Search NASA⌕ Search

SEARCH · Search NASA

Results for “initial data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Statistical design study of lunar ceramic

Fabrication of a lunar ceramic was conducted according to a statistically designed experiment. The method of cold pressing was used since the consumption of electrical energy is kept to a minimum (a priority in the lunar environment). This traditional fabrication technique also provides an initial data source on which further investigations can be based. Results obtained from using two percent binder, a cold pressing pressure of 276 MPa, and 24 hours sintering time yielded the greatest compressive strength of 247 MPa. Analysis of each variable's influence on the compressive strength is also presented.

Effinger, Mike↗
NASA NTRS1994

A New Tribological Test for Candidate Brush Seal Materials Evaluation

A new tribological test for candidate brush seal materials evaluation has been developed. The sliding contact between the brush seal wires and their mating counterface journal is simulated by testing a small tuft of wire against the outside diameter of a high speed rotating shaft. The test configuration is similar to a standard block on ring geometry. The new tester provides the capability to measure both the friction and wear of candidate wire and counterface materials under controlled loading conditions in the gram to kilogram range. A wide test condition latitude of speeds (1 to 27 m/s), temperatures (25 to 700 C), and loads (0.5 to 10 N) enables the simulation of many of the important tribological parameters found in turbine engine brush seals. This paper describes the new test rig and specimen configuration and presents initial data for candidate seal materials comparing tuft test results and wear surface morphology to field tested seal components.

Fellenstein, James A.↗
NASA NTRS1995

A well-posed numerical method to track isolated conformal map singularities in Hele-Shaw flow

We present a new numerical method for calculating an evolving 2D Hele-Shaw interface when surface tension effects are neglected. In the case where the flow is directed from the less viscous fluid into the more viscous fluid, the motion of the interface is ill-posed; small deviations in the initial condition will produce significant changes in the ensuing motion. This situation is disastrous for numerical computation, as small round-off errors can quickly lead to large inaccuracies in the computed solution. Our method of computation is most easily formulated using a conformal map from the fluid domain into a unit disk. The method relies on analytically continuing the initial data and equations of motion into the region exterior to the disk, where the evolution problem becomes well-posed. The equations are then numerically solved in the extended domain. The presence of singularities in the conformal map outside of the disk introduces specific structures along the fluid interface. Our method can explicitly track the location of isolated pole and branch point singularities, allowing us to draw connections between the development of interfacial patterns and the motion of singularities as they approach the unit disk. In particular, we are able to relate physical features such as finger shape, side-branch formation, and competition between fingers to the nature and location of the singularities. The usefulness of this method in studying the formation of topological singularities (self-intersections of the interface) is also pointed out.

Baker, Gregory↗
NASA NTRS1995

Testing higher-order Lagrangian perturbation theory against numerical simulations. 2: Hierarchical models

We present results showing an improvement of the accuracy of perturbation theory as applied to cosmological structure formation for a useful range of scales. The Lagrangian theory of gravitational instability of Friedmann-Lemaitre cosmogonies is compared with numerical simulations. We study the dynamics of hierarchical models as a second step. In the first step we analyzed the performance of the Lagrangian schemes for pancake models, the difference being that in the latter models the initial power spectrum is truncated. This work probed the quasi-linear and weakly non-linear regimes. We here explore whether the results found for pancake models carry over to hierarchical models which are evolved deeply into the non-linear regime. We smooth the initial data by using a variety of filter types and filter scales in order to determine the optimal performance of the analytical models, as has been done for the 'Zel'dovich-approximation' - hereafter TZA - in previous work. We find that for spectra with negative power-index the second-order scheme performs considerably better than TZA in terms of statistics which probe the dynamics, and slightly better in terms of low-order statistics like the power-spectrum. However, in contrast to the results found for pancake models, where the higher-order schemes get worse than TZA at late non-linear stages and on small scales, we here find that the second-order model is as robust as TZA, retaining the improvement at later stages and on smaller scales. In view of these results we expect that the second-order truncated Lagrangian model is especially useful for the modelling of standard dark matter models such as Hot-, Cold-, and Mixed-Dark-Matter.

