SEARCH · Search NASA

Results for “jet in crossflow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

275 records · Page 16

All sources NASA NTRS DOE OSTI

NASA NTRS1986

Natural laminar flow flight experiments on a swept wing business jet-boundary layer stability analyses

The linear boundary layer stability analyses and their correlation with data of 18 cases from a natural laminar flow (NLF) flight test program using a Cessna Citation 3 business jet are described. The transition point varied from 5% to 35% chord for these conditions, and both upper and lower wing surfaces were included. Altitude varied from 10,000 to 43,000 ft and Mach number from 0.3 to 0.8. Four cases were at nonzero sideslip. Although there was much scatter in the results, the analyses of boundary layer stability at the 18 conditions led to the conclusion that crossflow instability was the primary cause of transition. However, the sideslip cases did show some interaction of crossflow and Tollmien-Schlichting disturbances. The lower surface showed much lower Tollmien-Schlichting amplification at transition than the upper surface, but similar crossflow amplifications. No relationship between Mach number and disturbance amplification at transition could be found. The quality of these results is open to question from questionable wing surface quality, inadequate density of transition sensors on the wing upper surface, and an unresolved pressure shift in the wing pressure data. The results of this study show the need for careful preparation for transition experiments. Preparation should include flow analyses of the test surface, boundary layer disturbance amplification analyses, and assurance of adequate surface quality in the test area. The placement of necessary instruments and usefulness of the resulting data could largely be determined during the pretest phase.

Rozendaal, R. A.↗

DOE OSTI2023

Experimental and Computational Investigation of Shaped Film Cooling Holes Designed to Minimize Inlet Separation

Abstract Film cooling is used to protect turbine components from the extreme temperatures by ejecting coolant through arrays of holes to create an air buffer from the hot combustion gases. Limitations in traditional machining meant film cooling holes universally have sharp inlets, which create separation regions at the hole entrance. The present study uses experimental and computational data to show that these inlet separation are a major cause of performance variation in crossflow fed film cooling holes. Three-hole designs were experimentally tested by independently varying the coolant velocity ratio (VR) and the coolant channel velocity ratio (VRc) to isolate the effects of crossflow on hole performance. Leveraging additive manufacturing (AM) technologies, the addition of a 0.25D radius fillet to the inlet of a 7-7-7 shaped hole is shown to significantly improve diffuser usage and significantly reduce variation in performance with VRc. A second AM design used a very large radius of curvature inlet to reduce biasing caused by the inlet crossflow. Experiments showed that this “swept” hole design did minimize biasing of the coolant flow to one side of the shaped hole, and it significantly reduced variations due to varying VRc. RANS simulations at six VR and three VRc conditions were made for each geometry to better understand how the new geometries changed the velocity field within the hole. The sharp and rounded inlets were seen to have very similar tangential velocity fields and jet biasing. Both AM inlets created more uniform, slower velocity fields entering the diffuser. The results of this article indicate that large improvements in film cooling performance can be found by leveraging AM technology.

Engineering↗

NASA NTRS1989

In-flight boundary-layer transition measurements on a swept wing

Flight tests were conducted at three different altitudes to detect transition on a smoothed test region of a swept-wing business jet wing using surface hot-film sensors and sublimating chemicals. Strong influence of sweep angle on transition location was observed when the aircraft was flown at some sideslip conditions to simulate changes in effective wing sweep angle. No effects of engine noise on transition were measured when different engine power settings were used. Flight instrumentation and ground data analysis techniques are described. Correlation was obtained between the hot-film sensor signals and sublimating chemicals for transition detection. Crossflow vortices were observed for one flight condition. Results of analyzed data for various flight-test conditions are presented.

Ahmed, Anwar↗

NASA NTRS1994

Experimental and numerical study of swept ramp injection into a supersonic flowfield

Time-averaged measurements of pressure, temperature, velocity, and injectant mole fraction are presented using the planar laser-induced iodine fluorescence technique in the complex three-dimensional compressible flowfield around a swept ramp fuel injector. Within the range of thermodynamic conditions present in the test case studied, the technique's accuracy is estimated to be 4% for pressure, temperature, and velocity and 3% for injectant mole fraction. Comparisons with numerical simulations using the SPARK three-dimensional Navier-Stokes computer code with an algebraic turbulence model are made at the centerplane of the flowfield as well as on three crossflow planes downstream of the injector. Calculations and measurements are in good agreement throughout the flowfield, with deviations on the order of 5%; however, in specific regions, such as in the base of the ramp, deviations are larger. A weak asymmetry in the incoming flowfield appears to be amplified by boundary-layer separation occurring when the ramp-generated shock reflects off the tunnel walls. Ramp-generated vortices are weaker in the calculated results due to the effects of numerical viscosity in the vortex cores. This leads to less turning and mixing of the jet plume than observed in the experiments. The rate of decay of the maximum injectant mole fraction with streamwise distance is greater for the present ramp injection scheme than for previously measured transverse injection schemes. In this recirculation region at the base of the injector, laminar calculations show better agreement with the measurements than turbulent calculations.

Donohue, James M.↗

NASA NTRS2011

Reynolds-Averaged Navier-Stokes Solutions to Flat Plate Film Cooling Scenarios

The predictions of several Reynolds-Averaged Navier-Stokes solutions for a baseline film cooling geometry are analyzed and compared with experimental data. The Fluent finite volume code was used to perform the computations with the realizable k-epsilon turbulence model. The film hole was angled at 35 to the crossflow with a Reynolds number of 17,400. Multiple length-to-diameter ratios (1.75 and 3.5) as well as momentum flux ratios (0.125 and 0.5) were simulated with various domains, boundary conditions, and grid refinements. The coolant to mainstream density ratio was maintained at 2.0 for all scenarios. Computational domain and boundary condition variations show the ability to reduce the computational cost as compared to previous studies. A number of grid refinement and coarsening variations are compared for further insights into the reduction of computational cost. Liberal refinement in the near hole region is valuable, especially for higher momentum jets that tend to lift-off and create a recirculating flow. A lack of proper refinement in the near hole region can severely diminish the accuracy of the solution, even in the far region. The effects of momentum ratio and hole length-to-diameter ratio are also discussed.

Johnson, Perry L.↗