SEARCH · Search NASA

Results for “interface failure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 289 records · Page 16

All sources NASA NTRS DOE OSTI

DOE OSTI2018

Multi-scale computational analysis of unidirectional carbon fiber reinforced polymer composites under various loading conditions

In this study, a multi-scale computational analysis based on representative volume element (RVE) modeling and molecular dynamics (MD) simulations is developed to investigate the microscopic failure mechanisms of unidirectional (UD) carbon fiber reinforced polymer (CFRP) composites. The average properties of the 200-nm thickness interphase region between fiber and matrix are characterized through MD simulations and an analytical gradient model. The results demonstrate that the interphase region has higher Young’s modulus and strength, compared to the bulk matrix. This stiffened interphase region influences the composite response significantly. Specifically, the traditional two-phase model with zero-thickness interface fails to capture the stress-strain behavior compared to the experimental data. However, by adding the interphase region to a modified RVE model, the accuracy of simulation results will be improved significantly. Furthermore, a coupled experimental-computational micromechanics approach is adopted to calibrate and validate the cohesive parameters of the interface. By including the cohesive interface, our modified RVE model accurately captures the failure strength of the composites. Finally, different failure mechanisms for specimens are investigated using our multi-scale computational framework. In conclusion, the results show that the failure modes of UD CFRP composites are very complex and multiple failure mechanisms co-exist depending on the loading conditions, agreeing well with our experimental analyses.

36 MATERIALS SCIENCE↗

NASA NTRS1989

Local-global analysis of crack growth in continuously reinfoced ceramic matrix composites

This paper describes the development of a mathematical model for predicting the strength and micromechanical failure characteristics of continuously reinforced ceramic matrix composites. The local-global analysis models the vicinity of a propagating crack tip as a local heterogeneous region (LHR) consisting of spring-like representation of the matrix, fibers and interfaces. Parametric studies are conducted to investigate the effects of LHR size, component properties, and interface conditions on the strength and sequence of the failure processes in the unidirectional composite system.

Ballarini, Roberto↗

DOE OSTI2018

In Situ SEM Observations of Fracture Behavior of Laser Welded–Brazed Al/Steel Dissimilar Joint

Laser welding–brazing of 6061-T6 aluminum alloy to DP590 dual-phase steel with Al-Si12 flux-cored filler wire was performed. The microstructure at the brazing interface was characterized. Fracture behavior was observed and analyzed by in situ scanning electron microscope. The microstructure of the brazing interface showed that inhomogeneous intermetallic compounds formed along the thickness direction, which had a great influence on the crack initiation and propagation. In the top region, the reaction layer at the interface consisted of scattered needle-like Fe(Al,Si){sub 3} and serration-shaped Fe{sub 1.8}Al{sub 7.2}Si. In the middle region, the compound at the interface was only serration-shaped Fe{sub 1.8}Al{sub 7.2}Si. In the bottom region, the interface was composed of lamellar-shaped Fe{sub 1.8}Al{sub 7.2}Si. The cracks were first detected in the bottom region and propagated from bottom to top along the interface. At the bottom region, the crack initiated and propagated along the Fe{sub 1.8}Al{sub 7.2}Si/weld seam interface during the in situ tensile test. When the crack propagated into the middle region, a deflection of crack propagation appeared. The crack first propagated along the steel/Fe{sub 1.8}Al{sub 7.2}Si interface and then moved along the weld seam until the failure of the joint. The tensile strength of the joint was 146.5 MPa. Some micro-cracks were detected at Fe(Al,Si){sub 3} and the interface between the steel substrate and Fe(Al,Si){sub 3} in the top region while the interface was still connected.

36 MATERIALS SCIENCE↗

NASA NTRS1992

Advanced techniques in reliability model representation and solution

The current tendency of flight control system designs is towards increased integration of applications and increased distribution of computational elements. The reliability analysis of such systems is difficult because subsystem interactions are increasingly interdependent. Researchers at NASA Langley Research Center have been working for several years to extend the capability of Markov modeling techniques to address these problems. This effort has been focused in the areas of increased model abstraction and increased computational capability. The reliability model generator (RMG) is a software tool that uses as input a graphical object-oriented block diagram of the system. RMG uses a failure-effects algorithm to produce the reliability model from the graphical description. The ASSURE software tool is a parallel processing program that uses the semi-Markov unreliability range evaluator (SURE) solution technique and the abstract semi-Markov specification interface to the SURE tool (ASSIST) modeling language. A failure modes-effects simulation is used by ASSURE. These tools were used to analyze a significant portion of a complex flight control system. The successful combination of the power of graphical representation, automated model generation, and parallel computation leads to the conclusion that distributed fault-tolerant system architectures can now be analyzed.