Melott, A. L.↗
NASA NTRS1994

Global Asymptotic Behavior of Iterative Implicit Schemes

The global asymptotic nonlinear behavior of some standard iterative procedures in solving nonlinear systems of algebraic equations arising from four implicit linear multistep methods (LMMs) in discretizing three models of 2 x 2 systems of first-order autonomous nonlinear ordinary differential equations (ODEs) is analyzed using the theory of dynamical systems. The iterative procedures include simple iteration and full and modified Newton iterations. The results are compared with standard Runge-Kutta explicit methods, a noniterative implicit procedure, and the Newton method of solving the steady part of the ODEs. Studies showed that aside from exhibiting spurious asymptotes, all of the four implicit LMMs can change the type and stability of the steady states of the differential equations (DEs). They also exhibit a drastic distortion but less shrinkage of the basin of attraction of the true solution than standard nonLMM explicit methods. The simple iteration procedure exhibits behavior which is similar to standard nonLMM explicit methods except that spurious steady-state numerical solutions cannot occur. The numerical basins of attraction of the noniterative implicit procedure mimic more closely the basins of attraction of the DEs and are more efficient than the three iterative implicit procedures for the four implicit LMMs. Contrary to popular belief, the initial data using the Newton method of solving the steady part of the DEs may not have to be close to the exact steady state for convergence. These results can be used as an explanation for possible causes and cures of slow convergence and nonconvergence of steady-state numerical solutions when using an implicit LMM time-dependent approach in computational fluid dynamics.

Yee, H. C.↗
NASA NTRS1999

Polar Magnetic Field Experiment

This grant covers the initial data reduction and analysis of the magnetic field measurements of the Polar spacecraft. At this writing data for the first three years of the mission have been processed and deposited in the key parameter database. These data are also available in a variety of time resolutions and coordinate systems via a webserver at UCLA that provides both plots and digital data. The flight software has twice been reprogrammed: once to remove a glitch in the data where there were rare collisions between commands in the central processing unit and once to provide burst mode data at 100 samples per second on a regular basis. The instrument continues to function as described in the instrument paper (1.1 in the bibliography attached below). The early observations were compared with observations on the same field lines at lower altitude. The polar magnetic measurements also proved to be most useful for testing the accuracy of MHD models. WE also made important contributions to study of waves and turbulence.

Russell, C. T.↗
NASA NTRS1999

Affordable Precursor Flight Experiment for Ultra Lightweight Mirror Technologies

As a follow-on to the spectacular success of the Hubble Space Telescope (HST), NASA is currently conducting pre-phase A studies of an even larger aperture telescope, called NGST (Next Generation Space Telescope), that will continue the phenomenal flow of astrophysical discoveries well into the next millennium. Because of the very large aperture required, current NGST concepts have been driven to elaborate schemes of foldable ultra thin and ultra light mirror segment systems that can be deployed on orbit. Due to the complexity of these optical systems, it is imperative that adequate demonstration experiments be flown to verify these new technology concepts before committing to the final design and implementation of the NGST. This paper presents a proposal for a very simple, inexpensive Hitchhiker flight experiment that will determine gravity release effects on very thin mirror segments made from current competitive materials. These experiments will provide the initial data that will be needed before more extensive demonstration flights of the NGST system can be flown.

Guffin, Orville T.↗
NASA NTRS1999

Implications of the Improved Understanding of the Gravitational and Topography Fields

The Mars Orbiter Laser Altimeter (MOLA) has been successfully mapping the shape and topography of Mars on an intermittent basis since the Mars Global Surveyor (MGS) spacecraft arrived at Mars in Sept. 1997. In early April, MGS reached it's mapping orbit and began the mapping phase of the mission. Since that time MOLA has been operating continuously. MOLA is a laser altimeter with a pulse rate of 10 Hz and a precision of about 30 to 40 cm over flat surfaces. The laser pulses are approximately 330 meters apart on the surface of Mars and each pulse illuminates an area approximately 150 meters in diameter. The orbital accuracy of MGS is a few meters in the radial direction enabling the topography to be interpreted at the few meter accuracy level. The initial data have provided a new geodetic description of the size and shape of Mars, including accurate estimates for the equatorial and polar radii, and the planetary flattening. The data have revealed the northern hemisphere to be very low in elevation, very flat, and almost devoid of craters. The north polar icecap lies in a basin about 5 km below the average altitude and reaches to a height of 3 km. The heavily cratered southern hemisphere is high and the terrain is rough. The south polar icecap is about 5 km above the average planetary altitude and 2 km above the surrounding terrain. The MOLA profile data show the gradual but steady increase in altitude of the surface of Mars from the north pole to the south pole. This is a consistent feature for all north-south profiles and reflects the 3 km separation of the center of figure for Mars from the center of mass along the rotation axis.

