterize a Frenkel–Kontorova model that provides analytic expressions for the limiting stress and activation energy for dislocation nucleation as a function of stress. Results from four commonly used hydrocarbon potentials are compared to show that the qualitative behavior is robust and estimate quantitative uncertainties. In all cases, the results can be described by an Eyring model with values of the zero-stress activation energy Ea0≈1.5 eV and activation volume V* ≈ 45 Å3 that are consistent with the experimental results for increasingly crystalline materials. The limiting yield stress is ∼8 GPa. These results suggest that activated dislocation nucleation at chain ends is an important mechanism for creep in highly oriented PE fibers.

O’Connor, Thomas C. (ORCID:0000000293930295)↗
DOE OSTI2023

Achieving High Permittivity Paraelectric Behavior in Mesogen-Free Sulfonylated Chiral Polyethers with Smectic C Liquid Crystalline Self-Assembly

Ferroelectric liquid crystalline polymers (LCPs) with a high spontaneous polarization (P s ) are of great interest for the fabrication of advanced electronic devices. However, conventional ferroelectric LCPs typically exhibit low spontaneous polarization, only around 1 mC/m 2 . To increase the orientational polarization for ferroelectric LCPs, in this work, we designed mesogen-free comb-shaped LCPs based on isotactic polyepichlorohydrin, which contained highly dipolar sulfonyl groups (dipole moment of 4.5 Debye) in the side chains. The goal was to increase dipole density and induce ferroelectric switching. In this new series of mesogen-free LCPs, the sulfonyl groups were first moved away from the main chain to mitigate strong dipole–dipole interactions. Second, methyl-branched alkyl side chains were implemented to decrease the crystallizability and induce the Smectic C (SmC) self-assembly. Intriguingly, these SmC samples, for the first time, exhibited typical paraelectric behavior (i.e., slim S-shaped single hysteresis loops) with a high dielectric constant in the range of 20–30. Finally, learning from the knowledge obtained from this study, we will be able to design new mesogen-free LCPs with tailor-made dipole–dipole interactions and realize ferroelectricity.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Peptoid-Based Programmable 2D Nanomaterial Sensor for Selective and Sensitive Detection of H 2 S in Live Cells

During the past decades, a variety of two-dimensional (2D) nanosheets have been developed through supramolecular self-assembly. Among them, those assembled from sequence-defined molecules have received particularly attention because they enable a precise displaying of functional groups, including fluorescent dyes, within nanosheet surfaces. On the other hand, due to the fluorescence self-quenching, synthesis of organic 2D nanosheets exhibiting high fluorescence quantum yields is a significant challenge. Herein, we report the utilization of H 2 S-responsive probes as peptoid sidechains to design and synthesize crystalline 2D nanomembranes (2DNMs) as selective and sensitive H 2 S sensors. These 2DNM sensors exhibit a high quantum yield as a result of high crystallinity and tunable probe density. Compared with amorphous state of peptoid assembly and pre-assembled peptoid-probe conjugates, these crystalline 2DNM sensors exhibit a significantly strong fluorescence intensity and a high sensitivity (~ 0.36 nM). By sonication-cutting these 2DNM sensors into a colloidal form in aqueous solution, we further demonstrated the use of colloidal 2DNMs for detecting both exogenous and endogenous H 2 S inside cells or targeted cell organelles. As far as we know, this is the first example of using sequence-defined 2D nanomaterials for selective and sensitive detection of H 2 S. Because peptoids are biocompatible and peptoid-based 2DNMs are highly programmable, we expect that this new class of 2DNM sensors offer great potentials for detecting H 2 S and for biological applications.

2D nanomaterials↗
DOE OSTI2024

Compositional zoning of the Otowi Member of the Bandelier Tuff, Valles caldera, New Mexico, USA

The Otowi Member of the Bandelier Tuff erupted at ca. 1.60 Ma from the Valles caldera (New Mexico, USA). It consists of as much as 400 km 3 (dense rock equivalent) of strongly differentiated high-silica rhyolite and shows systematic upward variations in crystallinity, mineral chemistry, and trace element concentrations through its thickness, but the major element composition is almost constant and is near the low-pressure granite minimum. Incompatible trace elements in whole pumice fragments and glasses show well-correlated linear covariations. Upward zoning to lower abundances of incompatible trace elements is accompanied by development of overgrowths on quartz and alkali feldspar, although earlier-formed interiors of quartz and feldspar have near-constant compositions throughout the tuff, modified by cation diffusion in the case of feldspar. Melt inclusions in remnant quartz cores show diverse Pb isotope ratios, pointing to a wide range of distinct protoliths that contributed rhyolitic melt to the Otowi magma. Mineral thermometers suggest a modest temperature gradient through the melt body, perhaps of 40 °C, at the time of eruption. Chemical, textural, and mineralogical variations and volume-composition relations through the tuff are consistent with an origin for zoning by melting of a high-crystallinity cumulate layer beneath cognate supernatant liquid to produce denser, remobilized liquid of accumulative composition (i.e., the “modified mush model”). Melting may have occurred in several episodes. The latest of these episodes, probably thousands of years prior to eruption, introduced new rhyolitic liquid into the system and was associated with a thermal excursion, recorded in core compositions of pyroxene, during which much of the earlier crystal mass was dissolved. This left inherited cores and interiors of accumulated quartz and feldspar mantled with new growth having less-evolved compositions (higher Ti, Sr, and Ba). Changing solubility of zircon during cumulate melting produced a reversal of Zr concentrations. There is no clear petrologic evidence of a recharge eruption trigger; nonetheless, compositional zoning resulted mainly from repeated recharge-induced remobilization of quartz-feldspar cumulate. The Otowi system was built, evolved, and modified by several events over the course of a few hundred thousand years.

Wolff, J. A.↗