Palumbo, Daniel L.↗

NASA NTRS1994

Intelligent command and control systems for satellite ground operations

The Georgia Tech portion of the Intelligent Control Center project includes several complementary activities. Two major activities entail thesis level research; the other activities are either support activities or preliminary explorations (e.g., task analyses) to support the research. The first research activity is the development of principles for the design of active interfaces to support monitoring during real-time supports. It is well known that as the operator's task becomes less active, i.e., more monitoring and less active control, there is concern that the operator will be less involved and less able to rapidly identify anomalous or failure situations. The research project to design active monitoring interfaces is an attempt to remediate this undesirable side-effect of increasingly automated control systems that still depend ultimately on operator supervision. The second research activity is the exploration of the use of case-based reasoning as a way to accumulate operator experience and make it available in computational form.

Mitchell, Christine M.↗

NASA NTRS2002

Intralaminar and Interlaminar Progressive Failure Analysis of Composite Panels with Circular Cutouts

A progressive failure methodology is developed and demonstrated to simulate the initiation and material degradation of a laminated panel due to intralaminar and interlaminar failures. Initiation of intralaminar failure can be by a matrix-cracking mode, a fiber-matrix shear mode, and a fiber failure mode. Subsequent material degradation is modeled using damage parameters for each mode to selectively reduce lamina material properties. The interlaminar failure mechanism such as delamination is simulated by positioning interface elements between adjacent sublaminates. A nonlinear constitutive law is postulated for the interface element that accounts for a multi-axial stress criteria to detect the initiation of delamination, a mixed-mode fracture criteria for delamination progression, and a damage parameter to prevent restoration of a previous cohesive state. The methodology is validated using experimental data available in the literature on the response and failure of quasi-isotropic panels with centrally located circular cutouts loaded into the postbuckling regime. Very good agreement between the progressive failure analyses and the experimental results is achieved if the failure analyses includes the interaction of intralaminar and interlaminar failures.

Goyal, Vinay K.↗

NASA NTRS2003

Interface Finite Elements for the Analysis of Fracture Initiation and Progression

Progressive failure analyses (PFA) are important for the prediction of residual strength and damage tolerance of vehicle structures, and to predict the energy absorbing capability of vehicle structures under crash-type loads. Typically continuum damage mechanics (CDM) and fracture mechanics (FM) are the methods used for PFA. The method of interfacial damage mechanics (IDM) is used for PFA in this research. IDM has capabilities intermediate between CDM and FM, and is used to numerically model the initiation, growth, and arrest of cracks. IDM smooths the stress singularity at the crack tip, and is easily adaptable with other nonlinearties such as plasticity and material damage. IDM is implemented by user-defined interface elements in the ABAQUS/ Standard structural analysis software package. The structural components selected to demonstrate the effectiveness PFA using interface elements are, for the most part, those with published test data. These structural components were subjected to quasi-static loading in the tests. Thus, the ABAQUS analyses are used to predict geometrically and materially nonlinear equilibrium states. Impact loading, dynamic fracture, reflected stress waves, inertia, and time dependent material behavior are not considered.

Ambur, Damodar R.↗

NASA NTRS1988

Local-global analysis of crack growth in continuously reinforced ceramic matrix composites

The development is described of a mathematical model for predicting the strength and micromechanical failure characteristics of continuously reinforced ceramic matrix composites. The local-globe analysis models the vicinity of a propagating crack tip as a local heterogeneous region (LHR) consisting of spring like representation of the matrix, fibers and interfaces. This region is embedded in an anisotropic continuum (representing the bulk composite) which is modeled by conventional finite elements. Parametric studies are conducted to investigate the effects of LHR size, component properties, interface conditions, etc. on the strength and sequence of the failure processes in the unidirectional composite system. The results are compared with those predicted by the models developed by Marshall et al. (1985) and by Budiansky et al. (1986).

Ballarini, Roberto↗

NASA NTRS1980

Orbiter subsystem hardware/software interaction analysis. Volume 8: Forward reaction control system

The results of the orbiter hardware/software interaction analysis for the AFT reaction control system are presented. The interaction between hardware failure modes and software are examined in order to identify associated issues and risks. All orbiter subsystems and interfacing program elements which interact with the orbiter computer flight software are analyzed. The failure modes identified in the subsystem/element failure mode and effects analysis are discussed.