Smith, David E.↗
NASA NTRS1999

The Effects of Partial Mechanical Loading and Ibandronate on Skeletal Tissues in the Adult Rat Hindquarter Suspension Model for Microgravity

We report initial data from a suspended rat model that quantitatively relates chronic partial weightbearing to bone loss. Chronic partial weightbearing is our simulation of the effect of limited artificial gravity aboard spacecraft or reduced planetary gravity. Preliminary analysis of bone by PQCT, histomorphometry, mechanical testing and biochemistry suggest that chronic exposure to half of Earth gravity is insufficient to prevent severe bone loss. The effect of episodic full weightbearing activity (Earth Gravity) on rats otherwise at 50% weightbearing was also explored. This has similarity to treatment by an Earth G-rated centrifuge on a spacecraft that normally maintained artificial gravity at half of Earth G. Our preliminary evidence, using the above techniques to analyze bone, indicate that 2 hours daily of full weightbearing was insufficient to prevent the bone loss observed in 50% weightbearing animals. The effectiveness of partial weightbearing and episodic full weightbearing as potential countermeasures to bone loss in spaceflight was compared with treatment by ibandronate. Ibandronate, a long-acting potent bisphosphonate proved more effective in preventing bone loss and associated functionality based upon structure than our first efforts at mechanical countermeasures. The effectiveness of ibandronate was notable by each of the testing methods we used to study bone from gross structure and strength to tissue and biochemistry. These results appear to be independent of generalized systemic stress imposed by the suspension paradigm. Preliminary evidence does not suggest that blood levels of vitamin D were affected by our countermeasures. Despite the modest theraputic benefit of mechanical countermeasures of partial weightbearing and episodic full weightbearing, we know that some appropriate mechanical signal maintains bone mass in Earth gravity. Moreover, the only mechanism that correctly assigns bone mass and strength to oppose regionally specific force applied to bone is mechanical, a process based upon bone strain. Substantial evidence indicates that the specifics of dynamic loading i.e. time-varying forces are critical. Bone strain history is a predictor of the effect that mechanical conditions have on bone structure mass and strength. Using servo-controlled force plates on suspended rats with implanted strain gauges we manipulated impact forces of ambulation in the frequency (Fourier) domain. Our results indicate that high frequency components of impact forces are particularly potent in producing bone strain independent of the magnitude of the peak force or peak energy applied to the leg. Because a servo-system responds to forces produced by the rat's own muscle activity during ambulation, the direction of ground-reaction loads act on bone through the rat's own musculature. This is in distinction to passive vibration of the floor where forces reach bone through the natural filters of soft tissue and joints. Passive vibration may also be effective, but it may or may not increase bone in the appropriate architectural pattern to oppose the forces of normal ambulatory activity. Effectiveness of high frequency mechanical stimulation in producing regional (muscle directed) bone response will be limited by 1. the sensitivity of bone to a particular range of frequencies and 2. the inertia of the muscles, limiting their response to external forces by increasing tension along insertions. We have begun mathematical modeling of normal ambulatory activity. Effectiveness of high frequency mechanical stimulation in producing regional (muscle directed) bone response will be limited by 1. the sensitivity of bone to a particular range of frequencies and 2. the inertia of the muscles, limiting their response to external forces by increasing tension along insertions. We have begun mathematical modeling of the rat forelimb as a transfer function between impact force and bone strain to predict optimal dynamic loading conditions for this system. We plan additional studies of mechanical counter-measures that incorporate improved dynamic loading, features relevant to anticipated evaluation of artificial gravity, exercise regimens and exposure to Martian gravity, The combination of mechanical countermeasures with ibandronate will also be investigated for signs of synergy.