Becker, D. D.↗

NASA NTRS2011

SNE Industrial Fieldbus Interface

Programmable logic controllers (PLCs) have very limited diagnostic and no prognostic capabilities, while current smart sensor designs do not have the capability to communicate over Fieldbus networks. The aim is to interface smart sensors with PLCs so that health and status information, such as failure mode identification and measurement tolerance, can be communicated via an industrial Fieldbus such as ControlNet. The SNE Industrial Fieldbus Interface (SIFI) is an embedded device that acts as a communication module in a networked smart sensor. The purpose is to enable a smart sensor to communicate health and status information to other devices, such as PLCs, via an industrial Fieldbus networking protocol. The SNE (Smart Network Element) is attached to a commercial off-the-shelf Any bus-S interface module through the SIFI. Numerous Anybus-S modules are available, each one designed to interface with a specific Fieldbus. Development of the SIFI focused on communications using the ControlNet protocol, but any of the Anybus-S modules can be used. The SIFI communicates with the Any-bus module via a data buffer and mailbox system on the Anybus module, and supplies power to the module. The Anybus module transmits and receives data on the Fieldbus using the proper protocol. The SIFI is intended to be connected to other existing SNE modules in order to monitor the health and status of a transducer. The SIFI can also monitor aspects of its own health using an onboard watchdog timer and voltage monitors. The SIFI also has the hardware to drive a touchscreen LCD (liquid crystal display) unit for manual configuration and status monitoring.

Lucena, Angel↗

DOE OSTI2019

Power Electronics Materials and Bonded Interfaces - Reliability and LIfetime

The emergence of wide-bandgap (WBG) devices in power electronics packages has brought significant attention to the reliability and thermal performance of the bonded interfaces. These interfaces, such as die-attach and substrate-attach, need to withstand the severe stress induced on them by the high-temperature (> 200 degrees C) operation of the WBG devices. Sintered silver and transient liquid phase alloys are key bonded interfaces that can enable the high-temperature operation of WBG devices, however it is essential to evaluate their reliability and study the possible failure mechanisms before they can be used in power electronics packages. Sintered silver is already being adopted in commercial packages as a die-attach, but large-area substrate-attach offers additional reliability challenges. In this project, we investigate the reliability of these interface materials under accelerated thermal cycling and correlate these results with finite element simulations to develop lifetime prediction models. The failure mechanisms of these bonded interfaces are also studied.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2020

Power Electronics Materials and Bonded Interfaces - Reliability and Lifetime

The emergence of wide-bandgap (WBG) devices in power electronics packages has brought significant attention to the reliability and thermal performance of the bonded interfaces. These interfaces, such as die-attach and substrate-attach, need to withstand the severe stress induced on them by the high-temperature (> 200°C) operation of the WBG devices. Sintered silver and transient liquid phase alloys are key bonded interfaces that can enable the high-temperature operation of WBG devices, however it is essential to evaluate their reliability and study the possible failure mechanisms before they can be used in power electronics packages. Sintered silver is already being adopted in commercial packages as a die-attach, but large-area substrate-attach offers additional reliability challenges. In this project, we investigate the reliability of these interface materials under accelerated thermal cycling and correlate these results with finite element simulations to develop lifetime prediction models. The failure mechanisms of these bonded interfaces are also studied.

47 OTHER INSTRUMENTATION↗

NASA NTRS1989

Effect of a high temperature cycle on the mechanical properties of silicon carbide/titanium metal matrix composites

An investigation is conducted of the effects of the SPF/DB cycle on continuous SiC fiber-reinforced Ti-15V-3Cr-3Al-3Sn composite's matrix, fiber, and matrix-fiber interface. The fibers in question, designated SCS-6, have a carbon core and thin, carbon-rich surface. The fatigue endurance limit at 50,000 cycles for the SPF/DB specimens was 50 percent lower than for the as-fabricated material. The substantial changes in tensile strength, fatigue life, and fracture-surface appearance due to the SPF-DB cycle are explained by a difference in the failure mechanisms due to SPF/DB-induced changes in the fiber/matrix interface strength.