Schultheis, Lester W.↗
NASA NTRS2001

Investigation of Nitride Morphology After Self-Aligned Contact Etch

Self-Aligned Contact (SAC) etch has emerged as a key enabling technology for the fabrication of very large-scale memory devices. However, this is also a very challenging technology to implement from an etch viewpoint. The issues that arise range from poor oxide etch selectivity to nitride to problems with post etch nitride surface morphology. Unfortunately, the mechanisms that drive nitride loss and surface behavior remain poorly understood. Using a simple langmuir site balance model, SAC nitride etch simulations have been performed and compared to actual etched results. This approach permits the study of various etch mechanisms that may play a role in determining nitride loss and surface morphology. Particle trajectories and fluxes are computed using Monte-Carlo techniques and initial data obtained from double Langmuir probe measurements. Etched surface advancement is implemented using a shock tracking algorithm. Sticking coefficients and etch yields are adjusted to obtain the best agreement between actual etched results and simulated profiles.

Hwang, Helen H.↗
NASA NTRS1994

On the Dynamics of Computing a Chemically Relaxed Nonequilibrium Flow

In order to gain insights into the strong dependence of numerical solutions on initial data for finite time steps, a set of nonlinear test problems rich enough to capture the behavior of difference schemes were recently identified and the numerical basins of attraction for these problems were computed using commonly used time discretizations in CFD. Our study revealed a wealth of surprisingly nonlinear behavior of numerical schemes that were not observed before, in particular for the implicit time discretizations that are commonly used in CFD. The goal of this work is to apply these tools to study a practical model from non-equilibrium flowfield relaxation. This type of problem arises in chemically nonequilibrium hypersonic flows such as in a shock tube experiment or an expanding nozzle. Here we consider a reacting mixture of (N2, N) for an inviscid one-dimensional steady model. Preliminary numerical results indicate that, aside from the possibility of spurious numerical solutions being introduced by the time discretizations, limitations on the model for physical or accurate solutions may also play a part in the dynamics observed.

Sweby, P. K.↗
NASA NTRS2001

The Cloud Physics Lidar: Instrument Description and Initial Measurement Results

The new Cloud Physics Lidar (CPL) has been built for use on the NASA ER-2 high altitude aircraft. The purpose of the CPL is to provide multi-wavelength measurements of cirrus, subvisual cirrus, and aerosols with high temporal and spatial resolution. The CPL utilizes state-of-the-art technology with a high repetition rate, a low pulse energy laser, and photon-counting detection. The first deployment for the CPL was the SAFARI-2000 field campaign during August-September 2000. We provide here an overview of the instrument and initial data results to illustrate the measurement capability of the CPL.

McGill, Matthew↗
NASA NTRS1995

On the Dynamics of Implicit Linear Multistep Methods

Some new guidelines on the usage of implicit linear multistep methods (LMMs) as time-dependent approaches for obtaining steady-state numerical solutions in computational fluid dynamics (CFD) are explored. The commonly used implicit LMMs in CFD belong to the class of superstable time discretizations. It can be shown that the nonlinear asymptotic behavior in terms of bifurcation diagrams and basins of attractions of these schemes can provide an improved range of initial data and time step over the linearized stability limit.