Naik, R. A.↗

DOE OSTI2019

Bioinspired nacre-like alumina with a bulk-metallic glass-forming alloy as a compliant phase

Bioinspired ceramics with micron-scale ceramic "bricks" bonded by a metallic "mortar" are projected to result in higher strength and toughness ceramics, but their processing is challenging as metals do not typically wet ceramics. To resolve this issue, we made alumina structures using rapid pressureless infiltration of a zirconium-based bulk-metallic glass mortar that reactively wets the surface of freeze-cast alumina preforms. The mechanical properties of the resulting Al 2 O 3 with a glass-forming compliant-phase change with infiltration temperature and ceramic content, leading to a trade-off between flexural strength (varying from 89 to 800 MPa) and fracture toughness (varying from 4 to more than 9 MPa·m ½ ). The high toughness levels are attributed to brick pull-out and crack deflection along the ceramic/metal interfaces. Since these mechanisms are enabled by interfacial failure rather than failure within the metallic mortar, the potential for optimizing these bioinspired materials for damage tolerance has still not been fully realized.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Performance of hybrid Innegra-carbon fiber composites

Abstract In this work material synergy with high stiffness carbon fiber with ductile high strength polypropylene fiber (Innegra S), (referred to as Innegra, herein) have been evaluated in a range of laminate designs. Both woven and discontinuous carbon fiber have been considered. The discontinuous fibers are based on three-dimensional deposition (3DEP) (referred to as 3DEP, herein) carbon fiber preform process. Eleven (11) variants of Innegra-carbon fiber hybrid laminates were investigated for tensile, flexure, compression, in-plane shear and low velocity impact response. The effect of position of Innegra within the laminate was studied and found to influence strength and stiffness properties. In terms of overall trends, Innegra provides upward of 18% improvement in strain (ductility) to the composite and eliminates brittle fracture of carbon fiber. The moduli trends follow the proportionality of Innegra fiber to carbon fiber plies. However, the strength is controlled by the interface between Innegra and carbon fiber. The primary failure mode in tension and compression is via onset of debonding between Innegra and carbon fiber. The 3DEP carbon fiber constituents provided highest values of in-plane shear indicating that three-dimensional (3D) network of carbon fiber provides higher shear resistance. The Innegra intensive variants exhibited superior energy absorption under low velocity impact, at energy levels 15–60 J. This work provides insight for designers to incorporate Innegra and carbon fiber hybrids in composite structures.

36 MATERIALS SCIENCE↗

NASA NTRS1981

Degradation of a two-layer thermal barrier coating under thermal cycling

A two-layer plasma-sprayed thermal barrier coating on a directionally solidified nickel-base eutectic alloy substrate was characterized prior to and after thermal cycling to 1095 C in an accelerated furnace test. The coating was comprised of an inner layer of Ni-16.4Cr-5.1Al-0.15Y (wt%) bond coat and an outer layer of ZrO2-7.9Y2O3 (wt%) thermal barrier. Characterization of the bond coat revealed that substantial amounts of yttrium and aluminum were oxidized during plasma-spraying in air. The oxidation of these elements reduced the protective capacity of the bond coat so that, on thermal exposure, severe degradation of the bond coat resulted and large amounts of nickel oxide formed. This nickel oxide was demonstrated to grow outward into the thermal barrier, which appears to have increased the stresses in the thermal barrier and contributed to its failure near the thermal barrier-bond coat interface.

Maier, R. D.↗

NASA NTRS1991

Structural characterization of high temperature composites

Glass, ceramic, and carbon matrix composite materials have emerged in recent years with potential properties and temperature resistance which make them attractive for high temperature applications such as gas turbine engines. At the outset of this study, only flexural tests were available to evaluate brittle matrix composites at temperatures in the 600 to 1000 C range. The results are described of an ongoing effort to develop appropriate tensile, compression, and shear test methods for high temperature use. A tensile test for unidirectional composites was developed and used to evaluate the properties and behavior of ceramic fiber reinforced glass and glass-ceramic matrix composites in air at temperatures up to 1000 C. The results indicate generally efficient fiber reinforcement and tolerance to matrix cracking similar to polymer matrix composites. Limiting properties in these materials may be an inherently very low transverse strain to failure, and high temperature embrittlement due to fiber/matrix interface oxidation.

Mandell, J. F.↗

NASA NTRS1991

Alternate cathodes for sodium-metal chloride batteries

Various metal chlorides were tested as possible cathode materials for sodium-metal batteries (in addition to Fe and Ni chlorides, which have been already developed to a stage of commercialization), using an electrochemical cell consisting of a pyrex tube, heated to 250 C, with the metal wire as working electrode, concentric Ni foil as counterelectrode, and high-purity Al as reference electrode. In particular, the aim of this study was to identify metal chlorides insoluble even in neutral melts, possible at the interface during overcharge, in order to eliminate the failure mode of the cell through a cationic exchange of the dissolved metal ions with sodium beta-double-prime alumina solid electrolyte. Results indicate that Mo and Co are likely alternatives to FeCl2 and NiCl2 cathodes in sodium batteries. The open circuit voltages of Na/CoCl(x) and Na/MoCl(x) cells at 250 C would be 2.55 V and 2.64 V, respectively.

Ratnakumar, B. V.↗