Yee, H. C.↗
NASA NTRS2001

Microshutter Arrays for the NGST NIRSpec

We are developing a programmable multiobject field selector for the NGST NIRSpec. This device is a microshutter array, a close-packed 2000 x 2000 array of 100 micrometer x 100 micrometer shutters fabricated with Micro-ElectroMechanical Systems (MEMS) technologies. The shutters are opened using a magnet scanned over the array. The shutters are held open by electrostatic potentials on adjacent vertical electrodes. Modeling of the magnetic actuation of the microshutters allowed optimization of the magnetic field configuration, the distance between magnet and shutters, and the force and torque produced by the magnet. The results of laboratory tests are consistent with our modeling. We have demonstrated actuation, latching and addressing. We are able to rotate shutters out of the plane up to 90 degree and more, to latch them electrostatically to the walls and release them selectively. During the last six month all critical elements of the array have been demonstrated. Fabrication processes were developed to deposit vertical electrodes on support grid side walls and insulated light-shields that block the gaps between shutters and the support grid. Physical optics analysis was performed to assess the expected optical performance of the microshutters. A preliminary Fourier optics analysis on the microshutter array performance has been carried out. More detailed analysis of wave propagation through 3D structures is a next step. An optical test station for verifying optical parameters of the shutter array at room temperature has been developed. It allows to measure parameters, such as transmission, scattering, contrast ratio, and diffraction of the array structure. Initial data have been acquired and are being analyzed and compared to theoretical predictions.

Moseley, Harvey↗
NASA NTRS2002

Cloud Physics Lidar: Instrument Description and Initial Measurement Results

The Cloud Physics Lidar (CPL) is a new custom-built instrument for the NASA ER-2 high-altitude aircraft. The CPL can provide multiwavelength measurements of cirrus, subvisual cirrus, and aerosols with high temporal and spatial resolution. Its state-of-the-art technology gives it a high repetition rate, and photon-counting detection, and includes a low-pulse-energy laser. The CPL was first deployed at the Southern African Regional Science Initiative's 2000 field campaign during August and September 2000. This paper provides an overview of the instrument and initial data results to illustrate the measurement capability of the CPL.

McGill, Matthew↗
NASA NTRS2003

ICESat Observations of Southern Alaska Glaciers

In late February and March, 2003, the Ice, Cloud, and land Elevation Satellite (ICESat) measured ice and land elevations along profiles across southern Alaska. During this initial data acquisition stage ICESat observations were made on 8-day repeat tracks to enable calibration and validation of the ICESat data products. Each profile consists of a series of single point values derived from centroid elevations of an $\approx$70 m diameter laser footprint. The points are s4pakated by $\approx$172 m along track. Data siets of 8-day observations (an ascending and descending ground track) crossed the Bering and Malaspina Glacier. Following its 1993--1995 surge; the Bering Glacier has undergone major terminus retreat as well as ike thinning in the abtation zone. During the later part of the 20th century, parts of the Malaspina thinned by about 1 m/yr. The multiple observation profiles across the Bering and Malaspina piedmont lobes obtained in February/March are being geolocated on Landsat images and the elevation profiles will be used for a number o scientific objectives. Based on our simulations of ICESat performance over the varied ice surface of the Jakobshavn Glacier of GReenland, 2003, we expect to measure annual, and possibly seasonal, ice elevation changes on the large Alaskan glaciers. Using elevation data obtained from a second laser, we plan to estimate ice elevation changes on the Bering Glacier between March and October 2003.

Sauber, Jeanne↗
NASA NTRS2004

Evolving a Puncture Black Hole with Fixed Mesh Refinement

We present a detailed study of the effects of mesh refinement boundaries on the convergence and stability of simulations of black hole spacetimes. We find no technical problems. In our applications of this technique to the evolution of puncture initial data, we demonstrate that it is possible to simulaneously maintain second order convergence near the puncture and extend the outer boundary beyond 100M, thereby approaching the asymptotically flat region in which boundary condition problems are less difficult.

Imbiriba, Breno↗
NASA NTRS2004

High Order And High Resolution Methods For a Model CAA Problem

The initial value problem for the first order linear wave equation in one space dimension is treated for two cases with specified initial data and grid, and data from solutions at t = 400 and t = 800 are presented, as prescribed for Problem 1 in Category 1. Results are shown from computations with a sequence of recently developed high order and high resolution methods which combine Hermite interpolation, Cauchy-Kowaleskya recursion for time derivatives, and Taylor series time advancement. These methods have the same order of accuracy in time as in space. Results are shown from methods that range from third to nineteenth order. The stated problems with the prescribed coarse grid can be simulated with errors that are at the level of machine accuracy if the method is sufficiently high order. In addition, the growth of the maximum absolute error out to t = 100,000 is given for simulations with the stated problem data.

Goodrich, John W.↗